User guide Nokia N93i-1
DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION, declares that this RM-156 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/ declaration_of_conformity/. The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of-life.
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW. YOU FURTHER ACKNOWLEDGE THAT NEITHER NOKIA NOR ITS AFFILIATES MAKE ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR THAT THE APPLICATIONS WILL NOT INFRINGE ANY THIRD-PARTY PATENTS, COPYRIGHTS, TRADEMARKS, OR OTHER RIGHTS.
Contents For your safety...........................................7 Get connected..........................................10 Nokia support and contact information....................... 23 Get started ............................................................................ 23 Additional applications ..................................................... 23 Your Nokia N93i......................................11 Camera......................................................24 Modes....................
Messaging................................................ 42 Write text ..............................................................................43 Write and send messages..................................................44 Inbox—receive messages ...................................................46 Mailbox...................................................................................48 View messages on a SIM card .........................................50 Messaging settings ......................
Device manager................................................................... 92 Modem .................................................................................. 93 Office ........................................................94 Recorder................................................................................. 94 Converter............................................................................... 94 Calculator.........................................................................
For your safety Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information. SWITCH OFF WHEN REFUELING Do not use the device at a refueling point. Do not use near fuel or chemicals. SWITCH ON SAFELY Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger. SWITCH OFF NEAR BLASTING Follow any restrictions. Do not use the device where blasting is in progress.
CONNECTING TO OTHER DEVICES When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products. EMERGENCY CALLS Ensure the phone function of the device is switched on and in service. The keypad is active only in the fold-open mode. Press the end key as many times as needed to clear the display and return to the standby mode. Enter the emergency number, then press the call key. Give your location.
them, you should take the same precautions, for security or content, as you would with any internet site. Network services To use the phone you must have service from a wireless service provider. Many of the features require special network features. These features are not be available on all networks; other networks may require that you make specific arrangements with your service provider before you can use the network services.
Get connected Get connected Use your device on the 2G and 3G networks. See ‘About your device’, p. 8. 2G and 3G Bluetooth WLAN USB and TV OUT memory card 10 Use Bluetooth technology to transfer files and connect to compatible enhancements, for example. See ‘Bluetooth connectivity’, p. 83. Use infrared to transfer and synchronize data between compatible devices, for example. See ‘Infrared connection’, p. 87. Use wireless LAN to connect to the internet and WLAN enabled devices. See ‘Wireless LAN’, p.
Model number: Nokia N93i-1 Hereinafter referred to as Nokia N93i. Modes Your device has four mechanical modes that are optimized for different uses: fold closed for carrying, fold open for traditional mobile phone use, imaging for recording video and taking pictures, and view for viewing your images and videos. To switch between the modes, turn the fold and the swing axis display. There is a short time-out before a mode is activated.
Your Nokia N93i 12 Incoming calls are indicated by their normal tone and a note. In the cover display settings, select Answer if fold opened to answer a call when you open the fold. If a compatible headset is connected to the device, press the answer key on the headset. To change the settings, see ‘Cover display’, p. 106. To make calls or use the menu, open the fold. To use the flash as a flashlight, press the flash key on the side of the device.
In the imaging mode, the numeric keypad is not active. You can use the capture key, zoom key, side scroll key, camera mode key, and flash key (all located on the side of the device), , and the landscape selection keys next to the main display. View mode When the fold is closed and you lift the side of the swing axis display, the view mode is activated. Use the view mode to do the following: • View your images. • Activate photos and movies from the gallery to watch slideshows.
Your Nokia N93i For other shortcuts available in the standby mode, see ‘Active standby mode’, p. 100. Edit text and lists • To mark an item in a list, scroll to it, and press and at the same time. • To mark multiple items in a list, press and hold while you press or . To end the selection, release or , then . • To select letters and words, press and hold . At the same time, press or to highlight text. To copy the text to clipboard, while still holding , select Copy.
Content is copied from the memory and compatible memory card (if inserted) of the other device to the corresponding location in your Nokia device and memory card (if inserted). The copying time depends on the amount of data to be transferred. You can cancel copying and continue later. To view the log information of a previous transfer, in the main view, select Transfer log. To view the devices you have copied or transferred data from, in the main view, select Phones.
Your Nokia N93i All calls to the device are forwarded to another number. If you have two phone lines (network service), the indicator for the first line is and for the second . A compatible headset is connected to the device. A compatible loopset is connected to the device. A USB connection is active. An infrared connection is active. If the indicator is blinking, the device is trying to connect to the other device or the connection has been lost. A compatible text phone is connected to the device.
To increase or decrease the volume level when you have an active call or are listening to a sound, press or . The built-in loudspeaker allows you to speak and listen from a short distance without having to hold the device to your ear. Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud. To use the loudspeaker during a call, select Options > Activate loudsp.. To turn off the loudspeaker, select Options > Activate handset.
Your Nokia N93i To add cities to the list, select Options > Add city. You can add a maximum of 15 cities to the list. To set your current city, scroll to a city, and select Options > My current city. The city is displayed in the clock main view, and the time in your device is changed according to the city selected. Check that the time is correct and matches your time zone. Headset Connect a compatible headset to the Pop-PortTM connector of your device.
Wireless LAN connections To use wireless LAN, you must create an internet access point (IAP) in a wireless LAN. Use the access point for applications that need to connect to the internet. See ‘Connection manager’, p. 91 and ‘WLAN wizard’, p. 81. Important: Always enable one of the available encryption methods to increase the security of your wireless LAN connection. Using encryption reduces the risk of unauthorized access to your data.
