Linda1.
Linda1.book Page 2 Friday, April 12, 2002 8:31 PM Copyright © Nokia Corporation 2000-2002. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation. Bounce and Triple Pop are trademarks of Nokia Corporation.
Linda1.book Page 3 Friday, April 12, 2002 8:31 PM The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you. This product uses certificates for security functionality. More information on Nokia certificates can be acquired from Nokia web pages. DECLARATION OF CONFORMITY We, NOKIA CORPORATION declare under our sole responsibility that the product RAE-5N is in conformity with the provisions of the following Council Directive:1999/5/EC.
Linda1.
Linda1.book Page 5 Friday, April 12, 2002 8:31 PM Table of Contents Introduction...............................................................................1 Getting help..............................................................................................................3 Facts about your communicator ........................................................................5 GSM data transmission.........................................................................................
Linda1.book Page 6 Friday, April 12, 2002 8:31 PM To make a call.......................................................................................................... 42 To answer a call ...................................................................................................... 45 To manage calls ...................................................................................................... 45 Keypad lock ................................................................................
Linda1.book Page 7 Friday, April 12, 2002 8:31 PM To record a call ........................................................................................................73 To make a new call during a call........................................................................73 To make conference calls .....................................................................................74 To transfer calls....................................................................................................
Linda1.book Page 8 Friday, April 12, 2002 8:31 PM To receive a business card ................................................................................... 106 Settings ..................................................................................................................... 107 To create a new contacts database................................................................... 109 Calendar.....................................................................................
Linda1.book Page 9 Friday, April 12, 2002 8:31 PM Messaging ..................................................................................157 Messaging centre....................................................................................................158 Fax...............................................................................................................................166 Mail...........................................................................................................
Linda1.book Page 10 Friday, April 12, 2002 8:31 PM CARE AND MAINTENANCE......................................................255 IMPORTANT SAFETY INFORMATION ......................................257 Glossary......................................................................................
Linda1.book Page 11 Friday, April 12, 2002 8:31 PM FOR YOUR SAFETY Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given in this manual. Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. ROAD SAFETY COMES FIRST Don’t use the communicator while driving. INTERFERENCE All wireless phones may get interference, which could affect performance.
Linda1.book Page 12 Friday, April 12, 2002 8:31 PM ACCESSORIES AND BATTERIES Use only approved accessories and batteries. Do not connect incompatible products. WATER-RESISTANCE Your communicator is not water-resistant. Keep it dry. BACKUP COPIES Remember to make backup copies of all important data. CONNECTING TO OTHER DEVICES When connecting to any other device, read its user’s guide for detailed safety instructions. Do not connect incompatible products.
Linda1.book Page 1 Friday, April 12, 2002 8:31 PM 1. Introduction Congratulations on purchasing the Nokia 9210i Communicator. It is a complete communications tool: it is a wireless phone, messaging device, and a palmtop organiser in one package.
Linda1.book Page 2 Friday, April 12, 2002 8:31 PM 2 Introduction The Nokia 9210i Communicator consists of two parts: the phone and the communicator interface. The phone is on the device cover and the communicator interface is inside the cover, both as shown in Figures 1 and 2. Large colour Active Matrix TFT LCD screen communicator interface Built-in speaker Figure 2 Both these parts use the same information from the memory of the communicator - they are not separate devices.
Linda1.book Page 3 Friday, April 12, 2002 8:31 PM 3 Introduction The phone is designed for making and answering calls quickly. The communicator looks and operates like other Nokia wireless phones, except the earpiece and microphone are at the rear of the device. The phone is switched on and off by pressing the button on the cover. WARNING: Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger.
Linda1.book Page 4 Friday, April 12, 2002 8:31 PM Introduction 4 • This user’s guide explains in more detail how the Nokia 9210i Communicator operates. “General information” identifies the various parts of the communicator and their functions, as well as the common features of the communicator. The rest of this user’s guide deals with the communicator applications and the phone. There is a short glossary of Internet and wireless terms and abbreviations at the back of the user’s guide.
Linda1.book Page 5 Friday, April 12, 2002 8:31 PM Facts about your communicator Network Services The wireless phone described in this guide is approved for use on the GSM 900 / 1800 networks. Dualband/triband is a network dependant feature. Check with your local service provider if you can subscribe to and use this feature. A number of features included in this guide are called Network Services. These are special services that you arrange through your wireless service provider.
Linda1.book Page 6 Friday, April 12, 2002 8:31 PM 6 Introduction Services that need to be subscribed to are typically the short message service, Internet, and fax. After you have subscribed to the service functions, you can then activate these functions as described in this user’s guide. The manual activation commands for various services are not presented in this user’s guide (for example, using the and characters for activating or deactivating services).
Linda1.book Page 7 Friday, April 12, 2002 8:31 PM sticker to the Club Nokia Invitation Card, if supplied in the sales Access codes The Nokia 9210i Communicator uses several access codes to protect against unauthorised use of your communicator and SIM card. The access codes you need most often are: • the lock code to lock up your communicator, and • the PIN code, which is provided with the SIM card. IMPORTANT: The default lock code is 12345.
Linda1.book Page 8 Friday, April 12, 2002 8:31 PM Introduction 8 Contact information Tip: You can synchronise the contact information on your communicator with a corresponding application on a compatible PC. See the PC Suite Guide on the CDROM for details. All contact information that you store in the Contacts application, such as names, addresses, and phone numbers, goes into the Contacts directory.
Linda1.book Page 9 Friday, April 12, 2002 8:31 PM Cell handover As the phone user moves from one network cell to another, the signal strength of the channel drops and the wireless telephone exchange may handover the user to a different cell and frequency, where the signal is stronger. A cell handover may also occur when the user is stationary, due to varying wireless traffic loads. Such handover may cause slight delays in the transmission.
Linda1.book Page 10 Friday, April 12, 2002 8:31 PM Introduction 10 Low signal strength Due to either distance or obstacles, the radio signal strength from a cell site may not be strong or stable enough to provide a reliable data connection for communication. Therefore, to ensure the best possible communication, remember the following points: • The data connection works best when the communicator is in a stationary position.
Linda1.book Page 11 Friday, April 12, 2002 8:31 PM 2. General information This chapter explains how the communicator operates and how to supply power to the communicator. For information on first start-up and setup of your communicator, see the Getting Started Guide. Communicator display Name and icon of application Menu bar Figure 3 Indicator area Search field Scroll bar Command buttons Commands The communicator interface is turned on by opening the cover.
Linda1.book Page 12 Friday, April 12, 2002 8:31 PM General information 12 Tip: When a command is dimmed, it cannot be used. The commands always correspond to the command buttons, as shown in Figure 3. The applications are run in the middle of the display. The indicators show application and system-related information. To move around a selected frame and select items, use the Arrows key at the lower right-hand corner of the keyboard.
Linda1.book Page 13 Friday, April 12, 2002 8:31 PM Dialogs and pages This is a dialog. This is a page. Another page. To go to it, press the Menu key. Use the Arrows key to move within a page. Figure 5 An example of a dialog which contains several pages is shown in Figure 5. Indicators The application icon and application name in the indicator area display the application you are in at the moment, as shown below.
Linda1.book Page 14 Friday, April 12, 2002 8:31 PM General information 14 Application icon Application name Inbox/Outbox Time Signal strength and battery level Call status - You have a voice call, and the handsfree loudspeaker and microphone are on. - A voice call with the handsfree off. The loudspeaker and microphone are muted. - An open data connection, see the Internet chapter on page 131. - The communicator is receiving or sending a fax.
Linda1.book Page 15 Friday, April 12, 2002 8:31 PM Inbox/Outbox - The inbox indicator informs you that you have received a fax, short message, or mail. - The document Outbox contains unsent messages. See ‘Outbox’ on page 161. Battery level - The battery is low and you should recharge it. - The battery is charging. The bar scrolls until the battery is fully charged. The outlet plug icon indicates that the communicator is connected to an external power source. - The battery is fully charged.
Linda1.book Page 16 Friday, April 12, 2002 8:31 PM General information 16 Communicator keyboard Figure 6 In addition to the normal character and number keys, the keyboard has a number of special keys, as shown in Figure 6. Application buttons The buttons at the top of the keyboard start the corresponding applications or open application groups. The buttons are: Desk, Telephone, Messaging, Internet, Contacts, Calendar, Office and Extras.
Linda1.book Page 17 Friday, April 12, 2002 8:31 PM 17 General information To switch to another application or application group, press the corresponding application button. You can even do this during a call. You need not exit an application before starting another. All inactive applications remain in the background until you activate them again. Note: When you open the WWW application, all other applications are closed to reserve memory for WWW.
Linda1.book Page 18 Friday, April 12, 2002 8:31 PM General information 18 Escape (Esc) To cancel an action, you can either press the Esc key or Cancel. Pressing the Esc key also cancels and dismisses a dialog, and dismisses an information note. Tabulator or Tab You can use the Tab (Tabulator) key to move from one frame to another. When writing or editing documents, the Tab key moves the cursor to the next tab stop.
Linda1.book Page 19 Friday, April 12, 2002 8:31 PM Character (Chr) Press the character key to open a character table where you can select special characters. Press the character key together with characters and commands that are shown in green colour on the keyboard to access them. Press the character key, keep it pressed down and tap a letter key to access accented and other special letters. Tip: You can use the character key with other keys to zoom the view and activate or deactivate infrared.
Linda1.book Page 20 Friday, April 12, 2002 8:31 PM General information 20 Enter When the cursor is shown, pressing Enter moves the cursor to the beginning of the next text line or adds a new line. Enter can also be used to open folders, applications, and documents. When a command is underlined, you can press Enter instead of the command button. When information notes are shown, press Enter instead of OK. In options and settings, when a value can be toggled, you may press Enter instead of Change.
Linda1.book Page 21 Friday, April 12, 2002 8:31 PM To charge the battery Note: See important safety information on battery usage on page 22. 1 Connect the charger cable to the bottom of the communicator, as shown in Figure 8. Figure 8 2 Connect the charger to the proper voltage AC wall outlet. While charging is in progress, the battery level indicator scrolls on the phone display. 3 When the battery is fully charged, the bars stop scrolling and four bars are displayed.
Linda1.book Page 22 Friday, April 12, 2002 8:31 PM 22 General information When the battery level is low and only a few minutes of operation time remain, a warning tone will sound, and the message BATTERY IS LOW will be repeated at regular intervals on the phone display. When the charge level becomes too low for operation, the RECHARGE BATTERY message will be displayed, accompanied by a warning tone. If you do not connect the communicator to a charger, the communicator switches itself off.
Linda1.book Page 23 Friday, April 12, 2002 8:31 PM Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste. Note that a new battery’s full performance is achieved only after two or three complete charge and discharge cycles! The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.
General_information_Iss3.doc Page 24 Friday, October 18, 2002 5:37 PM General information 24 Note: The battery does not fit into place if the SIM card is not correctly installed. Do not force the battery into place! Check that you have inserted the SIM card as described in the Getting Started Guide. If the SIM card is incorrectly installed, remove it by pulling it out of the slot, and insert it again. Memory card Tip: To protect the memory card with a password, see ‘To lock a memory card’ on page 210.
General_information_Iss3.doc Page 25 Friday, October 18, 2002 5:37 PM To insert a memory card 1 Close the device cover and make sure that the phone is switched off. If it is on, press . 2 Open the hatch at the back of the communicator, using a minimum of two fingers - one finger on each side of the hatch. 3 Slide the memory card under the memory card holder as shown in Figure 9. Make sure that the gold contacts of the card are facing down.
General_information_Iss3.doc Page 26 Friday, October 18, 2002 5:37 PM General information 26 General features To select several items at once Where multi-selection is available, you can select several items at once. The selected items are highlighted. The commands you use affect all the selected items. Multi-selection works in most lists. To select items one by one, scroll to the item and press and hold down Ctrl. While pressing down Ctrl, scroll to each item you want to select and press the space bar.
General_information_Iss3.doc Page 27 Friday, October 18, 2002 5:37 PM 27 General information To insert special characters from the keyboard There are two ways to insert special characters directly from the keyboard. To insert characters printed on the keys in green, press and hold the Chr key and simultaneously press a key with a special character printed in green.
General_information_Iss3.doc Page 28 Friday, October 18, 2002 5:37 PM General information 28 Shortcut Function Ctrl + b Ctrl + i Ctrl + u Applies bold Applies italics Applies underlining Full screen mode (if available) Deletes files, messages, shortcuts and other items.
General_information_Iss3.doc Page 29 Friday, October 18, 2002 5:37 PM To save files When you close a new file for the first time, or want to save it, you will be asked to enter a name for the file and to identify a folder in which it should be saved. Figure 10 The following commands become available in the dialog: OK - Confirms the name of the document and saves the document. Browse - Opens a dialog in which you can browse for a location where you save your file. Change format - Opens a list of formats.
