Nokia Customer Care Service Manual RM-10;RM-24 (Nokia E70) Mobile Terminal Part No: 9246101 (Issue 1) COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Amendment Record Sheet Nokia Customer Care Amendment Record Sheet Amendment No Issue 1 Page ii Date 05/2006 Inserted By Comments TSa COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Copyright Nokia Customer Care Copyright Copyright © 2006 Nokia. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia, Nokia Connecting People, and Nokia X and Y are trademarks or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.
RM-10;RM-24 Warnings and cautions Nokia Customer Care Warnings and cautions Warnings • IF THE DEVICE CAN BE INSTALLED IN A VEHICLE, CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND ANTI-SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE DEALER/ MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY.
RM-10;RM-24 ESD protection Nokia Customer Care ESD protection Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use. To replace the covers ESD protection must be applied. All electronic parts of the product are susceptible to ESD.
RM-10;RM-24 Care and maintenance Nokia Customer Care Care and maintenance This product is of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. • Keep the phone and all its parts and accessories out of the reach of small children. • Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits.
RM-10;RM-24 Company Policy Nokia Customer Care Company Policy Our policy is of continuous development; details of all technical modifications will be included with service bulletins. While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing/email.
RM-10;RM-24 Battery information Nokia Customer Care Battery information Note: A new battery's full performance is achieved only after two or three complete charge and discharge cycles! The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.
RM-10;RM-24 Nokia E70 Service Manual Structure Nokia Customer Care Nokia E70 Service Manual Structure 1 General Information 2 Parts Lists and Component Layouts 3 Service Software Instructions 4 Service Tools and Service Concepts 5 Disassembly/Reassembly Instructions 6 BB Troubleshooting and Manual Tuning Guide 7 RF Troubleshooting and Manual Tuning Guide 8 Camera Module Troubleshooting 9 System Module 10 Schematics Glossary Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Nokia E70 Service Manual Structure Nokia Customer Care (This page left intentionally blank.) Page x COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care 1 — General Information Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 General Information Nokia Customer Care (This page left intentionally blank.) Page 1 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 General Information Nokia Customer Care Table of Contents RM-10/24 product selection..................................................................................................................................1–5 RM-10/24 product features and sales package...................................................................................................1–5 Product and module list...............................................................................................................
RM-10;RM-24 General Information Nokia Customer Care (This page left intentionally blank.) Page 1 –4 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 General Information Nokia Customer Care RM-10/24 product selection Nokia RM-10/24 is a triple band EGSM 900/1800/1900 phone, supporting WCDMA (3GPP Release 4). According to GSM standard 05.05 it responds to class 4 (max. 2W) in EGSM 900, class 1 (1W) in GSM 1800 and class 1 in GSM 1900. RM-10/24 supports EGPRS (EDGE) class B as well as Bluetooth 1.2 standard. The handset has a full phase 2 Type Approval and it complies with the GSM Type Approval.
RM-10;RM-24 General Information Nokia Customer Care • GSM Triband World Phone E900/1800/1900 EGPRS (class B, Multislot class 10) (Max DL=236.8 kbps UL=118.4 kbps ) Software platform • SW platform: Nokia Series 60 3.0 Connectivity • Integrated WLAN (IEEE 802.11g,WPA2) • USB 2.0 full-speed • Bluetooth 1.
RM-10;RM-24 General Information Nokia Customer Care Product and module list Module name Type code Notes System/RF Module 1EM Main PWB with components Flip module 1FF Flip PWB with components. Part of the flip assy.
RM-10;RM-24 General Information Nokia Customer Care Parameter Unit Channel spacing 200 kHz Number of Tx power levels GSM900: 15 GSM1800: 16 GSM1900: 16 Battery endurance Battery Capacity (mAh) BL-6C 1150 Talk time Stand-by • up to 3.6-7.3 hrs (GSM) • up to 2.5-3.9 hrs (WCDMA) • up to 4.3-6 hours* (VoIP) • 7.2 - 9.3 days (GSM) • 7.0 - 9.2 days (WCDMA) • 5.1 - 6.2 days* (GSM/ WCDMA and WLAN) Operation times may vary depending on radio access technology, network and usage.
Nokia Customer Care 2 — Parts Lists and Component Layouts Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care (This page left intentionally blank.) Page 2 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Table of Contents Exploded view.........................................................................................................................................................2–5 Exploded view....................................................................................................................................................2–5 Parts lists................................................................................
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care (This page left intentionally blank.) Page 2 –4 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Exploded view Exploded view Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Parts lists RM-10 mechanical spare parts list • Bold = assembly (assy) • I0xx = ITEM codes for upper or mono block • I1xx = ITEM codes for hinge block • I2xx = ITEM codes for lower block • I3xx = ITEM codes for soldered spare parts in the upper hinge or lower block and not exchangeable Note: For Nokia product codes, please refer to the latest Service Bulletins on the Partner Website (PWS).
RM-10;RM-24 Parts Lists and Component Layouts ITEM/CIRCUIT REF.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care ITEM/CIRCUIT REF. QTY PART NAME I203 1 WINDOW FRAME / JOYSTICK DECORATION I204 1 ENGINE QWERTY KEYMAT I205 1 POWER KEY ASSEMBLY I206 4 SCREW M1.
RM-10;RM-24 Parts Lists and Component Layouts ITEM/CIRCUIT REF.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item B2200 C1470 Side Bottom Bottom Grid E G 2 4 Description and value CRYSTAL_3.3X1. 6_H0.9 CRYSTAL 32.768KHZ +-30PPM 12.5PF 32.
RM-10;RM-24 Parts Lists and Component Layouts Item C2108 C2109 C2110 C2200 C2201 C2202 C2203 C2204 C2205 C2206 Side Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Nokia Customer Care Grid H H H G D F F F F F 1 1 1 3 2 2 2 2 2 2 Description and value 0402C Chipcap X7R 10% 50V 0402 1n0 0402C Chipcap X7R 10% 50V 0402 1n0 0402C Chipcap X7R 10% 50V 0402 1n0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0402C Chipcap X7R 10% 50V 0402 1n0 0402
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C2219 C2220 C2221 C2222 C2223 C2224 C2225 C2226 C2227 C2228 C2230 C2231 Side Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Grid E E D E G G D D D D D F 1 4 4 4 3 3 4 3 3 2 1 4 Description and value 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0402C Chipcap X7R 10% 16V 0402 10n 0402C
RM-10;RM-24 Parts Lists and Component Layouts Item C2306 C2307 C2309 C2312 C2313 C2314 C2315 Side Bottom Bottom Bottom Bottom Bottom Bottom Bottom Nokia Customer Care Grid T R T R R Q Q 8 8 8 8 8 8 7 Description and value 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0805C CHIPCAP X5R 22U M 6V3 0805 22u 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0805C_RKNM CHIPCAP X5R 4U7 K 25V 0805 4u7 0805C_RKNM CHIPCAP X5R 4U7 K 25V 0805 4u7
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C2811 C2812 C2813 C2814 Side Top Top Top Top Grid I F F G 9 8 7 9 Description and value 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 1n0 C2815 Top I 9 0402C Chipcap X7R 10% 50V 0402 C2830 Top H 9 0402C Chipcap 5% NP0 10p C3000 Bottom I 1 0402C_H0.
RM-10;RM-24 Parts Lists and Component Layouts Item C4208 C4209 C4210 C4405 C4406 C4407 C4409 C4410 Side Bottom Bottom Bottom Top Top Top Bottom Bottom Nokia Customer Care Grid J I I F L F J J 5 6 5 3 6 3 8 9 Description and value 0603C CHIPCAP X5R 2U2 K 6V3 0603 2u2 0402C CHIPCAP X7R 33N K 10V 0402 33n 0603C CHIPCAP X5R 2U2 K 6V3 0603 2u2 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 4U7 K 6V3 0603 4u7
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C4803 C4804 C4805 C4806 C4807 C4808 C4809 C4810 C4811 C4812 C4813 C5000 C5001 C5002 C5003 C5004 C5005 C5006 C5200 C5201 Page 2 –16 Side Top Top Top Top Top Top Top Top Bottom Top Top Bottom Bottom Bottom Top Bottom Top Bottom Bottom Top Grid I I J J L I I I G I L J J J K J I J R L 7 5 4 7 7 6 6 6 5 4 6 2 2 3 1 3 1 2 6 7 Description and value 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value C5202 Top M 7 0402C CHIPCAP X5R 100N K 10V 0402 C6030 Bottom K 6 0402C Chipcap 5% NP0 100p C6031 Bottom L 7 0402C Chipcap 5% NP0 15p C6033 Bottom K 6 0603C CHIPCAP X5R 4U7 K 6V3 0603 4u7 C6036 Bottom L 7 0603C CHIPCAP X5R 4U7 K 6V3 0603 4u7 C6037 Bottom L 6 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C6038 Bottom L 5 0402C CHIPCAP X5R 1U K 6V3 0402 1u0 C6039 Bot
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C6308 C6309 C6310 C6311 C6312 C6313 C6314 C6315 C6317 C6318 C6319 C6320 C6321 C6322 C6323 C6324 C6325 C6326 C6327 C6330 Page 2 –18 Side Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Grid N M M M M M N N N N N O N P O O O O O K 6 6 8 6 8 6 8 6 8 6 8 6 8 7 8 8 6 8 6 8 Description and value 0402C Chipcap X7R 10% 50V 0402 1n0 0402C Chipcap
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value C6335 Bottom L 8 0402C CHIPCAP NP0 220P J 25V 0402 C6338 Bottom K 8 0402C Chipcap 5% NP0 47p C6340 Bottom L 8 0402C Chipcap +-0.25pF NP0 6p8 C6344 Bottom M 7 0402C Chipcap +-0.25pF NP0 6p8 C6345 Bottom M 7 0402C Chipcap +-0.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item Side Grid Description and value C7508 Top C 5 0402C Chipcap 5% NP0 18p C7509 Top C 4 0402C Chipcap +-0.25pF NP0 2p7 C7512 Bottom C 3 0402C Chipcap +-0.25pF NP0 2p7 C7513 Top D 3 0402C Chipcap X7R 10% 25V 0402 4n7 C7514 Bottom C 4 0402C Chipcap +-0.
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value C7547 Top D 6 0402C Chipcap +-0.25pF NP0 1p8 C7548 Top E 6 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C7549 Top E 7 0402C Chipcap 5% NP0 100p C7550 Top C 6 0402C Chipcap +-0.25pF NP0 2p7 C7552 Top C 6 0402C Chipcap +-0.25pF NP0 2p7 8n2 C7553 Top C 6 0402C Chipcap X7R 10% 16V 0402 C7554 Bottom F 6 0402C Chipcap +-0.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item Side Grid Description and value C7584 Bottom C 4 0402C Chipcap +-0.