Your Nokia N93i home network, on the PC, you must install the Home Media Server software from the DVD-ROM supplied with your Nokia device. After you have completed the necessary configurations in all devices connected to the network, you can start using Home net. to share your media files. See ‘View media files’, p. 90. Insert the memory card 1 Place your finger in the upper corner of the door, and swing the door to the side.
To format a memory card, select Options > Format mem. card. Select Yes to confirm. select OK when prompted to confirm the removal. Important: Do not remove the memory card in the middle of an operation when the card is being accessed. Removing the card in the middle of an operation may damage the memory card as well as the device, and data stored on the card may be corrupted. Tip! For optimal performance, use your Nokia device to format all new miniSD cards.
Your Nokia N93i To find a file, select Options > Find and the memory from which to search, and enter a search text that matches the file name. View memory consumption To view what types of data you have in the device and how much memory the different data types consume, select Options > Memory details. The amount of available memory is shown in Free memory. Memory low—free memory The device notifies you if the device or the memory card memory is low.
Your device has context-sensitive help. When an application is open, select Options > Help to access help for the current view. When you are reading the instructions, to switch between help and the application that is open in the background, press and hold . To open help from the main menu, select Tools > Help. Select the desired application to view its help topics. Tutorial The tutorial gives you information about some of the features of your device.
Camera Camera Your Nokia device has two cameras, a high-resolution camera on the side of the device (the main camera) and a lower-resolution camera on the top of the main display (the secondary camera). You can use both cameras to take still images and record video in the portrait and landscape views. The Nokia device supports an image capture resolution of 2048x1536 pixels using the main camera. The image resolution in these materials may appear different.
After you record a video clip, select the following from the toolbar: • To immediately play the video clip you just recorded, select Play. • If you do not want to keep the video, select Delete. • To send the video using multimedia, e-mail, Bluetooth connectivity, or infrared, press , or select Options > Send. For more information, see ‘Messaging’, p. 42 and ‘Bluetooth connectivity’, p. 83. This option is not available during an active call. • To record a new video clip, select New video.
Camera a compatible TV or PC and handset), TV (normal), Handset (high), Handset (normal), or Sharing (limited video clip size to send using multimedia message (MMS)). If you want to view the video on a compatible TV or PC, select TV (high), which has VGA resolution (640x480) and the .mp4 file format. To send the video clip through MMS, select Sharing (QCIF resolution, .3gp file format).
Tip! Select Options > Turn icons on to display all viewfinder indicators or Turn icons off to display only the camera status indicators. When taking a picture, note the following: • The quality of a digitally zoomed picture is lower than that of a nonzoomed picture. • The camera goes into the battery saving mode if there are no keypresses for a moment. To continue taking pictures, press .
Camera Image quality—Print 3M - Large (2048x1536 resolution), Print 2M - Med. (1600x1200 resolution), Print 1.3M - Small (1280x960 resolution), or MMS 0.3M (640x480 resolution). The higher the resolution, the more memory the image consumes. If you want to print the image, select Print 3M - Large, Print 2M - Med., or Print 1.3M - Small. If you want to send it through e-mail, select Print 1.3M - Small. To send the image through MMS, select MMS 0.3M. These resolutions are only available in the main camera.
mode uses its own lighting settings that have been adjusted according to a certain kind of environment. You can also use the self-timer in the sequence mode. White balance—Select the current lighting condition from the list. This allows the camera to reproduce colors more accurately. Tip! Select Options > Self timer > 2 seconds to keep your hand steady when taking a picture. Flash Exposure value (images only)—Adjust the exposure time of the camera. The flash is available only in the main camera.
Camera each shooting mode have been set according to a certain style or environment. Shooting modes are only available in the main camera. Scroll through the toolbar, and select the video or image shooting modes. When you take pictures, the default shooting mode is Automatic. To make your own shooting mode suitable for a certain environment, select User > Options > Change. In the user defined shooting mode you can adjust different lighting and color settings.
To view, store, and organize your images, video clips, sound clips, playlists, and streaming links, or share your files with other compatible Universal Plug and Play (UPnP) devices through wireless LAN, press , and select Gallery. To open the gallery from the Camera application, select Options > Go to Gallery. From Camera, only Images & video is available. Tip! To switch from Gallery to the camera, in Images & video, press the capture key or the camera mode key, or select Options > Go to Camera.
Gallery The options related to Home net. are not available in Gallery before the settings for Home net. have been configured. To create custom video clips, select a video clip or several clips in the gallery, and Options > Edit. See ‘Edit video clips’, p. 32. View images and video clips To print your images on a compatible printer, or to store them on your memory card (if inserted) for printing, select Options > Print. See ‘Image print’, p. 40.
You can also use Movie director to create custom video clips. Select the video clips and images you want to create a muvee with and select Options > Edit > Create muvee. See ‘Movie director’, p. 78. In the video editor you can see two timelines: video clip timeline and sound clip timeline. The images, text, and transitions added to a video clip are shown on the video clip timeline. To switch between the timelines, scroll up or down.
Gallery To send the video, select Send > Via multimedia, Via e-mail, Via Bluetooth, or Via infrared. Contact your service provider for details of the maximum multimedia message size that you can send. Tip! If you want to send a video clip that is over the maximum multimedia message size allowed by your service provider, you can send the clip using Bluetooth wireless technology. See ‘Send data’, p. 85.
