CCS Technical Documentation NSB-9 Series Transceivers Service Software Instructions Draft 1 02/03 Copyright Nokia. All rights reserved.
NSB-9 Service Software Instructions CCS Technical Documentation [This page left intentionally blank] Page 2 Copyright Nokia. All rights reserved.
NSB-9 CCS Technical Documentation Quick Guide for Phoenix Service SW Installation ........................................................ 5 Phoenix Installation Steps in Brief ..............................................................................5 Phoenix Service SW....................................................................................................... 6 Before Installation .......................................................................................................
NSB-9 CCS Technical Documentation Page 2 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation Quick Guide for Phoenix Service SW Installation Phoenix Installation Steps in Brief DCT-4 generation Test and Service Software is called “Phoenix” These are the basic steps to install the Phoenix • Install the Phoenix Service SW • Install the Data Package for Phoenix (product specific data and flash update package) • Manage connection settings (depends on the tools you are using) • Update FPS-8 SW (if you use FPS-8) • Activate FPS-8 • Upd
NSB-9 Company confidential CCS Technical Documentation Phoenix Service SW Before Installation • Check that a Dongle is attached to the parallel port of your computer. • Download the installation package (e.g. phoenix_service_sw_a3_03_83_005.exe) to your computer (e.g. C:\TEMP) • Close all other programs • Run the application file (e.g. phoenix_service_sw_a3_03_83_005.
Company confidential NSB-9 CCS Technical Documentation Startup Run the phoenix_service_sw_a3_03_83_005.exe to start installation. When you choose “Next” the files needed for installation will be extracted. Kindly wait. If the setup files are already extracted (left in the file system from previous installation) following dialog appears. Always click "Yes to All" to overwrite the existing setup files. Issue 1 04/03 Copyright Nokia. All rights reserved.
NSB-9 Company confidential CCS Technical Documentation Dongle Driver Installation and Version Check If there is no previously installed Dongle driver, installation will take place... If the Dongle driver is installed and it is older than the latest supported version, the latest version will be installed when you choose “Yes”. The latest version is always included in the latest Phoenix installation package. PC needs to be rebooted before installation can continue. Click "Yes" to reboot the PC.
Company confidential NSB-9 CCS Technical Documentation First Time Installation of Phoenix After Dongle driver installation / update (if needed) installation continues from this step. Click "Next" in Welcome dialog to continue. Choose the destination folder, it is recommended to use the default folder C:\ProgramFiles\Nokia\Phoenix. Choose “Next” to continue. You may choose another location by selecting “Browse” (not recommended) Setup copies the components, please wait.
NSB-9 Company confidential CCS Technical Documentation Progress of the setup is shown. Please wait… If restarting of your computer is needed the Install Shield Wizard will tell you about it. Select "Yes..." to reboot the PC immediatelly and "No..." to reboot the PC manually. Note that Phoenix doesn't work, if components are not registered. Click "Finish" to continue. After the reboot components are registered and Phoenix is ready for use. Page 10 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation If reboot is not needed components are registered after copying them. If restarting of your computer is not needed, Click "Finish" to exit the setup. Phoenix is now ready for use.
NSB-9 Company confidential CCS Technical Documentation Update Installation of Phoenix If you already have the Phoenix Service SW installed on your computer, sooner or later there will be need to update it when new versions are released. Please note that very often the Phoenix Service SW and the Phone Specific Data Package for Phoenix come in pairs, meaning that certain version of Phoenix can only be used with certain version of Data Package. Always use the latest available versions of both.
Company confidential NSB-9 CCS Technical Documentation How to Uninstall Phoenix Uninstallation can be done manually from Windows Control Panel - Add / Remove Programs. Choose “Phoenix Service Software” and click "Add/Remove". Choose “OK” to uninstall Progress of the uninstallation is shown. Issue 1 04/03 Copyright Nokia. All rights reserved.
NSB-9 Company confidential CCS Technical Documentation You may have to reboot the PC after uninstallation. If restarting is not needed, the following dialog will appear: Note! If you have different product packages installed, components are uninstalled only if they are not included in other product packages. Page 14 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation Data Package for Phoenix (Product Specific) Before installation Product Data Package contains all product specific data to make the Phoenix Service Software and tools usable with a certain phone model. It also includes the latest version of flash update package for FLS-4* and FPS-8* • Check that the Dongle is attached to the parallel port of your computer. • Install Phoenix Service SW • Download the installation package (e.g. NSB-9_dp_1.00.
