TECHNICAL MANUAL
Important warnings If these warnings are not duly observed, your equipment may get damaged. During each power-up, the Golden King Deep Processor Radar system should be held as shown in the picture. The 'ON' key should be pressed in this position. After pressing the 'ON' key, keep your position still for approximately 20 seconds. Then lower the search coil to the normal searching height, press 'RESET' and release. When the above process is finished you can do the ground balancing and start your search.
Special Regulations Comply with the law and the regulations applicable to any given place. Do not use the device at the protected areas and the military zones. You should definitely inform the concerned authorities of any cultural findings you may find during your search. Battery If you use another type of battery instead of that prepared by Nokta Engineering which is equipped with protection circuits, your unit may get damaged.
Features of the Equipment Language Selection Monitor On the Golden King Deep Processor Radar system, a 7’ TFT screen with 800 X 480 resolution, 262.000 colors and 16-bit color depth is used. Construction The Golden King Deep Processor Radar is constructed with thermoset engineering plastic. It has very high durability and is affected by extreme hot and cold weather conditions at a minimum level.
Features of the Equipment Ferrous Setting Camera Recorder During your search with the Golden King Deep Processor Radar, you can search by switching the ferrous setting to OFF to avoid ferrous metals (iron, nail, beverage bottle caps, etc.). The Golden King Deep Processor Radar is equipped with a special camera recorder as an attachable accessory which operates at a very high display quality even 30 meters under water, has night vision, thus allowing use both on land and under water.
Contents Unpacking 1 Ground balance Make sure all the parts are present.
Unpacking Make sure all the parts are present. • • • • • • • • • • • System box Extension pipe Battery box Charger Leather case Surface search coil (optional) General search coil Deep search coil (optional) Camera Recorder (optional) Gas sensor (optional) Headphones All these parts can be obtained from the dealers of Nokta Engineering. Please do not use any external or any other branded item.
Equipment System Box Camera recorder input Headphones socket input Gas sensor socket input Battery Search coil socket input Battery compaction apparattus Battery compaction apparattus 2
Plug it into a 220V wall socket. Starting Initial steps to operate the equipment Preparing and charging the equipment You are required to charge the battery before initial use. The battery should be charged for about 3-4 hours. Under normal conditions, the battery should allow 5-6 hours of operation. For soils containing high density of minerals, this term reduces down to 4-5 hours. Note: The battery charger used on the system is equipped with a special software.
Starting Assembly The extension bar to which the armlet and the joystick are connected is removed from the bag. The search coil is attached to the bobbin connection component on the extension bar with the bobbin clamping screws. The connector at the end of the extension bar is inserted in its place on the search coil and the connector next to the armlet is inserted in its place on the system box.
Starting Keys and Screen Standby Key It is the key to turn off the entire system. On / Off Switch After charging the battery, turn the system off by pressing the OFF button and place the battery box in its place on the system box. Then, in order to turn on the system, press the ON button on the battery box. In order to turn off the system, first you need to press the STANDBY button on the keypad. Then you need to press the OFF button on the battery.
Starting Ground Balance Key This key is used to access the ground balance menu. You can select either the automatic or the manual option from the ground balance menu when needed. Left Direction Key It is the left direction key to go leftward on the options on the menu screens. Brightness Setting Once the brightness setting key is pressed, it brings up the brightness setting menu. In this menu, you can set the screen brightness to any level you need.
Starting Numeric Keys It is the multi-functional section of the keypad. Especially at the time of recording, it lets you enter the Date / Region / Name and the Time. Press the key until the character you desire appears on the screen. You can delete any letter or number by using the DEL key. After entering a text or a number, press the OK key to save. Screen Do not expose your monitor to fire directly. Protect your monitor against excessive hot, excessive cold or rain.
Starting Accessing Menu Functions Detection There are 2 methods to access the menu functions of the Golden King Deep Processor Radar. To search with the Golden King Deep Processor Radar, you should select one of the two interface options. Method 1: Is the multi-functional keypad on the system box. You can access the menu functions by using the keys here.
Starting Saving detections You can save the findings obtained by the Golden King Deep Processor Radar as well as the result screen reports and graphs. In order to save the result screens, you can use the save key on the keypad. If you do not want to save the result screen, press the “BACK” key and return to the ground balance selection screen. When you press the “SAVE” key, the following window will appear on the screen. You should enter the required information on the window.
Starting Accessing the stored data In order to access the «3D RESULT» and the «CAMERA» recordings press the «SAVE» key on the keypad. The archives screen will appear on your monitor.