General_information_Iss3.doc Page 30 Friday, October 18, 2002 5:37 PM General information 30 To send documents In addition to sending messages in the Messaging application, you can also send documents out of the communicator in the applications where the Send function is available on the Menu list. As a fax - You can send the document as a fax. As a mail - You can send the document as a mail message. As a short message - You can send the document as a short message.
General_information_Iss3.doc Page 31 Friday, October 18, 2002 5:37 PM To check spelling Note: You can spell check only English text and words. Tip: Replace all is available only if you have selected Yes in the Replace all dialog. You can check words and text for spelling in the applications where Spell check… is available on the Menu list. To be able to use this function, you first need to install the Spell checker from the CD-ROM found in the sales package of your communicator.
General_information_Iss3.doc Page 32 Friday, October 18, 2002 5:37 PM General information 32 To print You can print various items, such as documents, pictures, faxes, mails, and short messages. Refer to the user’s guide of the printer for detailed safety instructions on the printing device.
General_information_Iss3.doc Page 33 Friday, October 18, 2002 5:37 PM 33 General information When printing via infrared, make sure that the infrared port of the communicator faces the infrared port of the printer. Keep the infrared connection clear. If the connection is obstructed for too long, for example, if something is moved between the infrared sensors or the communicator is moved, printing is interrupted. For details on infrared connection, see page 35.
General_information_Iss3.doc Page 34 Friday, October 18, 2002 5:37 PM General information 34 Tip: A communication type can have one of the following delivery statuses: pending, delivered, failed, sent, not sent, and scheduled. 2 You can now do the following: send a fax or short message to the contact, call the contact, or add the contact to your Contacts directory. Check the command buttons for available options.
General_information_Iss3.doc Page 35 Friday, October 18, 2002 5:37 PM Use a memory card to gain more space for the different applications and files on the CD-ROM. Note: For information on the installable applications, see the Software on CDROM Guide on the CD-ROM. Tip: For more information about PC Suite, see the PC Suite Guide on the CD-ROM. Tip: See the Add on Applications Guide for information on other software available for your communicator.
General_information_Iss3.doc Page 36 Friday, October 18, 2002 5:37 PM 36 General information To transfer data from other devices IMPORTANT! Do NOT use the method described in section ‘To back up and restore data to and from a memory card’ on page 209 to restore data you have backed up with Nokia 9210 Communicator to Nokia 9210i Communicator. Use PC Suite instead.
General_information_Iss3.doc Page 37 Friday, October 18, 2002 5:37 PM 37 General information 2 On each page, press Change to select or deselect the data categories to transfer to the Nokia 9210i Communicator. To select or deselect all items on a page, press Select all or Unselect all. When you are ready, press Done. . 3 In the main view, press Transfer now. Activate the infrared connection on the Nokia 9110/9110i Communicator. The transfer begins. All items are transferred to the Nokia 9210i Communicator.
General_information_Iss3.
Linda1.book Page 39 Friday, April 12, 2002 8:31 PM 39 Phone 3. Phone Front Back Earpiece Phone Microphone Figure 13 With the cover phone you can make, receive, and manage calls, send and receive short messages, search for phone numbers, change profiles and define many settings. For more complicated tasks like sending long DTMF sequences or modifying phone settings, use the Telephone application. See the Telephone chapter, starting on page 69.
Linda1.book Page 40 Friday, April 12, 2002 8:31 PM 40 Phone Selection keys When operating the phone, press keys one at a time. The phone keypad is not functional when the cover of the communicator is open. Switches the phone on and off. Switches between profiles. See ‘Profile settings’ on page 78. Scroll through menus, submenus or settings. If there are no active calls, you can use the scroll keys to browse through the phone book.
Linda1.book Page 41 Friday, April 12, 2002 8:31 PM 41 Phone Warning: Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. To use the selection keys Figure 14 Selection keys are the keys located just below the right and left corners of the cover display. Commands on the display vary according to the situation and previous selections. Example: Pressing the selection key under the text Menu gains access to the menu functions.
Linda1.book Page 42 Friday, April 12, 2002 8:31 PM 42 Phone and bar - The current signal strength at your location. The more bars visible, the stronger the signal. and bar - Battery charge level. The more bars visible, the more charge there is in the battery. - The phone keypad is locked or the lock code is active. - The phone will not ring to notify you of an incoming call. - You have received one or several new voice messages. - You have received one or several new short messages.
Linda1.book Page 43 Friday, April 12, 2002 8:31 PM 43 Phone International calls When making international calls, start by pressing twice quickly. The international call character ‘+’ appears on the display, which informs the network centre to select the international dialling prefix. After this you can enter the country or region code, area code and phone number. Note: Calls described here as international may in some cases be made between regions of the same nation.
Linda1.book Page 44 Friday, April 12, 2002 8:31 PM 44 Phone To speed dial Speed dialling is a handy way to call frequently-used phone numbers. You can define up to eight speed dial numbers in the communicator memory. For information on how to set speed dials, see page 81. Tip: Pressing and holding dials your voice mailbox number. Example: Press 2 if the speed dial location for the phone number is 2.
Linda1.book Page 45 Friday, April 12, 2002 8:31 PM Tip: For an explanation of DTMF tones, see the Glossary on page 266. To answer a call When you receive a call, the phone gives a ringing tone and the text Call flashes on the display. If silent-profile is active, only the keypad and display light will flash. If the caller can be identified, the caller’s name or phone number, and the text Calling, will be displayed. 1 To answer the call, press . If you do not want to answer the call, press .
Linda1.book Page 46 Friday, April 12, 2002 8:31 PM Phone 46 Tip: If you start making a new call during the current call, the current call is put on hold automatically. Hold/Activate - Hold allows you to put the current call on hold. To activate the original call again, select Activate. New call - Puts the active call on hold and dials a new phone number. Send DTMF - Transmits DTMF tones. See ‘To send DTMF tones during a call’ on page 77. End active call - Ends the active call.
Linda1.book Page 47 Friday, April 12, 2002 8:31 PM 47 Phone When the keypad is locked, you can answer calls normally by pressing . During a voice call, the keypad is unlocked and the communicator can be operated in the usual way. After the call, the keypad is automatically locked again. The keypad will be unlocked automatically when the communicator is connected to a car kit. When the communicator is removed from the car kit, without being switched off, the keypad will be locked automatically again.
Linda1.book Page 48 Friday, April 12, 2002 8:31 PM Phone 48 Tip: You can also use the scroll key and OK to select a profile. 1 Press the key on the keypad. 2 Press the key again until the selection frame is on the desired profile. 3 To select the profile, press and hold . To view help Most menu functions are provided with a help text, which gives a brief description of the displayed function. 1 Scroll to the menu function about which you want help. 2 Wait for a few seconds.
Linda1.book Page 49 Friday, April 12, 2002 8:31 PM 49 Phone 4 To return to the previous menu level, press Back. To exit the menu without changing any settings and to return to the stand-by mode, press . To use menu shortcuts All the menus, submenus and settings are numbered. This number is shown in the upper right corner of the display. 1 Press Menu. 2 Key in the index number of the menu you wish to access.
Linda1.book Page 50 Friday, April 12, 2002 8:31 PM Phone 50 MENU 5 INFRARED MENU 6 SIM SERVICES Only available, if supported by your SIM card. Messages (Menu 1) The Short Message Service (SMS) is a network service which enables you to receive and send short messages. Contact your service provider for details. Write message (1-1) In this menu you can write and send a short message. Inbox (1-2) Tip: To change the tone of an incoming SMS message, see ‘Profile settings’ on page 78.
Linda1.book Page 51 Friday, April 12, 2002 8:31 PM Drafts (1-3) In this menu you can view, modify, and send your draft short messages. Sent (1-4) In this menu you can view and modify the short messages you have sent. Cell broadcast (1-5) This network service allows you to receive SMS messages on topics that you have predefined on the communicator interface. See ‘Cell broadcast’ on page 234. For available topics and relevant topic numbers, contact your service provider.
Linda1.book Page 52 Friday, April 12, 2002 8:31 PM Phone 52 Service command editor (1-6) Tip: These requests are also known as USSD commands. In this submenu, you can send service requests, such as activation commands for network services, to your service provider. For more information, contact your service provider. Voice messages (1-7) Listen to voice messages (1-7-1) Tip: To call your voice mailbox quickly, press and hold .
Linda1.book Page 53 Friday, April 12, 2002 8:31 PM 53 Phone Call register (Menu 2) Missed calls (2-1) Lists calls that you have missed. Note: The communicator only registers missed calls when the phone is switched on and within network coverage. Received calls (2-2) Lists calls that you have received. Dialled numbers (2-3) Lists calls that you have dialled. Clear recent call lists (2-4) Select which calls you want to erase. The options are All/Missed/Dialled/Received.
Linda1.book Page 54 Friday, April 12, 2002 8:31 PM Phone 54 Last call duration (2-5-1) Shows the duration of the last outgoing or incoming call in hours, minutes or seconds, for example, 0:02:15. All calls’ duration (2-5-2) Shows the total duration of all calls made and received with any SIM card that you have used with the communicator. Received calls’ duration (2-5-3) Shows the total duration of calls received with any SIM card that you have used with the communicator.
Linda1.book Page 55 Friday, April 12, 2002 8:31 PM Call costs (2-6) This network service allows you to check various call costs. The costs are shown in charging units or units of currency that you have set in Menu 2-6-3-2. The call cost is shown for each SIM card separately. For these settings you need the PIN2 code, the PIN code, or no code at all, depending on your service provider. Contact your service provider for more information.
Linda1.book Page 56 Friday, April 12, 2002 8:31 PM Phone 56 Call cost limit (2-6-3-3) This function allows you to limit the total costs of outgoing calls to a specified number of charging units or units of currency that you have set in Menu 2-6-3-2. To turn the limit on, select On. Key in the cost limit in charging units or currency units. If you define the limit in currency units, you can press or to insert a decimal point.
Linda1.book Page 57 Friday, April 12, 2002 8:31 PM Automatic redial (3-1-2) When this function is selected and you call a number that is busy or does not answer, the phone will attempt to call the number until the call is connected. The maximum number of redials is 10. Press to end the call attempts. Speed dialling (3-1-3) When selected, you can dial phone numbers stored in the speed dial locations by simply pressing and holding the assigned speed dial key.
Linda1.book Page 58 Friday, April 12, 2002 8:31 PM Phone 58 Line for outgoing calls (3-1-7) If your network supports this service, you can have two phone lines in your communicator. You can select which line you want to use for making calls. For more information, see ‘Line selection page’ on page 90. Phone settings (3-2) Clock (3-2-1) You can select whether the time is shown on the display.
Linda1.book Page 59 Friday, April 12, 2002 8:31 PM If you select Manual, the phone will show a list of available networks and you can select the network you wish to use if this network has a roaming agreement with your home network service operator. If no such agreement is in force, the text No access will be displayed and you must select another network.
Linda1.book Page 60 Friday, April 12, 2002 8:31 PM Phone 60 Call barring service (3-3-2) This network service allows you to restrict incoming calls to, and outgoing calls from your phone. You need a barring password to be able to use this function. Contact your network service provider to get a barring password. The options are: Outgoing calls/International calls/International calls except to home country/Incoming calls/Incoming calls when abroad/Cancel all barrings.
Linda1.book Page 61 Friday, April 12, 2002 8:31 PM 61 Phone The access codes may only include the digits 0 to 9. Lock system(3-3-6) In this submenu, you can lock the communicator. Press Select and enter your lock code. The communicator locks immediately. When your communicator is locked, you can make emergency calls to predefined numbers using the cover phone. You can also answer incoming calls and make emergency calls using the Telephone application. All other actions are blocked.
Linda1.book Page 62 Friday, April 12, 2002 8:31 PM Phone 62 Call divert (Menu 4) Tip: The icon is shown in the stand-by mode when you have activated the Divert all voice calls. This network service allows you to direct your incoming voice calls to another phone number when you do not want to be disturbed, or when the phone is switched off or outside the network coverage area. For details, see ‘To divert voice calls’ on page 83.
Linda1.book Page 63 Friday, April 12, 2002 8:31 PM SIM services (Menu 6) In addition to the functions available in the phone, your SIM card may provide additional services that you can access in the menu 6. Menu 6 is shown only if it is supported by your SIM card. The name and contents of the menu depend entirely on the services available.
Linda1.
Linda1.book Page 65 Friday, April 12, 2002 8:31 PM 65 Desk is an application where you can create and manage links to your favourite documents, applications, or third-party software. Main view Desk 4. Desk Tip: Your favourite links can be, for example, certain WWW pages, WAP services, applications, documents, and photo albums.