TV screen displays what is displayed on the screen of your device. Pause—to pause the slide show When you open an image in the thumbnail view while it is viewed on the TV, the Zoom in option is not available. When image is not zoomed, the opened image is displayed on the TV in full screen. Continue—to resume the slide show, if paused End—to close the slide show To browse the images, press (previous) or (next).
Gallery select Presentations, scroll to an image, and select Options > Play. To zoom in, press . To zoom out, press . To switch between full screen and normal screen, press *. Albums With albums you can conveniently manage your images and video clips. To view the albums list, in Images & video, select Options > Albums > View albums. To add a picture or a video clip to an album in the gallery, scroll to a picture or video clip, and select Options > Albums > Add to album. A list of albums opens.
Music player Press , and select Music player. With the music player, you can play music files and create and listen to playlists. Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing. Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud. Add music Play music When you open the music player, the previously played track or playlist is displayed.
Media applications stops at the end of the playlist or restarts from its beginning, select Options > Loop. To open your web bookmarks for downloading music, select Options > Track downloads. To return to the standby mode and leave the music playing in the background, select Options > Play in background. Music library To view the music library, select Options > Music library. All tracks lists all music. To view sorted songs, select Albums, Artists, Genres, or Composers.
To change the default USB connection mode, press select Connect. > Data cbl.. , Both Windows Media Player and Nokia Music Manager in Nokia PC Suite have been optimized for transferring music files. For information about transferring music with Nokia Music Manager, see the Nokia PC Suite user guide. Music transfer with Windows Media Player The functionality of the music synchronization may vary between different versions of the Windows Media Player application.
Media applications The playlists on your device are not synchronized with the Windows Media Player playlists. If the default printer is not available, a list of available printing devices is displayed. Image print To change the default printer, select Options > Settings > Default printer. Use Image print to print your images using a compatible data cable, wireless LAN (if available), Bluetooth connectivity, or a compatible memory card (if available). You can only print images that are in .jpeg format.
To transfer and back up media files from your device to a compatible PC through the wireless LAN, select Options > Transfer > Start. See ‘Wireless LAN’, p. 18. Your device starts a device search. Select a device and a folder to which you want to transfer the media files. Select OK. To change the settings for Storage device or Storage folder, select Options > Settings.
Messaging Messaging Press , and select Messag.. In Messaging, you can create, send, receive, view, edit, and organize text messages, multimedia messages, e-mail messages, and special text messages containing data. You can also receive messages and data using Bluetooth connectivity or infrared, receive web service messages, cell broadcast messages, and send service commands. To create a new message, select New message. Only devices that have compatible features can receive and display multimedia messages.
Cell broadcast (network service) allows you to receive messages on various topics, such as weather or traffic conditions from your service provider. For available topics and relevant topic numbers, contact your service provider. In the main view of Messaging, select Options > Cell broadcast. In the main view, you can see the status of a topic, a topic number, name, and whether it has been flagged ( ) for follow-up. Cell broadcast messages cannot be received in UMTS networks.
Messaging If the word is not correct, press repeatedly to view the matching words the dictionary has found one by one, or press , and select Predictive text > Matches. If the ? character is shown after the word, the word is not in the dictionary. To add a word to the dictionary, select Spell, enter the word using traditional text input, and select OK. The word is added to the dictionary. When the dictionary is full, a new word replaces the oldest added word. 4 Start writing the next word.
2 3 4 5 To change the format in which recorded videos are saved, see ‘Video settings’, p. 25. 6 To take a new picture or record sound or video for a multimedia message, select Insert new > Image, Sound clip, or Video clip. To insert a new slide to the message, select Slide. To see what the multimedia message looks like, select Options > Preview. 7 To add an attachment to an e-mail, select Options > Insert > Image, Sound clip, Video clip, or Note. E-mail attachments are indicated by .
Messaging language options, take up more space, limiting the number of characters that can be sent in a single message. point you create as the preferred connection. See also ‘Multimedia messages’, p. 51. E-mail messages are automatically placed in Outbox before sending. If sending does not succeed, the e-mail is left in the Outbox with the Failed status. Before you can send, receive, retrieve, reply to, and forward e-mail, you must do the following: • Configure an IAP correctly. See ‘Connection’, p.
Multimedia messages Important: Exercise caution when opening messages. Multimedia message objects may contain malicious software or otherwise be harmful to your device or PC. You may receive a notification that a multimedia message is waiting in the multimedia message center. To start a packet data connection to retrieve the message to your device, select Options > Retrieve. When you open a multimedia message ( ), you may see an image and a message. is shown if sound is included, or if video is included.
Messaging Web service messages Web service messages ( ) are notifications (for example, news headlines) and may contain a text message or a link. For availability and subscription, contact your service provider. Mailbox If you select Mailbox and have not set up your e-mail account, you are prompted to do so. To start creating the e-mail settings with the mailbox guide, select Start. See also ‘E-mail’, p. 52.
To view e-mail attachments, open a message that has the attachment indicator , and select Options > Attachments. If the attachment has a dimmed indicator, it has not been retrieved to the device; select Options > Retrieve. You can also receive meeting requests in the mailbox. See ‘Meeting requests’, p. 72, and ‘Create calendar entries’, p. 72.
