CCS Technical Documentation RH-26 Series Transceivers 6 - Disassembly and Assembly Instructions Issue 1 02/04 ©Nokia Corporation.
RH-26 Company confidential 6 - Disassembly and Assembly Instructions CCS Technical Documentation [This page intentionally blank] Page 2 ©Nokia Corporation.
CCS Technical Documentation Company confidential RH-26 6 - Disassembly and Assembly Instructions Table of Contents Page No Disassembling the Phone ............................................................................................... 3 Changing the Dome Sheet.............................................................................................. 9 Issue 1 02/04 ©Nokia Corporation.
RH-26 Company confidential 6 - Disassembly and Assembly Instructions CCS Technical Documentation [This page intentionally blank] Page 4 ©Nokia Corporation.
Company confidential RH-26 6 - Disassembly and Assembly Instructions CCS Technical Documentation Disassembling the Phone (1) (2) Check the condition of the window. Protect the window with a film. To remove the battery cover (2), pull the locking latch (1). (3) (4) Remove battery from the battery cover. To remove the A-cover, first release the clip by using SRT-6. (5) (6) Then open the flip upright. Open the other side clips with SRT-6. Start with the clip as shown in the picture above.
RH-26 Company confidential 6 - Disassembly and Assembly Instructions CCS Technical Documentation (9) (10) Open the clip on the other side. Open the flip completely. (11) (12) First, lift the topside of the A-cover then move the Acover forward. To remove the window, press down the function keys as shown in the picture above. (13) (14) Remove the joystick button. The bottom side of the keymat is glued to the keydome, therefore move up the keymat with SRT-6 carefully. Mind the underneath LEDs.
CCS Technical Documentation Company confidential RH-26 6 - Disassembly and Assembly Instructions (17) (18) Carefully remove the coax connector with tweezers, while taking care not to cant the connector. The modules can now be separated. (19) (20) Protect the LCD with a film. Carefully place SRT-6 between the qwerty frame and flip. (21) (22) Move SRT-6 on along the edge. To release the leaving snaps, use fingers to grip the qwerty frame. (23) (24) The qwerty frame is loose.
RH-26 Company confidential 6 - Disassembly and Assembly Instructions CCS Technical Documentation (25) (26) Unlock the two snaps of T9 keymat with SRT-6. You can now remove the T9 keymat. (27) (28) Carefully remove the coax connector with angled tweezers, while taking care not to cant the connector. Push out the flip electric module from the backside to the front. (29) (30) You can use a DC plug to remove the DC-jack.
Company confidential RH-26 6 - Disassembly and Assembly Instructions CCS Technical Documentation (33) (34) Remove the SIM cover. Open display clips on both sides. (35) (36) To unplug the display connector, pull the modules apart very carefully. The earpiece is attached with a double-sided adhesive foam tape. Always use a new tape when mounting the earpiece anew. (37) (38) When placing the module upside down on the desk, take care not to damage the joystick. Use the soldering jig when repairing.
RH-26 Company confidential 6 - Disassembly and Assembly Instructions CCS Technical Documentation (39) (40) The camera module is attached with four snaps into its guidance. To unlock the snaps on both sides, place SRT-10 as shown in the picture. Note the releasing order. Do not touch contacts or the camera lens. Always use SRT-10 for assembly and disassembly. Page 10 ©Nokia Corporation.
Company confidential RH-26 6 - Disassembly and Assembly Instructions CCS Technical Documentation Changing the Dome Sheet (1) (2) To loosen the corner of the keydome, use SRT-6. Be careful not to damage the LEDs. The B-cover or soldering jig can be used to fix the power board. To avoid remains of glue, tear off the keydome in diagonal direction. Check pads for cleanness. (3) (4) Place a new keydome on to the assembly jig. Note the guiding pins. Remove the protection foil.
RH-26 Company confidential 6 - Disassembly and Assembly Instructions CCS Technical Documentation (7) (8) Carefully press the power board onto the keydome. Check that the keydome is properly mounted to the power board. Page 12 ©Nokia Corporation.
