Installation Instructions 120 volt Nitride Universal Ignitor Upgrade Kit for furnace, boiler or water heater a universal replacement nitride ignitor — for silicone carbide ignitors
We strongly recommend that the installation is carried out by a qualified gas appliance service provider. Warning Follow the recommended installation instructions carefully. Failure to do so will void the warranty and may lead to injury or property damage. Shock Hazard • Always turn off electric power before working on any appliance. • Ensure proper connection to all wires.
Explosion Hazard • Shut off gas to appliance before installation begins, and do not reconnect until installation is complete. Fire Hazard • Under no circumstances exceed the specified voltage of 120 volts. • Ensure that components do not come into direct contact with water (for example, spray, dripping water or rain). • Improper and dangerous operation can result from wiring errors. • Ensure that wiring is routed securely, and away from any flame.
Contents Hazards Wa rnings Inside front cover Ignitor Specification 2 3 Ignitor Dimensions 4 Installation Instructions Check Out Instructions 5 Ignitor Assembly Drawings 6 Because of continued improvement to the product, White-Rodgers reserves the right to alter specification.
Ignitor Dimensions Nitride heating element 1.97” Heater cemented into ceramic insulator using white ceramic cement Bracket stainless steel 304 - bright finish Ceramic insulator body non glazed 95% alumina polished finish 1.18” Cable - PTFE 7 strand/20 gauge U/L Specification temperature rating 250ºC 14.
Installation Instructions Please read all these instructions to the end carefully before beginning installation. 1. Turn off the gas and electrical supply and then identify which type of ignitor is inside your appliance. See pages 6--Inside back cover. . your existing ignitor retaining all 2. Unplug fittings, and match it up with the diagrams. 3. Compare the position of the alignment tag on your existing ignitor carefully to the top view diagrams. Ensure that you have the correct ignitor type. 4.
8. Take the wire nuts provided and screw down tight over the joined stripped wires, ensuring that no wires are showing. 9. Check installation is secure and safe, routing leads away from the burner. Check Out Instructions 1. Turn on the gas and electrical supply to the appliance. 2. Turn the room thermostat to call for heat. 3. Test appliance for proper ignition and operation. 4. Verify that the Power-On LED is on during the warm-up. 5.
Ignitor Assembly 1 Ensure that you have this ignitor base. Original Silicon Carbide ignitor viewed from the top. Note the position of the alignment tab bottom left. Tab B Tab C Tabs B and C removed from the universal bracket.
Ignitor Assembly 1 Silicon Carbide ignitor to be replaced. The universal bracket should look like this. Completed assembly of Nitride replacement kit should look like this.
Ignitor Assembly 2 Ensure that you have this ignitor Base. Original Silicon Carbide ignitor viewed from the top. Note the position of the alignment tab bottom right. Tab C Tab A Tabs A and C removed from the universal bracket.
Ignitor Assembly 2 Silicon Carbide ignitor to be replaced. The universal bracket should look like this. Completed assembly of Nitride replacement kit should look like this.
Ignitor Assembly 3 Ensure that you have this ignitor Base. Original Silicon Carbide ignitor viewed from the top. Note the position of the alignment tab top left. Tab B Tab A Tabs A and B removed from the universal bracket.
Ignitor Assembly 3 Silicon Carbide ignitor to be replaced. The universal bracket should look like this. Completed assembly of Nitride replacement kit should look like this.
Ignitor Assembly 4 Ensure that you have this ignitor Base. Original Silicon Carbide ignitor viewed from the top. Tab B Tab C Tabs B and C removed from the universal bracket.
Ignitor Assembly 4 Silicon Carbide ignitor to be replaced. The universal bracket should look like this. Completed assembly of Nitride replacement kit should look like this.
Ignitor Assembly 5 Ensure that you have this ignitor base. (See note on Assembly 6) Original Silicon Carbide ignitor viewed from the top. Tab B Tab C Tabs B and C removed from the universal bracket.
Ignitor Assembly 5 Silicon Carbide ignitor to be replaced. The universal bracket should look like this. Completed assembly of Nitride replacement kit should look like this.
Ignitor Assembly 6 Ensure that you have this ignitor base. Original Silicon Carbide ignitor viewed from the top. Adaptor plate † Depending on ignitor type, some 5 and 6 assemblies might: 1) be assembled using either bracket 5 or plate 6, or 2) require combining with some original fittings.
Ignitor Assembly 6 Silicon Carbide ignitor to be replaced. The adaptor plate should look like this. Completed assembly of Nitride replacement kit should look like this.