NSB-9 Company confidential CCS Technical Documentation Installation of Phoenix Data Package (Product Specific) Run the NSB-9_dp_v_1.00.exe to start installation. When you choose “Next” the files needed for installation will be extracted. Please wait… Choose “Next” to continue. From this view you can see the contents of the Data Package. Read the text carefully. Page 16 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation There should be information about the Phoenix version needed with this data package. Choose “Next”. Confirm location and choose “Next” to continue. Install Shield checks where the Phoenix application is installed and the directory is shown. Choose “Next” to continue. Phone model specific files will be installed... please wait. Issue 1 04/03 Copyright Nokia. All rights reserved.
NSB-9 Company confidential CCS Technical Documentation Choose “Finish” to complete installation. You now have all phone model specific files installed in your Phoenix Service SW. Page 18 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation How to Uninstall Data Package Uninstallation can also be done manually from Windows Control Panel / Add / Remove Programs/ “NSB-9 Phone Data Package”. If you try to install the same version of Phoenix Data Package that you already have, you are asked if you want to uninstall the version you have on your PC. Answer “OK” to uninstall, “Cancel” if you don’t want to uninstall. Older versions of data packages do not need to be uninstalled.
NSB-9 Company confidential CCS Technical Documentation How to Manage Connections Start Phoenix Service SW and Login. Choose “Manage Connections” From “File” – Menu Existing connections can be selected, edited, deleted and new ones created by using this dialog. A connection can be created either manually or by using a Connection Wizard. To add new connection, choose “Add” and select if you want to create it manually or by using the Wizard. Choose “Next” to continue. Page 20 Copyright Nokia.
Company confidential NSB-9 CCS Technical Documentation In the next dialogs you will be asked to select some settings for the connection Manual Settings A) For FLS-4S POS Flash Device choose following connection settings Media: FBUS COM Port: Virtual COM Port used by FLS-4 Please check this always! (To check please go to Windows / Control Panel / FLS Virtual Port / Configuration) B) For FPS-8 Flash Prommer choose following connection settings: Media: FPS-8 Port Num: COM Port where FPS-8 is connected COMBO
NSB-9 Company confidential CCS Technical Documentation Activate the connection you want to use by clicking it and use up/down arrows to move it on top of the list. Choose “Apply”. The connection is now selected and can be used after closing the “Manage Connections” window. Selected connection will be shown on the right hand bottom corner of the screen. To use the selected connection, connect the phone to Phoenix with correct service tools, make sure that it is switched on and select “Scan Product”.
Company confidential NSB-9 CCS Technical Documentation How to Update Flash Support Files for FPS-8* and FLS-4* Before Installation • Install Phoenix Service SW and Phoenix data package. • Install the phone model Specific Datapackage for Phoenix • The flash support files are delivered in the same installation package with Phoenix data package. • Normally it is enough to install the data package only before updating the FPS-8.
NSB-9 Company confidential CCS Technical Documentation If you try to downgrade the existing version to older ones, the setup will be aborted. If you really want to downgrade, uninstall newer files manually from Control Panel and then rerun the installation again. If an older version exists on your PC and it needs to be updated, choose “Next” to continue installation It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia\Phoenix. Page 24 Copyright Nokia.
Company confidential NSB-9 CCS Technical Documentation Choose “Next” to continue. You may choose another location by selecting “Browse” (not recommended). Installation continues… Choose “Finish” to complete procedure. • Issue 1 04/03 FLS-4 can be used right after Flash Update Package is installed. Copyright Nokia. All rights reserved..
NSB-9 Company confidential CCS Technical Documentation • Page 26 FPS-8* must be updated by using Phoenix! Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation How to Update The FPS-8* Flash Prommer SW Start Phoenix Service Software Select”FPS-8 / FPS-8C maintenance” from”Flashing” menu. When new FPS-8 flash update package is installed to computer you will be asked to update the files to your FPS-8 Prommer. Select”Yes” to update files.. 0 02 Update procedure takes a couple of minutes. Issue 1 04/03 Copyright Nokia. All rights reserved..
NSB-9 Company confidential CCS Technical Documentation FPS-8 sw can also be updated by pressing”Update” button and selecting appropriate fps8upd.ini file under C:\Program Files\Nokia\Phoenix\Flash - directory All files can be loaded separately to FPS-8. To do this, just press right mouse button in Flash box files” window and select file type to be loaded. More information and help can be found from the “Help” dialog. Page 28 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation FPS-8 Activation and Deactivation • Before the FPS-8 can be successfully used for phone programming, it must be first activated. • If there is a need to send FPS-8 box to somewhere e.g. for repair, box must be first deactivated. Activation Before FPS-8 can be successfully used for phone programming, it must be first activated. Fill in first “FPS-8 activation request” sheet, in the FPS-8 sales package and follow the instructions in the sheet.