RM-10;RM-24 Parts Lists and Component Layouts Item G7500 G7501 G7502 L1470 L1472 L2000 L2001 L2002 Side Top Top Bottom Bottom Bottom Bottom Bottom Bottom Nokia Customer Care Grid D D E F I U U U 2 5 6 4 4 4 6 6 Description and value VCO_FDK_IT_H1. 7 VCO 3610-4340MHZ 2.7V 14MA 3610-43 40MHz NKG3176B_H1.0 VCTCXO 38.4MHZ 2.5V 2MA 38.4MH z VCO_FDK_IT_4 VCO 3296-3980MHZ FOUR 2.7V 20MA 3296-39 80MHz FERRITE_0402 FERRITE BEAD 0.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item L2204 L2205 L2206 L2301 L2302 L2304 L4200 L4201 L4401 L4402 L4403 L4404 L4405 L4406 L4407 L5200 L6030 L6031 L7502 L7503 Page 2 –24 Side Bottom Bottom Bottom Bottom Bottom Bottom Top Top Top Top Top Top Top Top Top Bottom Bottom Bottom Top Bottom Grid D Q J T T Q H I F N N N G G G Q L L C G Description and value FERRITE_0402 FERRITE BEAD 0.6R 600R/ 100MHZ 0402 600R/ 100MHz 0603_BLM FERR.
RM-10;RM-24 Parts Lists and Component Layouts Item L7504 L7505 L7506 L7510 L7511 L7512 L7514 L7515 L7516 L7517 M2100 N2200 N2300 N2301 Side Bottom Bottom Bottom Top Top Top Bottom Bottom Bottom Top Bottom Bottom Bottom Bottom Nokia Customer Care Grid C C C D D D D F C D H E R Q Description and value 0402L CHIP COIL 27N J Q27/800M 0402 27nH 0402L CHIP COIL 12N J Q31/800M 0402 12nH 0402L CHIP COIL 12N J Q31/800M 0402 12nH 0402L CHIP COIL 4N7 +-0N3 Q28/800M 0402 4n7H 0402L CHIP COIL 10N J Q30/
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item Side Grid Description and value N6030 Bottom L 6 uBGA63_4.6X4.6 BRF6150 ~ N6031 Bottom K 6 FC_4_0.99X0.99 LI VREG TK63128B 2.8V WLCSP4 ~ N6300 Bottom N 7 LFBGA_228 WLAN MCM STLC4370 F3 LINEAR EM LFBGA228 ~ N6301 Bottom L 8 RF5924 WLAN RF5924 ES3.5 ~ N6302 Bottom L 8 SOT_666 TRX2+RX4 PEMD9 N&P 10K/47K 0W12 SOT666 ~ N7500 Top D 4 TFBGA_84_6.15X 6.
RM-10;RM-24 Parts Lists and Component Layouts Item R2071 Side Bottom Nokia Customer Care Grid T Description and value 6 0402_NTH5 NTC RES 47K J B=4050 +-3% 0402 ASIP SINGLE ENDED MICROPHONE INTERF BGA8 ~ 47k R2100 Bottom S 6 FLIP_CHIP_8_1.7 X1.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item Side Grid Description and value R4420 Top M 6 0402R Resistor 5% 63mW 100R R4423 Bottom J 9 0805R_THERM1 CHIPRES 0W125 4R7 J 0805 4R7 R4424 Top N 3 0402R Resistor 5% 63mW 10k R4425 Top L 4 0402R Resistor 5% 63mW 10k R4426 Top H 3 0402R Resistor 5% 63mW 1k0 R4427 Bottom D 3 0402R Resistor 5% 63mW 4k7 R4428 Top F 6 0402R Resistor 5% 63mW 4k7 R4429 Top L 6 0402R Resistor 5% 63mW 100
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value R6055 Bottom L 5 0402R Resistor 5% 63mW 100k R6065 Top L 5 0402R Resistor 5% 63mW 10k R6300 Bottom O 8 0402R CHIPRES 0W06 1M F 100PPM 0402 1M0 R6301 Bottom O 6 0402R Resistor 5% 63mW 1k2 R6354 Bottom N 6 0402R Resistor 5% 63mW 3k3 R6424 Bottom K 7 0402R Resistor 5% 63mW 100R R7400 Top E 4 0402R Resistor 5% 63mW 18R R7401 Bottom F 6 0402R Resistor 5%
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item Side Grid Description and value S4429 Top M 5 SWITCH_EVQWH E50K SWITCH MULTIDIRECTIONAL EVQ042Z5003 S4436 Top A 7 BUTTON_EVPAA SWITCH PB LIGHT EVPAA 15V 20MA ~ S4437 Bottom L 1 SWITCH_SKRELX 1_1 SM SW TACT SPST-NO 12VDC 50MA ~ T6030 Bottom L 7 TRANS_LDB213 TRANSF BALUN 2400 +-100MHZ ~ T7500 Top D 5 TRANS_LDB15 TRANSF BALUN 2134 +-90MHZ 0805 ~ T7501 Top C 3 TRANS_LDB15 TRANSF BALUN 3800 +-550MHZ
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value V4411 Top F 7 SC70_6_FAIR MFET N&P SI1867DL VIN>1V8 SOT363 V4412 Top P 8 LED_LWL28G LED LW L28G WHITE 0603 ~ V4413 Top F 9 SC79 SCH DI 1PS79SB31 200MA 30V SOD523 ~ V4414 Top F 7 SC79 SCH DI 1PS79SB31 200MA 30V SOD523 ~ V7500 Bottom E 8 SOT_563 SCHDIX2 RF DETECTOR CT 1PF 0V39 SOT666 ~ X1470 Bottom H 4 SOCKET_DMD104 13 CAMERA MOD.SOCKET 2X7POL SPR P1.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item X7503 X7504 X7505 X7506 Z2000 Z2001 Z2003 Z2004 Z4400 Z4402 Z4403 Z4404 Z4405 Z5200 Z6300 Z7500 Z7501 Side Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Top Top Top Top Top Bottom Bottom Bottom Top Grid C A A B T T T U N N F F F Q K H C Description and value 8 COAX_MM8430 CONN SM COAX+ SW F 50R 250V 6GHZ 8 ANT_SPRING_M3 E_563 ANTENNA SPRING CLIP ~ 8 ANT_SPRING_M3 E_563 ANTENNA SPRING CLIP ~ 1 ANT_SPRING_M3 E_56
RM-10;RM-24 Parts Lists and Component Layouts Item Z7505 Z7506 Side Bottom Top Nokia Customer Care Grid E E Description and value 9 ISOLATOR_CEZ00 47 ISOLATOR 1950+-30MHZ 13DB 3.3X3.4X1.6 ~ 7 FILTER_SAW_2.1 X1.7_H0.8 SAW FILTER 1950+-30MHZ 2.0X1.6X1.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C2004 C2005 C2006 C2011 Side Bottom Bottom Bottom Bottom Grid U U U T 5 6 6 7 Description and value 0402C CERCAP X7R 22N K 16V 0402 22n 0402C Chipcap X7R 10% 16V 0402 10n 0402C Chipcap X7R 10% 16V 0402 10n 0402C CHIPCAP NP0 270P J 25V 0402 270p 470n C2012 Bottom V 4 0603C_H0.
RM-10;RM-24 Parts Lists and Component Layouts Item C2203 C2204 C2205 C2206 Side Bottom Bottom Bottom Bottom Nokia Customer Care Grid F F F F 2 2 2 2 Description and value 0402C Chipcap X7R 10% 50V 0402 1n0 0402C Chipcap X7R 10% 50V 0402 1n0 0402C Chipcap X7R 10% 50V 0402 1n0 0402C Chipcap X7R 10% 50V 0402 1n0 1n0 C2207 Bottom D 2 0402C Chipcap X7R 10% 50V 0402 C2208 Bottom E 1 0402C Chipcap 5% NP0 27p C2209 Bottom E 1 0402C Chipcap 5% NP0 22p C2210 Bottom D 4 0603C
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C2225 C2226 C2227 C2228 C2230 C2231 Side Bottom Bottom Bottom Bottom Bottom Bottom Grid D D D D D F 4 3 3 2 1 4 Description and value 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0805C CHIPCAP X5R 10U M 6V3 0805 10U 1u0 C2232 Bottom I 3 0603C CHIPCAP X5R 1U K 6V3 0603 C2233 B
RM-10;RM-24 Parts Lists and Component Layouts Item C2315 Side Bottom Nokia Customer Care Grid Q 7 Description and value 0805C_RKNM CHIPCAP X5R 4U7 K 25V 0805 4u7 1n0 C2316 Bottom S 6 0402C Chipcap X7R 10% 50V 0402 C2317 Bottom S 8 0402C Chipcap 5% NP0 27p C2701 Bottom O 1 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2800 Top H 6 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2801 Top F 9 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C2802 Top F 7 0402C_H0.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C3000 C3001 C3002 C3003 C3004 C3005 C3006 C3007 Side Bottom Bottom Bottom Top Top Top Top Top Grid I J J I F G G G 1 8 8 8 5 4 4 6 Description and value 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C Chipcap X7R 10% 16V 0402 10n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.
RM-10;RM-24 Parts Lists and Component Layouts Item C4409 C4410 Side Bottom Bottom Nokia Customer Care Grid J J 8 9 Description and value 0603C CHIPCAP X5R 4U7 K 6V3 0603 4u7 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 1n0 C4412 Top L 6 0402C Chipcap X7R 10% 50V 0402 C4413 Top B 7 0402C Chipcap 5% NP0 27p C4414 Top H 3 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 C4415 Top G 3 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n C4416 Top G 3 0402C_H0.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C4809 C4810 C4811 C4812 C4813 C5000 C5001 C5002 C5003 C5004 C5005 C5006 C5200 C5201 Side Top Top Bottom Top Top Bottom Bottom Bottom Top Bottom Top Bottom Bottom Top Grid I I G I L J J J K J I J R L 6 6 5 4 6 2 2 3 1 3 1 2 6 7 Description and value 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.6 CHIPCAP X5R 100N M 16V 0402 100n 0402C_H0.
RM-10;RM-24 Parts Lists and Component Layouts Item C6039 C6040 C6041 C6042 C6043 C6044 Side Bottom Bottom Bottom Bottom Bottom Bottom Nokia Customer Care Grid K K K L L K 6 6 6 7 7 6 Description and value 0402C CHIPCAP X5R 100N K 10V 0402 100n 0402C CHIPCAP X5R 100N K 10V 0402 100n 0402C CHIPCAP X5R 0U47 K 6.3V 0402 0u47 0603C CHIPCAP X5R 1U K 6V3 0603 1u0 0402C CHIPCAP X5R 0U47 K 6.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item C6314 C6315 C6317 C6318 C6319 C6320 C6321 C6322 C6323 C6324 C6325 C6326 C6327 C6330 Side Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Grid N N N N N O N P O O O O O K 8 6 8 6 8 6 8 7 8 8 6 8 6 8 Description and value 0402C CHIPCAP X5R 100N K 10V 0402 100n 0402C CHIPCAP X5R 100N K 10V 0402 100n 0402C CHIPCAP X5R 100N K 10V 0402 100n 0402C Chipcap X7R 10% 50V 0402 1n0 04
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value C6351 Bottom P 6 0402C Chipcap X7R 10% 50V 0402 C6352 Bottom N 6 0402C Chipcap 5% NP0 150p C6360 Bottom M 8 0402C CHIPCAP NP0 220P J 25V 0402 220p C6361 Bottom M 6 0402C CHIPCAP NP0 220P J 25V 0402 220p C6364 Bottom L 7 0402C Chipcap +-0.25pF NP0 6p8 C6365 Bottom L 7 0402C Chipcap +-0.25pF NP0 6p8 C6366 Bottom K 7 0402C Chipcap +-0.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item Side Grid Description and value C7520 Top E 4 0402C Chipcap 5% NP0 18p C7522 Top D 3 0402C Chipcap 5% NP0 150p C7523 Bottom C 4 0402C Chipcap +-0.25pF NP0 3p9 C7524 Top C 2 0603C CHIPCAP NP0 2N2 G 16V 0603 2n2 C7525 Bottom C 5 0402C Chipcap +-0.25pF NP0 3p9 C7526 Top E 5 0402C Chipcap +-0.
