Nokia 7390 User Guide
DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION declares that this RM-140 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/declaration_of_conformity/. 0434 The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of life.
Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. This device complies with Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
Contents Contents For your safety.......................... 6 General information................. 9 Access codes............................................ 9 Configuration settings service ........ 10 Download content .............................. 10 Nokia support....................................... 10 1. Get started ......................... 11 Install SIM card and battery ............ Insert a microSD card ........................ Charge the battery..............................
Contents Time and date....................................... My shortcuts......................................... Connectivity .......................................... Call........................................................... Phone ...................................................... Configuration........................................ Security .................................................. Digital rights management............... Restore factory settings.....................
For your safety For your safety Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information. SWITCH ON SAFELY Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. ROAD SAFETY COMES FIRST Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.
For your safety WATER-RESISTANCE Your phone is not water-resistant. Keep it dry. BACK-UP COPIES Remember to make back-up copies or keep a written record of all important information stored in your phone. CONNECTING TO OTHER DEVICES When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products. EMERGENCY CALLS Ensure the phone is switched on and in service.
For your safety services. For instance, some networks may not support all languagedependent characters and services. Your service provider may have requested that certain features be disabled or not activated in your device. If so, they will not appear on your device menu. Your device may also have been specially configured for your network provider. This configuration may include changes in menu names, menu order and icons. Contact your service provider for more information. This device supports WAP 2.
General information General information ■ Access codes Security code The security code (5 to 10 digits) helps to protect your phone against unauthorized use. The preset code is 12345. To change the code, and to set the phone to request the code, see “Security,” p. 63. PIN codes The personal identification number (PIN) code and the universal personal identification number (UPIN) code (4 to 8 digits) help to protect your SIM card against unauthorized use. See “Security,” p. 63.
General information ■ Configuration settings service To use some of the network services, such as mobile Internet services, MMS, Nokia Xpress audio messaging, or remote Internet server synchronization, your phone needs the correct configuration settings. For more information on availability, contact your network operator, service provider, nearest authorized Nokia dealer, or visit the support area on the Nokia Web site, www.nokia.com/support.
Get started 1. Get started ■ Install SIM card and battery Always switch the device off and disconnect the charger before removing the battery. Keep all SIM cards out of the reach of small children. For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider, network operator, or other vendor. This device is intended for use with BP-5M battery. Always use original Nokia batteries. See “Nokia battery authentication,” p. 100.
Get started Replace the battery (6). Place the back cover into its place (7). Make sure it clicks into place, so that the back cover release slide resumes its normal position(8). ■ Insert a microSD card Keep all microSD memory cards out of the reach of small children. A microSD card can be loaded with ringing tones, themes, tones, images and videos. If you delete, reload, or replace this card, these functions and features may not function properly. Use only compatible microSD cards with this device.
Get started 1. Remove the back cover of the phone. Swing the microSD memory card holder open (1) 2. Insert the card into the memory card holder with the gold-colored contact area facing up (2). 3. Close the card holder (3 and 4) and slide the back cover back in place. ■ Charge the battery Check the model number of any charger before use with this device. This device is intended for use when supplied with power from an AC-3 or AC-4 charger.
Get started The charging time depends on the charger used. Charging a BP-5M battery with the AC-3 charger takes approximately 2 hours and 20 minutes while the phone is in the standby mode. ■ Open and close the phone You open and close the phone manually. When you open the fold of the phone, it opens up to appromiximately 155 degrees. Do not try to force the fold open more. Depending on the Theme a tone sounds when you open and close the phone.
Get started ■ Antenna Your device has an internal antenna. Note: As with any other radio transmitting device, do not touch the antenna unnecessarily when the device is switched on. Contact with the antenna affects call quality and may cause the device to operate at a higher power level than otherwise needed. Avoiding contact with the antenna area when operating the device optimizes the antenna performance and the battery life. ■ Phone strap Remove the back cover of the phone.
Your phone 2.
Your phone 19 Camera lens 20 Camera flash 21 Phone strap eyelet 22 USB port 23 Headset connector 24 Charger connector 25 Power key 26 Infrared port 17
Your phone ■ Standby mode When the phone is ready for use, and you have not entered any characters, the phone is in the standby mode.
