User Guide

ManualsBrandsNokia ManualsCell Phone9300

Issue 1 12/04 COMPANY CONFIDENTIAL

Nokia Customer Care

3 - Service Software

Instructions

Summary of content (106 pages)

PAGE 3
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Table of Contents Page No Quick Guide for Phoenix Service SW Installation............................................ 5 Service requirements ......................................................................................... 5 Supported operating systems .......................................................................... 5 Hardware requirements ...................................................................................
PAGE 4
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Table of Contents Page No Receiver Manual Tuning ................................................................................... 49 Rx Channel Select Filter Calibration ................................................................ 49 Rx Calibration .................................................................................................. 50 RX Band Filter Response Compensation ..................................................
PAGE 5
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Quick Guide for Phoenix Service SW Installation ■ Service requirements Supported operating systems • Windows 2000 (service pack 2) • Windows XP (service pack 1) Hardware requirements Recommended for Windows 2000 • Processor 700 MHz, RAM memory 256 MB, disk space 150 MB. Service software The service software used is called Phoenix.
PAGE 6
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Phoenix installation steps in brief DCT-4 generation test and service software is called “Phoenix”. These are the basic steps to install Phoenix: • Connect a DK2 dongle or FLS-4S POS flash device. • Install the Phoenix service SW. • Install the data package for Phoenix. • Configure users. • Manage connection settings (depends on the tools you are using). • Phoenix is now ready for FLS-4S Point Of Sales flash device use.
PAGE 7
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Phoenix Service SW ■ Before installation • Check that a dongle is attached to the parallel port of your computer. • Download the installation package (e.g. phoenix_service_sw_a15_2004_41_5_28.exe) to your computer (e.g. C:\TEMP). • Close all other programs. • Run the application file (e.g. phoenix_service_sw_a15_2004_41_5_28.exe) and follow instructions on the screen.
PAGE 8
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Installing Phoenix 1. To start installation, run the phoenix_service_sw_a15_2004_41_5_28.exe. Install Shield starts. 2. To continue, click "Next" in the Welcome dialog. 8 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 9
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 3. Read the text carefully: 4. Choose destination folder. It is recommended to use the default folder C:\ProgramFiles\Nokia\Phoenix. 5. To continue, click “Next”. You may choose another location by clicking “Browse” (not recommended). Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 10
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Setup copies the components, progress of the setup is shown. Please wait… Drivers are installed and updated, please wait. The process may take several minutes to complete. 10 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 11
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care If the operating system does not require rebooting (Windows 2000, XP), the PC components are registered straight away. 6. Click "Finish". Phoenix is ready for use. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 12
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 7. If the operating system used requires restarting your computer, the Install Shield Wizard notifies you about it. Select "Yes..." to reboot the PC immediately and "No..." to reboot the PC manually afterwards. After the reboot, components are registered and Phoenix is ready for use. Note that Phoenix does not work, if components are not registered.
PAGE 13
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care ■ Updating Phoenix installation If you already have the Phoenix service SW installed on your computer, you will need to update it when new versions are released. Always use the latest available versions of both the Phoenix service SW and the phone specific data package. Instructions can be found in phone model specific Technical Bulletins and phone data package readme.txt files (shown during installation).
PAGE 14
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Uninstalling Phoenix Uninstallation can be done manually from the Windows’s control panel. 1. Choose Add / Remove Programs -> “Phoenix Service Software”. 2. To uninstall Phoenix, click "Add/Remove" -> “Remove”. Progress of the uninstallation is shown. 14 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 15
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 3. If the operating system does not require rebooting, click “Finish” to complete. 4. If the operating system requires rebooting, Install Shield Wizard notifies you about it. Select "Yes..." to reboot the PC immediately and "No..." to reboot the PC manually afterwards. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 16
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Repairing Phoenix installation If you experience any problems with service software or suspect that files have been lost, you can use the repair function before completely reinstalling Phoenix. Note that the original installation package (e.g. phoenix_service_sw_a15_2004_41_5_28.exe) must be found on your PC when you run the repair setup. To repair: 1. Run Windows Control Panel. 2.
