User Manual Copyright ⓒ 2019. Lab-T, Inc.
EN
EN USER INSTRUCTIONS AND SAFETY Congratulations on your purchase of a Nolangroup N-Com product. N-Com B601 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about B601, and to download high-definition instructions as well as the latest Firmware version, visit the website www.n-com.it Firmware Version: 1.
Contents 1. WARNINGS AND SAFETY 1.1.Road safety ................................................................................................................................................................................ 4 1.2.Switching on the system in safe environments .......................................................................................................... 4 1.3.Interferences.............................................................................................................
EN 1. WARNINGS AND SAFETY Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like. Caution: Installation of the N-Com B601 system results in a weight increase of approximately 100g, which is added to the weight of the helmet and of the other accessories.
Caution: An incorrect installation of the system in the helmet may alter the aerodynamic and safety characteristics of the helmet itself, thus creating dangerous conditions. Install the N-Com system according to the instructions provided in the product documentation. In case of doubt, please contact your local N-Com dealer. Warning: Listening to other equipment should not interfere with driving the vehicle, which must be the top priority at all times.
EN 2.
3. INSTALLATION ON THE X-903 HELMET The X-903 helmet is pre-set for the EASYFIT simplified installation of the N-Com system. Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 18.5). The installation video can be seen at www.n-com.it / Support section. 3.1.
EN Note: In the event that the keyboard is not positioned correctly, peel it off right away with extreme care and repeat the positioning. Note: It takes up to 24 hours for the keyboard to stick completely. During this time, do not expose the helmet to atmospheric agents. Line up the keypad flex connector to the e-box making sure that the letter “n” is pointing as shown in Fig. 6. Gently position the connector in its seat until it is all the way in (Fig. 7).
3.3. Positioning the microphone in the X-903 helmet Hook up the specific microphone for full-face helmets in its seat in the chin guard (Fig. 13). Position the microphone wire in the vertical groove (Fig. 14) and afterwards behind the cheek pad lining. If necessary, lift up the groove tabs and the cheek pad lining using a flat head tool (supplied as standard equipment). Fig. 13 Fig. 14 Fig. 15 Hook up the microphone to the connector coming out of the eBox (Fig. 15).
EN Fig. 19 Fig. 20 Fig. 21 Position the right loudspeaker in its housing, inserting the cable in the special groove (Fig. 22). If necessary, secure the earphone using the adhesive supplied as standard equipment. Position the wiring and the connectors behind the cheek pad lining, lifting it up with the help of a flat head tool. Fig. 22 3.4. Repositioning the padding Reposition the internal comfort padding by following the specific instructions provided in the helmet user manual.
4. INSTALLATION ON THE X-LITE HELMETS This procedure must be followed for the installation of N-Com systems on X-lite helmets other than model X-903. Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 18.5). The installation video can be seen at www.n-com.it / Support section. 4.1. Preliminary operations Remove the internal comfort padding by following the specific instructions provided in the helmet user manual.
EN ONLY FOR X-702 HELMET: Fig. 27 Fig. 28 Position the battery connector and wiring underneath the shell gasket (Fig. 27). Cut along the pre-cut lines of the plastic tab on the back of the comfort padding (Fig. 28). Secure the wiring underneath the plastic tab. Close the cut parts using the cable fixing adhesives (Fig. 29). Fig. 29 Remove the small N-Com cap positioned on the left side of the helmet. To make the operation easier, we recommend pushing the cap from inside the helmet (Fig. 30).
Note: In the event that the keyboard is not positioned correctly, peel it off right away with extreme care and repeat the positioning. Note: It takes up to 24 hours for the keyboard to stick completely. During this time, do not expose the helmet to atmospheric agents. Line up the keypad flex connector to the e-box making sure that the letter “n” is pointing as shown in Fig. 34. Gently position the connector in its seat until it is all the way in (Fig. 35).
