CCS Technical Documentation NPM-2NX Series Transceivers Service Software Instructions & Service Concepts Issue 1 07/02 ãNokia Corporation
NPM-2NX Service Software Instructions & Service Concepts Contents CCS Technical Documentation Page No Service Software Instructions ........................................................................................ 3 Phoenix ........................................................................................................................3 Supported Operating Systems ................................................................................... 3 Hardware requirements for using Phoenix...
NPM-2NX Service Software Instructions & Service CCS Technical Documentation Service Software Instructions Phoenix Phoenix is the next generation Service Software and it has been designed to meet the challenges in servicing modern cellular phones. The Phoenix program has been built using component architecture. This means that the actual program is small and most of the program’s functionality is divided into dynamically loaded modules or DLLs.
NPM-2NX Service Software Instructions & Service Concepts CCS Technical Documentation Introduction This section briefly describes how to install the Phoenix software and includes some basic information on how to use the program. For more detailed information, please refer to the Phoenix’s Help -files. Each feature in Phoenix has its own Help function, which can be activated while running the program. Press the F1 key or the feature's Help-button to activate a Help -file.
NPM-2NX Service Software Instructions & Service CCS Technical Documentation Uninstalling Phoenix Uninstalling another Phoenix version 1 Make sure that the dongle is attached. 2 Go to the Control Panel and select Add/Remove Programs. 3 Select TSS4 Phoenix Release xx.yy.zzz for uninstallation and click Add/Remove. 4 Click OK to remove the application You may be required to reboot your PC after uninstallation.
NPM-2NX Service Software Instructions & Service Concepts CCS Technical Documentation nection setup dialog. Selecting a product Many of Phoenix’s features are product-specific. It is, therefore, mandatory to choose the product you will be working on at the beginning of the session. 1 Select File - Scan Product (or hold the Ctrl key down and press R). Phoenix will scan the connected product and load additional menus which are designed for the product.
NPM-2NX Service Software Instructions & Service CCS Technical Documentation Service Concepts - Flashing and Testing Setups POS Flash (FLS-4, 0081482 - Setup 1) This setup is made for Point-Of-Sale use, but it also can be used in service centers. The purpose of this is to make flashing as easy as possible in POS’s and to prevent the unnecessary handset flow to service.
NPM-2NX Service Software Instructions & Service Concepts CCS Technical Documentation Flashing, testing, and tuning with covers on (Setups 2a, 2b, and 2c) Tightened performance specifications require more precise equipment and methods for testing and alignment. Manual tuning can’t provide accurate results for NPW-2NX products, which means that this task has to be automated. These setups are intended to be used with either Phoenix or Darium SW.
CCS Technical Documentation NPM-2NX Service Software Instructions & Service Service Tool Setup 2a This setup is for flashing, testing and tuning (RF testing and tuning is not possible). Figure 2: View of FPS-8 Flash concept To accomplish the EM calibration, the JBV-1 must be powered by 12V external power supply. The EM calibration can also be done by connecting the JBV-1 to a PC using a DAU-9S cable. Figure 3: View of Jig concept Service Tool Setup 2b RF testing and tuning is possible with this setup.
NPM-2NX Service Software Instructions & Service Concepts CCS Technical Documentation Service Tool Setup 2c This setup makes antenna go/no go testing possible.
NPM-2NX Service Software Instructions & Service CCS Technical Documentation Flashing and testing with covers off (Setup 3) Item Name Type Code 3 Service cable XCS-4 0730178 4 DC cable PCS-1 0730012 6 Flash loading adapter FPS-8 0750123 7 D9-D9 cable AXS-4 (included in FPS-8C sales pack) 0730090 8 Printer cable, IEEE 1284 parallel cable AXP-8 (included in FPS-8C sales pack) 073F000 9 AC charger (included in FPS-8 sales pack) ACF-8 0680032 10 Software protection key PKD-1 0750
NPM-2NX Service Software Instructions & Service Concepts CCS Technical Documentation Parallel Flash (Setup 4) The Parallel Flash setup allows flashing eight individual handsets at the same time. This requires the PC to fulfill the following requirements: the PC has to have two physical serial ports (COM 1 and COM2).