PAGE 17
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Data Package for Phoenix (Product Specific) ■ Phoenix data package overview Each product has its own data package (DP).
PAGE 18
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Installing Phoenix data package (product specific) 1. To start installation, run the application file (e.g. RAE6_dp_v_1.0_MCUSW4_51.exe). 2. To extract files needed for installation, click “Next”. Please wait… 3. To continue, click “Next”. 18 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 19
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 4. From this view, you can see the contents of the data package. Read the text carefully. There should be information about the Phoenix version needed with this data package. Click “Next”. 5. To continue, confirm location and click “Next”. Install shield checks where the Phoenix application is installed and the directory is shown. 6. To continue, click “Next”. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 20
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 7. To start copying the files, click “Next”. Phone model specific files are installed. please wait. 20 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 21
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 8. To complete installation, click “Finish”. You now have all phone model specific files installed in your Phoenix service SW. Now Phoenix can be used to for example flash phones and print type labels after: • Configuring users • Managing connections • FLS-4S can be used right away • FPS-8* can be used after updating flash update package files to it Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 22
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Uninstalling data package 1. To uninstall the data package manually from Windows, choose Control Panel / Add / Remove Programs/ -> RAE-6/RA-4 Phone Data Package. 2. If you try to install the same version of Phoenix data package that you already have, you are asked if you want to uninstall the current version. Answer “OK” to uninstall, “Cancel” if you do not want to uninstall.
PAGE 23
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Configuring Users To configure users: 1. Start Phoenix service SW and login. 2. To add new user or edit an existing one, click “Maintain”. If a user ID is already configured, choose your own user ID from the list and click “OK”. 3. To add information for the new user, click “New”. 4. Type in your name and Initials to fields and click “OK”. 5. User has now been created, click “OK”.
PAGE 24
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Managing Connections Manage connections feature in Phoenix is for selecting, editing, and deleting existing connections, and creating new ones. To manage connections: 1. Start Phoenix service SW and login. 2. From the “File” menu, choose “Manage Connections”. 3. In this dialog, you can select, edit, delete existing connections and create new ones. You can create a connection either manually or by using a Connection Wizard.
PAGE 25
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 4. To continue, click “Next”. 5.
PAGE 26
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 9. Click “Apply”. The connection is now selected and can be used after closing the “Manage Connections” window. The selected connection is shown at the right-hand bottom corner of the screen. 10.To use the selected connection, connect the phone to Phoenix with correct service tools, make sure that it is switched on and choose “Scan Product”.
PAGE 27
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Updating Flash Support Files for FPS-8* and FLS-4* ■ Before installation • Install Phoenix service SW. • Install phone model specific data package for Phoenix. • The flash support files are delivered in the same installation package with Phoenix data packages or newer Phoenix packages beginning from September 2003.
PAGE 28
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions that. If you try to downgrade the existing version, the setup will be aborted. However, if you want to downgrade, uninstall newer files manually from the Control Panel and then rerun the installation again. If an older version exists on your PC and it needs to be updated, click “Next” to continue installation. It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia\Phoenix. 2.
PAGE 29
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care other location by clicking “Browse” (not recommended). The installation continues… 3. To complete the procedure, click “Finish”. FLS-4 can be used right after the flash update package is installed. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 30
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions FPS-8* flash prommer must be updated by using Phoenix! ■ Updating FPS-8* flash prommer SW There are two ways to update the FPS-8 flash prommer software: Option 1: 1. Start Phoenix service software and login. 2. Manage connection correctly for the FPS-8* flash prommer. 3. From the ”Flashing” menu, choose ”FPS-8 Maintenance” 30 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 31
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 4. When a new FPS-8 flash update package is installed to your computer, you are asked to update the files to your FPS-8 Prommer. To update files, click ”Yes”. The update procedure takes a couple of minutes, please wait until you are notified that the update has been successful. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 32
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 5. Click “OK” and close the “FPS-8 Maintenance” window. View after successful prommer software update. Option 2: 1. Click the ”Update” button. 32 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 33
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 2. Select the appropriate fps8upd.ini file under the C:\Program Files\Nokia\Phoenix\Flash directory 3. All files can be loaded separately to FPS-8. To do this, press the right mouse button in the ”Flash box files” window and select the desired file type. More information and help can be found from the “Help” dialog. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 34
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Activating and Deactivating FPS-8 Before the FPS-8 can be successfully used for phone programming, it must be first activated. If there is a need to send the FPS-8 box to somewhere, e.g. for repair, the box must be first deactivated. ■ Activating FPS-8 1. Fill in the “FPS-8 activation request” sheet included in the FPS-8 sales package and follow the instructions given in the sheet. 2. When the activation file is received (e.g. 00000.
