Programme’s After Market Services NME–3 Series Transceivers Installation instructions Issue 1 10/99
NME–3 Installation instructions PAMS Technical Documentation Contents Page No Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Component Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Bracket MBE–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NME–3 PAMS Technical Documentation Installation instructions Introduction This installation guide has been prepared to provide the basic information necessary to install mobile phone. This guide is not intended to be definitive, because different types and models of vehicle will require different installation work. The information given is for general guidance only. The terms of warranty demand that this mobile phone be installed by an experienced installation facility.
NME–3 PAMS Technical Documentation Installation instructions Unpacking Carefully unpack the equipment and ensure that the following items are present. Figure 1. Equipment listing diagram Page 4 Item/Product Name: Type: Remarks: 1. Transceiver 2. Handset 3. Handsfree speaker 4. Handsfree microphone 5. System cable +bracket 6. Mounting bracket complet 7. Handset cradle 8. Mounting plate CRD–8 9.
NME–3 PAMS Technical Documentation Installation instructions Component Parts Mounting Bracket MBE–2 The mounting bracket MBE–2 shall be installed using three screws. The bracket itself can to a certain degree compensate for unevenness of the mounting surface. However, should additional spacers be required, two different types are supplied with the bracket.
NME–3 PAMS Installation instructions Technical Documentation Handsfree Microphone HFM–15 and Handsfree Speaker HFS–10 The safest and easiest way to have call while driving is use the handsfree option. The system consist of two components, the microphone HFM–15 and loudspeaker HFS–10. The microphone needs to be as close to the drivers mouth as possible and attached to a surface that is mechanically quiet.
NME–3 PAMS Technical Documentation Installation instructions The handsfree microphone can be installed on the driver’s sunvisor or the A–pillar. Ensure the microphone is as close to the driver’s mouth as possible, and attached to a surface that is mechanically quiet. The microphone should be mounted at least 3 ft/1 m away from the handsfree unit speaker to avoid acoustic feedback. The loudspeaker isn’t so sensitive for vibrations, thus it can be located more freely.
NME–3 PAMS Installation instructions Technical Documentation Try to route the antenna cable so that possible sources of disturbances are avoided, as well anti–skid brake systems. The shorter the antenna cable, the smaller the attenuation, and the better the performance of the antenna. The antenna coupler should always be connected to the antenna via a non–radiating cable (e.g. coax).
NME–3 PAMS Technical Documentation Installation instructions Figure 2. Reducer Some vehicles have a main switch (e.g. gas trucks), which separates the vehicles chassis from the negative lead of the battery. Do under no circumstances pass this switch, i.e. the grounding of the reducer must be taken from the body of the vehicle, NOT directly from the battery. WARNING : DO NOT INSTALL REDUCER – To engine compartment – Where there isn’t adequate amount of air for cooling (under the carpet, etc.
PAMS NME–3 Installation Instructions Technical Documentation When a relay is used, connect of series with the car radio main supply. A 100 mA fuse should be used to protect the XCRM output in event of a short circuit. Some radios have separate supplies for amplifiers and motors, and another for memory backup purposes. Very often these radios also have a secret code system, which activates itself if a break in the memory supply is detected.
NME–3 PAMS Technical Documentation Installation instructions Power Antenna Control (ANTC) The orange wire of the system cable (ANTC) may be used to control different devices on and off. The voltage in this output is +12 V whenever the phone is on. If the phone is turned off, the voltage disappears. The maximum output current is 180 mA, therefore for example motorized antenna must be controlled via a relay, see picture below. Bosch P/N 0–332–204–150 12 V, 30 A. SPDT CONTROLLED DEVICE, e.g.
NME–3 Installation instructions PAMS Technical Documentation [This page intentionally left blank] Page 12 Issue 1 10/99
