c1caus.
c1caus.frm Page 2 Thursday, December 19, 1996 12:46 PM NOKIA and the Arrows logo are registered trademarks of Nokia Corporation, Finland. © 1996 Nokia Mobile Phones. All rights reserved. Nokia Mobile Phones operates a policy of continuous improvement, therefore, we reserve the right to make changes and improvements to any of the products described in this guide without prior notice.
c1caus.frm Page 3 Thursday, December 19, 1996 12:46 PM Contents IMPORTANT SAFETY INFORMATION ................... 5 KEYS AND DISPLAY INDICATORS......................... 9 List of Keys ..................................................................................... 9 Display Indicators...................................................................... 10 Display Editing ........................................................................... 11 GETTING STARTED ....................................
c1caus.frm Page 4 Thursday, December 19, 1996 12:46 PM USING THE MENU FACILITY ............................... 30 Menu Method............................................................................. Shortcut Method ....................................................................... List of Menu Functions ............................................................ Descriptions of Menu Functions ........................................... STORE TO MEMORY (MENU 1) ................................
c1caus.frm Page 5 Thursday, December 19, 1996 12:46 PM 1. IMPORTANT SAFETY INFORMATION Traffic Safety • Do not use a hand-held phone while driving a vehicle. If using a hand-held phone, park the vehicle before conversing. • Always secure the phone in its holder; do not place the phone on the passenger seat or where it can break loose in a collision or sudden stop. • The use of an alert device to operate a vehicle's lights or horn on public roads is not permitted.
c1caus.frm Page 6 Thursday, December 19, 1996 12:46 PM • Do not store or carry flammable liquids, gases or explosive ma- terials in the same compartment as a cellular phone or any of its parts or accessories. • Only qualified personnel should install or service the phone in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty which may apply to the unit.
c1caus.frm Page 7 Thursday, December 19, 1996 12:46 PM To make an emergency call: 1 If the phone is not on, switch it on by pressing and holding the PWR key. 2 Press and hold the CLR key for several seconds to ready the phone for calls. 3 Enter the emergency number for your present location (e.g., 911 or another official emergency number). Emergency numbers vary by location. 4 Press the SEND key. If certain features are in use (e.g.
c1caus.frm Page 8 Thursday, December 19, 1996 12:46 PM Using This Guide The cellular phone described in this guide is approved for use in AMPS networks. A number of features included in this guide are called Network Services. They are special services provided by cellular service providers. Before you can take advantage of any of these Network Services, you must subscribe to the service(s) you require from your home service provider. You may then activate and use the functions as described in this guide.
c1caus.frm Page 9 Thursday, December 19, 1996 12:46 PM 2. KEYS AND DISPLAY INDICATORS List of Keys PWR Press and hold the key to switch the phone on and off. ABC Used to switch between alpha and numeric modes. MENU Used to enter the menu facility. Press the MENU key and then scroll through the menu functions by using the arrow key ( ), or press first the MENU key and then a menu shortcut number. (See Shortcut Method on page 30.) OK Used to confirm a setting in the menu facility.
c1caus.frm Page 10 Thursday, December 19, 1996 12:46 PM Display Indicators AB Indicates which network is currently in use: A system only B system only AB both systems Blank home area only ABC Indicates that the phone is in ALPHA mode and letters can be entered or displayed. MENU Indicates that the MENU key has been pressed and you are in the menu facility. Indicates the number of a menu function or phone directory memory location. ON Indicates that the phone is switched on.
c1caus.frm Page 11 Thursday, December 19, 1996 12:46 PM Display Editing The display can be edited using the CLR key. • Press the CLR key once to delete the last digit. • Press the CLR key repeatedly to delete digits one by one. • Press and hold the CLR key to clear the whole display. Clearing the whole display restores the display to the numeric mode. The phone can display up to 16 digits. If you enter more than this (max. 32 digits), the first digits will run-off the display, and you cannot view them.
c1caus.frm Page 12 Thursday, December 19, 1996 12:46 PM 3. GETTING STARTED Installing the Battery To install the Battery: 1 Place the battery onto the rear of 2. the phone (1). 1. 2 Push the battery towards the catch until it clicks into place (2). 3 Make sure the battery is properly installed. To remove the Battery: 1 Switch off the power before removing the battery. 2 Press the locking catch at the top of the battery and slide the battery down and off the phone.