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value C7556 Bottom C 6 0402C Chipcap 5% NP0 10p C7559 Bottom C 5 0402C Chipcap +-0.25pF NP0 1p0 C7560 Top C 6 0402C Chipcap X7R 10% 25V 0402 4n7 C7561 Bottom C 6 0402C Chipcap +-0.25pF NP0 4p7 C7563 Bottom C 6 0402C Chipcap +-0.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item D5000 D6030 F2000 G2200 G6030 Side Top Bottom Bottom Bottom Bottom Grid J K U J K Description and value 3 FBGA133_11.6X 13.1 COMBO 512 DDR + 1G NAND FBGA133 PBFREE 32Mx16/ 128Mx8 5 XBGA_N5_H0.62 5 OR-GATE 2INPUT 74LVC1G32YZTR WCSP-5 ~ 4 0603_FUSE_AVX 2MATS SM FUSE F 2.0A 32V 2A 1 BATTER_EECEP RTC BACUP CAPAC 311 SIZE FOR 2.6V 4UAH 2.6V 7 VCTCXO_3.4X2.7 _4P2_H1.0 TCXO 38.4MHZ +-10PPM 2.78V 38.
RM-10;RM-24 Parts Lists and Component Layouts Item L2106 L2202 L2203 L2204 L2205 L2206 L2301 L2302 L2304 L4200 L4201 L4401 L4402 L4403 L4404 L4405 L4406 L4407 L5200 L6030 Issue 1 Side Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Top Top Top Top Top Top Top Top Top Bottom Bottom Nokia Customer Care Grid H D D D Q J T T Q H I F N N N G G G Q L Description and value 0603_BLM FERR.BEAD 220R/100M 2A 0R05 0603 220R/ 100MHz 0603_BLM FERR.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item L6031 L7502 L7503 L7504 L7505 L7506 L7516 L7517 M2100 N2200 N2300 N2301 Side Bottom Top Bottom Bottom Bottom Bottom Bottom Top Bottom Bottom Bottom Bottom Grid L C G C C C C D H E R Q Description and value 0402L CHIP COIL 2N2+-0N3 Q30/800M 0402 2n2H 0402L CHIP COIL 100N J Q16/300M 0402 100nH FERRITE_0402 FERRITE BEAD 0.
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value N6300 Bottom N 7 LFBGA_228 WLAN MCM STLC4370 F3 LINEAR EM LFBGA228 N6301 Bottom L 8 RF5924 WLAN RF5924 ES3.5 ~ N6302 Bottom L 8 SOT_666 TRX2+RX4 PEMD9 N&P 10K/47K 0W12 SOT666 ~ N7500 Top D 4 TFBGA_84_6.15X 6.15 RF ASIC HINKU310A TFBGA84 ~ N7501 Top D 7 TFBGA64_H1.2 RF ASIC VINKU314A TFBGA64 ~ N7502 Bottom B 6 RITSA_PA_REL3 PW AMP RF9292E9.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item R2103 R2104 R2105 R2106 Side Top Top Top Bottom Grid F F F F 3 3 4 5 Description and value 0402R Chipres 0W06 jumper 0402 0R 0402_VAR CHIP VARISTOR VWM14V VC50V 0402 14V/50V 0402_VAR CHIP VARISTOR VWM14V VC50V 0402 14V/50V 0402_VAR CHIP VARISTOR VWM14V VC50V 0402 14V/50V 14V/50V R2107 Bottom G 5 0402_VAR CHIP VARISTOR VWM14V VC50V 0402 R2200 Bottom F 2 0402R Resistor 5% 63mW 100k R2201 Bottom D 1 0402R
RM-10;RM-24 Parts Lists and Component Layouts Item Side Nokia Customer Care Grid Description and value R4427 Bottom D 3 0402R Resistor 5% 63mW 4k7 R4428 Top F 6 0402R Resistor 5% 63mW 4k7 R4429 Top L 6 0402R Resistor 5% 63mW 100k R4432 Top F 7 0402R Chipres 0W06 jumper 0402 0R R4433 Top F 8 0402R Resistor 5% 63mW 1k0 R4434 Top F 8 0402R Resistor 5% 63mW 1k0 R4435 Top F 8 0402R Resistor 5% 63mW 47R R4436 Top F 8 0402R Resistor 5% 63mW 10R R4439 Top
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item Side Grid Description and value R6424 Bottom K 7 0402R Resistor 5% 63mW 100R R7400 Top E 4 0402R Resistor 5% 63mW 18R R7401 Bottom F 6 0402R Resistor 5% 63mW 10R R7402 Top E 3 0402R Resistor 5% 63mW 10R R7501 Top E 2 0402R Resistor 5% 63mW 1k0 R7503 Bottom E 4 0402R Resistor 5% 63mW 4k7 R7504 Top E 4 0402R CHIPRES 0W06 10K F 0402 10k R7505 Top C 2 0402R CHIPRES 0W06 8K2 F 0402 8
RM-10;RM-24 Parts Lists and Component Layouts Item T6030 T7501 T7502 T7503 V2000 Side Bottom Top Bottom Bottom Bottom Nokia Customer Care Grid L C C D U 7 3 7 6 5 Description and value TRANS_LDB213 TRANSF BALUN 2400 +-100MHZ ~ TRANS_LDB15 TRANSF BALUN 3800 +-550MHZ 0805 ~ TRANS_LDB15 TRANSF BALUN 1800 +-100mhz 2x1.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Item X2001 X2002 X2003 X2060 X2070 X2105 X2106 X2700 X4401 X4402 X5200 X6300 X7500 X7501 X7502 X7506 Z2000 Z2001 Z2003 Z2004 Page 2 –54 Side Bottom Bottom Bottom Top Bottom Bottom Bottom Bottom Top Top Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Bottom Grid V V V E I H G M B M S O A A C B T T T U Description and value 6 SYSCON_MQ202_ NK_14R3 SM SYSTEM CONNECTOR 14POL ~ 3 CONTACT_PAD_2. 95X1.
RM-10;RM-24 Parts Lists and Component Layouts Item Z4400 Z4402 Z4403 Z4404 Z4405 Z5200 Z6300 Z7500 Side Top Top Top Top Top Bottom Bottom Bottom Nokia Customer Care Grid N N F F F Q K H Description and value 7 uBGA24_2.62X2. 62 ASIP EMIF10-1K010F2 **PB-FREE** ~ 4 uBGA24_2.62X2. 62 ASIP EMIF10-1K010F2 **PB-FREE** ~ 2 uBGA25_2.47X2. 47 ASIP 10-CH ESD EMI FILTER BGA25 ~ 3 uBGA25_2.47X2. 47 ASIP 10-CH ESD EMI FILTER BGA25 ~ 2 uBGA25_2.47X2.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Figure 3 1em-25b Component layouts - bottom 1em-25a and 1em-25b Figure 4 1em-25a Page 2 –56 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care Figure 5 1em-25b Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Parts Lists and Component Layouts Nokia Customer Care (This page left intentionally blank.) Page 2 –58 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care 3 — Service Software Instructions Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Software Instructions Nokia Customer Care (This page left intentionally blank.) Page 3 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Software Instructions Nokia Customer Care Table of Contents Phoenix installation steps in brief........................................................................................................................3–5 Installing Phoenix...................................................................................................................................................3–6 Updating Phoenix installation.........................................................................
RM-10;RM-24 Service Software Instructions Nokia Customer Care (This page left intentionally blank.) Page 3 –4 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Software Instructions Nokia Customer Care Phoenix installation steps in brief Prerequisites Recommended hardware requirements: • Computer processor: Pentium 700 MHz or higher • RAM 256 MB • Disk space 100-300 MB Supported operating systems: • Windows 2000 Service Pack 3 or higher • Windows XP Service Pack 1 or higher Context Phoenix is a service software for reprogramming, testing and tuning phones.
RM-10;RM-24 Service Software Instructions Nokia Customer Care Results Phoenix is ready to be used with FPS-10 flash prommer and other service tools. Installing Phoenix Prerequisites • Check that a dongle is attached to the parallel port of your computer. • Download the Phoenix installation package (for example, phoenix_service_sw_2004_39_x_xx.exe) to your computer (in C:\TEMP, for instance). • Close all other programs.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 3. Read the disclaimer text carefully and click Yes. Figure 7 Disclaimer text 4. Choose the destination folder. The default folder C:\ProgramFiles\Nokia\Phoenix is recommended. 5. To continue, click Next. To choose another location, click Browse (not recommended). 6. Wait for the components to be copied. The progress of the installation is shown in the Setup Status window. 7. Wait for the drivers to be installed and updated.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 8. To end the installation, click Finish. Figure 8 InstallShield Wizard Complete Next actions After the installation, Phoenix can be used after: • installing phone model specific data package for Phoenix • configuring users and connections FPS-10 flash prommer can be used after updating their flash update package files.
RM-10;RM-24 Service Software Instructions Nokia Customer Care Figure 9 Installation interrupted • Always follow the instructions on the screen. Steps 1. Download the installation package to your computer hard disk. 2. Close all other programs. 3. Run the application file (for example, phoenix_service_sw_2004_39_x_xx.exe). Results A new Phoenix version is installed and driver versions are checked and updated.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 2. To uninstall Phoenix, choose Phoenix Service Software→Change/Remove→Remove . Figure 10 Remove program The progress of the uninstallation is shown. 3. If the operating system does not require rebooting, click Finish to complete. Figure 11 Finish uninstallation Page 3 –10 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Software Instructions Nokia Customer Care If the operating system requires rebooting, InstallShield Wizard will notify you. Select Yes... to reboot the PC immediately and No... to reboot the PC manually afterwards. Repairing Phoenix installation Context If you experience any problems with the service software or suspect that files have been lost, use the repair function before completely reinstalling Phoenix.