EN Fig. 38 Fig. 39 Fig. 40 On certain helmets, the housing for the microphone rod must be created by cutting out the helmet border gasket along the precut area (Fig. 41). Fig. 41 FULL-FACE HELMETS Take the polystyrene check pad (left side) and position the microphone in the special housing, as illustrated in Fig. 42, being careful that the side of the microphone support with the letter “n” is facing towards the inside of the helmet (Fig. 43).
4.4. Repositioning the padding Pass the USB mini wire through the elastic band found on the comfort padding. Replace the internal comfort padding by following the specific instructions found in the helmet user manual. Warning: Always verify the proper length of your chinstrap and adjust it if necessary, referring to the specific helmet instructions.
EN 6. BASIC FUNCTIONS Note: Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely. Press “n” and keep it pressed for about 2 seconds, until the LEDs turn on and you hear the voice announce ment.
7. CONFIGURATION MENU All Bluetooth pair ups and other adjustments are carried out in this mode. To put the system in “Configuration mode” (starting from a switched off system) press the “n” key and keep it pressed for 4 seconds, until you hear the voice announcement “Configuration”. Once in the “Configuration” menu, press the keys“-” and “ ” to scroll through the various menu items.
EN 9. MOBILE PHONE To pair up a mobile phone to the B601 system, follow the procedure illustrated in Chapter 8. Answering a phone call Briefly press any key when you hear the incoming call signal. Voice call Press “n” and keep it pressed for about 2 seconds. Hanging up/rejecting a phone call Press “n” and keep it pressed for about 2 seconds. Manual phone connection Press “n” and keep it pressed for about 2 seconds. 9.1.
9.2. Conference call function When a call comes in on a mobile phone connected via Bluetooth to B601, the intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call. Turning on the phone conference call function During the phone call, briefly press “n” (channel 1). During the phone call, press the “n” key twice (channel 2). During the phone call, press the “n” key three times (channel 3).
EN 12. MUSIC VIA BLUETOOTH To pair up an Mp3 device to the B601 system, follow the procedure illustrated in Chapter 8. Play music (Play) Press “▲ ” and keep it pressed for about 2 seconds. Pause function (Pause) When the player is playing music, press “▲ ” for 2 about seconds. Next track (Skip) When the player is playing music, press “▲ ” for 4 about seconds. Previous track (Rew) When the player is playing music, press “▼ ” for 4 about seconds. 12.1.
14. N-COM INTERCOM The N-Com B601 system allows communication with other N-Com systems, up to a maximum distance of about 250 m (in open field, with no obstacles). The range of the communication varies depending on the N-Com systems used. Important: The procedure described below refers exclusively to the pairing up and operation between the B601 and the “900” / “600” series N-Com systems.
EN 15. “ UNIVERSAL INTERCOM ” INTERCOM The N-Com B601 system can be connected via Bluetooth to intercom systems of other brands or to NCom systems other than the “900” ! “600” series, thanks to the UNIVERSAL INTERCOM function. Important: N-Com systems other than the “900” ! “600” series must be paired up to the N-Com B601 by following the procedure “Pairing up the Universal Intercom”. 15.1.
16. BATTERY AND RECHARGE 16.1. Low battery signal During its operation, the system alerts the user with a voice message when the battery is low. From the first message, the system has a 1-hour autonomy. Warning is given every 10 minute. 16.2. Checking the Battery Level LED Indicator When the system is powering on, their blue LED flashes rapidly indicating the battery level.
EN 17.
18. LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: Read the cautions pertaining to safety and proper use. Read the warranty terms and conditions. Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 18.1.
EN 18.3. Validity of this limited warranty This warranty is valid only if the enclosed warranty form is duly and completely filled out with the following information: Product identification code Name and stamp of the authorized dealer. Product purchase date. Buyer’s name and address. Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer. 18.4.
WARRANTY REGISTRATION FORM Product name B601 X SERIES Identification code Buyer ’ s Information Name Last name Address Phone e-mail Dealer ’ s stamp Date of purchase 27
FCC, IC Warning statement Certification and Safety Approvals FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Déclaration de conformité IC (Industrie Canada) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
www.n-com.