Your phone 10 The right selection key may be Names to access the list of contacts in the Contacts menu, an operator-specific name to access an operator-specific Web site, or a shortcut to a function that you selected. See “Right selection key,”p. 54. Active standby In the active standby mode there is a list of selected phone features and information on the screen that you can directly access in the standby mode.
Your phone , The phone is registered to the GPRS or EGPRS network. , A GPRS or EGPRS connection is established. , The GPRS or EGPRS connection is suspended (on hold). A Bluetooth connection is active. Push to talk connection is active or suspended. , If you have two phone lines, the second phone line is selected. All incoming calls are diverted to another number. The loudspeaker is activated, or the music stand is connected to the phone. Calls are limited to a closed user group.
Your phone ■ Keypad lock (keyguard) Select Menu or Unlock and then press the * key within 1.5 seconds to lock or unlock the keypad. If the security keyguard is activated, enter the security code if requested. To answer a call when the keyguard is on, press the call key or open the phone. When you end or reject the call, the keypad automatically locks. For Security keyguard, see “Phone,” p. 61. When the keyguard is on, calls still may be possible to the official emergency number programmed into your device.
Call functions 3. Call functions ■ Make a voice call 1. Enter the phone number, including the area code. For international calls, press * twice for the international prefix (the + character replaces the international access code), enter the country code, the area code without the leading 0, if necessary, and the phone number. 2. To call the number, press the call key. To increase the volume in a call, press the volume up key and to decrease press the volume down key. 3.
Call functions Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely upon voice dialing in all circumstances. 1. In the standby mode, press and hold the right selection key or press and hold the volume down key. A short tone is played, and Speak now is displayed. 2. Say the voice command clearly. If the voice recognition was successful, a list with matches is shown. The phone plays the voice command of the match on the top of the list.
Call functions Call options are Mute or Unmute, Contacts, Menu, Lock keypad, Record, Loudspeaker or Handset.
Call functions The video call is active when you can see two video images and hear the sound through the loudspeaker. The call recipient may deny the video sending, in which case you may see a still image or a grey background graphic. You will hear the sound. 3. To end the call, press the end key. ■ Answer or reject a video call When a video call arrives, Video Call is displayed. 1. Press the call key to answer the video call. Allow video image to be sent to caller? is displayed.
Call functions your display shows Start sharing video? , press Yes and the phone starts sending the video. Audio is routed to the loudspeaker. To pause video sharing press Pause. The middle selection key is changed to Continue. To resume the video sharing press Continue. The middle selection key is changed to Pause. To end a video sharing session press Stop, and Video sharing ended is shown to both participants.
Write text 4. Write text You can enter text (for example, when writing messages) using traditional or predictive text input. When you write text, press and hold Options to toggle between traditional text input, indicated by , and predictive text input, indicated by . Not all languages are supported by predictive text input. The character cases are indicated by , , and . To change the character case, press #. To change from the letter to number mode, indicated by , press and hold #, and select Number mode.
Write text If the ? character is displayed after the word, the word you intended to write is not in the dictionary. To add the word to the dictionary, select Spell. Enter the word using traditional text input, and select Save. To write compound words, enter the first part of the word, and press the scroll key right to confirm it. Write the last part of the word, and confirm the word. 3. Start writing the next word.
Navigate the menus 5. Navigate the menus The phone offers you an extensive range of functions, which are grouped into menus. 1. To access the menu, select Menu. To change the menu view, select Options > Main menu view > List, Grid, Grid with labels, or Tab. To rearrange the menu, scroll to the menu you want to move, and select Options > Organise > Move. Scroll to where you want to move the menu, and select OK. To save the change, select Done > Yes. 2.
Messaging 6. Messaging You can read, write, send, and save text, multimedia, e-mail, audio, flash messages and postcards. All messages are organized into folders. ■ Text message (SMS) With the short message service (SMS) you can send and receive text messages, and receive messages that can contain pictures (network service). Before you can send any text or SMS e-mail messages, you must save your message center number. See “Message settings,” p. 43.
Messaging 5. To send the message, select Send. See “Message sending,”p. 32. Read and reply to a message 1. To view a received message, select Show. To view it later, select Exit. To read the message later, select Menu > Messaging > Inbox. 2. To reply to a message, select Reply > Text message, Multimedia, Flash message, or Audio message. Write the reply message. 3. To send the message, select Send. See “Message sending,” p. 32.