Messaging To cancel deleting an e-mail from the device and server, scroll to an e-mail that has been marked to be deleted during the next connection ( ), and select Options > Restore. Disconnect from the mailbox When you are online, to end the data connection to the remote mailbox, select Options > Disconnect. View messages on a SIM card Before you can view SIM messages, you must copy them to a folder in your device. 1 In the Messag. main view, select Options > SIM messages.
Multimedia messages Press , and select Messag. > Options > Settings > Multimedia message and from the following: Image size—Define the size of the image in a multimedia message: Original (shown only when the MMS creation mode is set to Guided or Free), Small, or Large. MMS creation mode —If you select Guided, the device informs you if you try to send a message that may not be supported by the recipient. Select Restricted; the device prevents you from sending messages that may not be supported.
Messaging E-mail Press , and select Messag. > Options > Settings > E-mail and from the following: Mailboxes—Select a mailbox to change the following settings: Connection settings, User settings, Retrieval settings, and Automatic retrieval. Mailbox in use— Select which mailbox you want to use for sending e-mail. To create a new mailbox, select Options > New mailbox in the mailbox main view.
User settings My name—Enter your own name. Your name replaces your e-mail address in the recipient’s device when the recipient’s device supports this function. Retrieval settings E-mail to retrieve—Define which parts of the e-mail are retrieved: Headers only, Size limit (for POP3 only), or Msgs. & attachs. (for POP3 only). Retrieval amount—Define how many new e-mail messages are retrieved to the mailbox. Send message—Define how e-mail is sent from your device.
Messaging automatically activate the browser and start a network connection to retrieve content when you receive a service message, select Download messages > Automatically. Cell broadcast Check the available topics and related topic numbers with your service provider. Press , and select Messag. > Options > Settings > Cell broadcast and from the following: Reception—Select whether you want to receive cell broadcast messages.
Press , and select Contacts. In Contacts you can add a personal ringing tone or a thumbnail image to a contact card. You can also create contact groups, which allow you to send text messages or e-mail to many recipients at the same time. You can add received contact information (business cards) to contacts. See ‘Data and settings’, p. 47. Contact information can only be sent to or received from compatible devices. Save names and numbers 1 Select Options > New contact.
Contacts (phonebook) Default numbers and addresses You can assign default numbers or addresses to a contact card. In this way if a contact has several numbers or addresses, you can easily call or send a message to the contact to a certain number or address. The default number is also used in voice dialing. 1 In the address book, select a contact, and press . 2 Select Options > Defaults. 3 Select a default to which you want to add a number or an address, and select Assign.
5 Scroll to a contact, and press Add ringing tones for contacts To rename a group, select Options > Rename, enter the new name, and select OK. When a contact or group member calls you, the device plays the chosen ringing tone (if the caller’s telephone number is sent with the call and your device recognizes it). 1 Press to open a contact card or go to the groups list, and select a contact group. 2 Select Options > Ringing tone. A list of ringing tones opens.
Make calls Make calls Voice calls Tip! To increase or decrease the volume during a call, press or . You can make voice calls in the fold-open mode and view mode. See ‘Modes’, p. 11. 1 To start a voice call, with the fold open, enter the phone number in the standby mode, including the area code. To remove a number, press .
Speed dial a phone number To activate speed dialing, press , and select Tools > Settings > Call > Speed dialling > On. To assign a phone number to one of the speed dialing keys ( — ), press , and select Tools > Spd. dial. Scroll to the key to which you want to assign the phone number, and select Options > Assign. is reserved for the voice mailbox. To call in the standby mode, press the speed dial key and . Voice dialing Your device supports enhanced voice commands.
Make calls 2 A short tone is played, and Speak now is displayed. Say clearly the name or nickname that is saved on the contact card. 3 The device plays a synthesized voice tag for the recognized contact in the selected device language, and displays the name and number. After a timeout of 2.5 seconds, the device dials the number. If the recognized contact was not correct, select Next to view a list of other matches, or Quit to cancel voice dialing.
Tip! To increase or decrease the volume during a call, press or . To change between showing video or hearing only sound, select Enable or Disable > Sending video, Sending audio, or Sending audio & video. To zoom your own image, select Zoom in or Zoom out. The zoom indicator is shown on the top of the display. To switch the places of the sent and received video images on the display, select Change image order.
Make calls Settings Person-to-person connection settings A person-to-person connection is also known as a session initiation protocol (SIP) connection. The SIP profile settings must be configured in your device before you can use Video sharing. Setting up a SIP profile allows you to establish a live person-to-person connection to another compatible phone. The SIP profile must also be established to receive a sharing session.
Video clip 1 When a voice call is active, select Options > Share video > Clip. A list of video clips opens. 2 Select a video clip you want to share. A preview view opens. To preview the clip, select Options > Play. 3 Select Options > Invite. You may need to convert the video clip into a suitable format to be able to share it. Clip must be converted for sharing. Continue? appears. Select OK. The device sends the invitation to the SIP address you have added to the contact card of the recipient.
Make calls Answer or reject a call Answer or reject a video call To answer the call in the fold-open mode, press . If Answer if fold opened is set to Yes, to answer a call in the fold-closed mode, open the fold, and the call starts automatically. Otherwise, open the fold, and press . When a video call arrives, To mute the ringing tone when a call comes in, select Silence. To mute the ringing tone in the fold-closed mode, press the side scroll key.
