CCS Technical Documentation RH-25 Series Transceivers Service Tools Issue 1 10/2003 Confidential © 2003 Nokia Corporation
RH-25 Service Tools CCS Technical Documentation Contents Page No Service Tools.................................................................................................................. 3 6560 .............................................................................................................................3 Flashing and Testing Setups .......................................................................................... 8 FPS-8 Flash Prommer for Heavy Flash .........................
RH-25 Service Tools CCS Technical Documentation Service Tools 6560 Photo Issue 1 10/2003 Confidential Code Service Tool Code Description MJ-16 Module Jig 0770575 This jig allows phone PWB-level service and troubleshooting. Electric currents should be protected against over-voltage and over-current. FLS-4S POS Flash Adapter 0080543 The Point of Sale (POS) flash is a lowcost software upgrade tool. This requires the XCS-1 cable and ACP-8U for operation.
RH-25 Service Tools Photo CCS Technical Documentation Code Service Tool Code Description JBV-1 Docking Station 0770298 The Docking Station and the Docking Station Adapter (DA-15) are needed for Mbus, Fbus, RF, and audio connections. This setup allows connection between flash prommers. When the audio box is connected, it has to be connected to the phone’s audio connector. DA-15 Docking Station Adapter 0770624 The Docking Station can be powered by FPS-8 or external power supply.
RH-25 Service Tools CCS Technical Documentation Photo Issue 1 10/2003 Confidential Code Service Tool Code Description SF-15 Flash Adapter 0770625 SF-15 allows a continuous maximum power supply for the phone from an external power supply, the ACP-8. NOTE: SEE USER INSTRUCTIONS FOR SF-15 ON PAGE 11. Note: SF-15 is not to be used for handset testing; it is only designed for flashing.
RH-25 Service Tools Photo Page 6 CCS Technical Documentation Code Service Tool Code Description DAU-9S Mbus Cable 0730108 The Mbus Cable has a modular connector and is used with the service audio box JBA-4 or a modular T-adapter. PCS-1 Power Cable 0730012 The Power Cable PCS-1 is used to connect the service tools (JBV-1, MJF-23) to an external power supply. XRF-1 RF Cable 0730085 The XRF-1 cable connects a service tool and RF measurement equipment.
RH-25 Service Tools CCS Technical Documentation Photo Issue 1 10/2003 Confidential Code Service Tool Code Description PKD-1 SW Security Device 0750018 SW security device PKD-1 is hardware device that, when connected to the parallel (LPT) port of the PC, enables the use of the service software. Without the dongle present, it is not possible to use the service software. Printers or other peripheral devices can be connected to the PC through the dongle, if needed.
RH-25 Service Tools CCS Technical Documentation Flashing and Testing Setups FPS-8 Flash Prommer for Heavy Flash The FPS-8 flash prommer is used for heavy flashing. The sales pack product code is 0080321. FPS-8C Flash Prommer for Heavy Parallel Flash The FPS-8C flash prommer is used for heavy parallel flashing. The sales pack product code is 0080396.
CCS Technical Documentation RH-25 Service Tools User Instructions DA-15 / SA-16 Follow these instructions to avoid damage to the adapter or the phone. Note: Using the adapter in any way other than described here may harm important pins and connectors of the adapter. It cannot be used like the FLA-13 for 3520/3560 products. 1 Lock bottom of phone onto the jig. 2 In an arching motion, push phone downward. 3 Push phone down until locks engage.
RH-25 Service Tools 4 CCS Technical Documentation Push the probe up from the bottom (photo at left below) and then engage the locking mechanism (right). To remove adapter, follow the inverse order of the installation in Steps 1 through 4.
CCS Technical Documentation RH-25 Service Tools SF-15 Follow these instructions to avoid causing any damage to the adapter or the phone. Note: Using the adapter in any other way may harm the important pins and connectors of the adapter. It cannot be used like the MJF-2 for 3520/3560 products. 1 Lock bottom of the SF-15 onto the phone. 2 In an arching motion, push the phone and the SF-15 together until the locks engage.
RH-25 Service Tools 3 Page 12 CCS Technical Documentation To remove, press the tabs on BOTH sides to release.
