PAMS Technical Documentation NSM–5 Series Transceivers Service Software Instructions Issue 1 02/2002 Nokia Corporation
NSM–5 Service Software Instructions PAMS Technical Documentation CONTENTS Service Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware requirements for Windows 3.11 . . . . . . . . . . . Hardware requirements for Windows 95, 98 & NT . . . . Software Environment of the Support Modules . . . . . . . . . Servicing Equipment . . . . . . . . . . . . . . . . . . . . . .
PAMS Technical Documentation NSM–5 Service Software Instructions New command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Open... command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Initialise... command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Band... command . . . . . . . . . .
NSM–5 Service Software Instructions PAMS Technical Documentation Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equipment Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equipment Setup for Testing . . . . . . . . . . . . . . . . . . . . . . . . . Flash Concept with JBU–6 . . . . . . . . . . . . . . . . . . . . . . . . . . Testing Without Covers – Using Test–frame MJS–9 . . . . . Flashing With FLA–10 . . . . . . . . . . . . . . . . .
PAMS Technical Documentation NSM–5 Service Software Instructions Service Software General To run the Service Software, a parallel port software protection device (PKD–1) has to be connected. TDF–4 box must connected to PC for flashing purposes. The test functions send test messages from PC to mobile stations (MS) and receive results and show them in the PC display. The messages can be sent via M2BUS or FBUS. Note: if this software is to be run on laptops, the power saving feature MUST be switched off.
NSM–5 Service Software Instructions PAMS Technical Documentation Servicing Equipment NSM–5 specific: Service SW disk 3.5” for NSM–5 0774080 Flash SW packages on CD global 0775314 RJ9 Connector Module for MJS–9 0201398 RAF–5 RF Adapter for JBU–6 0770396 MJS–75 Soldering Jig for NSM–5 0770233 Common to other models but needed also for NSM–5: Service SW WinTesla disk 3.
PAMS Technical Documentation NSM–5 Service Software Instructions Modular Cable Jack Connector (available e.g. as AMP code: P/N 555052–1) *) Note: A number of PC’s of an older generation use the Intel, National Semiconductor, or United Microelectronics IC 8250 as the serial port UART. This is a comparatively inefficient circuit for current purposes and does not necessarily support the M2BUS adapter at 9600 baud.
NSM–5 Service Software Instructions PAMS Technical Documentation Installing the Service Software on PC Hard Disk The program is delivered on a diskette and is copy protected with a dongle PKD–1. It must be present in parallel port when using Service software. The program must be installed on the hard disk before use.
PAMS Technical Documentation NSM–5 Service Software Instructions Start installation, double–click the dk2wn32.exe file. Follow the instructions on the screen. When installation has finished remove the dongle driver software disk from your floppy drive. Continue with the support modules installation.
NSM–5 Service Software Instructions PAMS Technical Documentation Common Properties of the User Interface This chapter describes how the User Interface CLF (Common Look and Feel) must appear to the user. The User Interface MUST be capable of being driven without the use of a mouse, as the service engineer rarely has space on the bench to use a mouse.
PAMS Technical Documentation NSM–5 Service Software Instructions Cancel button (ESC) The Dialog box is closed and application is started, but the Faultlog feature is disabled. Help button (F1) Activates the Windows Help application and displays context sensitive Help. Main Window Title bar The title bar is located at the top of the window.
NSM–5 Service Software Instructions PAMS Technical Documentation The status bar texts are explained in detailed in each of command’s description. The right areas of the status bar indicate which of the following keys are latched down: Indicator Description USER Entered Login ID. CAP The Caps Lock key is latched down. NUM The Num Lock key is latched down. SCRL The Scroll Lock key is latched down. Tool bar The tool bar is NOT defined and will not be implemented until specified by this document.
NSM–5 Service Software Instructions PAMS Technical Documentation Menu Bar The Service Software package will have two menu bar configurations. The first, is an abbreviated version that contains the minimum number of menus that allows package configurations when a phone is NOT connected.
NSM–5 Service Software Instructions PAMS Technical Documentation Configure The Configure menu contains at least the following items: • Options... • Directories... • Faultlog... • Phone Type Specific configuration items (where applicable) Tuning The Tuning menu contains at least the following menu sections: • RX Filter Calibration... • RX Calibration... • AM Suppression... • Tx Power... • Tx I/Q... • Energy Management Calibration...
PAMS Technical Documentation NSM–5 Service Software Instructions Software The Software menu contains at least the following menu sections: • Product Profile... • Start Up Self–tests... • Set Factory Values • Phone Identity... • Warranty State... • Production Data Edit... Dealer The Dealer menu contains at least the following menu sections: • User Settings... • Short Code Memory... • SCM & User settings ... • Restore User Defaults... • Set UI/DEV Default Values ... • Operators Settings... • IWR Swap...