Linda1.book Page 66 Friday, April 12, 2002 8:31 PM Desk 66 To add a link Tip: To view and change the icon, label or parameters of a link, select the link, press the Menu key, and then select File > Properties…. Tip: You can start writing a note quickly in any application or even during a phone call by pressing the Desk application button twice. 1 Select the program, program group, or other item for which you want to add a shortcut to Desk. 2 Press the Menu key and then select File > Add to Desk.
Linda1.book Page 67 Friday, April 12, 2002 8:31 PM Desk 67 Image file: Press Change to browse for an image. Press Preview to view the image. 3 Press Done. Note: The image file you choose as a background image should be scaled to appear equal to or bigger than the screen size. For details, see ‘Imaging’ on page 231.
Linda1.
Linda1.book Page 69 Friday, April 12, 2002 8:31 PM 5. Telephone You can use the Telephone application to make and receive phone calls, handsfree calls, or conference calls. You can record and redirect calls, use voice mailboxes, and manage settings and profiles. Open the Telephone application by pressing the Tel application button on the keyboard.
Linda1.book Page 70 Friday, April 12, 2002 8:31 PM Telephone 70 To make a call manually Tip: To disable the handsfree mode, press the Menu key, select Settings > Call… > Audio when cover opened and press Change to switch the handsfree mode Off. Tip: To redial the last dialled number you can also press the shortcut keys Chr+Tel. 1 Type the telephone number in the field at the bottom of the main view. 2 Press Call.
Linda1.book Page 71 Friday, April 12, 2002 8:31 PM Figure 17 To call a number in a recent calls list 1 In the main view, press Recent calls. The Dialled calls dialog opens. If you have new missed calls, the Missed calls dialog opens. 2 To see calls from one of the other lists, select a command button on the right of the display. For example, to see a list of received calls, press Received calls. 3 Select a number from the list and press Call.
Linda1.book Page 72 Friday, April 12, 2002 8:31 PM Telephone 72 To answer a call Tip: To adjust the volume of the speaker during an active call, use the Arrows key: pressing > increases the volume, pressing < decreases the volume. Figure 18 Tip: The caller’s name appears in the note if the telephone number is sent with the call, and if the caller’s number is listed in your Contacts directory. 1 When you receive a call and the communicator cover is open, a note about the incoming call appears.
Linda1.book Page 73 Friday, April 12, 2002 8:31 PM You can also create additional voice mailboxes as follows: 1 Contact your network operator for a number to use with an additional voice mailbox. 2 Press the Menu key and select Settings > Voice mailboxes…. 3 When the Voice mailboxes dialog appears, press Add. Type a name and number. To record a call You can record the conversation during a call. Once a call is in progress, press the Menu key and select Call > Record to open the Recorder application.
Linda1.book Page 74 Friday, April 12, 2002 8:31 PM Telephone 74 1 If you already have an active call and a call on hold, drop one of the calls or merge them into a conference call. 2 Press New call and make the new call. The previous call will be put on hold. 3 To switch between calls, use the Arrows key. The active call is framed with a dark line. The command buttons change according to the status of the selected call.
Linda1.book Page 75 Friday, April 12, 2002 8:31 PM 75 Telephone 2 Once the called person has answered, make a call to a second person by pressing New call. The first call is put on hold. 3 Wait until the second person answers the call. 4 To place both persons into a conference call, press Conference call. The display shows a single conference call. Press Conference commands to list the two participants of the conference call. 5 To include another person, press New call. The conference call is put on hold.
Linda1.book Page 76 Friday, April 12, 2002 8:31 PM Telephone 76 2 Select a participant from the list and press Private call. The call is now split into two: the conference call is on hold and the one-to-one call is active. 3 Once you have finished the private conversation, you can return to the conference call by pressing Conference call. Tip: To view log files of all calls, press the Menu key and select Tools > Log. The General log shows all calls, both incoming and outgoing, voice and data.
Linda1.book Page 77 Friday, April 12, 2002 8:31 PM 77 Telephone To send DTMF tones during a call A dual tone multi-frequency tone system is used by all touch-tone telephones. DTMF assigns a specific frequency, or tone, to each key so that it can easily be identified by a microprocessor. DTMF tones allow you to communicate with voice mailboxes, computerised telephony systems, etc. To send DTMF tones during a call, you have two methods: • Type the digits with the communicator keyboard.
Linda1.book Page 78 Friday, April 12, 2002 8:31 PM Telephone 78 Profile settings The profiles are used for grouping the settings of different operating environments of the communicator. In the settings you can modify the profile features. One profile is always in use. To change the profile in use, press the Menu key. Use the Arrows key to select the Profiles icon at the right-hand end of the menu bar and a new profile from the menu list.
Linda1.book Page 79 Friday, April 12, 2002 8:31 PM To create a new profile 1 To create a new profile, press the Menu key, select Settings > Profiles…, and press New. The current values of the General profile are copied to the new profile. 2 To modify the settings of any of the profiles, highlight a profile name and press Edit. A dialog with four pages opens, as shown in Figure 22. For each of the pages, define the following: Figure 22 General page Name: Type the name of the profile.
Linda1.book Page 80 Friday, April 12, 2002 8:31 PM Telephone 80 Ringing type: Choose the ringing type for the ringing tone. The options are Normal/ Ascending/Ring once. Ringing tone: Define the sound for the incoming call. Press Change to choose from sound files provided with the communicator or to browse for other sound files, if available. To record a tone, see page 229. Ringing tone, line 1: and Ringing tone, line 2: Define the sound for incoming calls on two alternate lines, if available.
Linda1.book Page 81 Friday, April 12, 2002 8:31 PM 81 Telephone Other page Play ringing tone for: Allows you to choose which incoming calls will make a ringing sound. The options are All calls/VIP group only/None. If you choose VIP group only, only the calls coming from someone defined as a VIP will ring; see page 109 in the Contacts chapter. All other calls alert on the display with a message, but will not ring. Speed dials Speed dialling is a quick way to call frequently used numbers.
Linda1.book Page 82 Friday, April 12, 2002 8:31 PM Telephone 82 Figure 23 Network services settings Note: Network services may not be provided by all operators. If services are provided, you may have to subscribe to them. Tip: To change voice call diverting or barring settings, the phone must be switched on. Information about the status of these services is stored in the network.
Linda1.book Page 83 Friday, April 12, 2002 8:31 PM Telephone 83 Figure 24 To divert voice calls Voice call diverting allows you to direct your incoming voice calls to another phone number. This is also known as call forwarding. 1 Press the Menu key and select Settings > Network services > Call diverting…. A dialog opens. 2 Choose divert options: Divert all calls — All incoming calls are diverted. Divert if busy — Incoming calls are diverted when you are engaged in another call.
Linda1.book Page 84 Friday, April 12, 2002 8:31 PM Telephone 84 To: — Type the number to which you want to divert the calls. Default voice mailbox — Calls are diverted to your voice mailbox. If you have more than one mailbox, you must choose one from a list shown to you. See page 85 for more information. Off — Turn off the divert. To restrict voice calls To restrict voice calls you use the voice call barring network service.
Linda1.book Page 85 Friday, April 12, 2002 8:31 PM To cancel all call diverts or barrings, press Cancel all. Other network services 1 Press the Menu key and select Settings > Network services > Other services… 2 Other network service settings contains the following options: Network selection — Allows you to change the way a network is selected and also register to another network. You can set the network selection to either Automatic or Manual.
Linda1.book Page 86 Friday, April 12, 2002 8:31 PM Telephone 86 Figure 25 Properties page Define the following options: Name: Type a descriptive name for the mailbox. Number: Type a number for the mailbox obtained from the network service. Note: The type of voice mailbox determines whether you can edit both of these fields. For example, the name and number of a SIM voice mailbox cannot be edited. DTMF tones page DTMF : Define DTMF tones for a voice mailbox not provided with your SIM card.
Linda1.book Page 87 Friday, April 12, 2002 8:31 PM 87 Telephone Audio when cover opened: Determines whether the handsfree mode is selected automatically when you open the cover. Press Change to toggle On/Off. Automatic redial: When this setting is set On and you call a number that is busy or does not answer, the communicator attempts to call the number until the call is connected. Press Change to toggle On/Off. Advanced settings 1 Press the Menu key and select Settings > Advanced….
Linda1.book Page 88 Friday, April 12, 2002 8:31 PM Telephone 88 Currency: Type a maximum of three characters to indicate your choice of currency. You can type numbers or letters. For example, you can type ‘FIM’ for Finnish currency. This field is used with Unit price below and with Show in currency. Unit price: If you use currency to measure call costs, type a decimal number for the price of each charging unit. You must also complete the Currency field above.
Linda1.book Page 89 Friday, April 12, 2002 8:31 PM Telephone 89 Figure 27 Note: The actual invoice for calls and services from your service provider may vary, depending upon network features, rounding-off for billing, taxes and so forth. Fixed dialling page Fixed dialling is a network service which allows you to restrict your calling to a limited set of numbers stored in the SIM card. The service is offered by some network operators.
Linda1.book Page 90 Friday, April 12, 2002 8:31 PM Telephone 90 If you want to change the settings or view the fixed numbers, you are required to enter your PIN2 code. When the service is set to On, press Edit numbers to add, modify, or delete numbers. You are required to enter names and numbers into the fixed dialling list. Note: When Fixed Dialling is set on, calls may be possible to certain emergency numbers in some networks (e.g. 112 or other official emergency number).
Linda1.book Page 91 Friday, April 12, 2002 8:31 PM Flight profile The flight profile prevents you from accidentally turning on the phone in an aircraft. To select the flight profile: 1 In the Telephone main view, press the Menu key, scroll across the menu bar to the Profiles icon , then highlight Flight. 2 Press Select. With the flight profile active, you may do tasks which do not require the use of wireless network.
Linda1.book Page 92 Friday, April 12, 2002 8:31 PM Telephone 92 IMPORTANT! Using your phone while in the air is prohibited. Switch off your phone before boarding an aircraft. The use of wireless telephones in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network and may be illegal. If the aircraft personnel allow use of the communicator interface, you MUST activate the Flight profile.
Linda1.book Page 93 Friday, April 12, 2002 8:31 PM 6. Contacts You can use the Contacts application to create, edit, and manage all contact information, such as phone numbers and addresses. Start the Contacts application by pressing the Contacts application button on the keyboard. The main contacts database is in the communicator’s memory. You can also store contacts in the SIM card and in databases on an attached memory card.
Linda1.book Page 94 Friday, April 12, 2002 8:31 PM Contacts 94 Tip: You can toggle between the two frames with the Arrows or Tab keys. In the left-hand frame, there is a list of contacts in the currently open contacts database. At the top of the list there is your own card and other available contacts databases. Below the list there is a search box for finding entries. In the right-hand frame there is the currently selected contact card.
Linda1.book Page 95 Friday, April 12, 2002 8:31 PM Figure 31 Contacts 95 2 To make a new contact card using a particular template, press the Menu key and select File > New card. You are prompted to choose a template from a list. 3 When the contact card opens, enter information into the various fields. You can fill in the information on your own business card using the same method. See an example in Figure 31. Note: The title of the P.O. Box field is only displayed when editing the fields.
Linda1.book Page 96 Friday, April 12, 2002 8:31 PM Contacts 96 To open a contact card Tip: To copy or move a range of contacts, select the contacts, press the Menu key and select File > More options > Copy to or Move to.. 1 In the Contacts main view, with the left-hand frame highlighted, select a card. 2 Press Open to open the card in a full display view. To move or copy contacts from a SIM card 1 In the Contacts main view, with the left-hand frame highlighted, select the SIM card and press Open.
Linda1.book Page 97 Friday, April 12, 2002 8:31 PM 97 Contacts Notes on using the search field A search checks the most important fields in a contact card. The matching of search criteria is limited to the beginning of words. For example, to search using the characters ‘Ann’ finds ‘Annabel’ but not ‘Joanne’. The search also checks the contents which follow the following characters: '.' (period) or '/' (forward slash) or '@' (‘at’ symbol) or '~’ (tilde).
Linda1.book Page 98 Friday, April 12, 2002 8:31 PM Contacts 98 Tip: If you want to delete a field on all cards based on the same template, it is simpler to delete it from the template attached to the card. See ‘To create or modify templates’ on page 100. 1 Open a contact card. 2 Select the field you want to rename. 3 Press Rename field. A list of alternative names for the field opens. If you are not allowed to rename the field, the Rename field command button is dimmed.
Linda1.book Page 99 Friday, April 12, 2002 8:31 PM To attach a ringing tone You can set a specific ringing tone for each contact card. When that contact calls you, the communicator plays the chosen ringing tone (if the telephone number is sent with the call). 1 Open the contact card. 2 Press the Menu key and select Card > Ringing tone. A dialog showing the current ringing tone of this contact is displayed. 3 Press Change. A list of default sounds is displayed. 4 Select a sound and press Select.