RM-10;RM-24 Service Software Instructions Nokia Customer Care • Files for type label printing • Validation file for the fault log repair data reporting system • All product-specific configuration files for Phoenix software components Data files are stored in C:\Program Files\Nokia\Phoenix (default). Installing phone data package Prerequisites • A phone-specific data package contains all data required for the Phoenix service software and service tools to be used with a certain phone model.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 2. Click Next. 3. In the following view you can see the contents of the data package. Read the text carefully. There is information about the Phoenix version required with this data package. Figure 13 Data package setup information 4. To continue, click Next. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 5. Choose the destination folder, and click Next to continue. Figure 14 Data package destination folder The InstallShield Wizard checks where Phoenix is installed, and the directory is shown. 6. To start copying the files, click Next. Page 3 –14 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Software Instructions Nokia Customer Care Phone model specific files are installed. Please wait. 7. To complete the installation, click Finish. Figure 15 InstallShield Wizard Complete Next actions Phoenix can be used for flashing phones and printing type labels after: • Configuring users • Managing connections FPS-10 can be used after updating their flash update package files.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 3. To uninstall the data package, click OK or to interrupt the uninstallation, click Cancel. Figure 16 Uninstalling phone data package 4. When the data package is uninstalled, click Finish. Figure 17 Finishing data package uninstallation Alternative steps • You can also uninstall the data package manually from Control Panel→Add/Remove Programs→xx-xx* Phone Data Package . (*= type designator of the phone).
RM-10;RM-24 Service Software Instructions Nokia Customer Care Configuring users in Phoenix Steps 1. Start Phoenix service software, and log in. Figure 18 Phoenix login If the user ID is already configured, select s/he from the User name drop-down list, and click OK. 2. To add a new user, or to edit existing ones, click Maintain. 3. To add a new user, click New. 4. Type in the name and initials of the user, and click OK. The user is added to the user name list. 5.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 3. To add a new connection, click Add. 4. Select Manual mode, and click Next to continue. If you want to create the connection using the Connection Wizard, connect the tools and a phone to your PC. The wizard will automatically try to configure the correct connection.
RM-10;RM-24 Service Software Instructions Nokia Customer Care iv For a plain USB connection, choose the following connection settings: Note: First connect the DKU-2 USB cable between the PC USB port and phone. • Media: USB 5. To complete the configuration, click Finish. 6. Click the connection you want to activate. Use the up/down arrows located on the right hand side to move it on top of the list, then click Apply.
RM-10;RM-24 Service Software Instructions Nokia Customer Care Steps 1. To begin installation, double- click flash_update_x_yy.exe . Figure 24 Flash update welcome dialog If the same version of Flash Update package already exists, and you want to reinstall it, the previous package is first uninstalled. Restart installation again after that. 2. If you try to downgrade the existing version to older ones, the setup will be aborted.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 3. It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia \Phoenix. Click Next to continue. Figure 26 Flash destination folder When installing the flash update files for the first time you may choose another location by selecting Browse. However, this is not recommended. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 4. To complete the installation procedure, click Finish . Figure 27 Finish flash update Next actions FPS-10 flash prommers must be updated using Phoenix! Updating FPS-10 flash prommer software Steps 1. Start Phoenix Service Software and log in, manage connection correctly for your flash prommer. 2. Choose Flashing→Prommer maintenance . 3.
RM-10;RM-24 Service Software Instructions Nokia Customer Care 5. Wait until you are notified that update has been successful; the procedure will take a couple of minutes. Click OK to close the Update Done window. Figure 28 Prommer SW update finished 6. If you are using the FPS-10 flash prommer, check that it is detected from the progress info. Check also the status leds in the FPS-10. The MODE2 led (green), VBAT and POWER leds (red) should be lit.
RM-10;RM-24 Service Software Instructions Nokia Customer Care Alternative steps • You can update FPS-10 SW by clicking the Update button and selecting the appropriate fpsxupd.ini file in C:\Program Files\Nokia\Phoenix\Flash. Figure 30 Flash directory window • All files can be loaded separately to the prommer used. To do this, click the right mouse button in the Flash box files window and select the file type to be loaded. More information can be found in Phoenix Help.
Nokia Customer Care 4 — Service Tools and Service Concepts Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care (This page left intentionally blank.) Page 4 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care Table of Contents Service tools............................................................................................................................................................4–5 CA-31D................................................................................................................................................................4–5 CA-35S............................................................................
Nokia Customer Care RM-10;RM-24 Service Tools and Service Concepts Figure 34 MJ-39_cardreader_RF...........................................................................................................................4–18 Figure 35 SS-62_FS-2_FPS-10...............................................................................................................................4–19 Figure 36 SS-62_FPS-10_RF_EU...................................................................................................
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care Service tools The table below gives a short overview of service tools that can be used for testing, error analysis and repair of product RM-10;RM-24, refer to various concepts. CA-31D USB cable The CA-31D USB cable is used to connect FPS-10 or FPS-11 to a PC. It is included in the FPS-10 and FPS-11 sales packages.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care CU-4 Control unit CU-4 is a general service tool used with a module jig and/or a flash adapter. It requires an external 12 V power supply. The unit has the following features: • software controlled via USB • EM calibration function • Forwards FBUS/Flashbus traffic to/from terminal • Forwards USB traffic to/from terminal • software controlled BSI values • regulated VBATT voltage • 2 x USB2.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care FLS-5 Flash device FLS-5 is a dongle and flash device incorporated into one package, developed specifically for POS use.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care JBT-9 Bluetooth test and interface box (sales package) The JBT-9 test box is a generic service device used to perform Bluetooth bit error rate (BER) testing, and establishing cordless FBUS connection via Bluetooth. An ACP-8x charger is needed for BER testing and an AXS-4 cable in case of cordless interface usage testing .
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care PCS-1 Power cable The PCS-1 power cable (DC) is used with a docking station, a module jig or a control unit to supply a controlled operating voltage. PKD-1 SW security device SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC. Without the device, it is not possible to use the service software.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care RJ-82 Soldering jig RJ-82 is a soldering jig used for soldering and as a rework jig for the engine module. SA-80 RF coupler for RM-24 SA-80 is an RF coupler for GSM RF testing. It is used together with the product specific flash adapter FS-2 and flash adapter base SS-62. The following table shows attenuations from the antenna pads of the mobile terminal to the SMA connectors of SA-80: Table 2 RM-24/US 1 System Channel Tx-att.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care SA-98 RF coupler for RM-10 SA-98 is an RF coupler for GSM and WCDMA testing.. Table 3 RM-10/3G 1 System Channel Tx-att. (dB) Rx-att. (dB) EGSM 900 975 5.2 7 38 4.8 9 124 4.7 10 512 7.9 6 698 7.3 6 885 6 6 512 6.3 7 700 6.3 8 810 6.3 10 GSM 1800 GSM 1900 Table 4 RM-10/3G 2 System Channel Tx-att. (dB) Rx-att. (dB) 9612 / 10562 10 8 9750 / 10700 7.4 8 9888 / 10838 9.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care SPS-1 Soldering Paste Spreader SRT-6 Opening tool SRT-6 is used to open phone covers and B-to-B connectors. SS-46 Interface adapter SS-46 acts as an interface adapter between the flash adapter and FPS-10.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care SS-70 Domesheet assembly jig ST-21 Rework stencil ST-21 is a rework stencil used with rework jig RJ-56. ST-22 Rework stencil ST-22 is a rework stencil used with rework jig RJ-57. SX-4 Smart card SX-4 is a BB5 security device used to protect critical features in tuning and testing. SX-4 is also needed together with FPS-10 when DCT-4 phones are flashed. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care XCS-4 Modular cable XCS-4 is a shielded (one specially shielded conductor) modular cable for flashing and service purposes. XRS-6 RF cable The RF cable is used to connect, for example, a module repair jig to the RF measurement equipment. SMA to N-Connector approximately 610 mm. Attenuation for: • GSM850/900: 0.3+-0.1 dB • GSM1800/1900: 0.5+-0.1 dB • WLAN: 0.6+-0.1dB Page 4 –14 COMPANY CONFIDENTIAL Copyright © 2006 Nokia.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care Service concepts E70_SS-46_FS-2_FPS-10 Figure 31 SS-46_FS-2_FPS-10 Note: FPS-8 concept can also be used for flashing. Description Type FS-2 Flash adapter SS-46 Interface adapter XMS-3 Modular cable Standard USB cable FPS-10 Flash prommer box Standard USB cable PKD-1 Issue 1 SW security device COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care E70_MJ-39_FPS-10_RF Figure 32 MJ-39_FPS-10_RF Type Description MJ-39 Module jig CU-4 Control unit FPS-10 Flash prommer box SX-4 Smart card PCS-1 DC power cable Standard USB cable Standard USB cable GPIB control cable XRS-6 RF cable PKD-1 SW security device RF shield box Page 4 –16 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care E70_POS_service concepts Figure 33 POS_service concepts Type Description CA-53 USB connectivity cable FLS-4s POS flash device Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care E70_MJ-39_cardreader_RF Figure 34 MJ-39_cardreader_RF Description Type MJ-39 Module jig CU-4 Control unit Standard USB cable PCS-1 DC power cable Standard USB cable + smart card reader SX-4 Smart card XRS-6 RF cable GPIB control cable PKD-1 SW security device RF shield box Page 4 –18 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care E70_SS-62_FS-2_FPS-10 Figure 35 SS-62_FS-2_FPS-10 Note: FPS-8 concept can also be used for flashing. Description Type SS-62/FS-2 Flash adapter CU-4 Control unit XMS-3 Modular cable PCS-1 Power cable FPS-10 Flash prommer box Standard USB cable Standard USB cable PKD-1 Issue 1 SW security device COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care E70_SS-62_FPS-10_RF_EU Figure 36 SS-62_FPS-10_RF_EU Type Description SS-62/FS-2 Flash adapter CU-4 Control unit SA-80/SA-98 RF coupler PCS-1 Power cable Standard USB cable Standard USB cable + smart card reader SX-4 Smart card GPIB control cable XRS-6 RF cable PKD-1 SW security device RF shield box Page 4 –20 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care E70_SS-62_FS-2_FPS-10_RF_US Figure 37 SS-62_FS-2_FPS-10_RF_US Type Description SS-62/FS-2 Flash adapter CU-4 Control unit SA-80/SA-98 RF coupler PCS-1 Power cable Standard USB cable Standard USB cable + smart card reader SX-4 Smart card GPIB control cable XRS-6 RF cable PKD-1 SW security device RF shield box Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Service Tools and Service Concepts Nokia Customer Care (This page left intentionally blank.) Page 4 –22 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care 5 — Disassembly/Reassembly Instructions Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care RM-10;RM-24 Disassembly/Reassembly Instructions (This page left intentionally blank.) Page 5 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care Table of Contents Disassembly / reassembly instructions................................................................................................................5–5 List of Figures Figure 38 Needed tools..........................................................................................................................................5–5 Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care RM-10;RM-24 Disassembly/Reassembly Instructions (This page left intentionally blank.) Page 5 –4 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care Disassembly / reassembly instructions Prerequisites Figure 38 Needed tools. Note: Reassembly takes place in the reverse order. Note the reassembly-specific instructions in steps 4., 12., 30., 34. and 44. Steps 1. Protect the window with a film. 2. Unlock and remove the BATTERY COVER. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 3. Remove the ANTENNA MODULE, beginning from the battery compartment. 4. Unscrew the four Torx Plus® size 6 SCREWS in the order shown. Note: For assembly, use a reverse order and Torque driver with a torque setting of 20Ncm. 5. Open the FLIP MODULE. 6. Lift a bit the A-COVER. Page 5 –6 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions 7. Remove the A-COVER ASSY in the shown order. 8. Cover the LCD MODULE with a protective film. 9. Remove the ENGINE QWERTY KEYMAT. Nokia Customer Care 10. Remove the POWER KEY. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care RM-10;RM-24 Disassembly/Reassembly Instructions 11. Remove the JOYSTICK HAT. 12. For assembly only! Note the correct position when reassembling the JOYSTICK. 13. The FLIP HINGE is connected with the COAX CABLE to the ENGINE MODULE. 14. Very gently, open the COAX CONNECTOR by using angled tweezers. Page 5 –8 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 15. The FLIP MODULE is attached to the B-COVER with two snaps. 16. Place the SS-93 between the B-COVER edge and the clip of the FLIP MODULE and release it carefully. 17. Carefully, turn over the unit securing the FLIP MODULE. Do not yet separate the parts from each other. 18. Unlock another clip of the FLIP MODULE carefully. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 19. Lift the FLIP MODULE a bit and place the flex connector opening tool as shown. 20. Gently open the flex connector. 21. Remove the EARPIECE. 22. Lift the COAX CABLE connector a bit from its holder with tweezers. Page 5 –10 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 23. Gently, press out the LCD MODULE from the HINGE ASSEMBLY. 24. Remove the LCD MODULE paying attention to the COAX CABLE. 25. Unlock the T9 COVER in the order shown. 26. Continue on the other side. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 27. Pull up the T9 COVER and remove it. 28. Remove the T9 KEYMAT. 29. Open the COAX CABLE connector with angled tweezers. 30. For assembly only! Note the correct position of the COAX CABLE when reassembling the unit. Page 5 –12 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 31. Press out the FLIP PWB ASSEMBLY. 32. Remove the modules from the FLIP FRAME. 33. Separate the FLIP QWERTY KEYMAT from the FLIP PWB ASSEMBLY. 34. Unscrew the two Torx Plus size 6 SCREWS in the order shown. Note: For assembly use a reverse order and Torque driver with a torque setting of 21Ncm. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 35. Remove the ENGINE MODULE from the B-COVER. 36. Remove the VOICE KEY. 37. Remove the DC- JACK with the DC-Plug. 38. Use the dental tool as a lever to remove the MICROPHONE. Do not reuse the MICROPHONE. Page 5 –14 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 39. Remove the CAMERA GASKET. 40. Use the A-COVER as a support when removing the CAMERA MODULE. 41. Note the correct position of the SS-15 before placing it over the CAMERA MODULE. 42. Press the SS-15 lightly in shown direction until the CAMERA MODULE have been unlocked. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Disassembly/Reassembly Instructions Nokia Customer Care 43. Press the Camera removal tool together. 44. Gently, remove the CAMERA MODULE. Note the correct position of the Camera when reassembling the unit. 45. Remove the BATTERY DECK. Do not use to much force. Page 5 –16 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care 6 — BB Troubleshooting and Manual Tuning Guide Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide (This page left intentionally blank.) Page 6 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Table of Contents Baseband troubleshooting....................................................................................................................................6–5 Dead or jammed device troubleshooting............................................................................................................6–7 General power checking troubleshooting......................................................................