NSM–5 Service Software Instructions PAMS Technical Documentation Phone Identity Window The Phone Identity window should contain, as a minimum, the following data: • Software Version(s) • Hardware Version(s) • Serial Number(s) • Product Code This window will only be used as a display window and therefore will not allow editing of the displayed data. This window will not contain any controls other than a scroll bar.
PAMS Technical Documentation NSM–5 Service Software Instructions Mouse Cursors The standards Windows pointer will be used as the mouse cursor. During time consuming tasks e.g. communication to phone, an hour glass will be shown informing the user that a task is in progress. The application uses the hour glass cursor to inform user that the application has taken the control and any actions from user will be ignored.
NSM–5 Service Software Instructions PAMS Technical Documentation Shift Hot Keys Key by Description Defined Shift+F5 Local Mode NMP Key by Description Defined Alt+P Product Menu NMP Alt+P,N New NMP Alt+P,O Open NMP Alt+P,C Close NMP Alt+P,I Initialize Pop–up NMP Alt+P,I,N Normal Mode NMP Alt+P,I,L Local Mode NMP Alt+P,B Band NMP Alt+P,F Faultlog Pop–up NMP Alt+P,F,A Activate Faultlog NMP Alt+P,F,E Edit Faultlog NMP Alt+P,X Exit Application NMP Alt+C Configure
PAMS Technical Documentation NSM–5 Service Software Instructions Alt+E,S Self Tests NMP Alt+E,A ADC Readings NMP Alt+E,D Audio NMP Alt+E,U User Interface NMP Alt+E,I IR Test NMP Alt+E,M Sleep Mode Test NMP Alt+E,V Vibra Test NMP Alt+S Software Menu NMP Alt+S,P Product Profile NMP Alt+S,S Start–up Self Tests NMP Alt+S,V Set Default Values NMP Alt+S,I Phone Identity NMP Alt+S,W Warranty State NMP Alt+S,D Production Data Edit NMP Alt+D Dealer Menu NMP Alt+D,U Use
NSM–5 Service Software Instructions PAMS Technical Documentation Help Functions The Help User Interface will be the standard Windows help tool called WinHelp. The context sensitive help is activated with F1–key. Help contains also Using Help which describes how to use help facility. Refer to the Windows manual for detailed description on the Windows Help. Dialog boxes The Service Software application uses many different dialog boxes. Dialog boxes are used to display data and prompt the user for input.
PAMS Technical Documentation NSM–5 Service Software Instructions The dialog box will also contain a Yes button, a No button, and a Help button. Yes button (Alt+Y or Y) (default key): Accepts confirmation or question. No button (Alt+N or N): Denies confirmation or question. Help button (Alt+H): Opens context sensitive help as F1–key does. The buttons may also be OK and Cancel. The operation of these buttons are the same as in the Note dialog box.
NSM–5 Service Software Instructions PAMS Technical Documentation Custom Dialog boxes All custom dialog boxes will contain the predefined buttons as defined below in the section – Buttons. However, it is recognised that features may require additional button types, but the addition of these non–standard buttons should be carefully considered to minimise any inconsistencies between implementations. The buttons will be positioned down the right–hand side of the dialog boxes.
PAMS Technical Documentation NSM–5 Service Software Instructions Replies Yes to a question asked of the user. No button (ALT+N or N): Replies No to a question asked of the user. Help button (ALT+H): Opens context sensitive help as F1–key does. Reporting Status The status bar will be used to report the present status to the user. When a feature is initiated, the status bar will be updated with a brief description of the function.
NSM–5 Service Software Instructions PAMS Technical Documentation NSM–5 FEATURES Menu bar After Sales SW’s menus follow the menu structure specified in WinTesla User Interface Specification. This specification will describe functionality that differs from WinTesla specification. Product New command Activation Status Bar Text Alt, P, N Rescan a new phone Ctrl+R If phone is changed (with same phone type only serial number is changed) phone will be initialised to local/normal mode (selected in TESLA.
PAMS Technical Documentation NSM–5 Service Software Instructions Normal Mode Activation Status Bar Text Alt, P, I, N Initialises phone to normal mode F5 When normal mode has been activated or program has been started, self–test results will be asked from MCU. If fault was found in the tests, an error message is shown. If normal mode has been set successfully (no self test error has been found), and paging listening has been started, the used AFC value is requested from MS.
NSM–5 Service Software Instructions PAMS Technical Documentation GSM Activation Alt, P, B, G Status Bar Text Set phone to GSM band. PCN Page 26 Activation Status Bar Text Alt, P, B, P Set phone to PCN (GSM1800) band.
