CCS Technical Documentation NSM-9DX Series Transceivers Service Tools Issue 1 10/02 Nokia Corporation
NSM-9DX Service Tools CCSTechnical Documentation Table of Contents Page No JBV-1 Docking Station and MJF-6 Adapter ...............................................................4 Product Code ............................................................................................................. 4 MJS-46 Module Jig ......................................................................................................6 Product Code .....................................................................
NSM-9DX Service Tools CCSTechnical Documentation List of Figures Page No Fig 1 View of JBV-1 and MJF-6 together ...........................................................................5 Fig 2 View of MJS-46 .........................................................................................................6 Fig 3 View of MJS-47 .........................................................................................................7 Fig 4 View of FPS-8 .............................................
NSM-9DX Service Tools CCSTechnical Documentation JBV-1 Docking Station and MJF-6 Adapter The JBV-1 Docking Station has been designed for calibration and software update use. The MJF-6 Docking Station Adapter makes signal connections to the phone. JBV-1 and MJF-6 are used as one unit.
NSM-9DX Service Tools CCSTechnical Documentation Figure 1: View of JBV-1 and MJF-6 together CPL-6 RF-Coupler: 0775308 CPL-6 is used with JBV-1 and MJF-6 for making RF coupler connection from the phone to measurement equipment. CPL-9 RF-Coupler: 0770529 CPL-9 is used with JBV-1 and MJF-6 for making RF coupler connection from the phone to the measurement equipment.
NSM-9DX Service Tools CCSTechnical Documentation MJS-46 Module Jig The MJS-46 Module Jig is used for testing of UI/system/RF-module*. Product Code MJS-46 Module Jig: 0770316 Figure 2: View of MJS-46 *Note: The nominal supply voltage for MJS-46 is +8.0 V. The supply voltage must not exceed +12.0 V (min. 5V). (MJS-46 has overvoltage protection). For flashing with FPS-8, it is possible to bypass the regulator with a jumper. Then the supply voltage must not exceed 5.2 V.
NSM-9DX Service Tools CCSTechnical Documentation MJS-47 Soldering Jig The Soldering Jig MJS-47 is used for soldering and as a rework jig for system module.
NSM-9DX Service Tools CCSTechnical Documentation FPS-8 Flash Prommer (Sales Pack) The Flash Prommer FPS-8 is used with e.g. FLA-18 and JBV-1. Power is supplied to FPS-8 from the Universal Power Supply.
NSM-9DX Service Tools CCSTechnical Documentation FPS-8C Parallel Flash Prommer (Sales Pack) The Parallel Flash Prommer FPS-8C is used with MJF-6 and JBV-1. Flash programming can be done to maximum of 8 phones parallel. FPS-8C consists of eight SF11C programming cards. SF11C card is functionally identical to FPS-8.
NSM-9DX Service Tools CCSTechnical Documentation ACF-8 Universal Power Supply ACF-8 Universal Power Supply is used to power FPS-8. ACF-8 has 6 V DC and 2.1 A output.
NSM-9DX Service Tools CCSTechnical Documentation FLA-18 POS (Point Of Sale) Flash Loading Adapter The POS Flash Loading Adapter FLA-18 is used in place of the phone's normal battery during service, to supply a controlled operating voltage.
NSM-9DX Service Tools CCSTechnical Documentation FLC-2 DC Cable The FLC-2 is used to supply a controlled operating voltage.
NSM-9DX Service Tools CCSTechnical Documentation AXS-4 Service Cable The AXS-4 D9-D9 Service Cable is used to connect two 9 pin D connectors e.g. between PC and FPS-8. Cable length is 2 meters.
NSM-9DX Service Tools CCSTechnical Documentation XCS-1 Service Cable The XCS-1 Service Cable is used to connect FLS-4 to FLA-18.
NSM-9DX Service Tools CCSTechnical Documentation SW Security Device PKD-1 SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC. Without the dongle present it is not possible to use the service software. Printer or any such device can be connected to the PC through the dongle if needed.
NSM-9DX Service Tools CCSTechnical Documentation FLS-4 POS (Point Of Sale) Flash Device (Sales Pack) FLS-4 is a dongle and flash device incorporated into one package, developed specifically for POS use.
NSM-9DX Service Tools CCSTechnical Documentation PCS-1 Power Cable The PCS-1 Power Cable (DC) is used to connect, for example, JBV-1 to FPS-8.
NSM-9DX Service Tools CCSTechnical Documentation XRF-1 RF Cable RF cable XRF-1 is used to connect, for example, the Module Jig MJS-46 to the RF measurement equipment.
NSM-9DX Service Tools CCSTechnical Documentation DAU-9S MBUS Cable The MBUS Cable DAU-9S has a modular connector, and is used with between PC's serial port and, for example, the Module Jig MJS-46.
NSM-9DX Service Tools CCSTechnical Documentation SCB-3 DC Cable The DC Cable SCB-3 is used to connect, for example, the JBV-1 to the phone.
NSM-9DX Service Tools CCSTechnical Documentation XCS-4 Modular Cable XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing and service purposes.
NSM-9DX Service Tools CCSTechnical Documentation Printer Cable This cable is used to connect the PC to FPS-8.