c1caus.frm Page 13 Thursday, December 19, 1996 12:46 PM • Note: A new battery must be fully charged before being used for the first time. • Battery charging times depend on the type of battery and charger used. Battery operation times depend greatly on how you use the batteries, as well as on the coverage of the network and network parameters set by the cellular service provider.
c1caus.frm Page 14 Thursday, December 19, 1996 12:46 PM 4. GENERAL FUNCTIONS Switching On/Off If your phone has an extendable antenna, extend the antenna fully. As with any other radio transmitting device, avoid unnecessary contact with the antenna when the phone is switched on. 1 Press and hold the PWR key for one second to switch on the phone. • The phone will carry out a short self-test briefly displaying its activated phone number.
c1caus.frm Page 15 Thursday, December 19, 1996 12:46 PM Receiving a Call When there is an incoming call, the phone will give a ringing tone and the CALL message will flash on the display. • If you have set the menu function Ringing Volume to SILENT SERVICE, the keypad and display lights will flash, the CALL message will flash on the display and only a short beep tone will be given. You can answer a call any time, even while using the memory or menu functions.
c1caus.frm Page 16 Thursday, December 19, 1996 12:46 PM Last Number Redial The last five phone numbers you called or attempted to call (and associated names if entered) are stored in the phone's memory location 0 (L0-L4). This stack of the five last dialed numbers remains in the phone's memory when the phone is switched off. To redial a last number dialed: 1 If there are any characters on the display, clear the display by pressing and holding the CLR key.
c1caus.frm Page 17 Thursday, December 19, 1996 12:46 PM 9 Key Emergency Dialing If the menu function emergency Key 9 is set to on (EMERG. 9 ON), you can make an emergency call to the emergency number programmed into your phone by pressing and holding the 9 key. • The phone dials the the emergency programmed into the phone displays the message EMERG. CALL TRY . Note: The official emergency numbers vary by location (e.g., 911 or another official emergency number).
c1caus.frm Page 18 Thursday, December 19, 1996 12:46 PM Keyguard The phone's keypad may be locked to prevent unintended keypresses from being made when the phone is, for example, in a pocket or a bag. No security code is required to activate or deactivate this keyguard feature. To activate the keyguard: 1 Press the MENU key and then the ✱ key. You can also activate the keyguard by pressing and holding the END key. This is a convenient way to activate the keyguard when you end a call.
c1caus.frm Page 19 Thursday, December 19, 1996 12:46 PM Calling Card Call Note: This feature may not be operational in all countries. When making a call, the call charges can be directed to a selected calling card company, if the card number is sent to the network during the call setup. Before making an automatic calling card call, you have to activate one of the calling card option from the menu function CALLING CARD.
c1caus.frm Page 20 Thursday, December 19, 1996 12:46 PM 5. USING THE MEMORY Standard Memory Locations Your phone has 40 standard alpha-numeric memory locations. Memory locations 1-20 (short) can hold phone numbers of up to 16 digits and names of up to 16 characters. Memory locations 2140 (long) can hold numbers of up to 32 digits and names of up to 16 characters.
c1caus.frm Page 21 Thursday, December 19, 1996 12:46 PM Notepad Memory Location Your phone has one short term memory location, where a phone number can temporarily be stored, e.g., during a call. This location is automatically cleared when the phone is switched off. To store a number in the notepad memory: 1 Press the MENU key and scroll to the menu function STORE TO MEMORY by using the 1. key and press OK, or press MENU The phone asks you to enter the name to be stored (NAME?).
c1caus.frm Page 22 Thursday, December 19, 1996 12:46 PM Entering Names 1 If in the numeric entry mode, press the ABC key to select the alpha mode. The ABC indicator will appear on the display to indicate that letters can now be entered. 2 Press the key labeled with the letter you want. Press it once to obtain the first letter, twice (before the cursor appears) to obtain the second and so on. If you miss the letter you want, just repress the key until the desired character appears.