PAGE 35
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 5. In the “FPS-8 Maintenance” window, click “Activate.”. The activation file you saved to C:\ProgramFiles\Nokia\Phoenix\BoxActivation is displayed (e.g. 00000.in), check that it is correct. 6. To activate the box, click “Open”. 7. To complete the activation, turn FPS-8 power off and on. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 36
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Deactivating FPS-8 1. Start Phoenix service software. 2. From the ”Flashing” menu, choose ”FPS-8 Maintenance”. 3. In the “FPS-8 Maintenance” window, click “Deactivate”. 4. To confirm deactivation, click “Yes”. The box is deactivated. 5. To complete deactivation, turn FPS-8 power off and on. 36 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 37
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care JBV-1 Docking Station SW The JBV-1 docking station is a common tool for all DCT-4 generation products. In order to make the JBV-1 usable with different phone models, a phone specific docking station adapter is used for different service functions. The JBV-1 docking station contains software (firmware) which can be updated.
PAGE 38
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 2. To continue, click “Next”. 3. Use the destination folder suggested which JBV-1 SW package is installed to and click “Next” to continue. 38 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 39
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 4. To continue, select “Full” and click “Next”. The program folder is created. 5. To continue, click “Next”. Software files are installed. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 40
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 6. After a successful installation, click “Finish” to complete. YOU CAN NOW CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER. 7. Connect power to JBV-1 (11-16V DC) from external power supply, then connect USB cable between JBV-1 USB connector and PC. 8. Install or update the JBV-1 USB drivers which are delivered with the JBV-1 SW installation package.
PAGE 41
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care JBV-1 firmware update starts and shows the current status of the connected JBV1. 11.If the firmware version read from your JBV-1 is not the latest one available (v. 17 or older), it needs to be updated to version 18. To do this, click “Update Firmware”. If you simply want to check the SW version, click “Refresh Status”. 12.To update your JBV-1 to the latest version 18, choose file JBV1v18.CDE and “Open”.
PAGE 42
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 13.After a successful update, click “OK” and the current JBV-1 status is displayed. You have now updated the JBV-1 software and it is ready for use. If you have several docking stations you need to update, disconnect the power & USB cables from the previous one and connect them to the next docking station. 14.To see the current SW version, click “Refresh Status”. 15.To update the SW, click “Update Firmware”. 16.
PAGE 43
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care RF Tuning: Quick Guide for Tuning with Phoenix ■ General remarks • RF tunings must be performed in the same order as shown in this document. The order of the corresponding menu items in the service software may be different. • If baseband tunings are needed, they should be completed before the RF tunings. • Avoid unnecessary tuning. Factory tuning values are always the most accurate ones.
PAGE 44
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Service Tool Concept for RF Tuning Operations • All RF tuning operations must be carried out in the MJ-20 module jig. • Power to MJ-20 must be supplied from an external DC power supply, not from the FPS-8 prommer.
PAGE 45
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Autotuning Autotune feature is designed to align product’s RF part easier and faster. By this autotune component the product is tuned automatically. The user only needs to press ‘Tune’ and the product’s RF is tuned and results are shown to the user. Component controls all the needed RF equipment (RF generator and TX measuring device) except voltage supplier. The phone should always be in local mode.