You can answer a call while you have another call in progress if you have activated Call waiting (network service) in Tools > Settings > Call > Call waiting. To answer the waiting call, press on hold. . The first call is put To switch between the two calls, select Swap. Select Options > Transfer to connect an incoming call or a call on hold with an active call and to disconnect yourself from the calls. To end the active call, press . To end both calls, select Options > End all calls.
Make calls calls only if the network supports these functions, the device is switched on, and within the network service area. Tip! When you see a note in the standby mode about missed calls, select Show to access the list of missed calls. To call back, scroll to a name or number, and press . To clear all recent call lists, select Options > Clear recent calls in the recent calls main view. To clear one of the call registers, open the register you want to erase, and select Options > Clear list.
Tip! To see the duration of a voice call on the main display during an active call, select Options > Settings > Show call duration > Yes. Tip! To view a list of sent messages, press select Messag. > Sent. , and Subevents, such as a text message sent in more than one part and packet data connections, are logged as one communication event. Connections to your mailbox, multimedia messaging center, or web pages are shown as packet data connections.
Services Services Various service providers maintain pages specifically designed for mobile devices. These pages use the wireless markup language (WML), extensible hypertext markup language (XHTML), or hypertext markup language (HTML). Check the availability of services, pricing, and fees with your service provider. Service providers will also give you instructions on how to use their services. Press , and select Services. Shortcut: To start a connection, press and hold in the standby mode.
If the security indicator is displayed during a connection, the data transmission between the device and the internet gateway or server is encrypted. The security icon does not indicate that the data transmission between the gateway and the content server (or place where the requested resource is stored) is secure. The service provider secures the data transmission between the gateway and the content server.
Services To open a sublist of commands or actions for the currently open page, select Options > Service options. You can download files that cannot be shown on the browser page, such as ringing tones, images, operator logos, themes, and video clips. To download an item, scroll to the link, and press . When you start a download, a list of ongoing, paused, and completed downloads from the current browsing session is displayed. To view the list, select Options > Tools > Downloads.
Select Options > Settings and from the following: Access point—Change the default access point. See ‘Connection’, p. 107. Some or all access points may be preset for your device by your service provider, and you may not be able to change, create, edit, or remove them. Homepage—Define the home page. Load imgs. & sounds—Select whether you want to load images while browsing. If you select No, to load images later during browsing, select Options > Show images. Font size—Select the text size.
Calendar Calendar Use Calendar to remind you of meetings, anniversaries, and to keep track of your tasks and other notes. Create calendar entries Shortcut: In the day, week, or month calendar view, press any key ( — ). An appointment entry opens, and the characters you enter are added to the Subject field. In the to-do view, a to-do note entry opens.
Manage your calendar entries Calendar views To delete more than one event at a time, go to the month view, and select Options > Delete entry > Before date or All entries. Tip! Select Options > Settings to change the starting day of the week or the view that is shown when you open the calendar. In the month view, dates that have calendar entries are marked with a small triangle in the bottom right corner. In the week view, memos and anniversaries are placed before 8 a.m.
Applications Applications Visual Radio You can use the Visual Radio application (network service) as a traditional FM radio with automatic tuning and saved stations. If you tune to stations that offer Visual Radio service, you can view visual information on the display related to the radio program. The Visual Radio service uses packet data (network service). You can listen to the FM radio while using other applications.
Listen to the radio Note that the quality of the radio broadcast depends on the coverage of the radio station in that particular area. Connect a compatible headset to the device. The lead of the headset functions as the radio antenna, so let it hang freely. Press , and select Applications > Radio. To start a station search, select or . Searching stops when a station is found. To change the frequency manually, select Options > Manual tuning.
Applications To adjust display settings for the visual content view, select Options > Display settings > Lighting or Power saver time-out. Saved stations You can save up to 20 radio stations in Visual Radio. To open your station list, select Options > Stations. To listen to a saved station, select Options > Station > Listen. To view available visual content for a station with Visual Radio service, select Options > Station > Start visual service. To change station details, select Options > Station > Edit.
begins streaming, your device connects to the site and starts loading the content. The content is not saved in your device. Tip! To view a video clip in full screen mode, press . Press again to change back to normal screen mode. Receive RealPlayer settings Shortcuts during play are as follows: • To fast forward, press and hold . • To rewind through the media file, press and hold . • To mute the sound, press and hold until is displayed. To turn on the sound, press and hold until you see .
Applications access to browser pages that contain sound or video clips. Netw. sett.— • Default access point—Scroll to the access point you want to use to connect to the internet, and press . • Online time—Set the time for RealPlayer to disconnect from the network when you pause a media clip playing through a network link. Select User defined, and press . Enter the time, and select OK. • Lowest UDP port—Enter the lowest port number of the server’s port range. The minimum value is 1024.
Create a custom muvee 1 In the Movie director main view, select the videos and images with which you want to create a muvee, and select Options > Create muvee; or select Images & video in Gallery. Select the videos and images with which you want to create a muvee, and select Options > Edit > Create muvee. 2 Select a style for the muvee from the style list.
Internet Internet Web Press , and select Internet > Web (network service). Various service providers maintain pages specifically designed for mobile devices. These pages use the wireless markup language (WML), extensible hypertext markup language (XHTML), or hypertext markup language (HTML). Web feeds are xml files in web pages that are widely used by the weblog community to share the latest entries' headlines or their full text, for example, recent news.