NSB-9 Company confidential CCS Technical Documentation The activation file you saved to C:\ProgramFiles\Nokia\Phoenix\BoxActivation - directory will be shown (e.g. 00000.in), check that it is correct. Box will be activated when you choose “Open” Turn FPS-8 power off and on to complete activation Page 30 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation Deactivation Start Phoenix Service Software. Select ”FPS-8 / FPS-8C maintenance” from ”Flashing” menu Select “Deactivate” from the “FPS8/8C Maintenance” – UI. Confirm Deactivation by choosing “Yes”, Box will be deactivated. Turn FPS-8 power off and on to complete deactivation Issue 1 04/03 Copyright Nokia. All rights reserved..
NSB-9 Company confidential CCS Technical Documentation JBV-1 Docking Station SW The JBV-1 Docking Station is a common tool for all DCT-4 generation products. In order to make the JBV-1 usable with different phone models, a phone specific Docking Station Adapter is used for different service functions. The JBV-1 Docking Station contains Software (Firmware) which can be updated.
Company confidential NSB-9 CCS Technical Documentation Installing SW Needed for the JBV-1 SW Update Note: DO NOT CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER YET! Run Jbv1_update.zip file and start SW Installation by double clicking Setup.exe. Files needed for JBV-1 Package setup Program will be extracted. Installation begins, please read the information shown and Choose “Next” to continue.
NSB-9 Company confidential CCS Technical Documentation “Next” to continue. Select “Full” Installation and choose “Next” to continue Program Folder will be created. Choose “Next” to continue, Software files will be Page 34 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation installed. After successful installation, choose “Finish” to complete. NOW YOU CAN CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER! Connect power to JBV-1 (11-16V DC) from external power supply, then connect USB Issue 1 04/03 Copyright Nokia. All rights reserved..
NSB-9 Company confidential CCS Technical Documentation Cable between JBV-1 USB connector and PC. Windows will detect connected USB cable and detect drivers for new HW. Follow the instructions and allow Windows to search and install the best drivers available. After this procedure the actual JBV-1 SW update can begin. Page 36 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation Updating the JBV-1 Docking Station Software Go to folder C:\Program Files\Nokia\ JBV-1 SW Package\ FIRMWARE UPDATE and start JBV-1 Update SW by double clicking fwup.exe. JBV-1 Firmware update starts and shows current status of the JBV-1 connected. If firmware version read from your JBV-1 is not the latest one available, it needs to be updated by choosing “Update Firmware”. Choose file JBV1v11.
NSB-9 Company confidential CCS Technical Documentation software of your JBV-1 docking station and it is ready for use. Page 38 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation [This page left intentionally blank] Issue 1 04/03 Copyright Nokia. All rights reserved..
NSB-9 Company confidential CCS Technical Documentation Page 40 Copyright Nokia. All rights reserved.
NSB-9 CCS Technical Documentation Quick Guide for Tuning With Phoenix General remarks If baseband tunings are needed, they should be completed before the RF tunings. Avoid unnecessary tuning – factory-tuning values are always the most accurate ones. Screen shots described in this document may change as the service software is developed. Kindly refer to the Phoenix help files, the phone model specific service manual and bulletins for help. Issue 1 04/03 Copyright Nokia. All rights reserved..
NSB-9 CCS Technical Documentation RF Tuning and Calibration Instructions for Iris HDB58 Introduction This document describes the methods of RF tunings and calibrations for Iris NSB-9 transceiver. RF tunings are made using automatic setup in which Phoenix software controls the phone via FBUS and the measurement equipment via GPIB bus. Autotune feature is designed to align the product’s RF part easier and faster. By this autotune component the product is tuned automatically. Manual tuning is not available.
NSB-9 CCS Technical Documentation Figure 1: RF tuning concept Figure 2: Setup environment Issue 1 04/03 Copyright Nokia. All rights reserved..
NSB-9 CCS Technical Documentation Autotuning The Autotune component can be found under Tuning menu: Figure 3: Autotune menu in Phoenix When tuning, one only needs to click the Tune button to start automatic tuning procedure. Figure 4: Autotune menu - RX/TX menu The tuning results are shown in RX and TX windows. Page 42 Copyright Nokia. All rights reserved.
NSB-9 CCS Technical Documentation Set Loss Figure 5: Set Loss menu This is the component for saving RF-losses (of cables and jigs) to file. These loss values are needed when you tune the phone with Phoenix (using Auto-Tune component). When you measure the losses you have to be very careful, because these values affect directly how well the phone is tuned. Note! Components are protected by PKD-1CS, PKD-1NS, PKD-1 and PKD-1P dongles using standard TSS protection procedure.