PAGE 46
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Set Loss Figure 5: Set Loss menu Set Loss is the component for saving RF-losses (of cables and jigs) to file. These loss values are needed when you tune the phone with Phoenix (using the Autotune component). When you measure the losses you have to be very careful, because these values affect directly how well the phone is tuned. NOTE! This component is only for Autotune uses.
PAGE 47
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care RF equipment (only one of each is needed) TX/RX: CMU200 TX: Agilent E4406 (VSA series transmitter tester) Agilent E4445 (PSA series transmitter tester) Rohde&Schwarz, FSE-family of Signal Analyzers Rohde&Schwarz, FSIQ-family of Signal Analyzers RX: Agilent ESG family of RF Signal Generators Rohde&Schwarz, SME-family of Signal Generators Figure 7: Preferred setup environment Figure 8: Alternative setup environment GPIB addresses are not def
PAGE 48
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Protection Components are protected by PKD-1CS, PKD-1NS, PKD-1 and PKD-1P dongles using standard TSS protection procedure. Autotuning itself is possible with all these dongles but with PKD1P and PKD-1 dongles user is not able to set the loss. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 49
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Receiver Manual Tuning ■ Rx Channel Select Filter Calibration • Extra equipment / external RF signal is not needed. • Must be done before other Rx calibrations. • Rx channel select filter is tuned only in one band = single calibration for all bands. To start calibrating: 1. From the Tuning menu, choose “Rx Channel Select Filter Calibration”. The “Rx Channel Select Filter Calibration” window appears. 2.
PAGE 50
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 5. To end tuning, close the “Rx Channel Select Filter Calibration” window. The values are saved to phone. ■ Rx Calibration • 850 MHz tunings only for RA-4 and 900 MHz tunings only for RAE-6. • RF generator is needed. • This tuning performs Rx calibration. • Must be done separately on each band. • Calibration is automatically performed at GSM850/EGSM900 bands, then at the GSM1800 band and finally at the GSM1900 band.
PAGE 51
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 3. Set RF generator to required GSM850 frequency => OK. Tuning values and ADC readings are shown.
PAGE 52
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 4. Set RF generator to required EGSM900 frequency => OK. Tuning values and ADC readings are shown.
PAGE 53
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 5. Set RF generator to required GSM1800 frequency => OK. Tuning values and ADC readings are shown.
PAGE 54
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 6. Set the RF generator to required GSM1900 frequency => OK. Tuning values and ADC readings are shown.
PAGE 55
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ RX Band Filter Response Compensation • 850 MHz tunings only for RA-4 and 900 MHz tunings only for RAE-6. • RF generator is needed.
PAGE 56
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 3. Set the first required frequency (GSM850) and level => OK. 4. Set the 2nd required frequency and level => OK. 5. Set the 3rd required frequency and level => OK. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 57
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 6. Set the 4th required frequency and level => OK. 7. Set the 5th required frequency and level => OK. 8. Set the 6th required frequency and level => OK. 57 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 58
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 9. Set the 7th required frequency and level => OK. 10.Set the 8th required frequency and level => OK. 11.Set 9th required frequency and level => OK. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 59
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Table 5: Typical values and limits in Rx Band Filter Response Compensation (GSM850): Channel Input Frequency (MHz) Typical value Low limit (dB) High limit (dB) 118 863.26771 -0.44 -10 3.5 128 869.26771 -0.53 -3.5 3.5 140 871.66771 -0.36 -3.5 3.5 172 878.06771 0.50 -3.5 3.5 190 881.66771 -0.08 -3.5 3.5 217 887.06771 0.28 -3.5 3.5 241 891.86771 0.14 -3.5 3.5 251 893.86771 0.15 -3.5 3.5 261 895.
