User's Manual

headset/ audio receiver. The blue LED will flash in
middle speed to indicate Tx is transferring audio.
4. If the connection lost by out of range, take the
Bluetooth stereo headset/ audio receiver back to Tx
within 10 feet. Tx will reconnect it automatically.
Tips: The auto-reconnection function will just effect in 15
seconds after the connection lost. If a new Bluetooth stereo
headset/ audio receiver is available (in pairing mode), Tx will
try to pair with it and continuous the music transfer with the
new paired Bluetooth stereo headset/ audio receiver.
Otherwise Tx will goes into Idle mode to save power, the blue
LED will flash in slow speed.
VISUAL INDICATION
LED can also indicate the status of Tx
Statues indication
paring or
connecting to
the other device
High speed flash, which flashes 10
times per second
Connected, or
music
transferring to
the other device
Middle speed flash, which flashes once
per second
Idle mode Low speed, which flashes once per 5
seconds
TROUBLE SHOOTING
Please note that you should also be familiar with the
operation of your Bluetooth stereo headset/ audio receiver.
Please read your Bluetooth stereo headset/ audio receiver
user guide carefully. Please note that the Tx will only work
with Bluetooth stereo headset/ audio receiver or receiver with
support the Bluetooth AV profiles.
Symptom/Problem
Solution
When power on Tx, no
LED flashes
•
Check battery power.
• Consult authorized dealer
Tx powers on with
blue LED quick
flashing but no
connection to
Bluetooth stereo
headset/ audio
receiver
• Check power of your
Bluetooth stereo headset/
audio receiver
•
Check the pin code of you
Bluetooth stereo headset/
audio receiver, refer to the
user guide of your stereo
headset/ audio receiver
• Ensure Rx & phone are within
range
CUSTOMER SERVICE INFORMATION
For other Nolan Bluetooth products or support, please
view our website – www.nolan-sys.com
or email
[e-mail] or contact your local representative.
DISCLAIMER
Whilst every effort has been made to ensure that the
information in this manual is accurate and complete, no
liability will be accepted for any errors and/or omissions
made. The manufacturer reserves the right to make
changes and improvements to the specifications and
features of the hardware and firmware of the products
described in this document without prior notice.
Reproduction, transfer, distribution or storage of part or all
of the contents in this document in any form is prohibited
without prior permission of the manufacturer. All
trademarks acknowledged.
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the
user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void
your authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. End users must follow the
specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Notice: Any changes or modification not expressly approved by
the party responsible could void the user's authority to operate
the device.