Linda1.book Page 100 Friday, April 12, 2002 8:31 PM Contacts 100 To create or modify templates Tip: Templates do not apply to contact cards in the SIM card, because the layout of a SIM contact card is fixed. Templates define a set of fields which the communicator uses when creating or displaying a contact card. The default template provides a typical range of fields. You can modify the default template.
Linda1.book Page 101 Friday, April 12, 2002 8:31 PM To store DTMF tones DTMF tones are the tones you hear when you press the number keys on the phone keypad. DTMF tones allow you to communicate with voice mailboxes, computerised telephony systems, etc. You can store a sequence of DTMF tones for a contact card. When you make a call to the contact, you can retrieve the sequence. It will save you from re-entering the characters. 1 Open or create a contact card. 2 Press Add field. A list opens.
Linda1.book Page 102 Friday, April 12, 2002 8:31 PM Contacts 102 To create contact groups You can create contact groups to save time by sending e-mails and short messages to all members of the contact group in one action. 1 With the Contacts directory main view displayed, press the Menu key and select File > New group…. A blank group contact card opens. 2 Enter a name for your group. 3 To add contacts to the group, press Add member. A list of contact cards and groups opens.
Linda1.book Page 103 Friday, April 12, 2002 8:31 PM To change group memberships for a contact or a group Figure 34 1 To view or change the groups to which a contact or a group belongs, open the contact card, press the Menu key, and select Card or Group > Belongs to groups. A list opens, showing memberships for the contact or group. 2 To add the card to a new group, press Add to group. A list of contact groups in the current database opens. 3 Select a group and press Add.
Linda1.book Page 104 Friday, April 12, 2002 8:31 PM Contacts 104 To create a SIM contact card You can view the SIM directory by selecting SIM card in the Contacts directory. The contacts in your SIM card are displayed with SIM location numbers, as shown below: Figure 35 1 In the SIM card main view, press New contact. A dialog opens, as shown in Figure 36. If fixed dialling is active, the SIM contents show only your fixed dialling numbers. For more information on fixed dialling, see page 89.
Linda1.book Page 105 Friday, April 12, 2002 8:31 PM Contacts 105 Figure 36 SIM directory options You can sort the contents of the SIM directory in alphabetical order or by memory location. Press the Menu key and select View > Sort by > Name, or Sort by > SIM location. To see a summary of the usage of the SIM database, press the Menu key and select File > Properties. If fixed dialling is active, you can see only information about fixed dialling numbers.
Linda1.book Page 106 Friday, April 12, 2002 8:31 PM Contacts 106 Tip: PC mail and the short message service are explained in the ‘Messaging’ chapter, starting on page 157. If a contact card is sent as a short message, the card is sent in the Sending format defined on page 108. 2 Press the Menu key and select File > Send. In the Send submenu, make a further choice of media: As a mail/As a short message/Via infrared. You may have other sending options if you have installed additional software.
Linda1.book Page 107 Friday, April 12, 2002 8:31 PM A field is displayed if it is recognised; if not, it is ignored. Audio data, in a supported format, is set as the personal ringing tone of the contact (if you choose to add the card to your Contacts directory) To add the received card to your Contacts directory, press Add to Contacts. The card is converted to contact card format. To reject the card, press Delete.
Linda1.book Page 108 Friday, April 12, 2002 8:31 PM 108 Contacts Name display: Allows you to define the display order of names in the Contacts directory main view. The values are First name Last name/Last name, First name. The names will be displayed in the same order in the Telephone application and the cover phone. Default country or region: Concerns the country or region whose address format is used when viewing contact card addresses in various displays in the communicator.
Linda1.book Page 109 Friday, April 12, 2002 8:31 PM 109 Contacts VIP group page VIP group: Allows you to nominate an existing contact card group to be treated as VIP group. You can restrict the ringing of incoming calls so that only calls from a member of a VIP group will ring, the others will not ring. See Profile settings, ‘Other page’ on page 81. To create a new contacts database Contacts databases are created on a memory card. 1 Press the Menu key and select File > More options > New database.
Linda1.
Linda1.book Page 111 Friday, April 12, 2002 8:31 PM 111 Calendar 7. Calendar In the Calendar application, you can create and check your scheduled events, appointments, anniversaries, and birthdays. You can also list things to do and set alarms to all of the calendar entries. You can synchronise your calendar and tasks with Microsoft and Lotus programs when you connect your communicator to a compatible PC.
Linda1.book Page 112 Friday, April 12, 2002 8:31 PM Calendar 112 Tip: You can use the standard clipboard command shortcuts Ctrl + X and Ctrl + V to cut entries and paste them to a different place. Tip: To send a calendar entry to reserve a time in other device calendars, move to the date that contains the entry and select the entry with the Arrows key, press the Menu key and select Send > As a short message or Via infrared • Task entries are for writing down lists and things to do.
Linda1.book Page 113 Friday, April 12, 2002 8:31 PM Tip: To see how attachments are added to an entry, see page 118. Details page Description: The description of the entry. Timed: Specifies whether a day entry is timed or untimed. ‘Timed’ means that the entry has a specific start time, end time, and duration. ‘Untimed’ means that the entry happens on a particular date, but at no specific time. If you select No, you may have to define the date for the day entry in the field below.
Linda1.book Page 114 Friday, April 12, 2002 8:31 PM Calendar 114 Alarm page Tip: You can set an alarm for a task entry only if you have also set a Due date. Set alarm: Specifies whether an alarm is set for the entry. Time before: The time when an alarm set for a timed day entry will go off. Alarm time: The time when an alarm set for an untimed entry will go off. Days before: The number of days before an entry when an alarm will go off.
Linda1.book Page 115 Friday, April 12, 2002 8:31 PM 115 Calendar Repeat on dates: The dates on which the entry is repeated. Use the Arrows key to go to a date you want to select and press Select. You can select more than one date at a time. See Figure 42. Figure 42 Repeat interval: The time period between repeats. Repeat indefinitely: Frequency of the repetition. The options are Yes / No. Note: It is still possible to remove or edit a single entry even if the entry is repeating.
Linda1.book Page 116 Friday, April 12, 2002 8:31 PM Calendar 116 Example: If you are not sure if an entry will take place, you can mark it as Tentative. Tentative: Whether an entry is confirmed or not. A tentative entry is indicated with icon next to the entry text. Crossed out: Whether an entry has been completed or not. Crossing out an entry does not remove it from the calendar.
Linda1.book Page 117 Friday, April 12, 2002 8:31 PM To delete entries You should tidy up your calendar from time to time by deleting entries, since calendar entries accumulate over time and consume memory. Note: You can also back up your calendar data to a compatible PC. See the PC Suite Guide on the sales package CD-ROM for details. To delete a single entry There are two ways to delete a single entry: • Select the entry in the view, then press the backspace key.
Linda1.book Page 118 Friday, April 12, 2002 8:31 PM 118 Calendar Time period: The time scope of the removal. The options are Whole calendar/Until today/From today/Other. Start: The start date of the entries to be removed. End: The end date of the entries to be removed. Entry types page Choose from the following options: Appointments/Events/Anniversaries/Tasks. To view, create, and delete attachments 1 Open a calendar entry by pressing Enter. The entry details dialog with four pages opens.
Linda1.book Page 119 Friday, April 12, 2002 8:31 PM Commands in all views The following command buttons are available in all of the views: Edit - Opens a selected calendar entry for editing. New entry - Enables you to create a new calendar entry if there are no entries for that day. You can also create a new calendar entry by just starting to enter characters on the keyboard, see ‘To create new calendar entries’ on page 112.
Linda1.book Page 120 Friday, April 12, 2002 8:31 PM Calendar 120 Left frame Tip: To edit an event, the right frame must be active. If you are in the left frame, go to the desired date and press the Enter key. The focus moves to the right frame. One row in the day table equals one week. Abbreviations for the days of the week are in the highest row. Tip: To see a list of icons that are displayed in all views, see page 125.
Linda1.book Page 121 Friday, April 12, 2002 8:31 PM The coloured indicator area next to a day box shows the date and name of the day. Today’s indicator area is framed green. Day view Tip: To move the position of the title box from left to right, press the Menu key and select View > View settings…. See Title location in ‘View settings’ on page 129. Figure 45 The day view shows the events for the selected day. Events are grouped into one time slot according to their starting time.
Linda1.book Page 122 Friday, April 12, 2002 8:31 PM Calendar 122 Tip: In day and week views, you can quickly move to a different date by pressing the Tab key, selecting the desired date with the Arrows key, and pressing Enter. Task lists Figure 46 Tip: To see how to-do task lists are created, see page 126. Tip: To see a list of all task lists, press the Tab key. You can create one or several business or personal task lists which may contain tasks with or without deadlines.
Linda1.book Page 123 Friday, April 12, 2002 8:31 PM Weekly time schedule Tip: You can select different bar colours for different types of entries. See ‘Status page’ on page 115. Figure 47 The weekly time schedule shows the reserved hours for the selected week. This means that only timed entries are shown The currently selected time box is framed. Entries are marked with bars. If a time box contains entries, the bar across the bottom of the weekly time schedule shows the details of the entry.
Linda1.book Page 124 Friday, April 12, 2002 8:31 PM Calendar 124 Year schedule Figure 48 The year schedule shows the timetable for the selected year. Only entries with colours are shown in the year schedule. If there are several colours connected to the day, only one can be shown. Abbreviations for the days of the week are in the highest row and the months of the year in the far left column. Time boxes have the same functions as in the Weekly time schedule.
Linda1.book Page 125 Friday, April 12, 2002 8:31 PM Note: Only anniversary entries are shown in the anniversary view. Icons You can see the following symbols in Calendar: - Alarm - Anniversary - Attachment - Event - Repeating entry - Tentative entry - Task - Task, with high importance - Task, with low importance - Untimed entry Tip: To change the number of months shown in the anniversary view, press the Menu key and select View > View settings…. See Months in view in ‘View settings’ on page 129.
Linda1.book Page 126 Friday, April 12, 2002 8:31 PM 126 Calendar Task lists To create a new task list 1 Press the Menu key and select File > New task list…. A dialog with two pages opens. 2 Define the task list on the two pages of the dialog. See ‘Details page’ and ‘Visibility page’ below. 3 When you are ready, press Close. The new task list is added in Task lists. Details page Tip: If you choose to sort a task list manually, all tasks on the list appear numbered.
Linda1.book Page 127 Friday, April 12, 2002 8:31 PM 127 Calendar To delete a task list 1 Open the task list. 2 Press the Menu key and select File > Delete task list. To search for Calendar entries You can search through the entries for particular pieces of texts. 1 Press the Menu key and select Tools > Find entry…. A search field opens. 2 Enter a key word for the entry you want to search for, or press Options to restrict the search by defining a set of qualifications. A dialog with two pages opens.
Linda1.book Page 128 Friday, April 12, 2002 8:31 PM Calendar 128 Figure 50 4 Select an entry and press: • Edit to open the entry details dialog for editing, • Go to to go to the date or view where the entry is located or, • New find to start a new search. 5 Press Close to return to the currently active view. Settings General settings 1 Press the Menu key and select Tools > General settings…. A dialog opens.
Linda1.book Page 129 Friday, April 12, 2002 8:31 PM View settings You can define the appearance of the view and default entry types for each view by following these steps: 1 Go to the view you want to define. 2 Press the Menu key and select View > View settings…. A dialog with two pages opens. 3 Define the view settings on the two pages of the dialog. See ‘Details page’ and ‘Entry types’ below. 4 Press Done to return to the currently active view. Note: The contents of the dialog vary in different views.
Linda1.book Page 130 Friday, April 12, 2002 8:31 PM Calendar 130 Show colour markings: Specifies whether all entry symbols or only symbols with the letter specified in Default colour are shown in the year view. Default colour: The symbols and background colours of the different entry types in the particular view. Months in view: The number of month boxes in the anniversary view.
Linda1.book Page 131 Friday, April 12, 2002 8:31 PM 131 Internet 8. Internet This chapter describes how to get access to the Internet and how to use the Internet applications. When you take your communicator into use, it has the following browser applications: WWW - A World Wide Web (WWW) browser supporting frames, JavaScript, and SSL protocol. WAP - A browser for accessing various types of information, entertainment, and other services in Wireless Application Protocol (WAP) format.
Linda1.book Page 132 Friday, April 12, 2002 8:31 PM Internet 132 Note: You must have your phone turned on, within network coverage and free of any other voice or data call to connect to the Internet. To set up your Internet access point Note: To be able to use the Internet services, you need to configure an Internet connection. Some Internet service providers may offer you the possibility to configure your Internet settings by sending you a smart message via SMS.
Linda1.book Page 133 Friday, April 12, 2002 8:31 PM Ask before connecting: The options are Yes/No. If you choose Yes, a connection dialog appears every time you connect to the Internet, asking you to either confirm, change, or cancel the connection, or change the Internet access point. If you choose No, the communicator will choose the default Internet access point.