Messaging Write and send a multimedia plus message The wireless network may limit the size of MMS messages. If the inserted image exceeds this limit, the device may make it smaller so that it can be sent by MMS. 1. Select Menu > Messaging > Create message > Multimedia plus. 2. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address from a memory, select Add. 3. Enter a subject and write your message. 4. To add a file, select Insert. 5.
Messaging Read and reply to a message Important: Exercise caution when opening messages. Multimedia message objects may contain malicious software or otherwise be harmful to your device or PC. 1. To view a received message, select Show. To view it later, select Exit. 2. To view the whole message if the received message contains a presentation, select Play. To view the files in the presentation or the attachments, select Options > Objects or Attachments. 3.
Messaging ■ Flash messages Flash messages are text messages that are instantly displayed upon reception. Flash messages are not automatically saved. Write a message Select Menu > Messaging > Create message > Flash message. Enter the recipient’s phone number and write your message. To insert a blinking text into the message, select Options > Insert blink charact. to set a marker. The text behind the marker blinks until a second marker is inserted.
Messaging Listen to a message To open a received audio message, select Play. If more than one message is received, select Show > Play. To listen to the message later, select Exit. ■ Memory full When you receive a message, and the memory for the messages is full, Memory full. Unable to receive messages. is shown. To first delete old messages, select OK > Yes and the folder. Scroll to the desired message, and select Delete. If more messages are to be deleted, select Mark.
Messaging application is different from the SMS e-mail function. To use the e-mail function on your phone, you need a compatible e-mail system. You can write, send, and read e-mail with your phone. Your phone supports POP3 and IMAP4 e-mail servers. This application does not support keypad tones. Before you can send and retrieve any e-mail messages, you must obtain a new e-mail account or use your current account. To check the availability of your e-mail account, contact your e-mail service provider.
Messaging 3. Enter the recipient’s e-mail address, write the subject, and enter the e-mail message. To attach a file from Gallery, select Options > Attach file. 4. To send the e-mail message, select Send > Send now. To save the e-mail in the Outbox folder to be sent later, select Send > Send later. To edit or continue writing your e-mail later, select Options > Save as draft. The e-mail is saved in Outboxes > Drafts.
Messaging E-mail folders Your phone saves e-mail that you have downloaded from your e-mail account in the Inboxes folder. The Outboxes folder contains the following folders: “Account name” for incoming e-mail, Archive for archiving e-mail, Custom 1—Custom 3 for sorting e-mail, Junk where all spam e-mail is stored, Drafts for saving unfinished e-mail, Outbox for saving e-mail that has not been sent, and Sent items for saving e-mail that has been sent.
Messaging connection settings for IM service is available, select the one you want. Select from the following options: Login — to connect to the IM service. To set the phone to automatically connect to the IM service when you switch on the phone; in the login session, select Automatic login: > On, or select Menu > Messaging > IMs, connect to the IM service, and select Options > Settings > Automatic login > On.
Messaging The icons and texts on the display depends on the IM service. Online — shows the number of contacts that are online Offline — shows the number of contacts that are offline To start a conversation, expand the Online or the Offline folder and scroll to the contact with whom you would like to chat and select Chat. To answer an invitation or to reply to a message expand the Conversations folder and scroll to the contact to whom you would like to chat and select Open.
Messaging New messages received during an active conversation are held in IMs > Conversations. If you receive a message from someone who is not in IM contacts, the sender ID is displayed. To save a new contact that is not in the phone memory, select Options > Save contact. Participate in a conversation To join or start an IM session, write your message; and select Send.
Messaging Public You can bookmark public groups that your service provider may maintain. Connect to the IM service, and select Groups > Public groups. Select a group, andJoin. If you are not in the group, enter your screen name as your nickname for the group. To delete a group from your list, select Options > Delete group. To search for a group, select Groups > Public groups > Search groups. Private Connect to the IM service, and from the main menu select Options > Create group.
Messaging ■ Delete messages To delete messages, select Menu > Messaging > Delete messages > By message to delete single messages, By folder to delete all messages from a folder, or All messages. ■ SIM messages SIM messages are specific text messages that are saved to your SIM card. You can copy or move those messages to the phone memory, but not vice versa. To read SIM messages, select Menu > Messaging > Options > SIM messages.
