LCD Projector NP3250/NP2250/ NP1250/NP3250W WPA Setting Guide Supported Authentication Method WPA-PSK WPA-EAP WPA2-PSK WPA2-EAP Sec urity Network WPA Security Se cu T S SHI LEF LEN FT RIG HT WN DO UP SELE CT 3D REFO RM AUTO ADJU ST SOU RCE AN /ST ON USB D BY WIRELESS WIRELESS LAM STAT P POW US ER rity
Contents Introduction........................................................................................................ 3 1. Setting WPA-PSK or WPA2-PSK..................................................................... 5 2. Setting DATE, TIME PRESET........................................................................... 8 3. Setting WPA-EAP or WPA2-EAP..................................................................... 9 4. Checking Authentication Status on [INFORMATION] Screen.................
Introduction Thank you for purchasing the LCD Projector NP3250/NP2250/NP1250/NP3250W. This guide explains how to set the enhanced wireless LAN security (authentication method) on the projector as shown on the table below. Set the projector according to the security environment of your network.
Other Notes • Contact your network administrator for information about access point and settings for authentication server (authentication method, encryption type, EAP type, and digital certificates). • For using the on-screen menu on the projector, see the “User’s Manual” (PDF) on the supplied CD-ROM. • See the supplied “Wired and Wireless Network Setup Guide” for instructions on setting IP address, subnet mask, SSID, and WEP on the projector.
1. Setting WPA-PSK or WPA2-PSK From the on-screen menu on the projector, select [SETUP] → [INSTALLATION(2)] tab → [NETWORK SETTINGS] screen and follow the instructions below. ➊ Display the [NETWORK SETTINGS] screen. • See page 17 of “Wired and Wireless Network Setup Guide” for setting wireless LAN. ➋ Use the SELECT ▶ button to select the [WIRELESS] tab. The [WIRELESS] page will be displayed. ➌ Set items such as PROFILE, DHCP, IP ADDRESS, SUBNET MASK and others as required.
➏ Use the SELECT ▼▲ button to select a connecting SSID, and then press the SELECT ▶ button to select [OK]. Finally press the ENTER button. • Select the SSID for which WPA-PSK or WPA2-PSK is set. • Select [INFRASTRUCTURE ( )] for [NETWORK TYPE]. WPA-PSK, WPA2-PSK, WPA-EAP, or WPA2-EAP is not available when [AD HOC ( )] is selected. ➐ Use the SELECT ▲ button to select the [CONNECTION] tab and then SELECT ▶ button to select the [SECURITY] tab. The [SECURITY] page will be displayed.
⓬ Use the SELECT ▼ button to select the [KEY] field and press the ENTER button. The character entry screen (software keyboard) will be displayed. Set a key. • A key must be between 8 and 63 characters in length. • See page 26 of “Wired and Wireless Network Setup Guide” for using the software keyboard to enter a key. ⓭ Use the SELECT ▼ button to select [OK] and press the ENTER button. The [WIRELESS] page will be returned. ⓮ Use the SELECT ▼ button to select [RECONNECT] and press the ENTER button.
2. Setting DATE, TIME PRESET Before installing a digital certificate on the projector, you are required to set [DATE, TIME PRESET] for checking the expiration date of the digital certificate. Set the current date and time (i.e., local time), and the time zone. Important: • If setting of [DATE, TIME PRESET] is not correct, a message “authentication error” will be displayed because of failure of checking the expiration date of the digital certificate when you install a digital certificate.
3. Setting WPA-EAP or WPA2-EAP Select a wireless LAN compliant WPA-EAP or WPA2-EAP authentication and install a digital certificate on the projector. ❶ Set [DATE, TIME PRESET] on the projector. (See previous page) ❷ Use a computer to save digital certificates (files) for WPA-EAP or WPA2-EAP setting to your USB memory device. After completing saving the file, remove the USB memory device from the computer.
❼ Use the SELECT ▼▲ button to select [TKIP] or [AES] and press the ENTER button. Select [TKIP] or [AES] according to the setting for your access point. ❽ Use the SELECT ▲ button to select the [SECURITY] tab and press the SELECT ▶ button. The [AUTHENTICATION] page will be displayed. Select either [EAP-TLS] or [PEAP-MSCHAPv2] for [EAP TYPE]. The setting items vary depending on the EAP type. See the table below.
❿ Use the SELECT ▼ button to select [CLIENT CERTIFICATE] and press the ENTER button. A list of files (thumbnail screen) will be displayed. • For operating the thumbnail screen, see “5. Using the Viewer” in the “User’s Manual” (PDF). • To return to the [AUTHENTICATION] page, press the EXIT button. NOTE: Installing a digital certificate You can install each digital certificate (client certificate and CA certificate) for [PROFILE 1 (or 2)] on a file-by-file basis.
⓭ Use the SELECT ▼ button to select [CA CERTIFICATE] and press the ENTER button. A list of files (thumbnail screen) will be displayed. ⓮ On the thumbnail screen, select a digital certificate (DER format file) saved in your USB memory device and press the ENTER button. • Select your root CA certificate here. The selected digital certificate will be installed on the projector. ⓯ After completing required settings, use the SELECT ▼ button to select [OK] and press the ENTER button.
HINT: • The PKCS#12 format digital certificate including a CA certificate will be installed as a root CA certificate. ② Selecting [PEAP-MSCHAPv2] for [EAP TYPE]: ❾ From the [AUTHENTICATION] page, use the SELECT ▼ button to select [EAP TYPE] field and press the ENTER button. The pull-down list will be displayed. ❿ Use the SELECT ▼▲ button to select [PEAP-MSCHAPv2] and press the ENTER button. ⓫ Use the SELECT ▼ button to select [USER NAME] field and press the ENTER button.
⓭ After completing setting the password, use the SELECT ▼ button to select [CA CERTIFICATE] field and press the ENTER button. A list of files (thumbnail screen) will be displayed. • For operating the thumbnail screen, see “5. Using the Viewer” in the “User’s Manual” (PDF). • To return to the [AUTHENTICATION] page, press the EXIT button. NOTE: Installing a digital certificate You can install each digital certificate (client certificate and CA certificate) for [PROFILE 1 (or 2)] on a file-by-file basis.
⓱ Use the SELECT ▼ button to select [OK] and press the ENTER button. This will complete setting [PEAPMSCHAPv2] for [EAP TYPE] in [WPA-EAP] or [WPA2-EAP]. HINT: Clearing the digital certificate that is installed on the projector To clear the digital certificate installed on the projector, follow the steps below. By doing the following procedure, all the digital certificates for the currently displayed profile will be cleared.
4. Checking Authentication Status on [INFORMATION] Screen You can check your authentication status on the [INFORMATION] screen from the onscreen menu. ❶ Display the [INFORMATION] screen. • Use the first tab (main menu) to select [INFORMATION]. ❷ Select the [WIRELESS LAN(1)] tab. The current authentication status will be displayed in the [AUTHENTICATION] field. The meanings of these status statements are described below. Statement 16 Authentication status Authenticated Authentication is done correctly.
