CCS Technical Documentation NSB-9 Series Transceivers Service tools Issue 1 04/03 Nokia Corporation
NSB-9 Service tools CCS Technical Documentation Table of Contents Page No JVB-1 Docking Station and MJF-32 Adapter................................................................ 3 MJS-48 Module Test Jig ................................................................................................ 5 MJS-70 Soldering Jig..................................................................................................... 6 SS-4 Domesheet Assembly Jig .......................................................
NSB-9 Service tools CCS Technical Documentation JVB-1 Docking Station and MJF-32 Adapter The JVB-1 Docking Station has been designed for calibration and soft ware update use. The MJF-32 Docking Station Adapter makes signal connections to the phone. JVB-1 and MJF-32 are used as one unit.
NSB-9 Service tools CCS Technical Documentation View of JBV-1 and MJF-32 together Page 4 Nokia Corporation Issue 1 04/03
NSB-9 Service tools CCS Technical Documentation MJS-48 Module Test Jig Module Test Jig MJS-48 is designed for regional Central Services for RM9 module testing. It can be used for flashing and RF-, battery-, system-, radio- and SIM reader testing. Product Code MJS-48 Module Test Jig: 0770392 View of MJS-48 Note: For RF-tests and tunings, it is possible to bypass the regulator (with jumper). The nominal supply voltage for MJS-48 is +4.2 V (when the jumper is in bypass position).
NSB-9 Service tools CCS Technical Documentation MJS-70 Soldering Jig MJS-70 Soldering Jig is used for soldering and as a rework jig for RM9 module. PWB fits into the jig either side up.
NSB-9 Service tools CCS Technical Documentation SS-4 Domesheet Assembly Jig SS-4 Domesheet is a jig for domesheet assembly. Note: Insert PWB bottom connector end first.
NSB-9 Service tools CCS Technical Documentation FPS-8 Flash Prommer (Sales Pack) The Flash Prommer FPS-8 is used with e.g. MJF-32 and JVB-1. Power is supplied to FPS-8 from the Universal Power Supply.
NSB-9 Service tools CCS Technical Documentation FPS-8C Parallel Flash Prommer (Sales Pack) The Parallel Flash Prommer FPS-8C is used with MJF-32 and JVB-1. Flash programming can be done to maximum of 8 phones parallel. FPS-8C consists of eight SF11C programming cards. SF11C card is functionally identical to FPS-8.
NSB-9 Service tools CCS Technical Documentation ACF-8 Universal Power Supply ACF-8 Universal Power Supply is used to power FPS-8. ACF-8 has 6 V DC and 2.1 A output.
NSB-9 Service tools CCS Technical Documentation FLA-29 POS (Point Of Sale) Flash Adapter FLA-29 POS Flash Adapter is used in place of the phone's normal battery during service, to supply a controlled operating voltage.
NSB-9 Service tools CCS Technical Documentation FLC-2 DC Cable The FLC-2 is used to supply a controlled operating voltage to the FLA-29 POS adapter when used with the FPS-8 flash prommer.
NSB-9 Service tools CCS Technical Documentation AXS-4 Service Cable The AXS-4 D9-D9 Service Cable is used to connect two 9 pin D connectors e.g. between PC and FPS-8. Cable length is 2 meters.
NSB-9 Service tools CCS Technical Documentation XCS-1 Service Cable The XCS-1 Service Cable is used to connect FLS-4 to FLA-29.
NSB-9 Service tools CCS Technical Documentation SW Security Device PKD-1 SW security device (dongle) is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC. Without the dongle present it is not possible to use the service software. Printer or any such device can be connected to the PC through the dongle if needed.
NSB-9 Service tools CCS Technical Documentation FLS-4S POS (Point Of Sale) Flash Device (Sales Pack) FLS-4S is a dongle and flash device incorporated into one package, developed specifically for POS use.
NSB-9 Service tools CCS Technical Documentation PCS-1 Power Cable The PCS-1 Power Cable (DC) is used to connect e.g. JVB-1 to FPS-8 or MJS-48 to an external power supply.
NSB-9 Service tools CCS Technical Documentation XRF-1 RF Cable RF cable XRF-1 is used to connect e.g. Module Jig MJS-48 to RF measurement equipment.
NSB-9 Service tools CCS Technical Documentation DAU-9S MBUS Cable The MBUS Cable DAU-9S has a modular connector, and is used with between PC's serial port and e.g. Module Jig MJS-48.
NSB-9 Service tools CCS Technical Documentation SCB-3 DC Cable The DC Cable SCB-3 is used to connect e.g. JVB-1 to the phone.
NSB-9 Service tools CCS Technical Documentation XCS-4 Modular Cable XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing and service purposes.
NSB-9 Service tools CCS Technical Documentation Printer Cable This cable is used to connect the PC to FPS-8.
NSB-9 Service tools CCS Technical Documentation [This page left intentionally blank.
NSB-9 Service tools Page 24 CCS Technical Documentation Nokia Corporation Issue 1 04/03
