CCS Technical Documentation RH-12/RH-28 Series Transceivers 9 - Car Installation Kit Issue 1 02/04 Nokia Corporation
RH-12/RH-28 Car Installation Kit CCS Technical Documentation [This page left intentionally blank] Page 2 Nokia Corporation Issue 1 02/04
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Table of Contents Page No Introduction .............................................................................................................................................. 5 Installation guide for CARK126........................................................................................................... 6 Introduction ................................................................................................................
RH-12/RH-28 Car Installation Kit CCS Technical Documentation [This page left intentionally blank] Page 4 Nokia Corporation Issue 1 02/04
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Introduction RH-12/RH-28 will support several car kits and solutions for handsfree operation as listed in Chapter 1. A comprehensive documentation for the accessories is found from the relevant accessory programs.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Installation guide for CARK126 Introduction This installation guide provides the basic information required to install the CARK126. This guide is not intended to be definitive, because different vehicle types and models will require different installations. The information given is for general guidance only. The terms of warranty require that this car kit be installed by an experienced installer and using only genuine Nokia parts.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Warnings 1 ENSURE THAT THE VEHICLE’S BATTERY IS DISCONNECTED BEFORE YOU START THE INSTALLATION PROCEDURE, AND THAT IT REMAINS DISCONNECTED DURING THE PROCEDURE. 2 DO NOT SMOKE OR USE OPEN FLAMES WHEN WORKING NEAR THE VEHICLE’S FUEL SYSTEM. 3 ENSURE THAT THE VEHICLE’S ELECTRICAL CABLES, HYDRAULIC LINES, FUEL LINES AND SAFETY EQUIPMENT ARE NOT DAMAGED DURING INSTALLATION.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Components of CARK126 Figure 1: The CARK126 includes the above parts. Please note that the items surrounded by broken lines are not supplied with the CARK126 in Europe and Asia. In the US, Canada and Latin America other sales packages than the CARK126 exist. The main difference is that the mobile holder and antenna coupler are included instead of being sold separately. External antenna AMD-2 is not sold in the US, Canada and Latin America.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Swivel mount HHS-15 and Mounting plate MKU-1 The HHS-15 is a swivel mount which offers two installation methods for the MBC-15S holder. Either use all the components to make a swivel mounting, or use the flat mounting plate for a fixed position. For an exploded view, see the following figure. Figure 2: Mounting plate MKU-1 The HFU-4 handsfree unit is attached to the vehicle’s interior using the MKU-1 mounting plate.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Power cable PCU-4 The power cable connects to the DC socket in the HFU-4 and to the vehicle's power supply. See section "Installation" for more information. HF microphone HFM-8 The HF microphone connects to the MIC socket in the HFU-4. Turn the plug clockwise to lock it firmly in place. External HF speaker HFS-12 The external HF speaker connects to the SPEAKER socket in HFU-4. Twist the plug clockwise to lock firmly in place.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Installation Refer to the cover for an example of installation positions. The HFU-4 and the different parts are connected as mentioned in the section "Component parts". There are some important aspects that require special attention when positioning the car kit accessories. The location of the holder should be selected so that the visibility of the phone’s display is good and the driver’s attention is not distracted.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Ignition sense IGNS The ignition sense feature prevents your car kit from draining the car battery by executing an auto power off in 20 seconds after the ignition key has been turned off. The blue cable from PCU-4 is used for the ignition sense feature. The use of ignition sense is recommended to prevent accidental draining of the car battery. The cable is connected via a 1 A fuse to a 12 volt supply that is controlled by the ignition key.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation ate the vehicle in any way.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Installation guide for CARK112 Introduction This installation guide has been prepared to provide the basic information necessary to install the car kit. This guide is not intended to be definitive, because different types and models of vehicles will require different installation work. The information given is for general guidance only.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation 7. THE PHONE SHOULD NOT BE LEFT SWITCHED ON FOR EXTENDED PERIODS WITHOUT RUNNING THE VEHICLE’S ENGINE. FAILURE TO COMPLY COULD DRAIN THE VEHICLE’S BATTERY.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Unpacking Carefully unpack the equipment and ensure that the following items are present.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Wireless HF Unit HFW-1 Figure 5: INTERNAL BLUETOOTH ANTENNA SPEAKER MIC REMOTE PHONE DC The HFW-1 is used in a fixed car installation and it offers a wireless handsfree function, a fast charging function when a phone is connected into it by a charging cable (phone specific, not supplied with CARK-112) and a wireless connection to external devices. The HFW-1 unit is attached to the vehicle interior using the mounting plate MKU-1.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation Mounting Plate MKU-1 MKU-1 is a fixed position mounting plate. It is used to attach Wireless HF Unit (HFW-1) to the vehicle. Remote Control Button CUW-2 mote Control Button (CUW-2) allow The Remote Control Button (CUW-2) allows convenient operation of the phone. The car installation includes a Remote Control Button CUW-2, which is connected to the HFW-1 with a cable (REMOTE socket).
RH-12/RH-28 Car Installation Kit CCS Technical Documentation 1. 3. 2. 4. HF Microphone HFM-8 The HF microphone should be installed according to the directions in the separate microphone installation guide. Ensure the microphone is as close to the driver’s mouth as possible, and attached to a surface that is mechanically quiet. The microphone should be mounted at least 3 ft./1 m away from the handsfree unit speaker to avoid acoustic feedback.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation BLUE IGNS YELLOW CRM RED BLACK 12V Cables Ensure cables are routed as far away as possible from the vehicle’s electronic systems (refer to WARNINGS)*. Also, ensure that cables are not subjected to undue mechanical stress e.g. under seats or against sharp edges. * To prevent disturbance, cables should be routed as far away from the interference source as possible.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation VEHICLE RADIO HFW–1 CRM line yellow wire CRM line Testing Once installed, the equipment should be tested to ensure that it is operating satisfactorily and that the position of the units does not impair on the driver’s ability to control and operate the vehicle in any way. You can reset the car kit to the original settings, for example, to change the default user of the car kit.
RH-12/RH-28 Car Installation Kit CCS Technical Documentation [This page left intentionally blank] Page 22 Nokia Corporation Issue 1 02/04