PAGE 60
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 14.Set the 3rd required frequency and level => OK. 15.Set the 4th required frequency and level => OK. 16.Set the 5th required frequency and level => OK. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 61
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 17.Set the 6th required frequency and level => OK. 18.Set the 7th required frequency and level => OK. 19.Set the 8th required frequency and level => OK. 61 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 62
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 20.Set 9th required frequency and level => OK. Table 6: Typical values and limits in Rx Band Filter Response Compensation (GSM900): Channel Input Frequency (MHz) Typical value Low limit (dB) High limit (dB) 965 923.26771 -1.70 -10 3.5 975 925.26771 -1.01 -3.5 3.5 987 927.66771 -0.45 -3.5 3.5 1009 932.06771 -0.52 -3.5 3.5 37 924.46771 -0.02 -3.5 3.5 90 953.06771 -0.24 -3.5 3.5 114 957.86771 -0.61 -3.
PAGE 63
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Table 7: Typical values and limits in Rx Band Filter Response Compensation (GSM1800): Channel Input Frequency (MHz) Typical value Low limit (dB) High limit (dB) 497 1802.26771 -1.95 -10 3.5 512 1805.26771 -1.20 -3.5 3.5 535 1809.86771 -0.49 -3.5 3.5 606 1824.06771 0.09 -3.5 3.5 700 1842.86771 -0.02 -3.5 3.5 791 1861.06771 -0.33 -3.5 3.5 870 1876.86771 -0.44 -3.5 3.5 885 1879.86771 -0.64 -3.5 3.
PAGE 64
RAE-6/RA-4 Nokia Customer Care Channel 3 - Service Software Instructions Input Frequency (MHz) Typical value Low limit (dB) High limit (dB) 586 1945.06771 -0.77 -3.5 3.5 661 1960.06771 -0.03 -3.5 3.5 736 1975.06771 -0.52 -3.5 3.5 794 1986.66771 -1.41 -3.5 3.5 810 1989.86771 -1.33 -3.5 3.5 835 1994.86771 -2.34 -10 3.5 25.If the values shown are within limits, click “Save & Continue” to save values to the phone. 26.
PAGE 65
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Rx DtoS balance calibration • 850 MHz tunings only for RA-4 and 900 MHz tunings only for RAE-6. • Rx DtoS balance calibration is used for calibrating DSP control word values. • Calibration must be done separately on each band. • Start Rx DtoS balance calibration at GSM850/EGSM900, then continue at GSM1800 band and finally at the GSM1900 band.
PAGE 66
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 3. To start tuning with values already saved to the phone, click OK. 4. Click Start. 5. If values shown are within limits, click Stop. 6. To save values to the phone, click Yes. 7. From the Tuning menu, choose “Rx DtoS Balance Calibration”. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 67
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 8. Click OK and Start. Tuning begins automatically at the GSM900 band. 9. To start tuning with values already saved to the phone, click OK. 10. Click Start. 67 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 68
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 11.If values shown are within limits, click Stop.. 12.To save values to the phone, click Yes. Continue tuning from GSM1800 band 13.From the Band dropdown menu, choose the correct band. 14.Repeat the same steps as for the GSM850/EGSM900 bands. 15.If values shown are within limits, click Yes to save values to the phone. Continue tuning from GSM1900 band 16.Repeat the same steps as for the GSM850/EGSM900 and GSM1800 bands. 17.
PAGE 69
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Transmitter Manual Tuning ■ Tx Power Level Tuning • 850 MHz tunings only for RA-4 and 900 MHz tunings only for RAE-6. • Power meter or spectrum analyzer is needed. • With Tx Power Level Tuning, the coefficients are adjusted for each power level. • Start power level tuning at GSM850, GSM900/EDGE, then continue at GSM1800/ EDGE band and finally at the GSM1900/EDGE band. To start Tx power level tuning at the GSM850 band: 1.
PAGE 70
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 3. Set up spectrum analyzer accordingly. Remember to take the jig and cable attenuations into account! The coefficient table lists the power level, coefficient, target dBm and DAC value for each power level. 4. To choose the tuned power level, use up and down arrows or mouse. The current power level is shown with inverse colours. The tuning value can be adjusted with “-“ and “+” keys.