c1caus.frm Page 23 Thursday, December 19, 1996 12:46 PM To use the menu method: 1 Press the MENU key and scroll to the menu function STORE TO MEMORY by using the key and press OK, or press MENU 1 as a shortcut access method. The phone asks you to enter the name to be stored (NAME?). The ABC indicator on the top of the display indicates that the phone is in the alpha mode. 2 Enter the name as described above and press OK, or if you do not want to store a name, press OK.
c1caus.frm Page 24 Thursday, December 19, 1996 12:46 PM d) If both the phone number and name you entered are already in the phone's memory, the message ALREADY STORED is briefly displayed and then the phone suggests you to move the information to the first empty memory location (e.g., MOVE TO 5?) or prompts you to enter a memory location number if there is no empty memory location (MOVE TO?). Press OK or first enter the memory location number and then press OK.
c1caus.frm Page 25 Thursday, December 19, 1996 12:46 PM To begin scrolling from a memory location: Enter a location number and start scrolling forward or backward from the entered location number by using the key. • If the location you entered is empty, the message LOCATION EMPTY will be briefly displayed, and the phone then displays the next memory location in use.
c1caus.frm Page 26 Thursday, December 19, 1996 12:46 PM To recall information by location number: 1 Press the MENU key and scroll to the menu function FIND NAME by using the key and press OK, or press MENU 2 as a shortcut access method. The phone asks you to enter the name to be recalled (NAME?). 2 Press the ABC key instead of entering the name.The phone now prompts you to enter the location to be recalled (LOCATION?).
c1caus.frm Page 27 Thursday, December 19, 1996 12:46 PM To move the contents of a memory location: 1 Recall the phone number and name to be moved as described in Recalling Names and Phone Numbers on page 25. 2 Press the MENU key and scroll to the menu function STORE TO MEMORY by using the key and press OK, or press MENU 1 as a shortcut access method. The message ALREADY STORED is briefly displayed, and then the phone prompts you to move the information to the first empty memory location (e.g.
c1caus.frm Page 28 Thursday, December 19, 1996 12:46 PM 2 Enter the name or the first letter(s) of the name you want to erase and press OK, or start scrolling by using the key. The name, or if you entered the first letter(s) only, the first name beginning with the letter(s) is displayed. To display the associated phone number, press the ABC key. You can view other stored names in alphabetical order by using the key.
c1caus.frm Page 29 Thursday, December 19, 1996 12:46 PM The phone number stored in the selected location will be displayed. To see the associated name, if entered, press the ABC key. Use the key to view other memory locations in use. • If the selected memory location is empty, the message LOCA- TION EMPTY is briefly displayed, and the phone exits the erase function if you pressed OK.
c1caus.frm Page 30 Thursday, December 19, 1996 12:46 PM 6. USING THE MENU FACILITY The phone offers you a set of functions arranged in menus accessible through the phone display. Each menu allows you to review and alter the settings of a specific menu function. The menu functions can be accessed by scrolling through the menu facility (Menu Method) or by using the Shortcut Method. The menu number of the accessed function will be displayed in the upper right corner of the display.
c1caus.
c1caus.frm Page 32 Thursday, December 19, 1996 12:46 PM STORE TO MEMORY (MENU 1) This menu function allows you to store names and phone numbers in the phone’s memory locations. 1 Press the MENU key and scroll to the menu function STORE TO MEMORY by using the key and press OK, or press MENU 1 as a shortcut access method. The phone asks you to enter the name to be stored (NAME?). 2 Enter the name as described in the section Entering Names and press OK or if you don't want to store a name, press OK.
c1caus.frm Page 33 Thursday, December 19, 1996 12:46 PM The name, or if you entered the first letter(s) only, the first name beginning with entered letter(s) is displayed. To display the associated phone number, press the ABC key. You can view other stored names in alphabetical order by using the key. • If no matching name is found, the message NAME NOT FOUND will be briefly displayed, and the entered characters will reappear on the display if you pressed OK.
c1caus.frm Page 34 Thursday, December 19, 1996 12:46 PM • If you started scrolling without pressing OK, the message NAME NOT FOUND will be briefly displayed, and the next name in alphabetical order will then be displayed. 3 When the desired name is displayed, press OK, if you want to erase the memory location. The message ERASED is briefly displayed confirming that the memory location has been erased, and then the phone displays the next name.