To zoom the page in or out, press or again . To allow or prevent the automatic opening of multiple windows, select Options > Settings > Block pop-ups > Yes. To view the web pages you have visited during the current browsing session, select Options > Navigation options > History. To have the list of the previous pages automatically shown when you return to the previous page, select Options > Settings > History list > On.
Internet If you are connected to a wireless LAN, the IAP name is displayed. To start the web browser using this IAP, select the status and the option Continue Web browsing. To end the connection in the wireless LAN, select the status and the option Disconnect WLAN. If wireless LAN scanning is off and you are not connected to any wireless LAN, WLAN scanning off is displayed. To set scanning on and search for available wireless LANs, select the status WLAN scanning off.
PC connections You need to connect your device to a compatible PC to do the following: • Transfer information between Nokia PC Suite applications and your device. For example, to synchronize calendar appointments or transfer images. • Use your device as a modem to connect to network services such as the internet. You can connect your device and a compatible PC via a compatible USB or serial cable, infrared, or Bluetooth wireless technology.
Connectivity need to be within 10 meters (33 feet) of each other, but the connection may be subject to interference from obstructions such as walls or from other electronic devices. This device is compliant with Bluetooth Specification 2.
Security tips To use the remote SIM mode with a compatible car kit enhancement, set Bluetooth connectivity on, and enable the use of the remote SIM mode with your device. Before the mode can be activated, the two devices must be paired and the pairing initiated from the other device. When pairing, use a 16-digit passcode, and set the other device as authorized. See ‘Pair devices’, p. 86. Activate the remote SIM mode from the other device.
Connectivity 2 Select the item and Options > Send > Via Bluetooth. Devices with Bluetooth technology within range start to appear on the display. Device icons are: computer, phone, audio or video device, and other device. To interrupt the search, select Stop. 3 Select the device with which you want to connect. 4 If the other device requires pairing before data can be transmitted, a tone sounds, and you are asked to enter a passcode. See ‘Pair devices’, p. 86.
When you receive data through Bluetooth connectivity, a tone sounds, and you are asked if you want to accept the message. If you accept, is shown, and the item is placed in Inbox in Messag.. Messages received through Bluetooth connectivity are indicated by . See ‘Inbox— receive messages’, p. 46. Switch off To switch off Bluetooth connectivity, select Bluetooth > Off. Infrared connection With infrared, you can transfer data such as business cards, calendar notes, and media files with a compatible device.
Connectivity Home network Your device is compatible with UPnP. Using a wireless LAN access point device or a wireless LAN router, you can create a home network and connect compatible UPnP devices that support wireless LAN to the network, such as your Nokia device, a compatible PC, a compatible printer, and a compatible sound system or a TV, or a sound system or TV equipped with a compatible wireless multimedia receiver.
The options related to Home net. are not available in Gallery before the settings for Home net. have been configured. If you use wireless LAN in a network that does not have encryption, switch off sharing files with other devices, or do not share any private media files. To change sharing settings, see ‘Home network settings’, p. 89.
Connectivity the home network can view and copy your files you have selected for sharing in Images & video and Music. To select media files for sharing with other devices from Images & video and Music or to view their sharing status, select Share content. View media files To connect a compatible PC to the home network, you must install the Home Media Server software from the DVD-ROM supplied with your Nokia device.
compatibility, contact the supplier of the application with which you want to synchronize your device data. Copy media files You may receive synchronization settings in a special text message. See ‘Data and settings’, p. 47. To copy or transfer media files from your device to another compatible device, such as a UPnP compatible PC, select a file in Gallery and Options > Move and copy > Copy to home network or Move to home network. Content sharing does not have to be switched on.
Connectivity Data connections In the active connections view, you can see the open data connections: data calls ( ), packet data connections ( or ), and wireless LAN connections ( ). Note: The actual time invoiced for calls by your service provider may vary, depending on network features, rounding off for billing, and so forth. To end a connection, select Options > Disconnect. To close all open connections, select Options > Disconnect all. To view the details of a connection, select Options > Details.
Session mode—Select the connection type that is used to connect to the server: Internet or Bluetooth. Access point—Select an access point to be used when connecting to the server. modem, press . For how to connect the devices, see ‘Infrared connection’, p. 87. Connectivity Server password—Enter a password to identify your device to the server. Host address—Enter the URL address of the server. Port—Enter the port number of the server. User name and Password—Enter your user name and password.
Office Office Recorder Base currency and exchange rates Select Type > Currency > Options > Currency rates. Before you can make currency conversions, you must select a base currency and add exchange rates. The rate of the base currency is always 1. To record voice memos, press , and select Office > Recorder. To record a telephone conversation, open Recorder during a voice call. Both parties hear a tone every 5 seconds during recording.
Use the Zip manager application to compress files. Compressed files use less memory and are more convenient to send to compatible devices. To open the application, press , and select Office > Zip. To create or manage archives or to change the settings, select Options and the desired option. You can store archive files on the device or on a compatible memory card. Quickoffice With Quickoffice, you can view .doc, .xls, .ppt, and .txt documents. All file formats or features are not supported.
Office Quickpoint With Quickpoint, you view Microsoft PowerPoint presentations with your device. Quickpoint supports the viewing of presentations created in .ppt format created with Microsoft PowerPoint 2000 and XP. Not all variations or features of the mentioned file formats are supported. To open a presentation, press , and select Office > Quickoffice > Quickpoint and the presentation. See also ‘More information’, p. 96.