PAGE 71
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 5. Tune Base level and power levels 19, 15 and 5 to target level. Table 9: Typical values: GSM850 Power level Coefficient Typical value 5 0,65 15 0,16 19 0,12 Base 0,10 Note! ‘Typical values’ above are shown as a guideline only. Slight variation from unit to unit is normal.’ 6. Click Save & Continue. Tuning values are calculated and saved to phone’s memory. 71 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 72
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Tuning continues at EDGE850 7. Set up spectrum analyzer accordingly. 8. To start tuning, click OK. 9. Tune all power levels to target level. 10.To save the tuning values to phone’s memory, click Save & Continue. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 73
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 11.From the Tuning menu, choose Tx Power Level Tuning (EGSM900). 12.Click Start. Tuning begins at the GSM900 band. 13.Set up spectrum analyzer accordingly. Remember to take the jig and cable attenuations into account! 73 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 74
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care The coefficient table lists the power level, coefficient, target dBm and DAC value for each power level. 14.To choose the tuned power level, use up and down arrows or mouse. The current power level is shown with inverse colours. The tuning value can be adjusted with “-“ and “+” keys. 15.Tune Base level and power levels 19, 15 and 5 to target level.
PAGE 75
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 16.Click Save & Continue. Tuning values are calculated and saved to phone’s memory. Tuning continues at EDGE900 17.Set up spectrum analyzer accordingly. 18.To start tuning, click OK. 75 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 76
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 19.Tune all power levels to target level. 20. To save the tuning values to phone’s memory, click Save & Continue. Tuning continues at GSM1800 band 21.Set up spectrum analyzer accordingly. Remember to take the jig and cable attenuations into account! Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 77
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 22.Click OK. 23..Tune Base level and power levels 15,11 and 0 to target level. Table 11: Typical values GSM1800 Power level 77 Coefficient Typical value 0 0,56 11 0,20 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 78
RAE-6/RA-4 3 - Service Software Instructions Power level Nokia Customer Care Coefficient Typical value 15 0,15 Base 0,10 Note! ‘Typical values’ above are shown as a guideline only. Slight variation from unit to unit is normal. 24.Click Save & Continue. Tuning values are calculated and saved to phone’s memory. Tuning continues at EDGE1800 25.Set up spectrum analyzer accordingly. 26.Click OK. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 79
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 27.Tune all power levels to target level. 28.To save the tuning values to phone’s memory, click Save & Continue. 79 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 80
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Tuning continues at GSM1900 band 29.Set up spectrum analyzer accordingly. Remember to take the jig and cable attenuations into account! 30.Click OK. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 81
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 31.Tune Base level and power levels 15, 11 and 0 to target level. Note! For RA-4 only. Use the following tuning targets: - power level 0 = 29,7 dBm - power level 1 = 27,7 dBm - power level 13 = 5,0 dBm - power level 14 = 3,5 dBm - power level 15 = 1,5 dBm. Other targets are as shown in the picture above.
PAGE 82
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 32.Click Save & Continue. Tuning values are calculated and saved to phone’s memory Tuning continues at EDGE1900 33.Set up spectrum analyzer accordingly. 34.Click OK. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 83
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 35..Tune all power levels to target level. 36.To save the tuning values to phone’s memory, click Save & Continue. TX Power Level Tuning is now completed. 83 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 84
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care ■ TX I/Q Tuning • 850 MHz tunings only for RA-4 and 900 MHz tunings only for RAE-6. • Spectrum analyzer is needed. • Tx IQ Tuning allows changing the Tx I DC Offset, Tx Q DC Offset, Amplitude difference and Phase difference. • Must be done separately on all bands! To start tuning at the GSM850 band: 1. From the Tuning menu, choose “Tx IQ Tuning”. Tx IQ Tuning window appears. 2. To begin tuning, click Start.
PAGE 85
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 3. Adjust spectrum analyzer accordingly. 4. Click OK. 5. Set each of the sliders to the desired value. The order of tuning should be the same as the order of the sliders, that is, the Tx I DC Offset is tuned first and Phase difference is tuned last. Use <= , =>, PgUp or PgDn keys. 6. Tune LO leakage to minimum with TXI/TXQ DC Offset control (f0 on spectrum analyzer screen). 85 COMPANY CONFIDENTIAL Copyright © 2004 Nokia.