c1caus.frm Page 35 Thursday, December 19, 1996 12:46 PM When the phone is locked: All incoming calls can be received by pressing the SEND key. Storing in the phone's memory and recalling the last dialed numbers is prevented. Note: When the phone is locked, calls may be possible to the emergency number programmed into your phone (e.g., 911 or another official emergency number) including calls by one-touch emergency dialing.
c1caus.frm Page 36 Thursday, December 19, 1996 12:46 PM To select the roaming mode: 1 Press the MENU key and scroll to the menu function SYSTEM SELECT by using the key and press OK, or press MENU 5 as a shortcut access method. The phone will display its current roaming mode. Scroll through the four roaming options by using the key: HOME TYPE B* The phone uses only its home system(B). NON-HOME TYPE A* The phone uses only the non-home type system (A).
c1caus.frm Page 37 Thursday, December 19, 1996 12:46 PM LAST ..... : .. Shows the duration of the last or current call in minutes and seconds. TOTAL 1..... : .. Shows the duration of all calls you have made for your primary number (not including the call in progress). TOTAL 2..... : .. Shows the duration of the calls you have made for your optional second phone number. (See NAM SELECT on page 40.) CLEAR TIMERS Resets the call duration timers to zero.
c1caus.frm Page 38 Thursday, December 19, 1996 12:46 PM When set to LIGHTS OFF: • and the phone is used as a handportable phone or connected to a charger, the lights remain off continuously. • and the phone is connected to a hands-free car kit, the lights remain on for 15 seconds after you have pressed a key or an incoming call alert has been received. KEYPAD TONES (MENU 8) A short tone is sounded each time you press a key of your phone. This menu function allows you to set the keypad tones on or off.
c1caus.frm Page 39 Thursday, December 19, 1996 12:46 PM RINGING TYPE This menu function allows you to select and demonstrate any of the five ringing tone types of your phone. 1 Press the MENU key and scroll to the menu function RINGING TYPE by using the key and press OK. 2 Scroll through the options (RINGING TYPE 1 to 5) by using the key. • A sample tone is automatically played to demonstrate each displayed option. 3 To select the displayed option, press OK.
c1caus.frm Page 40 Thursday, December 19, 1996 12:46 PM NAM SELECT Your phone can have two phone numbers. This menu function allows you to select the network to be used for making or receiving call, if you are a subscriber to two cellular networks. Each phone number is stored in a NAM (Number Assignment Module). Note: The phone cannot operate on both networks at the same time, and you cannot change the network during a call.
c1caus.frm Page 41 Thursday, December 19, 1996 12:46 PM CALLING CARD Note: This feature may not be operational in all countries. This menu function allows you to activate a calling card option to be used for card calls. You can select the calling card option among the calling card companies programmed into your phone, or you can select the NO CARD option. For making an automatic calling card call, see Calling Card Call on page 19.
c1caus.frm Page 42 Thursday, December 19, 1996 12:46 PM 7. ADDITIONAL FEATURES Sending DTMF Tones The Dual Tone Multi Frequency (DTMF) feature allows you to send touch tones which can be used to control equipment such as bank-by-phone or voicemail by using your cellular phone. There are two alternative ways to send DTMF tones: 1. Manual Transmission 1 Make a call to the desired number in the usual way (e.g., to your bank’s computer phone number). 2 Enter the digits you want to be sent as DTMF tones (e.g.
c1caus.frm Page 43 Thursday, December 19, 1996 12:46 PM Adding a Pause Character If the device to which you are sending the DTMF string, needs to receive the number slowly or after a pause, insert one or more pause characters of 2.5 seconds between the required DTMF digits. To create a pause character (p): 1 Press the MENU key first and then the # key. (For example, if you want to send your password as DTMF tones with a 'p' character between each digit, the string should be sent as 1p2p3p4.
c1caus.frm Page 44 Thursday, December 19, 1996 12:46 PM 8. BATTERY INFORMATION Battery Options The following battery options are available for your phone. Consult your local dealer for more information. Battery charging times depend on the remaining battery charge and the type of battery and charger used. Charging Times: BATTERY ACH-6A/LCH-6/LCM-1 Daily Calling Battery BBT-6S 1 h 30 min. 950 mAh NiCd Marathon Battery BBT-6H 1700 mAh NiMH 3h Note: The above charging times are approximate.