To save the scanned data, select Options > Save. The data is saved in .bcr format. The device reverts to the standby mode to save battery power if Barcode cannot be activated or if no keys are pressed for 1 minute. To continue scanning or viewing saved information, press . Office To scan a code, select Scan code. Set the code between the red lines on the display. The Barcode attempts to scan and decode the code, and the decoded information is displayed.
Personalize your device 98 Personalize your device Your service provider may have requested that certain features be disabled or not activated in your device. If so, they do not appear on your device menu. Your device may also have been specially configured for your service provider. This configuration may include changes in menu names, menu order, and icons. Contact your service provider for more information. The images in this guide may differ from your device display.
When the offline profile is active, you can use your device without a (U)SIM card. To modify a profile, press , and select Tools > Profiles. Scroll to the profile, and select Options > Personalise. Scroll to the setting you want to change, and press to open the choices. Tones stored on the memory card are indicated with . You can scroll through the tone list and listen to each one before you make your selection. To stop the sound, press any key.
Personalize your device Change the look of your device To change the look of the display, such as the wallpaper and icons, press , and select Tools > Themes. The active theme is indicated by . In Themes you can group together elements from other themes or select images from the Gallery to personalize themes further. The themes on a compatible memory card (if inserted) are indicated by . The themes on the memory card are not available if the memory card is not inserted in the device.
Multimedia key To open the default shortcut assigned to the multimedia key, press and hold . To open a list of multimedia applications, press . To open the desired application, use the scroll key. To exit the list without selecting an application, press . To change the shortcuts, press and . To change the applications that are shown when you press , select Top, Left, Middle, and Right and the application. Some shortcuts may be fixed, and you are not able to change them.
Tools recognized voice tags and commands in the selected device language, select Synthesiser > Off. To reset voice recognition learning (for example, when the main user of the device has changed), select Reset voice adapts.. Application manager Press , and select Tools > App. mgr.. You can install two types of applications and software to your device: • J2ME™ applications based on Java technology with the extension .jad or .jar ( ).
To start an installed application, locate it in the menu, and press . To start a network connection and to view extra information about the application, select Options > Go to web address, if available. To see what software packages are installed or removed and when, select Options > View log. To send your installation log to a help desk so that they can see what is installed or removed, select Options > Send log > Via text message or Via e-mail (available only if the correct e-mail settings are in place).
Tools may stop working. Refer to the documentation of the installed software package for details. Settings Select Options > Settings and from the following: Online certif. check—Select to check the online certificates before installing an application. Default web address—Set the default address used when checking online certificates. Some Java applications may require a phone call, a message to be sent, or a network connection to a specific access point for downloading extra data or components.
To change settings, press , and select Tools > Settings. To open a settings group, press . Scroll to a setting you want to change, and press . Writing language—Changing the language affects the characters and special characters available when writing text and the predictive text dictionary used. Some settings may be preset for the device by your service provider, and you may not be able to change them. Predictive text—Set the predictive text input On or Off for all editors in the device.
Settings Right selection key—Assign a shortcut to the right selection key ( ) in the standby mode. Active standby apps.—Select the application shortcuts you want to appear in the active standby. This setting is only available if Active standby is on. You can also assign keypad shortcuts for the different presses of the center selection key. The center selection key shortcuts are not available if the active standby is on. LED light—Select a color for the cover indicator.
Call waiting—If you have activated call waiting (network service), the network notifies you of a new incoming call while you have a call in progress. To check whether the function is active, select Check status. To set the function on or off, select Activate or Cancel. Reject call with SMS—Select Yes to send a text message to a caller informing why you could not answer the call. See ‘Answer or reject a call’, p. 64. Message text—Write text to be sent in a text message when you reject a call.
Settings be active at the same time, and access points can share a data connection. a You can also use a wireless LAN data connection. See ‘Wireless LAN’, p. 18. Only one connection in one wireless LAN can be active at a time. Tip! To create an IAP in a wireless LAN, press , and select Connect. > Conn. mgr. > Availab. WLAN > Options > Define access point. To establish a data connection, an access point is required.
Proxy port number—Enter the proxy port number. Prompt password—If you must enter the password every time you log in to a server, or if you do not want to save your password in the device, select Yes. Follow the instructions from your service provider. Password—A password may be needed to make a data connection, and is usually provided by the service provider. Authentication—Select Normal or Secure.
Settings WEP key settings—Enter WEP encryption (length of the key), WEP key format (ASCII or Hexadecimal), and WEP key (the WEP key data in the selected format). Security settings for 802.1x and WPA/WPA2 are as follows: WPA mode—Select the means of authentication: EAP to use an extensible authentication protocol (EAP) plug-in or Pre-shared key to use a password. Complete the appropriate settings: EAP plug-in settings (only for EAP)—Enter the settings as your service provider instructs.
To view advanced settings, select Options > Advanced settings. Changing wireless LAN advanced settings is not recommended. Configurations You may receive trusted server settings from your service provider in a configuration message, or the settings may be stored on your USIM card. You can save these settings to your device, view, or delete them in Configs.. Date and time See ‘Clock settings’, p. 17 and language settings in ‘General’, p. 105.