NSB-9 CCS Technical Documentation RX tunings Channel Select Filter Calibration Description Rx Channel select filter is tuned only in one band. The Hagar RF IC contains tunable filters for the I and Q channels. The calibration of these filters is carried out with a calibration circuit integrated in the IC. By writing different control words to the Calibration Control Register in Hagar, internal switches will connect various RC combinations between the TXC input line and the RXQ output line.
NSB-9 CCS Technical Documentation *) Tuning may return values between -6...37 but values between 0...31 are saved to phone permanent memory. Values -6...0 are round up to 0 and values 31...37 are round down to 31. RX Calibration Description Calibrates 26 MHz voltage controlled reference oscillator VCTCXO at the beginning of GSM850 receiver gain (RSSI) tuning. AFC control voltage for VCTCXO is produced using 11-bits DA-converter inside UEM RF IC.
NSB-9 CCS Technical Documentation and Q) has always zero value.
NSB-9 CCS Technical Documentation ch 190 / 661 +0.5 ... +1.0 -5 5 +0.4 ... +0.9 -5 5 ch 217 / 736 +0.1 ... +0.7 -5 5 -0.3 ... +0.3 -5 5 ch 241 / 794 -0.7 ... -0.1 -5 5 -0.9 ... 0.0 -5 5 ch 251 / 810 -1.2 ... -0.3 -5 5 -1.0... 0.0 -5 5 ch 261 / 835 -1.8 ... -0.8 -10 5 -2.1 ... -0.7 -10 5 Issue 1 04/03 Copyright Nokia. All rights reserved..
NSB-9 CCS Technical Documentation TX tunings Tx Power Level Tuning Calibrates GSM850 and GSM1900 TX power at middle channel. Power control loop keeps TX power same in all channels. Tuning is done at 4 power levels - other values can be linearized using these points. GSM850 GSM1900 Power Level Target value Tuning target Testing limits *) Power Level Target value Tuning target Testing limits *) 5 32.5 +/- 0.1 +0.2 / -0.5 0 29.5 +/- 0.1 +0.2 / -0.5 6 31 +/- 0.5 +/- 1 1 28 +/- 0.
NSB-9 CCS Technical Documentation TX IQ Tuning Calibrates GSM850 and GSM1900 TX I/Q signal DC-offset, amplitude and phase difference at middle channel. Tuning is done by sending '1'-bits to the modulator. Best modulator balance is achieved when spikes at carrier frequency f0 and f0+67.71 kHz reach minimum value.
NSB-9 CCS Technical Documentation Service Tool Concept For Baseband Tuning Operations EM calibrations should be carried out in JBV-1 Docking Station equipped with MJF-32 Docking Station Adapter Power to JBV-1 should be supplied from an external DC power suply, not FPS-8 prommer JBV-1 input voltages: Maximum + 16 VDC Nominal input for BB tunings is +12 V DC. Page 50 Copyright Nokia. All rights reserved.
NSB-9 CCS Technical Documentation Service Concept for NSB-9 Baseband tunings Item: Service accessory: Type: Product code: 1 Docking station JBV-1 0770298 2 Docking station adapter MJF-32 0770528 3 DC-DC cable SCB-3 0730114 4 RF antenna cable XRF-1 0730085 5 DC power cable PCS-1 0730012 6 Service MBUS cable DAU-9S 0730108 7 Software protection key PKD-1 0750018 8 Phoenix Service SW 8409031 Phoenix Service SW CD-ROM NSB-9 Flash SW data NSB-9 Flash SW data Issue 1 04/03
NSB-9 CCS Technical Documentation Baseband Tuning operations Energy Management Tuning External power supply needed. EM Calibration is used for calibrating Battery and Charger settings of the phone. Preparation for EM Calibration: - Connect DC Cable SCB-3 between JBV-1 and charger socket of Phone for Charger calibration. - Connect 12…15 V from Power Supply to JBV-1. - NOTE! Check that connection is F-BUS (does not work with M-BUS!). Select Maintenance => Tuning => Energy Management Calibration.
NSB-9 CCS Technical Documentation Select “Calibrate” to run the selected calibrations. Limits for Energy Management Calibration: Parameter Min.