Nokia Customer Care RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Table 6 Pixel defects............................................................................................................................................6–27 Table 7 Calibration value limits..........................................................................................................................6–55 List of Figures Figure 39 SD clk cdm diagram.................................................................
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Baseband troubleshooting Context This section is intended to be a guide for localising and repairing electrical faults. The fault repairing is divided into troubleshooting paths. The following main troubleshooting tree describes the different baseband troubleshooting paths to be followed in fault situations. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Troubleshooting flow Page 6 –6 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Dead or jammed device troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care General power checking troubleshooting Troubleshooting flow Page 6 –8 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care CMT and application processor clocking troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care Page 6 –10 RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Charging troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Battery current measuring fault troubleshooting Troubleshooting flow Page 6 –12 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Flash programming fault troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care Page 6 –14 RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care CMT SDRAM memory troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care CMT NOR flash fault troubleshooting Troubleshooting flow Page 6 –16 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Application processor memory troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Application processor troubleshooting Troubleshooting flow Page 6 –18 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Power key troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care USB interface troubleshooting Troubleshooting flow Page 6 –20 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care SIM card troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care SD card troubleshooting Troubleshooting flow Page 6 –22 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 39 SD clk cdm diagram Figure 40 SD data 0_1 diagram Figure 41 SD data 2_3 diagram Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Keyboard troubleshooting Troubleshooting flow Page 6 –24 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Flip keyboard troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Engine keyboard troubleshooting Troubleshooting flow Page 6 –26 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Display module troubleshooting General instructions for display troubleshooting Context • The display is in a normal mode when the phone is in active use. • Display is in a partial idle mode when the phone is in the screen saver mode. • The operating modes of the display can be controlled with the help of Phoenix. Table 5 Display module troubleshooting cases Display blank There is no image on the display.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Steps 1. Verify with a working display that the fault is not on the display module itself. The display module cannot be repaired. 2. Check that the cellular engine is working normally. i To check the functionality, connect the phone to a docking station. ii StartPhoenix service software. iii Read the phone information to check that also the application engine is functioning normally (you should be able to read the APE ID). 3.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Display fault troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Display and keyboard backlight troubleshooting Troubleshooting flow Page 6 –30 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care ALS troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care LED driver troubleshooting Troubleshooting flow Page 6 –32 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care WLAN troubleshooting Introduction to WLAN troubleshooting The main problem that can occur is malfunction in WLAN or WLAN ASICs or WLAN SMD components. Such problems are unpredictable and may have many causes, either HW or SW related. Note: When WLAN ASIC or WLAN/BTH front-end-module is changed, WLAN tuning is required. WLAN tuning is also required when permanent memory is replaced or corrupted.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care 2. Start Phoenix service software and turn the phone to the local mode. 3. 3. From the Testing menu, choose WLAN Configuration, following window should pop up. 4. 4. Turn the power state on and press Scan 5. 5. After few seconds, list of found WLAN networks should be updated if WLAN is working, and at least station with SSID name default should be found and signal field should show value close to 75 (+/-10).
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care WLAN failure troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care WLAN FEM troubleshooting Troubleshooting flow Page 6 –36 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care WLAN BT/TCXO troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Bluetooth troubleshooting Introduction to Bluetooth troubleshooting There are two main Bluetooth problems that can occur: Problem Description Detachment of the BT antenna. This would most likely happen if the device has been dropped repeatedly to the ground. It could cause the BT antenna to become loose or partially detached from the PWB.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 45 BT component layout Bluetooth settings for Phoenix Steps 1. Start Phoenix service software. 2. From the File menu, choose Open Product, and then choose the correct type designator from the Product list. 3. Place the phone to a flash adapter in the local mode. 4. Choose Testing→Bluetooth LOCALS . 5. Locate JBT-9’s serial number (12 digits) found in the type label on the back of JBT-9.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 46 BER test result Bluetooth self tests in Phoenix Steps 1. Start Phoenix service software. 2. ChooseFile→Scan Product. 3. Place the phone to a flash adapter. 4. From the Mode drop-down menu, set mode to Local. 5. Choose Testing→Self Tests. 6.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care 7. To run the tests, click Start. Figure 47 Bluetooth self tests in Phoenix Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Bluetooth BER failure troubleshooting Troubleshooting flow Page 6 –42 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care BT audio failure troubleshooting Troubleshooting flow Page 6 –44 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Audio troubleshooting Audio troubleshooting test instructions Differential external earpiece and internal earpiece outputs can be measured either with a single-ended or a differential probe. When measuring with a single-ended probe each output is measured against the ground. Internal handsfree output is measured using a current probe, if a special low-pass filter designed for measuring a digital amplifier is not available.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Loop test Input terminal Output terminal External Mic to External Earpiece XMICP and GND HSEAR R P, HSEAR R N and GND Path Input Differential gain [dB] voltage output (fixed) [mVp-p] voltage [mVp-p] Output DC level [V] Output current [mA] -2.9 1000 720 1.2 NA -4.5 1000 600 1.2 NA -5 1000 560 0 25mA (calc.) 22.7 100 1360 1.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Measurement data Figure 48 Single-ended output waveform of the Ext_in_HP_out measurement when earpiece is connected. If a special low-pass filter designed for measuring digital amplifiers is unavailable, the measurement must be performed with a current probe and the input signal frequency must be 2kHz. Figure 49 Differential output waveform of the Ext_in_IHF_out out loop measurement when speaker is connected.
Nokia Customer Care RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Figure 50 Single-ended output waveform of the HP_in_Ext_out loop when microphone is connected. Page 6 –48 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Earpiece troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Microphone troubleshooting Troubleshooting flow Page 6 –50 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care IHF troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care External microphone troubleshooting Troubleshooting flow Page 6 –52 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care External earpiece troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide VIBRA troubleshooting Troubleshooting flow Page 6 –54 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide Nokia Customer Care Baseband manual tuning guide Energy management calibration Prerequisites Energy Management (EM) calibration is performed to calibrate the setting (gain and offset) of AD converters in several channels (that is, battery voltage, BSI, battery current) to get an accurate AD conversion result. Hardware setup: • An external power supply is needed. • Supply 12V DC from an external power supply to CU-4 to power up the phone.
Nokia Customer Care RM-10;RM-24 BB Troubleshooting and Manual Tuning Guide (This page left intentionally blank.) Page 6 –56 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care 7 — RF Troubleshooting and Manual Tuning Guide Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide (This page left intentionally blank.) Page 7 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Table of Contents Introduction to RF troubleshooting.....................................................................................................................7–5 RF key component placement...............................................................................................................................7–5 Troubleshooting test point locations.....................................................................
Nokia Customer Care RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Figure 56 Test point locations for spectrum analyser - top...............................................................................7–9 Figure 57 Test points for oscilloscope - bottom...............................................................................................7–10 Figure 58 Test points for oscilloscope - top.......................................................................................................
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Introduction to RF troubleshooting All measurements should be done using: • spectrum analyser with a high-frequency high-impedance passive probe (LO-/reference frequencies and RF power levels) • oscilloscope with a 10:1 probe (DC-voltages and low frequency signals) Caution: A mobile phone WCDMA transmitter should never be tested with full Tx power, if there is no possibility to perform the measurements in a good performance RF-shie
Nokia Customer Care RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Figure 51 RM-24 bottom differences in key component placement Figure 52 RM-24 top diffecences in key component placement Page 7 –6 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 53 RM-10 bottom key component placement Figure 54 RM-10 top key component placement Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Troubleshooting test point locations Test points for spectrum analyser Figure 55 Test point locations for spectrum analyser - bottom Page 7 –8 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 56 Test point locations for spectrum analyser - top Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Test points for oscilloscope Figure 57 Test points for oscilloscope - bottom Page 7 –10 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 58 Test points for oscilloscope - top Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Receiver troubleshooting Introduction to Rx troubleshooting Rx can be tested by making a phone call or in the local mode. For the local mode testing, use Phoenix service software. The primary Rx troubleshooting parameter RSSI (Receiving Signal Strength Indicator).