Linda1.book Page 134 Friday, April 12, 2002 8:31 PM Internet 134 Figure 52 2 If you already have connections defined, you can use an existing connection as a basis for the new connection. After you have pressed New, press Use existing. Choose the connection you want from the list which appears, and press OK. 3 A dialog on connection details opens. See Figure 53. Note: The exact values for the settings are provided by your ISP. Figure 53 Tip: All your connections should have different names.
Linda1.book Page 135 Friday, April 12, 2002 8:31 PM Figure 54 Proxies page You may want to use a proxy to quicken access to the Internet. Note also that some ISPs require the use of Web proxies. Contact your ISP to determine proxy details. Tip: Often the minimum requirement for an Internet connection is: Phone number, Username, and Password. Internet 135 Password prompt: If you must type in a new password every time you log on to a server, or if you do not want to save your password, choose Yes.
Linda1.book Page 136 Friday, April 12, 2002 8:31 PM Internet 136 When you have made an Internet connection for your company’s intranet, and you are unable to retrieve Web pages from the general WWW, you may need to setup a proxy server to retrieve Web pages outside your company’s intranet. Tip: If you set Use proxy server to No, Port number, Proxy server, and No proxy for are dimmed. Example: Example domain names are: company.com and organisation.org. In a list, separate domain names with semicolons.
Linda1.book Page 137 Friday, April 12, 2002 8:31 PM Modem initialisation: Controls your communicator using modem AT commands. If required, enter characters specified by your GSM network service provider or ISP. Callback page Use callback: This option allows a server to call you back once you have made the initial call, so you have a connection without paying for the call. Contact your Internet service provider to subscribe to this service. The options are Yes/No.
Linda1.book Page 138 Friday, April 12, 2002 8:31 PM Internet 138 Callback type: The options are Use server number/Use server number (IETF)/Use number below. Ask your Internet service provider for the correct setting to use. The setting depends on the service provider’s configuration. Callback number: Type in your communicator’s data phone number which the dial back server uses. Usually, this number is the data call phone number of your communicator.
Linda1.book Page 139 Friday, April 12, 2002 8:31 PM 139 Internet Script options If you need to define script options for your Internet connection, press Script options on the Other page. A script can automate the connection between the communicator and the server. See Figure 57. Note: Scripts are not usually required when you establish a connection. To find out whether you need a script, contact your Internet service provider. Tip: Your Internet service provider may be able to provide you with a script.
Linda1.book Page 140 Friday, April 12, 2002 8:31 PM Internet 140 Address options Tip: There is a glossary containing Internet terms and abbreviations at the back of this user’s guide. Press Address options on the Other page, to define the IP and DNS addresses. See Figure 58. Define the following: Figure 58 Auto retrieve IP address: If you select Yes, the IP address is obtained automatically from the server. The options are Yes/No. This setting is also called ‘dynamic IP address’.
Linda1.book Page 141 Friday, April 12, 2002 8:31 PM To connect to the World Wide Web To connect to the World Wide Web, • the GSM data service must be activated for your SIM card, and • you must configure an Internet access point. See page 132. Note: Only install software from sources that offer adequate protection against viruses and other harmful software. For information on software installation and security certificates, see ‘Certificate manager’ on page 222.
Linda1.book Page 142 Friday, April 12, 2002 8:31 PM 142 Internet connection is made; see ‘Internet connections’ on page 132. To change the Internet access point, press Change connection. Press OK to establish a connection. Figure 60 Tip: An alternative way to disconnect from the Internet is to close the cover and press the key. Note: In order to free up additional memory for large Web pages, all other applications are closed automatically when the WWW browser is opened.
Linda1.book Page 143 Friday, April 12, 2002 8:31 PM Example: An example of a URL address is www.nokia.com Figure 61 2 A dialog with the Connection name and Phone number of the Internet access point you are using is displayed. See Figure 60. You can also choose not to see the connection dialog when the connection is made; see ‘Internet connections’ on page 132. To change the Internet access point, press Change connection. Press OK to establish a connection.
Linda1.book Page 144 Friday, April 12, 2002 8:31 PM Internet 144 Tip: To save page elements in your communicator, press the Menu key, select File > Save, and select the appropriate submenu command. To browse the WWW After the Web page has been retrieved, the following commands become available, depending on what is selected on the page: Open URL- Press to open a dialog where you can define a web page to open. Go to - When a link is selected, press Go to to view the target of the link.
Linda1.book Page 145 Friday, April 12, 2002 8:31 PM To browse with the keyboard The best way to browse a page and the WWW is to use both the keyboard shortcuts and the pointer. You can use the Tab key and some other keys to select elements on a page or the pointer as a mouse to select elements directly. The following table lists useful keyboard shortcuts of the WWW application. You can find more shortcuts in the application next to menu commands.
Linda1.book Page 146 Friday, April 12, 2002 8:31 PM 146 Internet To browse with the pointer You can see the pointer on the screen when you open a web page. The functionality of the pointer is similar to a mouse, but you move it with the Arrows key and click it by pressing the Enter key. To select an area, keep Enter pressed down and move the pointer over the area with the Arrows key. Tip: Press Ctrl + Tab to change the active frame.
Linda1.book Page 147 Friday, April 12, 2002 8:31 PM To change frame sizes Where a Web page contains frames, you can change the frame sizes of the page, to get a better view of the contents of the selected frame. 1 Move the pointer cursor over a frame border. 2 Press and hold down the Enter key. Arrows are displayed around the selected frame border 3 Use the Arrows key to resize the frame. 4 To cancel the previous move, press Esc.
Linda1.book Page 148 Friday, April 12, 2002 8:31 PM Internet 148 Figure 62 General page Show images: The options are Yes/No. If you select Yes the WWW browser loads all the pictures on a Web page when it displays the Web page. Frames options: The options are Show all frames/Show frames one by one/Do not use frames. Some Web pages are split into several frames, which makes reading difficult, so choose an option which suits you.
Linda1.book Page 149 Friday, April 12, 2002 8:31 PM Empty history list on exit: If you select Yes, the history list is emptied when you exit the WWW browser. The options are Yes/No. Cache, History, and Plug-ins view These views display a list of information on cache memory, browser history and installed plug-ins. To view information about the cache memory used for temporary storage of the pages you visit, press the Menu key and select Information > Cache.
Linda1.book Page 150 Friday, April 12, 2002 8:31 PM 150 Internet The Bookmarks view lists links to WWW pages in related folders. You can organise, edit, and view these bookmarks. You can also search for them and then connect to the URL addresses directly. See Figure 63. Figure 63 Tip: To create and rename folders, press the Menu key and select Bookmarks > Insert new folder or Rename folder. To retrieve the currently highlighted Web page, press Go to.
Linda1.book Page 151 Friday, April 12, 2002 8:31 PM To export the Bookmarks list In the Bookmarks view, press the Menu key and select Bookmarks > Export as HTML. to export the current Bookmarks list as a HTML document. Note: When you export bookmarks as HTML, the folder structure is lost. WAP The WAP application can be used to access Internet services which are based on the Wireless Application Protocol (WAP). These services can contain news, weather reports, flight times, dictionaries, and so on.
Linda1.book Page 152 Friday, April 12, 2002 8:31 PM Internet 152 • To access WAP services you need to define WAP access points in your communicator. WAP access points are additional to the Internet settings. You can receive WAP access points directly via a short message from your WAP service provider, or define them manually. This chapter contains instructions for manual setup.
Linda1.book Page 153 Friday, April 12, 2002 8:31 PM Internet 153 Figure 64 3 Press Close when you are ready. Name: Name of the connection. All your connections should have different names. You can define each name freely. Secure connection: Whether the security protocol TLS is used for the connection. The options are Yes/No. Follow the instructions given to you by your WAP service provider. See also Glossary term ‘Transport Layer Security’ on page 272.
Linda1.book Page 154 Friday, April 12, 2002 8:31 PM 154 Internet 2 Press Change to change the connection. A list opens. 3 Choose the connection from the list and press OK. Bookmarks The Bookmarks view is the main view of the WAP application. You can organise, edit, and view these bookmarks in the same way as WWW bookmarks, see page 149. Tip: The shortcut to add a bookmark is Ctrl + B. To add a bookmark, press the Menu key, then select Bookmarks > Add bookmark. A dialog opens. See Figure 65.
Linda1.book Page 155 Friday, April 12, 2002 8:31 PM 155 There are three ways to open a WAP page, either: • Choose a WAP bookmark from the list of bookmarks and press Go to. The page is retrieved; or • Go to the WAP application home page. Press the Menu key, then select Go to > Home page. For more information on defining the WAP home page, see ‘WAP settings’ on page 155; or • Open a URL; press the Menu key, then select File > Open page. A dialog opens. Enter the address of the URL, for example: mobile.club.
Internet.doc Page 156 Tuesday, April 16, 2002 6:38 PM Internet 156 Figure 66 Here you can change settings such as your WAP home page. NOTE: You can use a file on the communicator as your home page. Java The Java in the Nokia 9210i Communicator is a Personal Java application environment designed especially for the communicator. Java enables you to use Java applications downloaded from the Internet. Java Software Development Kit (SDK) is available in Forum Nokia.
Linda1.book Page 157 Friday, April 12, 2002 8:31 PM 157 Messaging 9. Messaging Messaging contains the following applications: Fax, Mail and SMS (Short Message Service). To start Messaging, press the Messaging application button on the communicator keyboard. The overall requirements for using fax, mail and SMS, applications are as follows: • The phone must be turned on. • The network you are using must support fax calls, data calls, and the Short Message Service.
Linda1.book Page 158 Friday, April 12, 2002 8:31 PM 158 Messaging Messaging centre Figure 67 Tip: You can move between the two frames with the Arrows or Tab key. The main view of Messaging has two frames: on the left is a list of the folders in the Messaging centre, and on the right are the messages connected to the currently selected folder. Folders in the Messaging main view are: Inbox - Received faxes and short messages. Received mail appears in the Remote mailbox folder.
Linda1.book Page 159 Friday, April 12, 2002 8:31 PM Tip: You can also press Enter to open messages and folders. To manage folders You can create your own folders in Drafts, in your own folders and in the root of the folder list. You cannot create new folders in Inbox, Outbox or Sent. 1 2 3 4 5 Select the left frame in the main view of the Messaging. Press the Menu key and select File > Folder > Create new folder…. Type a name for the new folder. Select where you want to create the folder. Press Create.
Linda1.book Page 160 Friday, April 12, 2002 8:31 PM Messaging 160 Tip: To choose the sorting order, press the Menu key and select View > Sorting order. Choose between Ascending and Descending. 1 Open the folder where you want to sort the messages and faxes. 2 Press the Menu key and select View > Sort by. 3 Choose from the following options: Message type/Sender/Recipient/Subject/Date/ Size/Priority. Inbox Figure 68 Tip: To reply to a message in the Inbox, press the Menu key and select Write > Reply.
Linda1.book Page 161 Friday, April 12, 2002 8:31 PM 161 Messaging new ringing tone new remote configuration data unread mail unread mail received from PC by synchronisation priority high priority low message contains an attachment Outbox Figure 69 Statuses Faxes, mail and short messages waiting to be sent from the communicator can have the following statuses in Outbox: Sending - The fax or short message is currently being sent.
Linda1.book Page 162 Friday, April 12, 2002 8:31 PM 162 Messaging Waiting - The fax or short message is queuing to be sent and will be sent as soon as possible, for example, when the phone is switched on, signal strength becomes adequate, or the previous phone call ends. In the case of mail messages, Waiting shows that the message will be sent the next time you connect to your remote mailbox. Calling… - Outbox is calling the recipient of the fax message. Preparing...- Outbox is rendering a T.
Linda1.book Page 163 Friday, April 12, 2002 8:31 PM You can also send faxes, mail and short messages in all the applications where you can find the option File > Send after pressing the Menu key. If you want to save, but not send a fax, mail or short message you have just written in the corresponding editor, press Close. The message is saved in the Drafts folder. The saved message replaces the previously saved version of the same message.
Linda1.book Page 164 Friday, April 12, 2002 8:31 PM Messaging 164 Tip: You can select more than one contact at a time, see ‘To select several items at once’ on page 25. Tip: In the case of mail, you need to select the contacts to the appropriate fields in the dialog by pressing To, Cc or Bcc. 2 Search for a contact or contacts in the left frame and press Select. The right frame shows the contacts you have already selected; to remove a contact, select it and press Remove. 3 Press Done.
Linda1.book Page 165 Friday, April 12, 2002 8:31 PM To delete dowloaded mail messages from the communicator: 1 Press the Menu key in the main view of Messaging and select Tools > Message storage…. A dialog with two pages opens. 2 On the Communicator page you can choose to delete all mail messages or messages older than a given time period. To delete selected messages, press Delete now. Messages are deleted from your communicator’s memory, but they are not deleted from your remote mailbox.