Settings Lock if SIM changed—You can set the device to ask for the lock code when an unknown SIM card is inserted into your device. The device maintains a list of SIM cards that are recognized as the owner’s cards. Closed user group—You can specify a group of people to whom you can call and who can call you (network service). When calls are limited to closed user groups, calls may be possible to the official emergency number programmed into your device.
To check certificate details, scroll to a certificate, and select Options > Certificate details. When you open certificate details, the validity of the certificate is checked, and one of the following notes may be displayed: Important: Even if the use of certificates makes the risks involved in remote connections and software installation considerably smaller, they must be used correctly in order to benefit from increased security.
Settings Internet > Yes—The certificate is able to certify servers. App. installation > Yes—The certificate is able to certify the origin of a new Java application. Select Options > Edit trust setting to change the value. Track protected object Some copyright-protected music files may include a transaction identifier. Select whether you allow the identifier to be sent with the music file if you send or forward the file.
Your device can automatically switch between the GSM and UMTS networks. The GSM network is indicated with in the standby mode. The UMTS network is indicated with . Network mode (shown only if supported by the operator)—Select which network to use. If you select Dual mode, the device uses the GSM or UMTS network automatically, according to the network parameters and the roaming agreements between the wireless service providers. Contact your network operator for more details.
Troubleshooting Troubleshooting Q&A Access codes Q: What is my password for the lock, PIN, or PUK codes? Q: Why can’t I end a Bluetooth connection? A: The default lock code is 12345. If you forget or lose the lock code, contact your device dealer. If you forget or lose a PIN or PUK code, or if you have not received such a code, contact your network service provider.
Log by lens movement when recording. Q: Why does the log appear empty? Q: Why do images or videos captured using night mode tend to be noisier under dark lighting conditions compared to normal mode? A: The output of the image sensor under the dark lighting conditions is more amplified with night mode than with normal mode to provide better brightness. In return, the noise level on the image or video increases.
Troubleshooting • Send images to your e-mail address, then save the images to your computer. • Send data using Bluetooth connectivity to a compatible device. • Store data on a compatible memory card. Messaging Q: Why can’t I select a contact? A: The contact card does not have a phone number or an e-mail address. Add the missing information to the contact card in Contacts.
Q: Why can't I see a wireless LAN (WLAN) access point even though I know I'm within its range? A: The WLAN access point may use a hidden service set identifier (SSID). You can only access networks that use a hidden SSID if you know the correct SSID and have created a WLAN IAP for the network on your Nokia device. Q: How do I switch wireless LAN (WLAN) off on my Nokia device? Troubleshooting Wireless LAN A: You cannot switch off WLAN on your Nokia device.
Battery information Battery information Charging and discharging Your device is powered by a rechargeable battery. The battery can be charged and discharged hundreds of times, but it will eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery. Use only Nokia approved batteries, and recharge your battery only with Nokia approved chargers designated for this device.
Successful completion of the four steps is not a total assurance of the authenticity of the battery. If you have any reason to believe that your battery is not an authentic, original Nokia battery, you should refrain from using it, and take it to the nearest authorized Nokia service point or dealer for assistance. Your authorized Nokia service point or dealer will inspect the battery for authenticity. If authenticity cannot be verified, return the battery to the place of purchase.
Battery information 122 What if your battery is not authentic? If you cannot confirm that your Nokia battery with the hologram on the label is an authentic Nokia battery, please do not use the battery. Take it to the nearest authorized Nokia service point or dealer for assistance. The use of a battery that is not approved by the manufacturer may be dangerous and may result in poor performance and damage to your device and its enhancements.
Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will help you protect your warranty coverage. • Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing it. • Do not use or store the device in dusty, dirty areas.
Additional safety information Additional safety information Your device and its enhancements may contain small parts. Keep them out of the reach of small children. Operating environment Remember to follow any special regulations in force in any area, and always switch off your device when its use is prohibited or when it may cause interference or danger. Use the device only in its normal operating positions.
Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider. Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more information, check with the manufacturer, or its representative of your vehicle, or any equipment that has been added.
Additional safety information To make an emergency call: 1 If the device is not on, switch it on. Check for adequate signal strength. Some networks may require that a valid SIM card is properly inserted in the device. 2 Press the end key as many times as needed to clear the display and ready the device for calls. 3 Enter the official emergency number for your present location. Emergency numbers vary by location. 4 Press the call key.
Index A access points 107, 108 activation keys 104 additional applications 23 Adobe reader 96 alarm clock 17 applications 102 B backing up 21 Bluetooth 83 device address 86 headset 115 pairing 86 security 85 switching off 87 bookmarks 68 C cache, clearing 70 calendar 72 call register. See log.
F file formats .jad, .jar, and .sis 102 RealPlayer 76 file manager 21 fixed dialing 56 FM radio 74 G gallery 31 backup files 41 ordering files in albums 36 presentations 35 TV out mode 35 H handsfree. See loudspeaker. headset settings 115 help application 23 home network 19 I IAP. See access points. indicators 15 internet. See web.
call barring 114 call diverting 114 certificates 112 data connections 107 date and time 111 display 106 language 105 lock code 112 original settings 105 personalizing the device 98 PIN code 112 screen saver 106 UPIN code 112 UPUK code 112 shortcuts 13 SIM card copying names and numbers 56 messages 50 sis file 102 snooze 17 software 102 songs transferring 38 sound clips 31 sounds muting a ringing tone 64 recording sounds 94 speed dialing 59 standby mode 98 support information 23 svg files 35 synchronization