Messaging Delivery reports > Yes — to ask the network to send delivery reports about your messages (network service) Message centres > Add centre — to set the phone number and name of the message center that is required for sending text messages. You receive this number from your service provider. Msg. centre in use — to select the message center in use E-mail msg. centres > Add centre — to set the phone numbers and name of the e-mail center for sending SMS e-mails.
Messaging Image size (MMS) — to set the image size in multimedia messages. Default slide timing — to define the default time between slides in multimedia messages Allow MMS receptn. — to receive or block the multimedia message, select Yes or No. If you select In home network, you cannot receive multimedia messages when outside your home network. The default setting of the multimedia message service is generally In home network. The availability of this menu depends on your phone. Incoming MMS msgs.
Messaging Login information — to enter authentication information used when retrieving incoming e-mail Incoming mail sett. — to enter the number of mails that shall be retrieved in maximum Outgoing sett. (SMTP) — to enter SMTP (simple mail transfer protocol) information and setting options used when sending e-mail Displ. term.
Contacts 7. Contacts You can save names and phone numbers (contacts) in the phone memory and in the SIM card memory. The phone memory may save contacts with additional details, such as various phone numbers and text items. You can also save an image for a limited number of contacts. The SIM card memory can save names with one phone number attached to them. The contacts saved in the SIM card memory are indicated by . ■ Search for a contact Select Menu > Contacts > Names.
Contacts ■ Copy or move contacts You can move and copy contacts from the phone memory to the SIM card memory, or vice versa. The SIM card can save names with one phone number attached to them. To move or copy contacts one by one, select Menu > Contacts > Names. Scroll to the contact, and select Options > Move contact or Copy contact. To move or copy marked contacts, select Menu > Contacts > Names. Scroll to a contact, and select Options > Mark.
Contacts To delete a number, text item, or an image attached to the contact, search for the contact, and select Details. Scroll to the desired detail, and select Options > Delete and from the options available. ■ Business cards You can send and receive a person’s contact information from a compatible device that supports the vCard standard as a business card. To send a business card, search for the contact whose information you want to send, and select Details > Options > Send business card.
Contacts ■ Speed dials To assign a number to a speed-dialing key, select Menu > Contacts > Speed dials, and scroll to the speed-dialing number that you want. Select Assign, or if a number has already been assigned to the key, select Options > Change. Select Search and the contact you want to assign. If the Speed dialling function is off, the phone asks whether you want to activate it. See also Speed dialling in “Call,” p. 60. To make a call using the speed-dialing keys, see “Speed dialing,” p. 22.
Log 8. Log The phone registers your missed, received, and dialed calls if the network supports it and the phone is switched on and within the network service area. To view the information on your calls, select Menu > Log > Missed calls, Received calls, or Dialled numbers. To view your recent missed and received calls and the dialed numbers chronologically, select Call log. To view the contacts to whom you most recently sent messages, select Msg. recipients.
Settings 9. Settings ■ Profiles Your phone has various settings groups called profiles, for which you can customize the phone tones for different events and environments. Select Menu > Settings > Profiles, the desired profile and from the following options: Activate — to activate the selected profile Personalise — to personalize the profile. Select the setting you want to change, and make the changes. Timed — to set the profile to be active until a certain time up to 24 hours, and set the end time.
Settings If you select the highest ringing tone level, the ringing tone reaches its highest level after a few seconds. ■ Main Display Select Menu > Settings > Main display and from the available options: Wallpaper — to add the background image in the standby mode Active standby — to switch the active standby mode on or off and to organize and personalize the active standby mode.
Settings ■ Time and date To change the time, time zone, and date settings, select Menu > Settings > Time and date > Time, Date, or Auto-update of time (network service). When traveling to a different time zone, select Menu > Settings > Time and date > Time > Time zone and the time zone of your location in terms of the time difference with respect to Greenwich Mean Time (GMT) or Universal Time Coordinated (UTC).
Settings Navigation key To assign other phone functions from a predefined list to the navigation key (scroll key), select Menu > Settings > My shortcuts > Navigation key. Voice commands To call contacts and carry out phone functions, say the voice commands. Voice commands are language-dependent. To set the language, see Voice playback lang. in “Phone,” p. 61. To select the phone functions to activate with voice commands, select Menu > Settings > My shortcuts > Voice commands and a folder.
Settings supporting Bluetooth technology, use Nokia approved enhancements for this model. Check with the manufacturers of other devices to determine their compatibility with this device. There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider. Features using Bluetooth technology or allowing such features to run in the background while using other features, increase the demand on battery power and reduce the battery life.