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 4. In the RSSI Reading window, select the appropriate band and channel. Figure 59 RSSI Reading window 5. To start the measurement, activate GSM Rx chain, click Start. Results RSSI reading values of the selected band and channel are displayed. The RSSI level must be the same value which is set at the signal generator (-80 dBm). WCDMA Rx chain activation for manual measurement Steps 1. Start Phoenix service software. 2.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 60 Rx Control window • Set AGC Mode to Algorithm. • Set Channel to 10700. • Set AFC Algorithm to OFF (Default = OFF). Next actions When settings are ready, click Start to activate them. If settings are changed later on (for example, you give a new channel number), you will need to click Stop and Start again.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 4. To perform the measurement, click Start. Transmitter troubleshooting General instructions for Tx troubleshooting Context • Tx troubleshooting requires Tx operation. • Do not transmit on frequencies that are in use! • Transmitter can be controlled in the local mode for diagnostic purposes. • The most useful Phoenix tool for GSM transmitter testing is "RF Controls"; in WCDMA transmitter testing the best tool is "Tx Control".
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Normally a spectrum analyser is used as measurement equipment. Note: The maximum input power of a spectrum analyser is +30 dBm. To prevent any damage, it is recommended to use 10 dB attenuator on the spectrum analyzer input. 4. Set Tx on. i Set the phone module to the test jig and start Phoenix service software. ii Initialize connection to the phone. (With FPS-8 use FBUS driver when using DAU-9S and COMBOX driver).
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 61 RF Controls window • WCDMA troubleshooting i From the Testing menu, activate the Tx Control window:Testing -> WCDMA -> Tx Control . ii In the Tx Control window: • Select the Algorithm mode tab. • Set Start level to “0” dBm (Default = “0”). • Set Step size, Step count and Sequence to “0” (Default = “0”). • Set Scrambling code class to “LONG” (Default = “LONG”). • Set Scrambling code to “16” (Default = “16”).
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 62 Tx Control window Next actions When settings are done, click “Send” to enable them. If you change the settings (e.g. give a new channel number), you need to click “Stop” and “Send” again. Checking antenna functionality The main antenna has two separate antenna elements: GSM and WCDMA. In the GSM antenna, there is one Feed and two GND contacts. In the WCDMA antenna, there is one Feed and one GND contact.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Figure 64 RM-24 antenna The antenna is functioning normally when the contacts function (RDC = 0 ohm) and the antenna is visually intact. RF tunings Introduction to RF tunings Phone RF is tuned in production. There is no reason to do the re-calibration unless: • One or more of the RF components is changed • FLASH memory chip (D3000) is changed or otherwise corrupted.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care RF autotuning RF autotuning Prerequisites For information on the recommended test set-up, refer to the corresponding information on the Partner Website or Nokia Online. Before you can use the autotuning feature, the GPIB driver from the GPIB card vendor must be installed and running. The autotune .xml file must be in a correct place: C:\Program Files\Nokia\Phoenix\products\xx-x* \rfconf_xx-x*.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 10. In the Auto-Tune options window, ensure the Enable showing of message boxes check box is checked, and click OK. 11. Connect the phone WCDMA RF port to the communication tester, and click Tune. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 12. Change the phone RF adapter from WCDMA port to GSM port. 13. To complete the RF autotuning, click OK. Results Autotuning completed successfully! message appears. RF manual tuning guide Required manual tunings after component changes Important: After RF component changes, always use autotuning. Manual tunings are only required in rare cases. If, however, manual tuning is used, only relevant tunings should be performed.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Changed component Perform the following tunings Any component in the GSM Tx RF chain before the PA Tx IQ Tuning, Tx Power Level Tuning Any component in the GSM Tx RF chain after the PA or PA Tx Power Level Tuning Any component in the WCDMA Tx RF chain before the PA Tx AGC & Power Detector, Tx Band Response Calibration, Tx LO Leakage Any component in the WCDMA Tx or Rx chain after the PA, power detector or PA switch mode pow
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Results Figure 65 Rf channel filter calibration typical values PA (power amplifier) detection Context The PA detection procedure detects which PA manufacturer is used for phone PAs. If a PA is changed or if the permanent memory (PMM) data is corrupted, PA detection has to be performed before Tx tunings. Steps 1. From the Operating mode drop-down menu, set mode to Local. 2. Choose Tuning→PA Detection . 3. Click Tune. 4.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 3. Click Tune. Table 9 Temperature sensor calibration tuning limits Min Typ Max Unit -20 -4 20 V 4. To save the calibration values, click Write. 5. To finish the calibration, click Close. GSM receiver tunings Rx calibration (GSM) Context Rx Calibration is used to find out the real gain values of the GSM Rx AGC system and tuning response of the AFC system (AFC D/A init value and AFC slope) Steps 1.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 6. Click Start (if not active already). 7. Click Calibrate. 8. Connect signal generator to the phone and set frequency and amplitude as instructed in the "Rx Calibration with band EGSM900" popup window. The calibration uses a non-modulated CW signal. Increase the signal generator level by cable attenuation and module jig probe attenuation! Page 7 –26 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide 9. Nokia Customer Care To perform tuning, click OK. 10. Check that the tuning values are within the limits specified in this table: Table 10 RF tuning limits in Rx calibration Min Typ Max Unit AFC Value -200 -105...62 200 AFC slope 0 122 200 106 107...110 114 dB 104 104...109 114 dB 104 104...109 114 dB GSM850/GSM900 RSSI0 GSM1800 RSSI0 GSM1900 RSSI0 11. To save values to the phone, click "Save & Continue". 12.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Results Rx band filter response compensation (GSM) Prerequisites Rx Calibration must be performed before the Rx Band Filter Response Compensation. Context On each GSM Rx band, there is a band rejecting filter in front of the HINKU front end. The amplitude ripple caused by these filters causes ripple to the RSSI measurement and therefore calibration is needed. The calibration has to be repeated for each GSM band. Steps 1.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide 6. Click Start. 7. Click Save & Continue. Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 8. Connect the signal generator to the phone and set frequency and amplitude as instructed in the "Rx Band Filter Response Compensation for EGSM900" popup window. 9. To perform tuning, click OK. 10. Go through all 9 frequencies. 11. Check that the tuning values are within the limits specified in the following table: Min Typ Max Unit Ch. 965 / 923.26771 MHz -10 -1 5 dB Ch. 975 / 925.26771 MHz -3 0 5 dB Ch.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Min Typ Max Unit -10 -1 5 dB Ch. 497 / 1802.26771 MHz -10 -1 5 dB Ch. 512 / 1805.26771 MHz -3 0 5 dB Ch. 535 / 1809.86771 MHz -3 0 5 dB Ch. 606 / 1824.06771 MHz -3 0 5 dB Ch. 700 / 1842.86771 MHz -3 0 5 dB Ch. 791 / 1861.06771 MHz -3 0 5 dB Ch. 870 / 1876.86771 MHz -3 0 5 dB Ch. 885 / 1879.86771 MHz -3 0 5 dB Ch. 908 / 1884.46771 MHz -10 -1 5 dB Ch. 496 / 1927.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 12. If the values are within the limits, click "Save & Continue". 13. Repeat the steps 4 to 10 for GSM1800 and GSM1900. Results Page 7 –32 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Rx AM suppression (GSM) Context Rx AM suppression is used to tune the AM suppression capabilities of the GSM receiver. AM suppression is related to ability of the receiver to operate when there is a disturbing AM modulated signal near the received channel signal frequency. RFIC has tunable compensation circuit which has an effect on the AM suppression ability.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Modulation signal 50 kHz sinewave (or 15 kHz if 50 kHz is not available) 7. Click OK. 8. Check that RSSI level value is between the limits presented in the following table. Table 11 RSSI level values Band 9. Min Max Unit GSM850/GSM900 -115 -90 dB GSM1800 -115 -85 dB GSM1900 -115 -100 dB To proceed to the next band, click "Next". Page 7 –34 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 10. To end the tuning, click "Finish" and "Close". GSM transmitter tunings Tx IQ tuning (GSM) Context • The Tx path branches to I and Q signals at RF I/Q modulator. Modulator and analog hardware located after it cause unequal amplitude and phase disturbance to I and Q signal paths. Tx IQ tuning balances the I and Q branches. • Tx IQ tuning must be performed on all GSM bands. Steps 1.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 5. When the values have been written to the phone memory, click Next to change to the next band. 6. When all bands have been tuned, click Finish and Close to end the tuning procedure. Next actions Tuning sliders should be close to the center of the scale after the tuning and within the limits specified in the following table. If they are not within the limits, check Tx IQ quality manually.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Phase Nokia Customer Care Min Typ Max Unit 95 100 110 dB Tx power level tuning (GSM) Context Because of variations at IC process and discrete component values, the actual transmitter RF gain of each phone is different. Tx power level tuning is used to find out mapping factors called 'power coefficients’. These adjust the GSM transmitter output power to fulfill the specifications.
Nokia Customer Care 6. RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Click Start. Page 7 –38 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide 7. Nokia Customer Care Adjust power levels 5, 15 and 19 to correspond the "Target dBm" column by pressing + or – keys. Check that the coeffiecient values are within the limits specified in the following table. Min Typ Max 0.45 0.626 0.73 GSM850/GSM900 EDGE off PL5 coefficient PL15 coefficient 0.234 PL19 coefficient 0.12 0.195 0.3 0.35 0.419 0.6 GSM850/GSM900 EDGE on PL8 coefficient PL15 coefficient PL19 coefficient 0.247 0.12 0.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care PL15 coefficient Min Typ Max 0.12 0.194 0.3 0.45 0.482 0.7 GSM1900 EDGE off PL0 coefficient PL11 coefficient 0.218 PL15 coefficient 0.12 0.184 0.3 0.35 0.377 0.6 GSM1900 EDGE on PL2 coefficient PL11 coefficient 0.23 PL15 coefficient 0.12 0.193 0.3 8. If the values are within the limits, click "Save & Continue" to proceed to the next band and click Start. 9. Set Edge mode on and start tuning again.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 5. Setup the signal generator to correspond the values in the RX AGC Calibration pop-up window and click OK. Frequency: 2141MHz Level: –51 dBm + cable and adapter attenuations Modulation: FM Deviation: 500 kHz Modulation frequency: 50 kHz 6. Check that the Rx chain value in Tuning Results is within the limits presented in the following table. Min Typ Max Unit RX chain -6 1.5... 3.5 6 dB Low freq -5 -0.7... 4.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Steps 1. From the Operating mode drop-down menu, set mode to Local. 2. Choose Tuning→WCDMA→Rx Band Response Calibration. 3. Click Start and Tune. 4. Setup the signal generator to correspond the values in the pop-up window: Frequency: 2113.4 MHz Level: –48 dBm + cable and adapter attenuations Modulation: FM Deviation: 500 kHz Modulation frequency: 50 kHz 5. Click OK. 6. Change frequency to 2166.6 MHz and click OK. 7.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care i If the values are OK, click Yes to save the values. 8. Close the tuning window. Alternative steps • From the Operating mode drop-down menu, set mode to Local. • Choose Tuning→WCDMA→Rx AGC Alignment. • Click Start. • Check the Tune Rx Band Response check box and click Tune. • Setup the signal generator according to the values in the pop-up window: Frequency list: 2113.4 MHz, 2141 MHz and 2166.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Min Typ Max Unit Rx chain -6 1.5... 3.5 6 dB Low freq -5 -0.7...4.0 5 High freq -5 -0.7...4.0 5 • If the Rx gain is acceptable, click Yes to save the results to the phone. • To end the calibration, click Close.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide 5. Set up the spectrum analyzer in the following way: 6. After setting the spectrum analyzer, click OK. 7. Measure the power levels with a marker. Nokia Customer Care Take the first measurement from 250 us after the trigger, the second from 750 us, the third on 1220 us and so on in every 500 us until the table is filled. Note: It must be possible to measure power levels down to –68 dBm. The measured power levels must be monotonously decreasing.