Linda1.book Page 166 Friday, April 12, 2002 8:31 PM Messaging 166 Fax Tip: For more advanced word processing, use Word Processor instead of the fax editor. You can write and send faxes in the fax editor. You can write documents in the Word Processor or Sheet applications and then send them as faxes. It is also possible to send faxes with embedded images. For details on images, see ‘Imaging’ on page 231. To write and send a new fax 1 Press Write fax in the main view of Messaging.
Linda1.book Page 167 Friday, April 12, 2002 8:31 PM Fax cover page You can attach a cover page to the fax you are currently creating or editing. 1 Press Sending options and then select Fax cover page. 2 Choose one of the following options: None: The header of the fax will have only the To: and Fax number: fields. Header: The header of the fax will have information about the sender and recipient of the fax, and the date of the fax.
Linda1.book Page 168 Friday, April 12, 2002 8:31 PM Messaging 168 To select and save all or part of a received fax You can select all or part of a fax and save it in another format for further editing. To select an area of a fax page 1 Press the Menu key in the fax viewer and select Tools > Selection frame. A selection frame appears in the fax viewer. 2 Use the arrows key to move the selection frame to the upper-left corner of the area you want to select.
Linda1.book Page 169 Friday, April 12, 2002 8:31 PM To retrieve faxes from a remote fax box 1 Press the Menu key in the main view of Messaging and select Receive > Fax > Dial fax poll. 2 Type in the fax number for the remote fax box, or choose the number by pressing Recipient. 3 Press Call to call the number. Fax settings Any changes you make to fax settings affect the way in which your faxes are sent and received. 1 Press the Menu key in the main view of Messaging and select Tools > Account settings….
Linda1.book Page 170 Friday, April 12, 2002 8:31 PM 170 Defines whether or not the Error Correction Mode is used when faxes are sent. If set to On, any pages containing errors are automatically returned to sender, until the defects are corrected. The options are On/Off. Resend: Defines which pages will be sent again if the fax sending has failed. The options are All pages/Missed pages.
Linda1.book Page 171 Friday, April 12, 2002 8:31 PM Figure 72 4 Define the following: General page Mail account name: The name of the remote mailbox. You can type here any name to describe the mailbox. My name: Type in your name. Username: Type in your user name. Password: Type in your password. If you leave this field blank, you will be prompted for a password when you try to read mail in your remote mailbox. My mail address: Type in the mail address given to you by your service provider.
Linda1.book Page 172 Friday, April 12, 2002 8:31 PM 172 Messaging Internet access: The IAP connection used for the mailbox. Choose an IAP from the list. To create an IAP, see ‘To set up your Internet access point’ on page 132. Default account: Choose a mail account from the list. When you set up an account for the first time, it will be the default until more accounts are created.
Linda1.book Page 173 Friday, April 12, 2002 8:31 PM Advanced page Default mail type: The type of mail that you can write and send from your communicator. The options are Plain text (no MIME)/Plain text/Formatted text (HTML). Send mail: How mail is sent from your communicator. The options are Immediately/ During next connection/Upon request. Include signature: Specifies whether your signature is attached to sent mail. The options are No/Use my contact card/Custom.
Linda1.book Page 174 Friday, April 12, 2002 8:31 PM 174 Messaging IMAP4 folder path: Define the location of the IMAP mail folder here, if not defined automatically. This option is available only if the mailbox type is IMAP4. To edit an account 1 Press the Menu key in the main view of Messaging and select Tools > Account settings…. A list of accounts opens. 2 Select the account you want to edit and press Edit. 3 Define the settings on the General, Servers, Retrieve and Advanced pages explained above.
Linda1.book Page 175 Friday, April 12, 2002 8:31 PM Recipients Messaging 175 3 Press Recipient to select the recipient or recipients of the message, or type in the name or mail address into the To:, Cc: and Bcc: fields. You can move from one insertion field to another by pressing the Tab key. 4 If you wish to adjust the sending options of the mail message, press Sending options. A dialog with two pages opens, see page 176. 5 Press Send.
Linda1.book Page 176 Friday, April 12, 2002 8:31 PM Messaging 176 Tip: To format the font for a selected text area, press the Menu key and select Format > Font…. To set a preferred font for plain text and HTML mail, press the Menu key and select Tools > Preferences…. To align a mail message, press the Menu key and select Format > Alignment. This opens the following options: Left, Centre and Right.
Linda1.book Page 177 Friday, April 12, 2002 8:31 PM 177 Messaging Send mail: When the message will be sent. The options are Immediately/Upon request/During next connection. To retrieve mail Mail addressed to you is not automatically received by your communicator, but by your remote mailbox. To read your mail, you must first connect to the remote mailbox and then select the messages you wish to retrieve into your communicator. Connection to a remote mailbox is established via a data call.
Linda1.book Page 178 Friday, April 12, 2002 8:31 PM 178 Messaging To subscribe and unsubscribe to remote mailbox folders If your remote mailbox is of IMAP4 standard, you can edit and synchronise remote inbox folders in your communicator. To do this, you need to subscribe to the folders and make them visible in your communicator. Tip: To create new folders in your remote mailbox, go online, press the Menu key and select File > Folder. You can now choose whether to Create new folder… or Rename folder….
Linda1.book Page 179 Friday, April 12, 2002 8:31 PM 179 Messaging WARNING! Messages marked as deleted when offline will also be deleted from the remote mailbox server, when online. To delete local mail messages without deleting remote mailbox files, see ‘To avoid low memory’ on page 164. To reply to mail 1 Select the mail message in Inbox and press Open. The mail viewer opens. 2 Press Reply. The mail editor opens.
Linda1.book Page 180 Friday, April 12, 2002 8:31 PM 180 Messaging Mail attachments You can send most documents and messages you write in the other applications of your communicator as mail attachments. WARNING! Mail attachments may contain viruses or they can otherwise be harmful to your communicator or PC. Do not open any attachment, if you are not sure of the trustworthiness of the sender.
Linda1.book Page 181 Friday, April 12, 2002 8:31 PM Working online and offline Working online means working with your communicator connected to a remote mailbox via Internet connection. When you work offline which means that your communicator is not connected to a remote mailbox, you can delete only messages, not folders. When online, you can delete, rename or create new folders in your remote mailbox.
Linda1.book Page 182 Friday, April 12, 2002 8:31 PM Messaging 182 Mail synchronisation with your PC Synchronisation is the process of making the contents of your mail messages and mail folders identical on both your communicator and your PC. This is done by copying and combining information between the two machines. For more information, see PC Suite Guide on the sales package CD-ROM.
Linda1.book Page 183 Friday, April 12, 2002 8:31 PM To convert to PC or Internet mail Note: HTML messages cannot be converted since PC mail does not support the sending of HTML messages. You must change the message type to plain text or non-MIME type in the Sending options dialog, before you can convert the message to PC mail. See page 176 for more information. PC and Internet mail appear together in the folders. 1 Select the mail message or messages you wish to convert.
Linda1.book Page 184 Friday, April 12, 2002 8:31 PM 184 Messaging Note: If you want to send text you have written or edited in another application as a short message, all embedded objects or any rich formatting will be lost. You cannot send attachments as short messages, either. To write and send a new short message Note: You cannot change the font, style or format of short messages.
Linda1.book Page 185 Friday, April 12, 2002 8:31 PM Tip: To define a specific date and time when the short message will be sent, select Scheduled in the Send short message option. To receive and read short messages Short messages are received automatically, provided that this service is available and that the phone is on and within network coverage. When a new short message arrives, a tone will sound - unless the device is set to a silent profile - and an information note is shown on the display.
Linda1.book Page 186 Friday, April 12, 2002 8:31 PM 186 Messaging SMS settings Any changes you make to SMS settings affect the way in which your short messages are sent and received. 1 Press the Menu key in the main view of Messaging and select Tools > Account settings…. 2 Select Short message and press Edit. A dialog with two pages opens. Define the following: General page Press Service centres, which opens a dialog where you can define new message centres, as well as edit and delete existing ones.
Linda1.book Page 187 Friday, April 12, 2002 8:31 PM Advanced page Reply via same centre: This network service allows the recipient of your short message to reply using your message centre. If you chooseYes and the recipient replies to your message, the return message is sent using the same service centre number. This requires that the recipient has subscribed to the Short Message Service, is able to a reply to a message, and uses a device which supports this feature.
Linda1.
Linda1.book Page 189 Friday, April 12, 2002 8:31 PM 10. Office Office contains the Word Processor, Sheet, and Presentation viewer applications, which are all compatible with Microsoft Windows. Office also contains a File manager application for file and folder management tasks like moving, copying, and renaming files and folders. Figure 75 Word Processor You can use Word Processor to write new and edit existing text documents. You can insert and view images and other files in the documents.
Linda1.book Page 190 Friday, April 12, 2002 8:31 PM Office 190 To create a new document Tip: You can use the clipboard command shortcuts Ctrl+x, Ctrl+c, and Ctrl+v to cut, copy, and paste text. When you open the Word Processor application, a new document is opened. You can start writing immediately. You can modify the style of a document on a font and a paragraph level. You can use different fonts, font sizes, and styles.
Linda1.
Linda1.book Page 192 Friday, April 12, 2002 8:31 PM Office 192 Templates Example: You may have a company template which shows the company name and defines a particular layout. You can use templates and save documents as templates when creating and editing documents. To select a template, press the Menu key and select File > Templates > Select template…. A list of available templates opens. Select a template and press OK.
Linda1.book Page 193 Friday, April 12, 2002 8:31 PM 193 Office Note: Objects in a document are not links but embedded attachments, which may increase the file size of the document dramatically. To hide or make visible text markers To hide or make visible markers that are used in editing within the document, proceed as follows. 1 Press the Menu key and first select Tools > Preferences…. A dialog with two pages opens.
Linda1.book Page 194 Friday, April 12, 2002 8:31 PM 194 Office Sheet In Sheet you can work and store your data in a file that is called a workbook. Each workbook contains at least one worksheet. A workbook can also contain chartsheets; a chartsheet is a spreadsheet file containing a chart that is based on data from a worksheet. You can open, edit and save documents created with Microsoft Excel for Windows versions 95, 97 and 2000.
Linda1.book Page 195 Friday, April 12, 2002 8:31 PM To enter data To enter data, select a cell with the Arrows key and start typing the data in the selected cell. To confirm what you have entered into a cell, press Enter, OK, or go to another cell with the Arrows key. To dismiss the action, press Esc or Cancel. You can also enter a formula to perform operations on worksheet data. Sheet application provides some predefined, or built-in, formulas, which are known as functions.
Linda1.book Page 196 Friday, April 12, 2002 8:31 PM Office 196 Example: You might want to sum up figures in cells C2 to C4 in cell C5; select cell C5, press Point reference and select the cell range from C2 to C4. Press Enter or OK to confirm the action. The SUM will now appear in C5. In a formula, you can enter constant values or cell references. A cell reference tells Sheet where to look for the values or data you want to use in the formula.
Linda1.book Page 197 Friday, April 12, 2002 8:31 PM The selection is cleared when you press the Arrows key or Tab key. To insert cells 1 Select a number of cell(s) that you want to insert into the worksheet. 2 Press the Menu key and select Insert > Cells. A dialog opens. 3 Define whether you want the inserted cell or cells to appear above (Shift cells down) or left (Shift cells right) of the selected range. To insert an entire row(s) or column(s), select either Entire row or Entire column.
Linda1.book Page 198 Friday, April 12, 2002 8:31 PM Office 198 Tip: Pressing Options opens up the following options: Search in values, Search in formulae, Match case, Find entire cells only, Direction, and Search by. 3 Press Find to search for the string. Press Options to search the worksheet according to certain criteria. Press Replace to replace the string with something else. To clear cells 1 Choose the cell or cells you want to clear. 2 Press Clear. A lists of choices appears.
Linda1.book Page 199 Friday, April 12, 2002 8:31 PM To align cell contents 1 Select the cell or cells. 2 Press the Menu key and select Format > Alignment. A dialog opens. 3 Define the following options: Horizontal, Vertical, and Wrap text to cell. To change the appearance of cell borders 1 Select the cell or cells. 2 Press the Menu key and select Format > Cell appearance > Borders. A dialog opens. 3 Define the following options: Outline, Top, Bottom, Left, Right, and Line colour.
Linda1.book Page 200 Friday, April 12, 2002 8:31 PM 200 Office 2 Press the Menu key and select Format > Cell appearance > Background colour. A dialog opens. 3 Choose the colour. To insert page breaks 1 Press the Menu key and select Insert > Page break. A dialog opens. 2 Define the following options: Break at column and Break at row. Note: Since the break is placed above and on the left side of the selected cell, you cannot insert a page break when the cell A1 is selected.
