CCS Technical Documentation RH-12/RH-28 Series Transceivers 4 - Service tools Issue 1 02/04 Nokia Corporation
RH-12/RH-28 Service Tools CCS Technical Documentation [This page left intentionally blank] Page 2 Nokia Corporation Issue 1 02/04
RH-12/RH-28 Service Tools CCS Technical Documentation Table of Contents Page No List of service tools ........................................................................................................ 5 JBV-1 Docking station................................................................................................... 6 DA-8 Docking station adaptor ....................................................................................... 7 SA-17 RF adaptor ..........................................
RH-12/RH-28 Service Tools CCS Technical Documentation [This page left intentionally blank] Page 4 Nokia Corporation Issue 1 02/04
RH-12/RH-28 Service Tools CCS Technical Documentation List of service tools The table below shows the set of tools that can be used for testing, error-analysis and repair of the RH-12/RH-28 product.
RH-12/RH-28 Service Tools CCS Technical Documentation JBV-1 Docking station The JBV-1 docking station is a general tool that has been designed for calibration and software update use. The DA-8 docking station adaptor is a product-specific tool that provides signal connections to the phone. The JBV-1 and the DA-8 are used as one unit.
RH-12/RH-28 Service Tools CCS Technical Documentation DA-8 Docking station adaptor The docking station adaptor is used for the RH-12/RH-28 in combination with the JBV-1. The DA-8 supports flashing and energy management calibration. If used in conjunction with the SA-17, a RF Go/NoGo test can be performed. The MMC card is to be removed before mounting the phone on the docking station adaptor.
RH-12/RH-28 Service Tools CCS Technical Documentation SA-17 RF adaptor The SA-17 RF adaptor provides a galvanic connection to the RF output. The adaptor is intended for a Go/NoGo test. By removing the A&B covers and the antenna, the RF adaptor can be attached on the top section of the phone. The adaptor is designed to be used with the DA-8 docking station adaptor or the SF-7 POS flash adaptor.
RH-12/RH-28 Service Tools CCS Technical Documentation MJ-12 Module repair jig The MJ-12 Module repair jig is designed for Regional service centers to allow component level trouble shooting and testing.
RH-12/RH-28 Service Tools • CCS Technical Documentation Pogo pins used for SIM connection (needs soldering) (0770442) View of MJ-12 Note: The supply voltage for the MJ-12 has to be kept within the range of 8-12 V when using the built in regulator. When bypassing the regulator (IMEI rewrite), the voltage must be kept below 5,4V.
RH-12/RH-28 Service Tools CCS Technical Documentation RJ-9 Soldering Jig The RJ-9 soldering jig is used for soldering and reworking for the ez4a Main board.
RH-12/RH-28 Service Tools CCS Technical Documentation SES-3 Rework Stencil The SES-3 Rework Stencil is used for PA Chip N700 (LGA type component) rework. It is used together with the Rework Jig soldering paste spreader.
RH-12/RH-28 Service Tools CCS Technical Documentation FPS-8 Flash Prommer (Sales Pack) The Flash Prommer FPS-8 is used with e.g. DA-8 and JVB-1. Power is supplied to FPS-8 from the Universal Power Supply.
RH-12/RH-28 Service Tools CCS Technical Documentation FPS-8C Parallel Flash Prommer (Sales Pack) The Parallel Flash Prommer FPS-8C is used with DA-8 and JVB-1. Flash programming can be done to maximum of 8 phones parallel. FPS-8C consists of eight SF11C programming cards. The SF11C card is functionally identical to FPS-8.
RH-12/RH-28 Service Tools CCS Technical Documentation ACF-8 Universal Power Supply The ACF-8 Universal Power Supply is used to power FPS-8. ACF-8 has 6 V DC and 2.1 A output.
RH-12/RH-28 Service Tools CCS Technical Documentation SF-7 POS flash adaptor The SF-7 is a POS flash adaptor provided for the RH-12/RH-28 phones.
RH-12/RH-28 Service Tools CCS Technical Documentation XCS-1 Service Cable The XCS-1 Service Cable is used to connect FLS-4 to FLA-27.
RH-12/RH-28 Service Tools CCS Technical Documentation FLS-4S POS (Point Of Sale) Flash Device (Sales Pack) FLS-4S is a dongle and flash device incorporated into one package, developed specifically for POS use.
RH-12/RH-28 Service Tools CCS Technical Documentation PCS-1 Power Cable The PCS-1 Power Cable (DC) is used to connect e.g. JVB-1 to FPS-8.
RH-12/RH-28 Service Tools CCS Technical Documentation XRF-1 RF Cable RF cable XRF-1 is used to connect e.g. Module Jig MJS-38 to RF measurement equipment.
RH-12/RH-28 Service Tools CCS Technical Documentation DAU-9S MBUS Cable The MBUS Cable DAU-9S has a modular connector, and is used with between PC's serial port and e.g. Module Jig MJS-38.
RH-12/RH-28 Service Tools CCS Technical Documentation SCB-3 DC Cable The DC Cable SCB-3 is used to connect e.g. JVB-1 to the phone.
RH-12/RH-28 Service Tools CCS Technical Documentation XCS-4 Modular Cable XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing and service purposes.
RH-12/RH-28 Service Tools CCS Technical Documentation Printer Cable This cable is used to connect the PC to FPS-8.