Nokia Customer Care Page 7 –46 RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide 8. Fill in the power level values (in dBm) to the Wide Range table. 9. In the Wide Range pane, click Calculate. Nokia Customer Care 10. In the High Burst pane, click Tune. 11. Adjust the spectrum analyzer according to the following settings: Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care 12. Measure the power levels with a marker. Take the first measurement from 250 us after the trigger, the second from 750 us, third on 1220 us and so on in every 500 us until the table is filled. Figure 66 High burst measurement 13. In the High Burst pane, click Calculate. 14. Check that the calculated values are within the limits specified in the following table: Min Max C0-high -0.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Min Max Det-k 100 220 Det-b 0 150 15. To save the coefficients to the phone, click Write. 16. To close the Tx AGC & Power Detector window, click Close. 17. Choose Testing→WCDMA→ Tx Control. 18. Select the Algorithm mode tab. 19. Write the target power level 25 dBm to the Start level line and check the Max power limit check box (detector calibration check). 20.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Average: No Trigger: Free run 21. Click Send. 22. Measure the WCDMA output power. It should be around 21 dBm. 23. Click RF Stop and uncheck the Max power limit check box. 24. Repeat steps 19 to 23 for levels +19, +7, 0, -20 and –40 dBm. The measured output power may not differ more than +-2 dB from the requested value at level +19 dBm and no more than +-4 dB on lower levels. Remember to stop the RF before sending new data.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide 3. From the Operating mode drop-down menu, set mode to Local. 4. Choose Tuning→WCDMA→Tx Band Response Calibration . 5. Click Start. Nokia Customer Care The current values are shown in the Tuned Values pane. 6. Click Tune. 7. Connect the power meter to the terminal, and set it to Channel Mid frequency. 8. Read the values of slot 0 and slot 1 from the power meter and enter them to Middle power level fields in the Measured Power Levels pane.
RM-10;RM-24 RF Troubleshooting and Manual Tuning Guide Nokia Customer Care Min Tx Freq Comp (the first and last value) -4 Max +4 17. To save the tuned values to the terminal, click Write. 18. Close the Tx Band Response Calibration window. Tx LO leakage (WCDMA) Context The purpose of Tx LO leakage tuning is to minimize the carrier leakage of the IQ-modulator which is caused by the DC offset voltages in the Tx IQ-signal lines and in the actual IQ modulator.
Nokia Customer Care 8 — Camera Module Troubleshooting Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care (This page left intentionally blank.) Page 8 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Table of Contents Introduction to camera module troubleshooting...............................................................................................8–5 The effect of image taking conditions on image quality...................................................................................8–6 Camera construction..............................................................................................................................
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care (This page left intentionally blank.) Page 8 –4 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Introduction to camera module troubleshooting Background, tools and terminology Faults or complaints in camera operation can be roughly categorised into three subgroups: 1 Camera is not functional at all; no image can be taken. 2 Images can be taken but there is nothing recognizable in them. 3 Images can be taken and they are recognizable but for some reason the quality of images is seriously degraded.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Sensitivity Camera module's sensitivity to light. In equivalent illumination conditions, a less sensitive camera needs a longer exposure time to gather enough light in forming a good image. Analogous to ISO speed in photographic film. Sharpness Good quality images are 'sharp' or 'crisp', meaning that image details are well visible in the picture.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Figure 68 Blurring caused by shaking hands Movement in bright light If an image is taken of moving objects or if the device is used in a moving vehicle, object 'skewing' or 'tilting' may occur. This phenomenon is fundamental to most CMOS camera types, and usually cannot be avoided. The movement of camera or object sometimes cause blurring indoors or in dim lighting conditions because of long exposure time.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Figure 70 Noisy image taken in +70 degrees Celsius Phone display If the display contrast is set too dark, the image quality degrades: the images may be very dark depending on the setting. If the display contrast is set too bright, image contrast appears bad and "faint". This problem is solved by setting the display contrast correctly. This is normal behaviour; do not change the camera module.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Figure 72 Flicker in an image; object illuminated by strong fluorescent light Bright light outside of image view Especially the sun can cause clearly visible lens glare phenomenon and poor contrast in images. This happens because of undesired reflections inside the camera optics. Generally this kind of reflections are common in all optical systems. This is normal behaviour; do not change the camera module.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Examples of good quality images Figure 74 Good image taken indoors Figure 75 Good image taken outdoors Camera construction This section describes the mechanical construction of the camera module for getting a better understanding of the actual mechanical structure of the module. Page 8 –10 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Figure 76 Camera module cross section and assembly principle Figure 77 Camera module bottom view including serial numbering The camera module as a component is not a repairable part, meaning that the components inside the module may not be changed. Cleaning dust from the front face is allowed only. Use clean compressed air. The camera module uses socket type connecting. For versioning, laser marked serial numbering is used on the PWB.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care • • • • Laser-marked serial numbering on PWB (for versioning) Passive components Camera protection window; part of the phone cover mechanics Dust gasket between the lens unit and camera protection window Image quality analysis Testing for dust in camera module Symptoms and diagnosis For detecting dust problems, take an image of a uniform white surface and analyse it in full resolution.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care If dust particles are found on the sensor, this is classified as a manufacturing error of the module, and the camera should be replaced. Any particles inside the cavity between the protection window and the lens have most probably been trapped there in the assembly phase at a Nokia factory. Unauthorized disassembling of the product can also be the root of the problem.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care It should be noted that the effects of any dirt in images can vary much. It may be difficult to judge whether the window has been dirty or if something else is wrong. Therefore, the cleanness of the protection window should always be checked and the window should be wiped clean with a suitable cloth.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Camera troubleshooting flowcharts Camera hardware failure message troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Camera baseband hardware troubleshooting Troubleshooting flow Page 8 –16 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Front camera viewfinder troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Camera Module Troubleshooting Nokia Customer Care Front camera bad image quality troubleshooting Troubleshooting flow Page 8 –18 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care 9 — System Module Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care (This page left intentionally blank.) Page 9 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care Table of Contents Baseband description............................................................................................................................................9–7 System module block diagram........................................................................................................................9–7 Baseband functional description....................................................................................................
RM-10;RM-24 System Module Nokia Customer Care Introduction to receiver functionality...........................................................................................................9–35 WCDMA receiver functionality........................................................................................................................9–35 GSM receiver functionality..............................................................................................................................
RM-10;RM-24 System Module Nokia Customer Care Figure 103 Charger connector.............................................................................................................................9–31 Figure 104 Display connector pin order (top view)..........................................................................................9–33 Figure 105 GSM transmitter.................................................................................................................................
RM-10;RM-24 System Module Nokia Customer Care (This page left intentionally blank.) Page 9 –6 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care Baseband description System module block diagram The device consists of two separate main modules: transceiver (1em) and Flip (1ff). The transceiver board consists of baseband and RF components. Figure 82 System level block diagram Baseband functional description Digital baseband consists of ISA based modem and SYMBIAN based application sections. Modem functionality is in RAP and application processor acts as a platform for SYMBIAN applications.
RM-10;RM-24 System Module Nokia Customer Care Application section includes the application processor ASIC with DDR/NAND combo memory as the core. Stacked DDR/NAND application memory has 512Mbits of DDR memory and 512Mbits of flash memory. The application processor uses 19.2MHz clock, which comes from the RAP divided by two from the 38.4 MHz system clock.
RM-10;RM-24 System Module Nokia Customer Care Section Description DSP subsystem based on a TMS320C55x™ DSP core, which is responsible for intensive data computing tasks like real-time audio and video handling on application side, e.g. voice recording. Internal memory subsystem composed of a single port SRAM. Secure modules These components enable the system to support secure applications. Memory interfaces The memory interfaces define the system memory access organization of application processor.
RM-10;RM-24 System Module Nokia Customer Care Mode Description RESET RESET mode is a synonym for start-up sequence. RESET mode uses 32 kHz clock to count the REST mode delay (typically 16 ms). SLEEP SLEEP mode is entered only from PWR_ON mode with the aid of SW when the system’s activity is low. There are in principle three different sleep modes: • Application processor sleep • RAP sleep • Application processor and RAP sleep (deep sleep) FLASHING FLASHING mode is for SW downloading.
RM-10;RM-24 System Module Nokia Customer Care Power distribution Figure 84 Power distribution diagram Power supply components: • • • • • • EM ASIC (N2200) EM ASIC (N2300) Application processor VCORE SMPS BT LDO backlight SMPS All the above are powered by the main battery voltage. Battery voltage is also used on the RF side for power amplifiers (GSM PA & WCDMA PA) and for RF ASICs Hinku (Rx) & Vinku(Tx). Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care Discrete power supplies are used to generate 2.8V to BT, 1.5V for the LCD controller voltage, 1.3V/1.5V for Application processor and 18V for the backlight LEDs. The device supports both 1.8V/3V SIM cards which are powered by EM ASIC (N2200) / VSIM1. EM ASIC (N2200) s VSIM2 is used to power RS MMC 1.8V only. USB accessories which needs power from the device are powered by EM ASIC (N2300) / VOUT.
RM-10;RM-24 System Module Nokia Customer Care Figure 85 WLAN and BT block diagram WLAN signals and interfaces WLAN interface signals are listed in following table. These signals can be grouped to following categories: host interface 6 lines, clocking interface 3 lines, WLAN/BT coexistence interface 4 lines and power 2 lines. The serial interface is connected to APE McBSP interface block.
RM-10;RM-24 System Module Nokia Customer Care Figure 86 Interconnections between the application processor, power ASIC and IR module Pin 1 Name I/O (IR module) LEDA Connection Battery voltage VBAT Description IR TX LED anode from VBAT through load resistor 2 TxD I Application processor ETMPkt4 Transmit data input to IR Module 3 RxD O Application processor ETMPkt3 Received data output from IR Module 4 SD I Application processor ETMPkt1 Shut Down 5 VCC EM ASIC (N2200) VAUX IR Mo
RM-10;RM-24 System Module Nokia Customer Care Figure 87 SIM interface The EM ASIC handles the detection of the SIM card. The detection method is based in the BSI line. Because of the location of the SIM card, removing the battery causes a quick power down of the SIM IF. The EM ASIC SIM1 interface supports both 1.8 V and 3.0 V SIM cards. The SIM interface voltage is first 1.8 V when the SIM card is inserted, and if the card does not response to the ATR a 3 V interface voltage is used.