PAGE 86
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 7. To tune the undesired sideband to minimum, use Amplitude/Phase difference controls (f0 + 67.71kHz on spectrum analyzer screen). LO leakage Unwanted sideband LO leakage and undesired sideband are tuned to minimum Tuning limits are the same for all bands (GSM/EDGE850, GSM/EDGE1800 and GSM/EDGE1900): Tuning limits I DC Offset Issue 1 12/04 Value -6…+6 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 87
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Tuning limits Value Q DC Offset -6…+6 Amplitude difference -1…+1 Phase difference - 80°…100° 8. When the IQ spectrum is balanced, click Next to continue EDGE850 Tx IQ tuning. Spectrum analyzer settings are the same as for GSM850 Tx IQ tuning. NOTE! In EDGE-mode, the unwanted sideband is located at 50.8kHz from f0. 50.8kHz 9. When the IQ spectrum is balanced, click Next to continue GSM1800 Tx IQ tuning.
PAGE 88
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 10.From the Tuning menu, choose “Tx IQ Tuning”. Tx IQ Tuning window appears. 11.Click Start. Tuning begins at the GSM900 band. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 89
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 12.Adjust spectrum analyzer accordingly. 13.Click OK. 14.Set each of the sliders to the desired value. The order of tuning should be the same as the order of the sliders, that is, the Tx I DC Offset is tuned first and Phase difference is tuned last. Use <= , =>, PgUp or PgDn keys. 15.Tune LO leakage to minimum with TXI/TXQ DC Offset control (f0 on spectrum analyzer screen). 89 COMPANY CONFIDENTIAL Copyright © 2004 Nokia.
PAGE 90
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 16.To tune the undesired sideband to minimum, use Amplitude/Phase difference controls (f0 + 67.71kHz on spectrum analyzer screen). Tuning limits are the same for all bands (GSM/EDGE900, GSM/EDGE1800 and GSM/EDGE1900): Tuning limits Value I DC Offset -6…+6 Q DC Offset -6…+6 Amplitude difference -1…+1 Phase difference - 80°…100° 17.When the IQ spectrum is balanced, click Next to continue EDGE900 Tx IQ tuning.
PAGE 91
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Continue tuning at GSM/EDGE1800 band 19.Adjust spectrum analyzer accordingly. Both GSM and EDGE 1800 use the same settings. Continue tuning at GSM/EDGE1900 band 20.Adjust spectrum analyzer accordingly. Both GSM and EDGE 1900 use the same settings. 91 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 92
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care 21.When GSM and EDGE 1900 are tuned, click Finish and then close the window. Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 93
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Service Tool Concept for Baseband Tuning Operations EM calibrations should be carried out in the JBV-1 docking station equipped with the DA-21 docking station adapter. Note: RF tunings must be carried out in the MJ-20 module jig. Power to JBV-1 should be supplied from an external DC power supply, not from the FPS-8 prommer.
PAGE 94
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care ■ Service concept for RAE-6/RA-4* baseband tunings 6 7 5 3 4 2 1 Item Issue 1 12/04 Accessory type Service Accessory 1 JBV-1 Docking station 2 DA-21 Docking station adapter 3 CA-5S DC cable 4 PCS-1 DC power cable 5 DAU-9S Service FBUS cable 6 PKD-1 Software protection key 7 Service SW CD-ROM COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 95
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions Baseband Tuning Operations ■ Energy Management Calibration External power supply is needed. Energy Management (EM) Calibration is used for calibrating the battery and charger settings of the phone. Preparation for EM Calibration: • Connect the DC Cable CA-5S between JBV-1 and Vin of the phone for charger calibration. • Connect 12…15 V from the power supply to JBV-1. NOTE! Check that the connection is FBUS (does not work with MBUS).
PAGE 96
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions 3. To run the selected calibrations, click Calibrate. Table 13: Limits for Energy Management Calibration Parameter Min.