Linda1.book Page 201 Friday, April 12, 2002 8:31 PM To go to any sheet or chart within the same workbook 1 Press the Menu key and select View > Worksheets or Sheets/Charts. A list opens. 2 Choose a sheet or chart and press OK to open the sheet and Cancel to dismiss it. Note: You cannot change the order of the sheets. Tip: To view sheets in the Chartsheet view, press Sheets/ Charts.
Linda1.book Page 202 Friday, April 12, 2002 8:31 PM 202 Office To delete the object, press Delete. 4 Define the new values. Figure 81 5 Press Close to confirm the changes or Esc to dismiss them. Note: You can select only one object at a time. To replace chartsheet data Tip: To define the general appearance of a chart, press Chart settings. Define the page style and name in the two pages of the dialog which opens. You can replace the data on which your chartsheet is based.
Linda1.book Page 203 Friday, April 12, 2002 8:31 PM 203 Office You can view documents created with Microsoft PowerPoint for Windows versions 95,97 and 2000. Note that not all features and formatting of the original documents will be supported. To view a presentation Press Open in the Presentation main view to select and view a document. To close the application, press Close. When a document is opened, the top of the first slide is shown. To view the next slide, press Next or Enter.
Linda1.book Page 204 Friday, April 12, 2002 8:31 PM 204 Office To search for and view a slide 1 Press the Menu key and select Tools > Go to slide…. A list of the slides in the presentation opens. 2 Go to the slide you want by using the Arrows key. 3 Press Go to open the slide. To view the presenter’s notes To view the presenter’s notes along with the slides, press the Menu key and select View > Notes view.
Linda1.book Page 205 Friday, April 12, 2002 8:31 PM 205 Office The folder view The folder tree can contain folders from two roots, the communicator and a memory card. Under the communicator root there is C:\Documents\ folder that contains four default folders: \Documents\Downloaded\, \Documents\Photo gallery\, \Documents\Templates\, and \Documents\Tones\. To show or hide subfolders in the folder list frame, press < and > on the Arrows key.
Linda1.book Page 206 Friday, April 12, 2002 8:31 PM Office 206 A view of all the subfolders and files of the parent folder opens. See Figure 84. Figure 84 2 To view any possible subfolder, select it and press Open. 3 To view parent folders, press Esc. 4 Press Close folder to return to the main view. The title of the folder content view shows the path name and the number of files and subfolders in the folder, together with the total size of all the files in the folder.
Linda1.book Page 207 Friday, April 12, 2002 8:31 PM To move files and folders 1 Select folders or files that you want to move and press Move in the main view of File manager. A list of folders opens, as shown in Figure 85. Figure 85 2 Search for a target folder with the Arrows key. To hide or show the subfolders of a folder, press Collapse and Expand respectively. You can also navigate in the folder list with the Arrows key and +/ - keys. To create a new target folder, press New folder.
Linda1.book Page 208 Friday, April 12, 2002 8:31 PM 208 Office To rename files and folders 1 Select the file or folder in the main view of File manager. 2 Press the Menu key and select File > Rename. The cursor now appears at the beginning of the selected file or folder name. 3 Rename the file or folder. 4 To confirm the changes, press OK. To dismiss the changes, press Cancel.
Linda1.book Page 209 Friday, April 12, 2002 8:31 PM Figure 87 Press Change to change the value of a list item. When ready, press Close. 5 Press Find to start the search. To interrupt the search, press Stop. 6 When the search is over, press Open to open the folder or file found. To start a new search, press New find. 7 To return to the main view, press Close. To back up and restore data to and from a memory card It is advisable to take backups of your communicator data regularly.
Linda1.book Page 210 Friday, April 12, 2002 8:31 PM Office 210 folders. For information about selective backups, selective restoring, and using a PC to back up and restore, see the PC Suite guide on the sales package CD-ROM. To be able to back up to and restore from a memory card, the card should be inserted in the communicator. For details, see ‘To insert a memory card’ on page 25.
Linda1.book Page 211 Friday, April 12, 2002 8:31 PM Note: Use a password that is easy for you to remember but difficult for others to guess. If you forget your password, the only way to use your memory card again is to format the card. Formatting deletes all data from the card! To format a memory card press the Menu key, select Memory card > Format memory card…, and press Format. Office 211 To remove password protection, press the Menu key and select Memory card > Security > Remove password….
Linda1.
Linda1.book Page 213 Friday, April 12, 2002 8:31 PM 213 Extras 11. Extras Extras contains the following applications: Calculator, Clock, Control panel, Recorder, Imaging, Cell broadcast, Video player, and Fax modem. Most of the new applications that you install will be added to the Extras application group. For more information on applications available on the sales package CD-ROM, see Software on CD-ROM Guide in the Using Nokia 9210i Communicator section of the CD-ROM.
Linda1.book Page 214 Friday, April 12, 2002 8:31 PM Extras 214 Tip: To choose the clock type, press the Menu key and select View > Clock type > Digital or Analogue. Tip: To turn off a sounding alarm, press Stop or any key on the keypad of the phone cover. Press Snooze to silence the alarm for five minutes. Tip: The world map shows the currently selected city in cross hairs. To set an alarm 1 2 3 4 Press Alarm clock in the main view. An alarm clock view opens.
Linda1.book Page 215 Friday, April 12, 2002 8:31 PM Calculator There are two modes in Calculator: desk calculator for simple arithmetic operations and scientific calculator for more complicated mathematical calculations. There are two ways to perform calculations, either by typing the characters in the input field or selecting symbols from the function map. A calculation is executed by pressing Enter or =. The calculation and its result can be seen on the output sheet on the left.
Linda1.book Page 216 Friday, April 12, 2002 8:31 PM Extras 216 Note: For more detailed information about Calculator, see the Nokia 9210i Communicator help.
Linda1.book Page 217 Friday, April 12, 2002 8:31 PM The codes are shown as asterisks. If you are changing a code, you will be prompted for the current code and then the new code twice. PIN code request: If you set the PIN code request On, the communicator requests that you enter the code every time you turn on the phone. If you enter the PIN code incorrectly three times in succession, you will need a PUK code to unblock the SIM card.
Linda1.book Page 218 Friday, April 12, 2002 8:31 PM Extras 218 Tip: Changing the PIN code requires that PIN code request is selected, the phone is on, and that there is a valid SIM card inserted. Tip: Changing the barring password requires that the phone is on and the Call barring service is activated for your SIM card. Lock if SIM card is changed: If set On, every time the phone is switched on this security option checks whether the SIM card in the communicator has been changed.
Linda1.book Page 219 Friday, April 12, 2002 8:31 PM 219 Extras Note: When the communicator is locked, calls may be possible to the emergency number programmed into your phone (e.g. 112 or other official emergency number). Data call barring Here you can prevent or allow the following data call types: Note: You need a barring password to modify these settings. Outgoing calls: When activated, prohibits making data calls. Incoming calls: When activated, prohibits receiving data calls.
Linda1.book Page 220 Friday, April 12, 2002 8:31 PM Extras 220 2 Select the accessory options that you want to modify. The options are Headset/ Car kit. Press Edit. 3 Define the following: Car kit settings Automatic answer: Allows you to define whether the automatic answering is on or off when your communicator is attached to the car kit. Default profile: Allows you to choose the profile that will be automatically selected, when you attach your communicator to the car kit.
Linda1.book Page 221 Friday, April 12, 2002 8:31 PM 221 Extras Contrast and brightness page Figure 92 Press + and - to adjust the bar you are editing. Contrast level: Pressing + increases and - decreases the contrast of the display. Brightness: The brightness level of the display. There are five levels to choose from. Brightness period: A time period after which, if there has not been any key presses within that time, the brightness will go down to its lowest level.
Linda1.book Page 222 Friday, April 12, 2002 8:31 PM Extras 222 Certificate manager With Certificate manager you can manage digital certificates which you use when connecting to WWW sites, WAP services, mail servers, and when installing software.
Linda1.book Page 223 Friday, April 12, 2002 8:31 PM To check that a certificate is authentic Certificates are used to verify the origin of WWW pages and installed software. However, they can only be trusted if the origin of the certificate is known to be authentic. If you are adding a new certificate, or want to check the authenticity of an existing certificate, proceed as follows: 1 Select the certificate and press View details. A view of certificate details opens.
Linda1.book Page 224 Friday, April 12, 2002 8:31 PM Extras 224 To delete a certificate, select it and press Delete. Date and time Here you define the current time and date for your communicator. Time: The current time. Date: The current date. Daylight-saving: Determines how the time of your communicator is affected by changes in daylight saving time. The options are On/Off/Define summer. If Define summer is selected, you have to enter the dates Summer starts and Summer ends.
Linda1.book Page 225 Friday, April 12, 2002 8:31 PM 225 Extras Note: If you install software that is not intended specifically for the Nokia 9210/9210i Communicator, its usage can differ significantly from the usual Nokia 9210/9210i Communicator applications. You can download or transfer a software package containing the files of the application into the communicator. Then you can install the application. Software can also be installed from a memory card.
Linda1.book Page 226 Friday, April 12, 2002 8:31 PM Extras 226 Tip: If you have installed PC Suite for Nokia 9210i Communicator on your PC and the communicator is connected to your PC, you can also install software by double-clicking a file ending with .sis stored on your PC. Figure 93 If you see this warning message, only continue installation if you are absolutely sure of the origin and contents of the software package.
Linda1.book Page 227 Friday, April 12, 2002 8:31 PM Installation log To view the list of software installations and removals that have taken place, press the Menu key and go to the Install log page. This list shows what software has been installed and removed, and when that happened. If you encounter problems with the device after installing a software package, you can use this list to find out which software package may be the cause of the problem.
Linda1.book Page 228 Friday, April 12, 2002 8:31 PM Extras 228 Default installation language - You can set the default installation language to the language that your Nokia 9210i Communicator has. If the software package contains several different language versions of the software, the language version specified here will be installed. Sort installed software by - To sort the list of installed software packages, select one of the options Name, Type, or Size.
Linda1.book Page 229 Friday, April 12, 2002 8:31 PM 229 Extras If a memory card is inserted in the communicator, press Memory card to view the amount of available memory on the card. Press Device to return to view the communicator memory. If the memory is getting low, you should remove some documents. Before removing, you can print, fax, or mail them, or transfer them to a PC or a memory card. Regional settings On these four pages you can define the local time, date, numbering, and currency expressions.
Linda1.book Page 230 Friday, April 12, 2002 8:31 PM Extras 230 You can open files that have been stored in the following file formats: .WAV, .AU, and compressed GSM encoded file format. Compression is done implicitly during the recording process. Recorder contains all the controls like Play, Stop, Pause, and Record that are typically found in recording equipment. Press Resume to continue after recording or playback has been paused.
Linda1.book Page 231 Friday, April 12, 2002 8:31 PM 231 Extras Imaging The Imaging application acts as a file manager for images. Application folders created for storing images are called albums. Images appear as thumbnail images in albums. A thumbnail image is a small image representing the original full size image. Imaging supports a wide range of image formats, among them JPEG, TIFF, GIF, BMP, MBM, and WBMP. You can open all commonly used image files directly for viewing.
Linda1.book Page 232 Friday, April 12, 2002 8:31 PM 232 Extras You can also receive images via IR. For details, see ‘To receive images via infrared’ on page 234. To create a new album 1 Press the Menu key and select File > New album…. A dialog opens. 2 Define the following: Name: Name of the album. 3 To save the album in the communicator, press Create locally. To save the album in a memory card, press Create in mem. card.
Linda1.book Page 233 Friday, April 12, 2002 8:31 PM Press the Menu key and first select Edit > Copy or Cut. Open the target album. Press the Menu key and select Edit > Paste. If the target album already has an image or images with the same name, a confirmation note appears asking you if you wish to replace the existing image. Choose from the following options: Replace - The existing image is replaced with the image you are pasting. Replace all - All existing images are replaced with the same name.
Linda1.book Page 234 Friday, April 12, 2002 8:31 PM 234 Extras 2 Scroll with the Arrows key to select the new size and press Select or press Best fit to fit the image horizontally to the screen. To receive images via infrared Tip: Large images transferred from a digital camera may take too much internal memory to be viewed. To scale the size of the transferred images down to 640x480 pixels, press the Menu key and select Tools> Use VGA, if the option is not already selected.
Linda1.book Page 235 Friday, April 12, 2002 8:31 PM Extras 235 Figure 96 To start or stop receiving CBS messages, in the main view of Cell broadcast, press Reception on or Reception off. Press Read to read messages and press Next or use the commands in the View menu to browse for more messages. To subscribe, scroll to a topic and press Subscribe. A check mark is displayed in the box on the left-hand end of the topic. To unsubscribe, press Unsubscribe. Tip: You can search for different topics.