Starting Use of Additional Features 3D RESULT 3D RESULT: You can view the 3D result screens you have previously saved in the Golden King Deep Processor Radar system. To view the 3D result screens, please press the «SAVE» key on the keypad. Using the right/left direction keys, you can select the «3D RESULT» tab and press the «OK» key.
Use of Additional Features After the camera’s socket is inserted into the camera recorder’s input jack, press the camera key on the keypad. Approximately within 15-20 seconds, the interface below will come up. Here the camera is in the preview mode and it will show the current view. PLEASE ENTER DATE / NAME / REGION INFO BY USING LETTERS AND NUMBERS ON THE KEYPAD. DATE PLAY _ _ /_ _ /_ _ _ _ NAME _________ REGION _________ AFTER COMPLETION OF NAMING, PRESS “OK” KEY.
Use of Additional Features PAUSE PAUSE STOP ½X ¼X DATE NAME PAUSE BUTTON REGION 0 2 /0 4 /2 0 0 8 RECORD1 I STAN B U L 0 5 /0 4 /2 0 0 8 RECORD2 ADANA__ 1 1 /0 4 /2 0 0 8 RECORD3 BITLIS__ 1 6 /0 4 /2 0 0 8 RECORD4 HATAY_ _ 2 9 /0 4 /2 0 0 8 RECORD5 EDIRNE_ When viewing the saved videos, you can pause any moment of the video indefinitely by using the “PAUSE” button. This way, you can view the videos you have recorded in more detail.
Use of Additional Features ½X ½ X BUTTON ¼X ¼ X BUTTON If slower viewing is needed, press the “¼ X” button to watch the video recorded on 30 fps as 7 fps. The video will now play at 1/4 of the normal speed. When viewing the videos you have recorded, your system is designed to display 30 frames per second (fps). This frame speed is the standard video format. When you want to watch the video in slow motion, the system offers two alternatives to the user. First is the “½ X” button.
Use of Additional Features Gas Sensor The Golden King Deep Processor Radar system is equipped with a gas sensor which measures and informs the user of the presence of methane gas which is one of the flammable, explosive and toxic gases in confined places. You can reach the video recordings of the regions you have previously searched through the «ARCHIVES» screen. You can also obtain the signal map of the regions you have searched by the archive feature of the system.
Use of Additional Features After measuring, the user is warned by one of the two results: First one is: “SAFE METHANE LEVEL” “THERE MAY BE DIFFERENT GASES, WEAR GAS MASK FOR YOUR SAFETY” The gas sensor socket input is shown in the picture below.
Use of Additional Features Headphones Use of the Search Coil When designing the Golden King Deep Processor Radar, it was our first and one of the most important goals to consider all the needs of the user on the field and to provide the best results while fulfilling these needs. Frequency range 20 ~ 20,000Hz Impedance 32 ohm Sensitivity 105dB ± 3dB(at 1kHz) Maximum input power 100mW Jack 3.5mm Stereo Cable 2.5m±%10 Therefore, we have developed the SMART SEARCH COIL system.
Use of Additional Features Surface Search Coil (210x315mm) This search coil which is very sensitive to small objects and to those that are close to the surface, is capable of getting results up to 3 meters depth. It is very ideal for single coin searches and it is very sensitive to small metals on the surface like no other searh coil is. You can, if you like, switch off the “FERROUS” mode on your system and search whill avoiding any undesired ferrous metal (beverage bottle caps, nails, wires or cans, etc.).
Use of Additional Features Deep Search Coil 600x1000mm As you will not be able to use the «RESET» and the «CONFIRM» buttons on the joystick once you connect this search coil, the buttons on the search coil carrying hangers are used for performing the reset and the confirm functions.The green button is used for the «CONFIRM» function and blue button is used for the «RESET» function.
Ground Balance AUTOMATIC GROUND BALANCE Ground Balance On the Golden King Deep Processor Radar system, ground balancing is done through the “GROUND BALANCE” menu. You can access the ground balance menu both from the settings section or by pressing the “GROUND BALANCE” key on the keypad. OK What you need to do is to eliminate the soil in the box on the left side of the screen and turn it to green and save it by pressing the «OK» button.
Ground Balance After pressing the «RESET» button, following the animated guide on the screen, hold your search coil about 10cm above the ground again and press the «CONFIRM» button. Please wait until the clock on the screen makes one complete turn after pressing the «CONFIRM» button. AUTOMATIC GROUND BALANCE MAXIMUM LOWER LEVEL Please continue these steps until the box with the soil on the left side completely turns to green.