Settings Bluetooth wireless connection Select Menu > Settings > Connectivity > Bluetooth. To check which Bluetooth connection is currently active, select Active devices. To view a list of Bluetooth devices that are currently paired with the phone, select Paired devices. Bluetooth settings To define how your phone is shown to other Bluetooth devices, select Menu > Settings > Connectivity > Bluetooth > Bluetooth settings > My phone's visibility or My phone's name.
Settings Packet data (GPRS) General packet radio service (GPRS) is a network service that allows mobile phones to send and receive data over an Internet protocol (IP)-based network. To define how to use the service, select Menu > Settings > Connectivity > Packet data > Packet data conn. and from the following options: When needed — to set the packet data connection to established when an application needs it. The connection will be closed when the application is terminated.
Settings Your phone allows data transfer with a compatible PC or another compatible device when using the phone without a SIM card. Transfer contact list To copy or synchronize data from your phone, the name of the device and the settings must be in the list of transfer contacts. If you receive data from another device (for example, a compatible mobile phone), the corresponding transfer contact is automatically added to the list, using the contact data from the other device.
Settings Synchronize from a server To use a remote Internet server, subscribe to a synchronization service. For more information and the settings required for this service, contact your service provider. You may receive the settings as a configuration message. See “Configuration settings service,” p. 10 and “Configuration,” p. 63. To start the synchronization from your phone, select Menu > Settings > Connectivity > Data transfer > Server sync.
Settings Call divert — to divert your incoming calls (network service). You may not be able to divert your calls if some call barring functions are active. See Call barring service in “Security,” p. 63.
Settings Language settings — to set the display language of your phone, select Phone language. Automatic selects the language according to the information on the SIM card. To select the USIM card language, select SIM language. To set a language for the voice playback, select Voice playback lang.. See “Enhanced voice dialing,” p. 22 and Voice commands in “My shortcuts,” p. 54.
Settings ■ Configuration You can configure your phone with settings that are required for certain services to function correctly. Your service provider may also send you these settings. See “Configuration settings service,” p. 10. Select Menu > Settings > Configuration and from the following options: Default config. sett. — to view the service providers saved in the phone. To set the configuration settings of the service provider as default settings, select Options > Set as default. Activ. def.
Settings PIN code request and UPIN code request — to set the phone to ask for your PIN or UPIN code every time the phone is switched on. Some SIM cards do not allow the code request to be turned off. PIN2 code request — to select whether the PIN2 code is required when using a specific phone feature which is protected by the PIN2 code. Some SIM cards do not allow the code request to be turned off. Call barring service — to restrict incoming calls to and outgoing calls from your phone (network service).
Settings ■ Digital rights management Digital rights management (DRM) is copyright protection, designed to prevent modification and to limit distribution of protected files. When you download protected files, such as sound, video, themes, or ringing tones to your phone, the files are free, but locked. You pay for the key to activate the file, and the activation key is automatically sent to your phone when you download the file.
Operator menu 10. Operator menu This menu lets you access a portal to services provided by your network operator. The name and the icon depend on the operator. For more information contact your network operator. The operator can update this menu with a service message. For more information, see “Service inbox,” p. 93.
Gallery 11. Gallery In this menu you can manage images, video clips, music files, themes, graphics, tones, recordings, and received files. These files are stored in the phone memory or an attached microSD memory card and may be arranged in folders. Your phone supports an activation key system to protect acquired content. Always check the delivery terms of any content and activation key before acquiring them, as they may be subject to a fee.
Gallery You can use the microSD memory card to store your multimedia files such as video clips, music tracks, and sound files, images, and messaging data, and to back up information from phone memory. Some of the folders in Gallery with content that the phone use, for example, Themes, may be stored on a memory card. To insert and remove the microSD memory card see “Insert a microSD card,” p. 12. Format the memory card When a memory card is formatted, all data on the card is permanently lost.
Media 12. Media When taking and using images or video clips, obey all laws and respect local customs as well as privacy and legitimate rights of others, including copyrights. You can take photos or record live video clips with the built-in 3 megapixel camera with autofocus. ■ Camera The camera produces pictures in .jpg format, and you can digitally zoom up to eight times. Take a photo To open the camera viewfinder, select Menu > Media > Camera. You can also take a photo when the phone is folded.