Linda1.book Page 236 Friday, April 12, 2002 8:31 PM Extras 236 Tip: You can sort the topics by pressing the Menu key and selecting a sorting command in the View menu. To change the name of the list that is open, press the Menu key and select List > Rename list… Note that the reception must be turned off. To open topic lists To open a different list, press the Menu key and select List > Select topic list. In different topic lists, you can still subscribe and unsubscribe topics and set them as hot topics.
Linda1.book Page 237 Friday, April 12, 2002 8:31 PM Fax modem You can use the communicator as a fax modem with a compatible PC. Your communicator can be connected to a PC via serial cable or by using an infrared connection. Before your PC can recognise the communicator as a fax modem, you need to install a new modem configuration for your PC. Please refer to your operating system manual for more information. During the installation you may be asked to enter the path to the modem information file.
Linda1.book Page 238 Friday, April 12, 2002 8:31 PM Extras 238 Tip: To use High Speed connection, your GSM operator must activate High Speed Data Services on your SIM card. 5 In the field What type of modem do you want to install? select Other. Click Next 6 Select the option Don’t detect my modem; I will select it from a list 7 Click Have disk... 8 Click Browse and locate the CD-ROM drive with the Nokia 9210i CD-ROM.
Linda1.book Page 239 Friday, April 12, 2002 8:31 PM Fax modem settings To open Fax modem, press the Extras application button, select Fax modem, and press Open Note that an active PC connection using the fax modem is disconnected after 20 minutes if no data is sent or received. However, an active call is not automatically disconnected. Note: You cannot change fax modem settings if the fax modem is activated. To change these settings, make sure that fax modem is not active.
Linda1.book Page 240 Friday, April 12, 2002 8:31 PM Extras 240 Parity: A parity error-checking procedure. The default option, None, can typically be used. Stop bits: Defines number of stop bits used. The default option, 1, can typically be used. Flow control: It is recommended to select Software. This setting needs to be the same in you PC as well. Operating system page Windows 2000: If you are not using Windows 2000, select No and press Done. The rest of the options on the page are dimmed.
Linda1.book Page 241 Friday, April 12, 2002 8:31 PM 12. Troubleshooting If you have problems with your communicator, Club Nokia Careline answers questions and offers instructions over the phone. For more information on the Club Nokia Careline see the Accessories section of the Getting Started Guide and Nokia Careline Web page. You can also visit Forum Nokia at www.forum.nokia.com for information and support material related to the communicator. 1.
Linda1.book Page 242 Friday, April 12, 2002 8:31 PM Troubleshooting 242 Check that the flight mode is not active. For more information see ‘Flight profile’ on page 91. Restart the communicator by removing the battery, waiting thirty seconds, and replacing it again. Try charging the communicator. If you see the battery level indicator on the phone but the phone does not work, contact your local Nokia dealer. Check the signal strength indicator: you might be outside the network service area.
Linda1.book Page 243 Friday, April 12, 2002 8:31 PM 243 Troubleshooting 4 Temporary files are deleted. This empties the cache, removes cookies, resets plug-in registrations and resets the settings you have made in some of the applications including all Internet and profile settings, Desk shortcuts and display settings. All other applications and files stay intact.
Linda1.book Page 244 Friday, April 12, 2002 8:31 PM Troubleshooting 244 5. Cannot make or receive calls Check to see if you have ‘Flight’ profile turned on. When this profile is active you cannot make or receive calls. Make sure that the phone is not off. Close the cover and switch on the phone. If you get the message INVALID SIM CARD, your SIM card cannot be used in the communicator. Contact you dealer or network service provider.
Linda1.book Page 245 Friday, April 12, 2002 8:31 PM 8. Cannot select a contact If you cannot select a contact in the Telephone, Fax, SMS or Mail directory, the contact card does not have a telephone number, fax number, wireless phone number or an e-mail address. Add the missing information to the contact card in the Contacts application. 9. Cannot send or receive faxes, short messages or mail Make sure that you have subscribed to these network services.
Linda1.book Page 246 Friday, April 12, 2002 8:31 PM Troubleshooting 246 remote mailbox service, or the Internet servers between the communicator and the remote mailbox. Try again after a couple of minutes, and then contact your Internet Service Provider. Mail sending: You have not subscribed to a remote mailbox service, or the mail server delivering your mail does not comply with the SMTP protocol. If you are using secure connections, your remote mailbox service also has to support secure connections.
Linda1.book Page 247 Friday, April 12, 2002 8:31 PM The received message is over 1377 characters long. Use the Messaging application to read it. 11.
Linda1.book Page 248 Friday, April 12, 2002 8:31 PM Troubleshooting 248 3 If the data call is active, but you cannot download WWW pages with the WWW browser, make note of the most recent status indication displayed to you in the title bar of the WWW browser.
Linda1.book Page 249 Friday, April 12, 2002 8:31 PM The PC to which you want to establish the connection must have an IrDA compatible infrared port; installed and activated IrDA drivers; and Microsoft Windows 95/98/98SE/Me. For more information on IrDA drivers and their use in Windows, contact Microsoft. If you have an IBM Thinkpad laptop with Windows 98 SE installed, you may encounter problems with infrared connections.
Linda1.book Page 250 Friday, April 12, 2002 8:31 PM Troubleshooting 250 13. Printing problems If you are using the infrared connection, the infrared port of the printer must be compatible to the IrDA standard. See ‘To print’ on page 31. If you fail to establish an infrared connection, transfer the file to a PC and use the PC to print the document. Alternatively, you can fax the document to the nearest fax machine. See ‘To write and send a new fax’ on page 166. 14.
Linda1.book Page 251 Friday, April 12, 2002 8:31 PM If you have problems establishing a data connection with the remote modem, try fixing the data transmission rate by using an AT command. Common AT commands based on the ETSI 07.07 standard and supported by the Nokia 9210i Communicator are listed in a file on the CD-ROM supplied with the communicator. You can find this file by clicking ‘AT commands’ in ‘PC software section’ on the CD-ROM.
Linda1.book Page 252 Friday, April 12, 2002 8:31 PM Troubleshooting 252 • You have received a lot of mail or you have saved large images or other items that use a lot of memory. To free up communicator memory, remove unnecessary data, move large items to a memory card or transfer them to your PC, if possible. See ‘To avoid low memory’ on page 164 and PC Suite Guide for details. • You have tried to download a large WWW page. See item 19 on this troubleshooting list.
Linda1.book Page 253 Friday, April 12, 2002 8:31 PM Troubleshooting 253 Note: Removing data files or installing applications does not have effect on the memory available to the WWW browser.
Linda1.
Linda1.book Page 255 Friday, April 12, 2002 8:31 PM 13. CARE AND MAINTENANCE Your Nokia 9210i Communicator is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. • Keep the communicator and all its parts and accessories out of the reach of small children. • Keep the communicator dry.
Linda1.book Page 256 Friday, April 12, 2002 8:31 PM CARE AND MAINTENANCE 256 • Do not drop, knock or shake the communicator. Rough handling can break internal circuit boards. Dropping the product may break the colour display, which is fragile. • Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the communicator. • Do not paint the communicator. Paint can clog the moving parts and prevent proper operation. • Use only the supplied or an approved replacement antenna.
Linda1.book Page 257 Friday, April 12, 2002 8:31 PM 14. IMPORTANT SAFETY INFORMATION Traffic Safety Do not use a communicator while driving a vehicle. Always secure the phone in its holder; do not place the phone on the passenger seat or where it can break loose in a collision or sudden stop.
Linda1.book Page 258 Friday, April 12, 2002 8:31 PM IMPORTANT SAFETY INFORMATION 258 Electronic devices Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain electronic equipment may not be shielded against the RF signals from your communicator. Pacemakers. Pacemaker manufacturers recommend that a minimum separation of 20 cm (6 inches) be maintained between a hand-held wireless phone and a pacemaker to avoid potential interference with the pacemaker.
Linda1.book Page 259 Friday, April 12, 2002 8:31 PM Vehicles. RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (e.g. electronic fuel injection systems, electronic anti-skid (anti-lock) braking systems, electronic speed control systems, air bag systems). Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. Posted facilities.
Linda1.book Page 260 Friday, April 12, 2002 8:31 PM IMPORTANT SAFETY INFORMATION 260 Vehicles Only qualified personnel should service the communicator, or install the communicator in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty which may apply to the unit. Check regularly that all wireless phone equipment in your vehicle is mounted and operating properly.
Linda1.book Page 261 Friday, April 12, 2002 8:31 PM Emergency calls Emergency calls may not be possible on all wireless phone networks or when certain network services and/or phone features are in use. Check with local service providers. To make an emergency call: . 1 If the device cover is open, close it. 2 If the phone is not on, switch it on. Check for adequate signal strength. Some networks may require that a valid SIM card is properly inserted in the communicator. 3 Press as many times as needed (e.
Linda1.book Page 262 Friday, April 12, 2002 8:31 PM IMPORTANT SAFETY INFORMATION 262 Important power supply information WARNING: This apparatus is intended for use when supplied with power from a Lithium-ion battery and chargers ACP-12, ACP-9E, ACP-9X and ACP-9A. Other usage will invalidate any approval given to this apparatus and may be dangerous. Use only batteries, chargers and accessories approved by the communicator manufacturer for use with this particular communicator model.
Linda1.book Page 263 Friday, April 12, 2002 8:31 PM The exposure standard for mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit stated in the international guidelines is 2.0 W/kg*. Tests for SAR are conducted using standard operating positions with the phone transmitting at its highest certified power level in all tested frequency bands.
Linda1.
Linda1.book Page 265 Friday, April 12, 2002 8:31 PM 265 Glossary AT Commands Operations of a fax modem can be controlled by AT commands. These commands give the advanced user an opportunity to control all the features of the modem. A list of common AT commands based on the ETSI 07.07 standard and supported by the Nokia 9210i Communicator is available on the CD-ROM included in the sales package of your communicator.
Linda1.book Page 266 Friday, April 12, 2002 8:31 PM 266 Domain name and Host name The terms “domain name” and “host name” are sometimes, slightly inaccurately, used as synonyms. In a full domain name, e.g. www.forum.nokia.com, the first part of the name is the name of the host, and the following parts are names of domains to which the host belongs. Each host name corresponds to a certain IP address. Host names are used because they are easier to remember than IP addresses.
Linda1.book Page 267 Friday, April 12, 2002 8:31 PM 267 HTML (Hypertext Mark-up Language) A language used to define the appearance and content of WWW documents. HTTP (Hypertext Transfer Protocol) A document transfer protocol used in the WWW. HTTPS HTTP over a secure connection. See Secure Socket Layer (SSL) Hyperlink A link on a WWW page that leads to another World Wide Web page or site, or another place on the same page.
Linda1.book Page 268 Friday, April 12, 2002 8:31 PM 268 IETF (Internet Engineering Task Force) IETF are responsible for most of the Internet standardisation. Nokia 9210i Communicator is using many IETF specifications. In the callback settings, one of the settings is specified by IETF whereas the other methods are specified by Microsoft. ISDN connections ISDN connections are a way to establish a data call between the Communicator and your Internet Access Point.
Linda1.book Page 269 Friday, April 12, 2002 8:31 PM 269 MCN (Micro-Cellular Network) technology Microcells are used for increasing the capacity of wireless networks in urban areas. MIME (Multipurpose Internet Mail Extensions) A standard Internet format which permits, for instance, multiple mail objects in a single message. The mail objects can be, for example, formatted multifont text messages and non-textual elements, such as images and audio fragments.
Linda1.book Page 270 Friday, April 12, 2002 8:31 PM 270 Point-to-point protocol (PPP) A common networking software protocol which enables any computer with a modem and a phone line to connect directly to the Internet. Protocol A formal set of rules that govern how data is transferred between two devices. Proxy In some networks, the connection between the WWW and the site you want to connect to is blocked by a firewall. The firewall protects the network from unauthorised external access.
Linda1.book Page 271 Friday, April 12, 2002 8:31 PM 271 which require the PIN2 code. To use these functions again, you will need to obtain a new SIM card from your network service provider.You cannot change the PUK2 code. Roaming agreement An agreement between two or more network service providers to enable the users of one service provider to use the services of other service providers.
Linda1.book Page 272 Friday, April 12, 2002 8:31 PM 272 Template In word processing a template or a style sheet is a file or form that defines the layout of a document. A template may determine parameters like the page size, margins, and fonts. You can use the same style sheet for many documents. For example, you can define one style sheet for personal letters, another for official letters, and a third for reports.
Linda1.book Page 273 Friday, April 12, 2002 8:31 PM 273 WAP access point An extension to an Internet access point (see: IAP), which provides additional information that the WAP browser needs in order to be able to connect to a WAP service.
Linda1.