Ground Balance Raise the search coil 40cm above the ground and press the “- / +” key on the keypad for an estimated number of times to eliminate the effect. Because the effect is in the positive direction in the example below, you should press the “+” key. If the incoming effect was negative, then you would press the “-“ key. MANUAL GROUND BALANCE When “MANUAL GROUND BALANCE” is selected, you will see the interface below.
Ground Balance Detection Functions RESET BUTTON Interface Selection The Golden King Deep Processor Radar system offers two types of detection interfaces. First one is “ DIGITAL” and the second one is “GAUGE” interface. The user can search by selecting the interface which he/she will use most conveniently. These interfaces can be changed anytime through the interface selection menu.
Detection Functions DIGITAL DETECTION Nokta ENGINEERING GENERAL DETECTION YOU DETECTED A TARGET! PLEASE HOLD “CONFIRM” BUTTON AND PASS OVER THE TARGET TO GET ALL INFORMATION ABOUT THE TARGET. SCOPE SCREEN With the Golden King Deep Processor Radar, you will easily follow the amplitude of the target signal in real time on the SCOPE Screen. On this screen, you will both see the highest amplitude point of the signal center in real time and examine the signal graphs of both the cavities and the metal targets.
Detection Functions YOU DETECTED A TARGET ! PLEASE HOLD “CONFIRM” BUTTON AND PASS OVER THE TARGET TO GET ALL INFORMATION ABOUT THE TARGET. GOLD 73 CAVITY 21 MINERAL 68 METAL min 30 max 23 MINERAL YOU DETECTED A TARGET ! PLEASE HOLD “CONFIRM” BUTTON AND PASS OVER THE TARGET TO GET ALL INFORMATION ABOUT THE TARGET. REPORT SCREEN The Golden King Deep Processor Radar communicates the initial data received from the target signal and the following steps to be performed through the REPORT SCREENS.
Detection Functions YOU DETECTED A TARGET! PLEASE HOLD “CONFIRM” BUTTON AND PASS OVER THE TARGET TO GET ALL INFORMATION ABOUT THE TARGET. 73 CAVITY 21 MINERAL CAVITY SECTION GAUGE It is the section of the GAUGE DETECTION interface which gives cavity data. In this section, you will follow the target signals and read them in percentage figures. Due to the gauges, you will see and examine the status of the signal received from the target in real time.
Technical Characteristics Result Screen Result Screen You can examine the 3D graph of the target signal on the result screen of the Golden King Deep Processor Radar in real time. On the result screen, there are 3 graph windows. 1st window is the top view of the signal, 2nd window is the side view of the signal and the 3rd window is the perspective view of the signal. On the vertical guide scale to the left of the 3D perspective image, you can see the amplitude of the target signal.
Menu Description LANGUAGE SELECTION LANGUAGE SELECTION MENU: It consists of 10 languages: Turkish, English, Greek, Persian, Bulgarian, Arabic, French, Spanish, German and Russian. Once the user selects a language, the whole system switches to that language instantly. OPERATING MANUAL OPERATING MANUAL MENU: The operating manual is full of information that you can refer to anytime you want. It consists of Warnings, Correct trial, Incorrect trial and Useful information.
Menu Descriptions GOLD 68 METAL DIGITAL 30 MINERAL GAUGE INTERFACE SELECTION AUTOMATIC MANUEL GROUND BALANCE GAS SENSOR INTERFACE SELECTION MENU: Interface selection consists of 2 alternatives to provide you with a more convenient use during your search. You can select the one you want by using the right/left direction keys and save it by pressing “OK”. GROUND BALANCE MENU: The system provides the user with two alternatives to do ground balancing.
Exemplary Use 1 In this presentation, we have explained everything about the operation of the equipment from start up to finding the target signal with graphics and texts. You can practice searching by following this presentation. We, as Nokta Engineering, have focused on the ease of use for this system. Your searches and detections with the GOLDEN KING DEEP PROCESSOR RADAR which incorporates everything you have dreamed about will become an extraordinary pleasure.
4 3 +100 BRIGHTNESS SETTING PLEASE SET THE VOLUME OF YOUR SYSTEM BY USING THE RIGHT-LEFT DIRECTION KEYS. TO EXIT THE MENU, PRESS THE “BACK” KEY. 5 PLEASE SET THE BRIGHTNESS OF THE SCREEN. TO EXIT THE MENU, PRESS THE “BACK” KEY. 6 FERROUS SETTING PLEASE SET THE SENSITIVITY LEVEL. THE RECOMMENDED SENSITIVITY LEVEL IS +80 UNTIL YOU GET ACCUSTOMED TO THE EQUIPMENT. SET THE LEVEL BY USING THE RIGHT/LEFT DIRECTION KEYS. TO EXIT THE MENU, PRESS THE “BACK” KEY.
