EN USER INSTRUCTIONS AND SAFETY Firmware Version: 1.
Congratulations on your purchase of an N-Com product. N-Com B1.4 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about B1.4, and to download high-definition instructions as well as the latest Firmware version, visit the website www.ncom.it REFERENCE STANDARDS The products of the N-Com line are in compliance with standards as per the table below: B1.
Contents 1. WARNINGS AND SAFETY ................................................................................................. 4 1.1.Road safety ................................................................................................................................................................ 4 1.2.Switching on the system in safe environments ......................................................................................... 4 1.3.Interferences..........................................
1. WARNINGS AND SAFETY Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com B1.4. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like. Caution: Installation of the N-Com B1.
B1.4 1.4. Appropriate use Use the device only in the normal position, as described in the product documentation. Do not attempt to disassemble, tamper with or modify any part of the N-Com system. Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use the system on the road. Caution: Adjusting the volume to very high levels may cause damage to your hearing.
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: The presence of a crossed-out wheelie bin indicates that in the European Union the product is subject to separate collection at the end of its useful life (European Directive 2002/96/EC).
B1.4 3. INSTALLATION You can download the installation video from www.n-com.it N-Com / Download section. Before you install the B1.4 system on the helmet, make sure it turns on properly. Press the “on” key for about 2 seconds, until the LED lights up and you hear a beep in the headset. Proceed with the installation. Remove the cheek padding (see helmet instructions). Remove the helmet edge gasket using the special tool (Fig. 1).
Option 1 Option 2 N.B.: Keep the filling material in case you wish to use the helmet without the N-Com system in the future. Place the system in the special housing in the back of the helmet, pushing it all the way into the groove (Fig. 3). Fix the cable inside the helmet and make sure the right fixing clip snaps into its housing (Fig. 4) Fig. 3 Fig.
B1.4 Position the microphone in the housing on the left of the helmet, inserting the metal boom in the groove found in the chin guard coupling frame (Fig. 5). Caution: make sure that the side of the microphone support with the writing “N-Com” is facing inward. Fig. 5 Fix the cable inside the helmet and make sure the left fixing clip snaps into its housing. Hook up the keypad to the helmet by clicking in the relevant hooks. Fig.
3.1. Removing the B1.4 system from the helmet Proceed as follows to remove the B1.4 system from the helmet: Remove the cheek padding and the shell gasket; Remove the keypad from the shell, using a flat head screwdriver (or a similar tool) to lever upwards in the special hollow as shown in fig. 7. Unhook the right and left clips from the shell, levering upward using a flat head screw (or a similar tool), as shown in figure 8. Fig. 7 Fig. 8 10 Completely remove the B1.
B1.4 4. BASIC FUNCTIONS System ON System OFF Increase Volume Decrease Volume 4.1. Press “on” and keep it pressed for about 2 seconds, until the LEDs turn on and you hear a beep in the headset. Press “on” and keep it pressed for about 4 seconds, until the LEDs turn off and you hear a beep in the headset. Briefly press “” to increase the volume. A double tone signals the highest volume level. Briefly press “” to decrease the volume. A double tone signals the lowest volume level.
5. PAIRING UP BLUETOOTH DEVICES In order for the B1.4 system to be connected to another Bluetooth device, the latter needs to be first paired up with the N-Com system. The pairing up procedure is the same for all Bluetooth devices: mobile phones, MP3 Bluetooth players, satellite navigators, etc. 1. Make sure the B1.4 is turned off; 2. Press “on” and keep it pressed (for more than 6 seconds), until the LEDs start to flash quickly and you hear a sharp beep in the headset, indicating the “Pair-up mode”; 3.
B1.4 6.
8. BLUETOOTH A2DP MUSIC PLAYER You can listen to high quality music by connecting B1.4 to a device equipped with Bluetooth A2DP (Advanced Audio Distribution Profile) protocol. The B1.4 system is also equipped with Bluetooth AVRCP (Audio Video Remote Control Profile) protocol, which allows you to stop and resume music reproduction directly from the helmet (with devices equipped with AVRCP). Connection to A2DP music player Play music (Play) The connection is automatic when you turn on the system.
B1.4 10.2. Intercom function To activate the intercom connection, turn on the two N-Com systems and briefly press “on” on one of the helmets. Intercom activation With B1.4 turned on, briefly press “on”. Intercom deactivation With B1.4 turned on, briefly press “on”. 11. BATTERY Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times.
12.
B1.4 13. LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - Read the cautions pertaining to safety and proper use. - Read the warranty terms and conditions. - Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 13.1.
Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer. 13.4.
14. WARRANTY REGISTRATION FORM Product name: B1.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
www.n-com.it B1.4 rel.