Media Your device supports an image capture resolution of 1536 x 2048 pixels. Camera and video options To use a filter, select Options > Effects > Normal, Greyscale, Sepia, Negative. To change the camera and video settings, select Options > Settings. ■ Video You can record video clips in .3gp format. Available recording time depends on the video clip length and quality settings. The length and file size of the clips may vary depending on the selected quality and available memory.
Media Select Menu > Media > Media player > Open gallery, Bookmarks, Go to address, or Media downloads to select or download media. Select Menu > Media > Media player > FF/Rew interval to set the step width for fast forward or rewind. Configuration for a streaming service You may receive the configuration settings required for streaming as a configuration message from the service provider. See “Configuration settings service,” p. 10. You can also enter the settings manually. See “Configuration,” p. 63.
Media Operate the music player with the keys on the phone or with the virtual keys on the display. When you open the Music player menu, the details of the first track on the default track list are shown. To play, select . To adjust the volume level, use the volume keys on the side of the phone. To pause the playing, select . To stop the playing, press and hold the end key To skip to the next track, select previous track, select . .
Media Use tone — Set the the currently played music track, for example, as ringing tone. Web page — to access a Web page associated with the currently played track. Dimmed if no Web page is available. Music downloads— to connect to a browser service related to the current track. This function is only available when the address of the service is included in the track. ■ Radio The FM radio depends on an antenna other than the wireless device’s antenna.
Media Listen to the radio Select Menu > Media > Radio. To scroll to the desired frequency, select or , or press the headset key. To select a radio station, briefly press the corresponding number keys. To adjust the volume, press the volume keys. Select from the following options: Switch off — to turn off the radio Save station — to save a new station (shown if a new station is detected) Loudspeaker or Headset — to listen to the radio using the loudspeaker or headset.
Media The recorder cannot be used when a data call or GPRS connection is active. Record sound 1. Select Menu > Media > Voice recorder. To use the graphical keys , , or on the display, scroll left or right to the desired key, and select it. 2. To start the recording, select . To start the recording during a call, select Options > Record. While recording a call, all parties to the call hear a faint beeping sound. When recording a call, hold the phone in the normal position near to your ear.
Organizer 13. Organizer ■ Alarm clock You can set the phone to alarm at a desired time. Select Menu > Organiser > Alarm clock. To set the alarm, select Alarm time, and enter the alarm time. To change the alarm time when the alarm time is set, select On. To set the phone to alert you on selected days of the week, select Repeat alarm. To select the alarm tone or set the radio as the alarm tone, select Alarm tone. If you select the radio as an alarm tone, connect the headset to the phone.
Organizer calendar, select the month or week view, and select Options > Delete all notes. In Settings you can set the date, time, time zone, date or time format, date separator, default view, or the first day of the week. In Auto-delete notes you can set the phone to delete old notes automatically after a specified time. Make a calendar note Select Menu > Organiser > Calendar.
Organizer To make a note if no note is added, select Add; otherwise, select Options > Make a note. Write the note, and select Save. ■ Calculator The calculator in your phone provides basic arithmetic and trigonometric functions, calculates the square and the square root, the inverse of a number, and converts currency values. Note: This calculator has limited accuracy and is designed for simple calculations. Select Menu > Organiser > Calculator.
Organizer ■ Stopwatch You can measure time, take intermediate times, or take lap times using the stopwatch. During timing, the other functions of the phone can be used. To set the stopwatch timing in the background, press the end key. Using the stopwatch or allowing it to run in the background when using other features increases the demand on battery power and reduces the battery life. Select Menu > Organiser > Stopwatch and from the following options: Split timing — to take intermediate times.
Push to talk 14. Push to talk Select Menu > Push to talk. Push to talk (PTT) over cellular is a two-way radio service available over a GPRS cellular network (network service). You can use PTT to have a conversation with one person or with a group of people (channel) having compatible devices. While you are connected to the PTT service, you can use the other functions of the phone. To check availability and costs, and to subscribe to the service, contact your network operator.
Push to talk Create a channel To add a channel, select Menu > Push to talk > Add channel and enter the settings in the form fields: Channel name: — Enter a name for the new channel. Channel status: — Select Active to set the channel active, or Inactive to disable the channel. Nickname in channel: — Enter your nick name to be shown the new channel.