7 8 GROUND BALANCE PLEASE SELECT EITHER THE AUTOMATIC OR THE MANUAL GROUND BALANCE USING THE RIGHT/LEFT DIRECTION KEYS. TO EXIT THE MENU, PRESS THE “BACK” KEY. PLEASE SELECT THE DETECTION SCREEN USING THE RIGHT/LEFT DIRECTION KEYS. TO EXIT THE MENU, PRESS THE “BACK” KEY. 10 9 AUTOMATIC GROUND BALANCE AUTOMATIC GROUND BALANCE MAKSÝMUMUPPER ÜST SEVÝYE MAXIMUM LEVEL MAKSÝMUM ÜST SEVÝYE MXIMUM LOWER LEVEL 40cm Reset Button OK 10CM 10cm PLEASE HOLD THE SEARCH COIL 10cm. ABOVE THE GROUND.
12 11 Confirm Button AUTOMATIC GROUND BALANCE AUTOMATIC GROUND BALANCE MAXIMUM LOWER LEVEL MAXIMUM UPPER LEVEL MAKSÝMUM ÜST SEVÝYE Reset Button CONFIRM 10cm RESET 40cm 40cm 10cm NOW LOWER THE DETECTION COIL TO 10cm ABOVE THE GROUND AS SHOWN IN THE ANIMATION. AFTER PRESSING THE CONFIRM BUTTON WAIT UNTIL THE COUNTER COMPLETES A FULL TURN. PLEASE RAISE YOUR SEARCH COIL TO 40cm ABOVE THE GROUND AGAIN AND PRESS THE «RESET» BUTTON.
15 16 Confirm Button AUTOMATIC GROUND BALANCE MAXIMUM LOWER LEVEL CONFIRM 10cm WHEN THE BOX COMPLETELY TURNS TO GREEN, IT MEANS THAT THE GROUND BALANCE IS COMPLETED SUCCESFULLY. AFTER THE GROUND BALANCE IS COMPLETED, A MESSAGE INDICATING THE START AND THE END SENSITIVITY LEVELS APPEARS ON THE SCREEN. NOW YOU CAN START SEARCHING BY PRESSING THE «OK» BUTTON. THE SEARCH DISTANCE FROM THE GROUND SHOULD BE 15-20cm (ABOUT 1 HAND DISTANCE).
19 20 Confirm Button Confirm Button YOU DETECTED A TARGET! YOU DETECTED A TARGET! PLEASE HOLD “CONFIRM” BUTTON AND PASS OVER THE TARGET TO GET ALL INFORMATION ABOUT THE TARGET. Reset Button Reset Button PLEASE HOLD “CONFIRM” BUTTON AND PASS OVER THE TARGET TO GET ALL INFORMATION ABOUT THE TARGET. TO CHANGE YOUR DIRECTION, PRESS THE “RESET” ONCE. HOLD THE “CONFIRM” BUTTON PRESSED AND PASS OVER THE TARGET FOR THE LAST TIME. TO EXIT THE MENU, PRESS THE “BACK” KEY.
23 24 IF YOU DESIRE TO SAVE 3D RESULT SCREEN, PRESS SAVE KEY ON THE KEYPAD. DATE _ _ /_ _ /_ _ _ _ NAME _________ REGION _________ TO EXIT WITHOUT SAVING, PLEASE PRESS BACK KEY. YOU CAN VIEW THE TARGET SIGNAL ON FULL SCREEN BY PRESSING THE “1” KEY ON THE KEYPAD AND YOU CAN ROTATE AND EXAMINE THE SIGNAL BY USING THE “2” - “3” - “4” KEYS. YOU CAN EXIT THE MENU BY PRESSING “BACK”. YOU CAN SAVE THE RESULT SCREEN BY HOLDING THE “SAVE” KEY PRESSED.
ATTENTION! The Golden King Deep Processor Radar is the best system produced so far among the systems that receive data from underground. The detector and radar systems delivering 100% performance on land or in the sea do not operate with 100% accuracy underground. Scientifically, it is not possible to get 100% accurate results. With respect to the results it gives, the Golden King Deep Processor Radar is the ultimate point in technology.