PAGE 97
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care Flashing Setup Instructions ■ POS (Point of Sale) flash concept 5 4 6 2 3 1 Item Type Description 1 SF-24 Point of sales flash adapter 2 CA-28DS or XCS-1 + DKU-2 Service data cable 3 ACF-8 Universal power supply 4 FLS-4S FLS-4S sales package E&A FLS-4S FLS-4S sales package APAC FLS-4S FLS-4S sales package US 5 Standard USB cable 6 Service SW CD-ROM Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia.
PAGE 98
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions To use FLS-4S Flash Dongle you have to follow the user guide inside the sales package. Please check always for the latest version of flash software, which is available on Nokia Partner Web Site / Nokia Online. It is very important to follow this insertion and removal procedure, otherwise the contact pins of Flash Adapter will be damaged.
PAGE 99
RAE-6/RA-4 3 - Service Software Instructions 5.) Lift up the Adapter while holding the release tension. Issue 1 12/04 Nokia Customer Care 6.) Put back the Sealing Tape after the flashing procedure. COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 100
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Flash concepts with flashing adapter Figure 9: Flash concept with FPS-8 7 9 8 6 5 4 2 10 3 1 Item Type 1 SF-24 Point of sales flash adapter 2 XCS-4 Modular cable 3 FLC-2 Power cable 4 FPS-8 Flash prommer box 5 Centronics (printer) cable, incl in FPS-8 sales package 6 AXS-4 RS-232 (D9-D9) cable, incl in FPS-8 sales package 7 PKD-1 Software protection key 8 100 Description Service SW CD-ROM 9 ACF-8 AC c
PAGE 101
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care ■ MJ-20 module jig concepts Figure 10: MJ-20 module jig concept 5 4 2 6 3 1 Item Description 1 MJ-20 Module jig 2 PCS-1 DC power cable 3 XRF-1 RF antenna cable 4 DAU-9S Service FBUS cable 5 PKD-1 Software protection key 6 Issue 1 12/04 Type Service SW CD-ROM COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 102
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ JBV-1 flash concept with FPS-8 8 9 10 7 11 6 5 4 3 2 Flash FPS-8+DA-2 VP 01-09-04 1 Figure 11: JBV-1 flash concept with FPS-8 Item Type 1 JBV-1 Docking station 2 DA-21 Docking station adapter 3 PCS-1 DC power cable 4 XCS-4 Modular cable 5 FPS-8 Flash prommer box 7 AXS-4 D9 – D9 cable, incl.
PAGE 103
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care ■ JBV-1 flash concept with FPS-10 8 9 10 7 6 5 4 3 2 Flash FPS-10+DAVP 01-09-04 1 Figure 12: JBV-1 flash concept with FPS-10 Item Type 1 JBV-1 Docking station 2 DA-21 Docking station adapter 3 CA-41PS DC power cable 4 XCS-4 Modular cable 5 FPS-8 Flash prommer box 6 DKU-2 Connectivity cable 7 AXS-4 D9 – D9 cable, incl.
PAGE 104
RAE-6/RA-4 Nokia Customer Care 3 - Service Software Instructions ■ Service concept for RF testing and BB tuning Note! RF tuning not allowed with RF coupler SA-61! Item Type 1 JBV-1 Docking station 2 DA-21 Docking station adapter 3 SA-61 RF-coupler 4 PCS-1 DC power cable 5 DAU-9S Service FBUS cable 6 PKD-1 Software protection key 7 8 104 Description Service SW CD-ROM XRF-1 RF cable COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.
PAGE 105
RAE-6/RA-4 3 - Service Software Instructions Nokia Customer Care ■ Bluetooth test concept 3 4 2 6 5 NO KI A 1 Item Type Description 1 SF-24 Point of sales flash adapter 2 DAU-9S Service FBUS cable 3 PKD-1 Software protection key 4 Service SW CD-ROM 5 JBT-9 Bluetooth test box 6 ACP-8E (for Europe) ACP-8U (for U.S.) Charger for JBT-9 Issue 1 12/04 COMPANY CONFIDENTIAL Copyright © 2004 Nokia. All Rights Reserved.