c1caus.frm Page 45 Thursday, December 19, 1996 12:46 PM Discharging a Battery A battery lasts longer and performs better if allowed to discharge fully from time to time. You can do this by leaving the phone switched on until the phone turns off automatically after the battery has been completely discharged. Alternatively, you may use the battery discharge feature of any approved accessory available for your phone. Note: Do not attempt to discharge the battery by any other means.
c1caus.frm Page 46 Thursday, December 19, 1996 12:46 PM • Do not short circuit the battery. Accidental short circuiting can occur when a metallic object (coin, clip or pen) causes direct connection of the + and - terminals of the battery (metal strips on the back cover of the battery) e.g., when you carry a spare battery in your pocket or purse. Short circuiting the terminals may damage the battery or the connecting object.
c1caus.frm Page 47 Thursday, December 19, 1996 12:46 PM 9. ACCESSORIES General A new extensive range of accessories is available for your phone. You can select the accessories that accommodate your specific communication needs. For availability of the accessories, please check with your local dealer. A few practical rules for accessory operation: • Keep the accessories out of small children's reach. • When you disconnect the power cord of any accessory, grasp and pull the plug, not the cord.
c1caus.frm Page 48 Thursday, December 19, 1996 12:46 PM CGH-4 Office Desktop Stand The Office Desktop Stand provides you with a compact solution to keep your phone and spare battery in a ready-touse, upright position. Plug your charger into the back of the stand and into a wall outlet. Place the phone and/or spare battery in the stand. The phone battery will be charged first, then the spare battery. The Office Desktop Stand can be used together with the Fast & Light Charger ACH-6.
c1caus.frm Page 49 Thursday, December 19, 1996 12:46 PM Vehicle Accessories LCH-6 Mobile Charger The multivoltage Mobile Charger ensures that you can charge your phone battery wherever you travel. Its stylish and functional design fits well in most car lighters and interiors. Plug the charger into your car’s cigaretter lighter socket and connect the lead to the bottom of your phone. A green light indicates that the chargeris ready to charge. Check the charging status from the phone display.
c1caus.frm Page 50 Thursday, December 19, 1996 12:46 PM LCM-1 Mobile Installation Charger The multivoltage Mobile Installation Charger powers your phone from the car battery when the ignition is on and leaves the cigarette lighter vacant. The charging time for a phone manufacture approved 950 mAh battery is about 1 h 30 minutes. You can use the charger in any vehicle with a 12 or 24 V DC connection, negative grounding. Note: The installation must be made by qualified personnel only.
c1caus.frm Page 51 Thursday, December 19, 1996 12:46 PM HSU-2 Light Handset The Light Handset with no display or keypad provides privacy for conversation. When you lift the Light Handset from its holder, the loudspeaker and microphone will be muted and you can speak in privacy. When you replace the handset in its cradle, the call is terminated unless you have pressed the MENU key on your phone in order to return to the handsfree mode. Note: The installation must be made by qualified personnel only.
c1caus.frm Page 52 Thursday, December 19, 1996 12:46 PM CARK-53 Complete Handsfree Car Kit You may choose the Complete Handsfree Car Kit to provide a convenient charging facility combined with external antenna connection and handsfree capability, as well as, privacy. • The Phone Holder MBT-3 keeps your phone firmly in place. • The Compact Handsfree Unit PHF-5 with its internal speaker and Handsfree Microphone HFM-7 offers you a seamless handsfree function.
c1caus.frm Page 53 Thursday, December 19, 1996 12:46 PM 10. APPENDIX Care and Maintenance Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and allow you to enjoy this product for many years. • Keep the phone and all its parts and accessories out of small children's reach. • Keep the phone dry. Precipitation, humidity and liquids contain minerals that will corrode electronic circuits.
c1caus.frm Page 54 Thursday, December 19, 1996 12:46 PM Troubleshooting If the power does not come on or stay on: • Make sure the battery is properly installed and charged. • Be sure that the contacts on the battery and the charging stand are clean. • Battery charge lmay be too low for operation. Check the dis- play and listen for the low battery warning tones. If the power comes on, but the phone does not work: • Check the NO SVC indicator, you might be out of the cellular service area.