RM-10;RM-24 System Module Nokia Customer Care Figure 89 MiniSD contact area and pin order Pin Signal I/O Engine connection Notes Reader 1 CD/DAT3 2 CMD 3 VSS1 4 VDD <- Regulator VCCSD 3.
RM-10;RM-24 System Module Nokia Customer Care Pin A4 Signal I/O Engine connection Notes 2DIR <- Application processor MMC2_DATDIR 1 Data direction 1 VEN <- Application processor GPIO41 miniSD regulator enable -> Application processor REG Misc. Battery cover switch Battery interface The battery interface supports the NMP battery interface for the BL-6C battery. This interface consists of three connectors: VBAT, BSI and GND.
RM-10;RM-24 System Module Nokia Customer Care Table 13 Battery IF electrical characteristics Description Parameter Max Unit Operation voltage VIN 4.23 VDC Current rating IIN 0.9 A Flip qwerty keyboard Flip side of the QWERTY keyboard is connected to the application processor via separate microcontroller (COP8). Engine side of the QWERTY keyboard is connected directly to the application processor pins. There are 6 rows and 7 coulumns in the engine qwerty key matrix.
RM-10;RM-24 System Module Nokia Customer Care Table 14 Test points Test point Notes J4400 SDA I2C bidirectional data J4401 SCL I2C clock J4402 VBAT Supply voltage for flip module Bluetooth RF TI BRF 6150 ROM is a low power Bluetooth RF-tranceiver module meeting Bluetooth compatibility standards (Class 2 Bluetooth v1.2 compliant pre-qualified tranceiver system) and has the BTH/WLAN physical coexistence interface for Nokia application.
RM-10;RM-24 System Module Nokia Customer Care Figure 92 BT-WLAN coexistence framework System partitioning Figure 93 BT-WLAN system partitioning Page 9 –20 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care The interface between BRF 6150 and Nokia BB assumes that all higher layers above the HCI (host controller interface) are implemented in Nokia BB and all other layers (BB, Link Manager, Link Control, and component RF) below the HCI are implemented in BRF 6150. Clock signals BRF 6150 requires a system clock, which it uses to derive all its internal timing. The clock may be sinusoidal or square and the frequency tolerance is +/-20 ppm.
RM-10;RM-24 System Module Nokia Customer Care Pin 3 Signal I/O Flip clock <-> GND Engine connection Application processor sda GND Notes I2C clock Flip ground Display and keyboard backlight The device has one LED Driver (SMPS) that is used to drive display and SW keys. Both display LEDs (4pcs) and keyboard LEDs (2pcs) are connected in series. Current adjustment of the driver is done from the display LED branch, and keyboard current also depends on the display brightness.
RM-10;RM-24 System Module Nokia Customer Care Figure 94 ALS HW implementation Table 16 ALS resistor values Symbol Value R1 R2 R3 R4 R5 R6 R7 NTC-res 5 kOhm 15 kOhm 30 kOhm 50 kOhm 470 kOhm 100 kohm 470 kohm 47 kOhm ASICs RAP ASIC RAP ASIC is a 3G Radio Application Processor.
RM-10;RM-24 System Module Nokia Customer Care • Battery voltage monitoring • 32.
RM-10;RM-24 System Module Nokia Customer Care In addition to the audio transducers, the mixed-signal ASIC also provides an output for the dynamic vibra component. All galvanic audio accessories are connected to the system connector. A Bluetooth audio module, which is connected to the RAP ASIC supports Bluetooth audio functionality. There is also a separate application ASIC for Symbian applications.
RM-10;RM-24 System Module Nokia Customer Care Figure 96 Internal microphone circuitry External microphone Galvanic accessories are connected to the system connector. The accessory audio mode is automatically enabled/disabled during connection/disconnection of dedicated phone accessories. External microphone circuitry is biased by N2200 MicB2 bias voltage output.
RM-10;RM-24 System Module Nokia Customer Care Internal speaker The internal speaker is used in Internal HandsFree (IHF) call mode. A dynamic 16 mm speaker is connected to N2200 outputs HFSpP and HFSpN. The IHF amplifier integrated in N2200 is a Digital Pulse Modulated Amplifier (DPMA). Figure 99 Internal speaker circuitry External earpiece All galvanic accessories are connected to the system connector.
RM-10;RM-24 System Module Nokia Customer Care Vibra circuitry The vibra circuitry is used for the vibra-alarm function. The vibra motor is connected to the EM ASIC (N2200) VibraP and VibraN Pulse Width Modulated (PWM) outputs. Figure 101 Vibra circuitry System connector System connector provides a fully differential 4–wire stereo line-level output connection and fully differential 2-wire mono line-level or microphone level input connection.
RM-10;RM-24 System Module Nokia Customer Care Pin #/ Signal name Signal description 4/ Vout DC out Spectral range Voltage/ Current levels Max or nominal serial impedance DC 2.78V 70 mA 100mΩ (PWB+ conn.) 2.5V 90mA 9 / XMIC N Audio in 300-8k Notes 200mW 1Vpp & 2.5-2.78VDC 10 / XMIC P Audio in 300-8k 1Vpp & 2.5-2.78VDC 11 / HEAR N Audio out 20-20k 1Vpp 10Ω 12 / HEAR P Audio out 20-20k 1Vpp 10Ω 13 / HEAR R N Audio out 20-20k 1Vpp 10Ω Not conn.
RM-10;RM-24 System Module Nokia Customer Care Audio signal electrical characteristics Description Parameter Typ Unit Notes XMIC N Audio in 1 Vpp DC Offset 2.5-2.78V XMIC P Audio in 1 Vpp DC Offset 2.5-2.
RM-10;RM-24 System Module Nokia Customer Care Pin Signal I/O Engine connection Notes 4 VDD <- N2200 VSIM2 VSIM2, supply voltage 1.
RM-10;RM-24 System Module Nokia Customer Care Description Parameter Min Max Unit Notes Threshold for charging, rising (N2300) VMSTR+ 2.1 V Typical value Threshold for charging, falling (N2300) VMSTR- 1.
RM-10;RM-24 System Module Nokia Customer Care Display connector and interface connections Figure 104 Display connector pin order (top view) Table 20 Display module electrical interface signals Display Pin No Display I/O Engine Connection Description Signal Name 1 XRES <- Reset,active low 2 HS <- Horizontal sync. 3 VS <- Vertical sync.
RM-10;RM-24 System Module Nokia Customer Care Display Pin No Display I/O Engine Connection Description Signal Name 13 D3 (B3) <- Data bus 14 D1 (B1) <- Data bus 15 SCL <- Serial clock 16 GND 17 VDDI <- Supply voltage for logic (1.8V) 18 VDD <- Supply voltage (2.5/2.
RM-10;RM-24 System Module Nokia Customer Care Back-up battery interface connections and electrical characteristics Table 21 Back-up battery connections Pin name VBack I/O -> Connection N2200, VBack Notes Back-up battery G2200 is connected to N2200 Table 22 Back-up battery electrical characteristics Description Parameter Back-Up Battery Voltage Vback Min 0 Typ 2.5 Max 2.7 Unit V RF description Introduction to receiver functionality Receiver functions are implemented in an RF ASIC.
RM-10;RM-24 System Module Nokia Customer Care Introduction to transmitter functionality Transmitter functions are implemented in an RF ASIC. The ASIC contains a BB frequency low pass filter, which is tunable according to the signal bandwidth of the system in use. In addition, the ASIC contains separate RF paths comprising a final frequency IQ modulator and VGA amplifiers.
RM-10;RM-24 System Module Nokia Customer Care Figure 105 GSM transmitter GSM power control A closed control loop comprise an integrated power detector (in PA module) and an error amplifier. The error amplifier resides in N7501, and it controls the transmitter power of GSM. GSM PA module A single GSM/EDGE PA module contains two separate amplifier chains, one for EGSM900 (and GSM850) and another for GSM1800/1900. Both amplifiers have a battery supply connection and two bias current inputs.
RM-10;RM-24 System Module Nokia Customer Care Frequency mappings EGSM900 frequencies Page 9 –38 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care GSM1800 frequencies Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care GSM1900 frequencies Page 9 –40 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care WCDMA 2100 Rx frequencies Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 System Module Nokia Customer Care WCDMA 2100 Tx frequencies Page 9 –42 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care 10 — Schematics Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care (This page left intentionally blank.) Page 10 –2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care Table of Contents System connector.................................................................................................................................................10–4 RETU, SIM and Audio.............................................................................................................................................10–5 TAHVO.................................................................................................................
RM-10;RM-24 Schematics Nokia Customer Care System connector Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care RETU, SIM and Audio Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care TAHVO Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care RAP3G, Flash and SDRAM Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care OMAP, Combo memory and MiniSD Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care UI Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care WLAN and BT Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care RF part Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care Signal overview Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Nokia Customer Care Component finder Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Schematics Issue 1 Nokia Customer Care COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
Nokia Customer Care Glossary Issue 1 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Glossary Nokia Customer Care (This page left intentionally blank.) Page Glossary–2 COMPANY CONFIDENTIAL Copyright © 2006 Nokia. All rights reserved.
RM-10;RM-24 Glossary Nokia Customer Care A/D-converter Analog-to-digital converter ACI Accessory Control Interface ADC Analog-to-digital converter ADSP Application DPS (expected to run high level tasks) AGC Automatic gain control (maintains volume) ALS Ambient light sensor AMSL After Market Service Leader ARM Advanced RISC Machines ARPU Average revenue per user (per month or per year) ASIC Application Specific Integrated Circuit ASIP Application Specific Interface Protector B2B Boar
RM-10;RM-24 Glossary Nokia Customer Care DPLL Digital Phase Locked Loop DSP Digital Signal Processor DtoS Differential to Single ended EDGE Enhanced data rates for global/GSM evaluation EGSM Extended GSM EM Energy management EMC Electromagnetic compability EMI Electromagnetic interference ESD Electrostatic discharge FCI Functional cover interface FPS Flash Programming Tool FR Full rate FSTN Film compensated super twisted nematic GND Ground, conductive mass GPIB General-purpose
RM-10;RM-24 Glossary Nokia Customer Care LPRF Low Power Radio Frequency MCU Micro Controller Unit (microprocessor) MCU Multiport control unit MIC, mic Microphone MIDP Mobile Information Device Profile MIN Mobile identification number MIPS Million instructions per second MMC Multimedia card MMS Multimedia messaging service NTC Negative temperature coefficient, temperature sensitive resistor used as a temperature sensor OMA Object management architechture OMAP Operations, maintenance,
RM-10;RM-24 Glossary Nokia Customer Care SARAM Single Access RAM SAW filter Surface Acoustic Wave filter SDRAM Synchronous Dynamic Random Access Memory SID Security ID SIM Subscriber Identity Module SMPS Switched Mode Power Supply SNR Signal-to-noice ratio SPR Standard Product requirements SRAM Static random access memory STI Serial Trace Interface SW Software SWIM Subscriber/Wallet Identification Module TCXO Temperature controlled Oscillator Tiku Finnish for Chip, Successor of t