NSB-9 CCS Technical Documentation LCD Contrast Tuning Extra equipment not needed. This function is used to calibrate the LCD Contrast (brightness). Must be done when LCD module is changed and there is considerable difference in the contrast. Select Maintenance => Testing => Display Tune Move the Contrast factory offset slider to reach good LCD contrast. Both sliders are relative. The Default button resets the bottom Contrast factory offset slider to default value 41.
Company confidential NSB-9 CCS Technical Documentation Flashing Setup Instructions POS (Point of Sale) Flash Concept Figure 1: POS flash Item Type Description Code 1 FLA-29 Point Of sales flash loading adapter 0775306 2 XCS-1 Service cable 0730218 3 ACF-8 AC Charger 0680032 4 FLS-4S POS flash dongle, for Americas area 0080543 5 Phoenix Service SW Phoenix Service SW Issue 1 04/03 8409031 CD-ROM Copyright Nokia. All rights reserved..
NSB-9 Company confidential CCS Technical Documentation Item Type Description NSB-9 Flash SW data NSB-9 Flash SW data Page 72 Code 8415951 CD-ROM Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation Flash Concept with flashing adapter Item Type Description Code 1 FLA-29 Point of sales flash loading adapter 0775306 2 FLC-2 Power cable 0730185 3 XCS-4 Modular cable 0730178 4 FPS-8 Flash prommer box 0080321 Centronics (printer) cable, incl. in FPS8 slaes package 0730029 5 6 AXS-4 RS-232 (D9-D9) cable, incl.
NSB-9 Company confidential CCS Technical Documentation Item Type Description NSB-9 Flash SW data 9 Page 74 Code 8415951 NSB-9 Flash SW data CD-ROM 0775344 ACF-8 AC-charger, incl. in FPS-8 sales package 0680032 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation Module Jig Concept Figure 2: Module jig concept Item Type Description Code 1 MJS-48 Module jig 0770392 2 PCS-1 DC power cable 0730012 3 XRF-1 RF antenna cable 0730085 4 DAU-9S Service MBUS cable 0730108 5 PKD-1 Software protection key (Dongle) 0750018 6 Phoenix Service SW Phoenix Service SW 8409031 CD-ROM NSB-9 Flash SW data NSB-9 Flash SW data Issue 1 04/03 0775311 8415951 CD-ROM Copyright Nokia.
NSB-9 Company confidential CCS Technical Documentation JBV-1 Flash Concept Figure 3: JBV-1 Flash concept Item Type Description Code 1 JBV-1 Docking station 0770298 2 MJF-32 Docking station adapter 0770528 3 PCS-1 DC power cable 0730012 4 XCS-4 Modular cable 0730178 5 FPS-8 Flash prommer box 0080321 Centronics (printer) cable, incl. in FPS-8 sales package 0730029 RS232 (D9 – D9) cable, incl. in FPS-8 sales pack 0730090 6 7 Page 76 AXS-4 Copyright Nokia. All rights reserved.
Company confidential NSB-9 CCS Technical Documentation Item Type Description Code 8 PKD-1 Software protection key (Dongle) 0750018 9 Phoenix Service SW Phoenix Service SW 8409031 CD-ROM NSB-9 Flash SW data 10 Issue 1 04/03 0775311 8415951 NSB-9 Flash SW data CD-ROM 0775344 ACF-8 AC Charger, incl. in FPS-8 sales pack 0680032 Copyright Nokia. All rights reserved..
NSB-9 Company confidential CCS Technical Documentation Service Concept Figure 4: Service Concept Item: Service accessory: Type: Product code: 1 Docking station JBV-1 0770298 2 Docking station adapter MJF-32 0770528 3 DC-DC cable SCB-3 0730114 4 RF antenna cable XRF-1 0730085 5 DC power cable PCS-1 0730012 6 Service MBUS cable DAU-9S 0730108 7 Software protection key PKD-1 0750018 8 Phoenix Service SW Phoenix Service SW 8409031 CD-ROM NSB-9 Flash SW data NSB-9 Flash SW d
Company confidential NSB-9 CCS Technical Documentation Parallel Flash concept Figure 5: Parallel flash concept Item Type Description Code 1 JBV-1 Docking station 0770298 2 MJF-32 Docking station adapter 0770528 3 XCS-4 Modular cable 0730178 4 PCS-1 DC power cable 0730012 5 FPS-8C Parallel flash prommer 0080396 6 AXS-4 RS232 (D9 – D9) cable, incl. in FPS-8C sales package 0730090 7 Printer cable Centronics (printer) cable, Incl.
NSB-9 Company confidential CCS Technical Documentation Item Type Description NSB-9 Flash SW data NSB-9 Flash SW data Page 80 Code 8415951 CD-ROM Copyright Nokia. All rights reserved.