Push to talk ■ Switch PTT on and off To connect to the PTT service, select Menu > Push to talk > Switch PTT on, or press and hold the PTT (volume up) key. indicates the PTT connection. indicates that the service is temporarily unavailable. If you have added channels to the phone, you are automatically joined to the active channels. You may assign a default function to the PTT (volume up) key to open the channel list, the contacts list or a single channel or contact. See “PTT settings,” p. 85.
Push to talk Make a one-to-one call To start a one-to-one call from the list of contacts to which you have added the PTT address, select Contacts > Names or Menu > Push to talk > Contacts list. Scroll to a contact, and press and hold the PTT (volume up) key. To start a one-to-one call from the list of PTT channels, select Channel list, scroll to the desired channel, and select Members. Scroll to the desired contact, and press and hold the PTT (volume up) key.
Push to talk When you press and hold the PTT (volume up) key while the caller is talking, you hear a queuing tone, and Queuing is displayed. Press and hold the PTT (volume up) key, and wait for the other person to finish; then you can talk immediately. ■ Callback requests If you make a one-to-one call and do not get a response, you can send a request for the person to call you back.
Push to talk To delete the request, select Delete. To save a new contact or to add the PTT address to a contact from a received callback request, select Options > Save as or Add to contact. ■ Add a one-to-one contact You can save the names of persons to whom you often make one-toone calls in the following ways: To add a PTT address to a name in Contacts, search for the desired contact, select Details > Options > Add detail > PTT address.
Push to talk PTT status in startup > Yes or Ask first— to set the phone to automatically connect to the PTT service when you switch the phone on PTT when abroad — to switch the PTT service on or off when the phone is used outside of the home network Send my PTT address > No — to hide your PTT address from channel and one-to-one calls ■ Configuration settings You may receive the settings for connecting to the service from your service provider. See “Configuration settings service,” p. 10.
Applications 15. Applications In this menu you can manage applications and games. These files are stored in the phone memory or an attached microSD memory card and may be arranged in folders. For options to format or lock and unlock the memory card see “Memory card,” p. 67. ■ Launch a game Your phone software includes some games. Select Menu > Applications > Games. Scroll to the desired game, and select Open.
Applications ■ Download an application Your phone supports J2ME Java applications. Make sure that the application is compatible with your phone before downloading it. Important: Only install and use applications and other software from sources that offer adequate security and protection against harmful software. You can download new Java applications and games in different ways.
SIM services 16. SIM services Your SIM card may provide additional services. You can access this menu only if it is supported by your SIM card. The name and contents of the menu depend on the available services. For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider, network operator, or other vendor.
Web 17. Web You can access various mobile Internet services with your phone browser. Important: Use only services that you trust and that offer adequate security and protection against harmful software. Check the availability of these services, pricing, tariffs, and instructions with your service provider. With the phone browser you can view the services that use wireless markup language (WML) or extensible hypertext markup language (XHTML) on their pages. Appearance may vary due to screen size.
Web Make a connection to the service in one of the following ways: • Select Menu > Web > Home; or in the standby mode, press and hold 0. • To select a bookmark of the service, select Menu > Web > Bookmarks. • To select the last URL, select Menu > Web > Last web addr.. • To enter the address of the service, select Menu > Web > Go to address. Enter the address of the service, and select OK. ■ Browse pages After you make a connection to the service, you can start browsing its pages.
Web 3. Select Options to view, edit, delete, or send the bookmark; to create a new bookmark; or to save the bookmark to a folder. Your device may have some bookmarks loaded for sites not affiliated with Nokia. Nokia does not warrant or endorse these sites. If you choose to access them, you should take the same precautions, for security or content, as you would with any Internet site. Receive a bookmark When you have received a bookmark that is sent as a bookmark, 1 bookmark received is displayed.
Web ■ Security settings Cookies A cookie is data that a site saves in the cache memory of your phone. Cookies are saved until you clear the cache memory. See “Cache memory,” p. 94. While browsing, select Options > Other options > Security > Cookie settings; or in the standby mode, select Menu > Web > Settings > Security settings > Cookies. To allow or prevent the phone from receiving cookies, select Allow or Reject.
Web activate the browser and download the marked content, select Retrieve. To display detailed information on the service notification or to delete the message, select Options > Details or Delete. Service inbox settings Select Menu > Web > Settings > Service inbox sett.. To set whether you want to receive service messages, select Service messages > On or Off. To set the phone to receive service messages only from content authors approved by the service provider, select Message filter > On.
Web Security module The security module improves security services for applications requiring a browser connection, and allows you to use a digital signature. The security module may contain certificates as well as private and public keys. The certificates are saved in the security module by the service provider. To view or change the security module settings, select Menu > Settings > Security > Security module sett..
Web Digital signature You can make digital signatures with your phone if your SIM card has a security module. Using the digital signature can be the same as signing your name to a paper bill, contract, or other document. To make a digital signature, select a link on a page, for example, the title of the book you want to buy and its price. The text to sign, which may include the amount and date, is shown. Check that the header text is Read and that the digital signature icon is shown.
PC connectivity 18. PC connectivity You can send and receive e-mail, and access the Internet when your phone is connected to a compatible PC through a Bluetooth or a data cable connection. You can use your phone with a variety of PC connectivity and data communications applications. ■ Nokia PC Suite With Nokia PC Suite you can synchronize contacts, calendar, notes, and to-do notes between your phone and the compatible PC or a remote Internet server (network service).
PC connectivity ■ Data communication applications For information on using a data communication application, refer to the documentation provided with it. Making or answering phone calls during a computer connection is not recommended, as it might disrupt the operation. For better performance during data calls, place the phone on a stationary surface with the keypad facing downward. Do not move the phone by holding it in your hand during a data call.
Battery information 19. Battery information ■ Charging and discharging Your device is powered by a rechargeable battery. The full performance of a new battery is achieved only after two or three complete charge and discharge cycles. The battery can be charged and discharged hundreds of times, but it will eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery.
Battery information ■ Nokia battery authentication Always use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from an authorized Nokia dealer, look for the Nokia Original Enhancements logo on the packaging, and inspect the hologram label using the following steps: Successful completion of the four steps is not a total assurance of the authenticity of the battery.
Battery information 4. Confirm that the 20-digit code is valid by following the instructions at www.nokia.com/ batterycheck. To create a text message enter the 20-digit code, for example, 12345678919876543210, and send to +44 7786 200276. To create a text message, • For countries in Asia Pacific, excluding India: Enter the 20-digit code, for example, 12345678919876543210, and send to +61 427151515.
Care and maintenance Care and maintenance Your device is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you protect your warranty coverage. • Keep the device dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery and allow the device to dry completely before replacing it.
Care and maintenance All of the above suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service facility for service.
Additional safety information Additional safety information Your device and its enhancements may contain small parts. Keep them out of the reach of small children. ■ Operating environment Remember to follow any special regulations in force in any area, and always switch off your device when its use is prohibited or when it may cause interference or danger. Use the device only in its normal operating positions.
Additional safety information recommendations of Wireless Technology Research. Persons with pacemakers should do the following: • Always keep the device more than 15.3 centimeters (6 inches) from the pacemaker • Not carry the device in a breast pocket • Hold the device to the ear opposite the pacemaker to minimize the potential for interference. If you suspect interference, switch off your device, and move the device away. Hearing aids Some digital wireless devices may interfere with some hearing aids.
Additional safety information your vehicle engine. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refueling points such as near gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often but not always clearly marked.
Additional safety information ■ Certification information (SAR) This mobile device meets guidelines for exposure to radio waves Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health.
Index Index A access codes 9 accessories. See enhancements.
Index messages 43 digital rights management 65 digital signature 96 display 16, 18 downloading protected files 65 downloads 10, 93 IR 57 E keyguard 21 keypad 16 keypad lock 21 keys call key 16 end key 16 keyguard 21 keypad 16 keypad lock 21 navigation key 16 selection keys 16 earpiece 16 EGPRS 58 e-mail application 35 emergency calls 106 end call 22 key 16 enhancements 8 equalizer 75 explosive environments 105 F factory settings 65 flash messages 34 FM radio 73 font size 53 G gallery 67 games 87 GPRS
Index service commands 42 text 30 voice message 42 mini display 18 MMS. See multimedia messages.
Index restore factory settings 65 security 63 service inbox 94 themes 52 time 54 tones 52 USB data cable 60 wallpaper 53 shared memory 8 shortcuts 54 signal strength 18 SIM card 21 card installation 11 messages 43 services 89 SMS.