PAMS Technical Documentation NSM–5 Service Software Instructions Tuning The tuning menu offers functions for ME adjustments. RX Filter Calibration... command Activation Status Bar Text Alt, T, M Open RX Measurements dialog box Starts RX Filter Calibration tuning for the phone. Dialog mode: Modal RX Measurements dialog has the following items: Select Function listbox: Shows list of automatic selections. When selection is made values are loaded from phone. Value group: This group has several items.
NSM–5 Service Software Instructions PAMS Technical Documentation Save button: This saves values to the phone. Close button: This button closes the dialog without saving anything. Help button: This button opens help.
PAMS Technical Documentation NSM–5 Service Software Instructions RX Calibration... command Activation Status Bar Text Alt, T, R Open RX Calibration dialog box Starts RX calibration. The next automatic selections are made when this tuning function is activated: • Phone is set to local mode • Update RF information window The measurement is started automatically when RX calibration is entered. The measurement is done in five steps: 1.
NSM–5 Service Software Instructions PAMS Technical Documentation Dialog mode: modal RX Calibration dialog has the following items: AFC information box: Shows AFC init value, AFC slope and PSW slope values. AGC List box (ALT+A): AGC, DAC, Voltage. Repeat button (ALT+R): Measurement can be started again by pressing this button. Save button (ALT+S): Dialog is closed and tuning is saved to phone. Cancel button (ESC): Dialog is closed and tuning is not saved to phone.
PAMS Technical Documentation NSM–5 Service Software Instructions RX AM Suppression... command Activation Status Bar Text Alt, T, M, A Open RX Measurements dialog box Starts RX AM Suppression tuning for the phone. Dialog mode: Modal RX Measurements dialog has the following items: Select Function listbox: Shows list of automatic selections. When selection is made values are loaded from phone. Value group: This group has several items.
NSM–5 Service Software Instructions PAMS Technical Documentation Save button: This saves the values to the phone. NOTE: After GSM Suppression the same tuning must be made for the PCN band also! To change the band go to Product Menu and select Band, PCN. Close button: This button closes the dialog withour saving anything. Help button: This button opens help.
PAMS Technical Documentation NSM–5 Service Software Instructions Tx Power... command Activation Status Bar Text Alt, T, X Open TX Power Tuning dialog box Starts TX power tuning. When user has PKD–1 dongle in place tuning is started automatically with EEPROM values. Tuning values are loaded from program’s internal memory.
NSM–5 Service Software Instructions PAMS Technical Documentation GSM1800 TX Power Tuning dialog: Dialog mode: modal TX Power Tuning dialog has following items: Level, Coefficient and Targets list box (ALT+L): The power is presented in GSM or PCN values. The base power is selected automatically when the dialog is opened. The test value is not saved to the EEPROM.
PAMS Technical Documentation NSM–5 Service Software Instructions If this box is checked the base level is calculated. Base offset edit box: This edit box shows the base offset value that user can change. The base level calculation check box must be checked before this value is used. After this value is changed user must do the calculation. NOTE: Do not use Enter–button to accept this value. +/– buttons (+/– and left/right cursor keys): + and – buttons will cause power changing by 0.25dB steps.
NSM–5 Service Software Instructions PAMS Technical Documentation Tx I/Q... command Activation Status Bar Text Alt, T,Q Open TX I/Q Tuning dialog box This function is used for tuning TX I and Q branch DC offset, amplitude difference and phase difference. If user has PKD–1 dongle and other than NSM–X phone, then tuning is started automatically with EEPROM values. When using other dongles this selection opens same Start Tuning dialog as with TX Power Tuning.
PAMS Technical Documentation NSM–5 Service Software Instructions Tune Amplitude Difference scroll bar (ALT+A): When this selection is made user can increase or decrease the amplitude difference within 0.1 dB steps. The value range is –1...1. Tune Phase Difference scroll bar (ALT+P): When this selection is made user can increase or decrease the phase difference within 0.5° steps. The current phase difference is shown on the tuning window with numbers and bar figure. The value range is 85...95.
NSM–5 Service Software Instructions PAMS Technical Documentation Energy Management Calibration... command Activation Status Bar Text Alt, T,E Calibrate Battery Voltage This function is for battery a/d and charge current tunings. NOTE: This Calibration must be done when N100, N101 or a discrete component affecting these two is changed. Before battery a/d tuning is started a voltage setting request is shown to user (Set supply voltage to 10,5 V). Service Battery is in this case JBU–6.
PAMS Technical Documentation NSM–5 Service Software Instructions Settings group box: Contains EM calibration setting checkboxes: 1. Run battery & charger default values checkbox (ALT+1): Runs battery & charger default values to phone when selected 2. Battery voltage checkbox (ALT+2): Calibrates battery voltage A/D value. 3. Charger voltage checkbox (ALT+3): Calibrates charge voltage A/D value. 4. Battery size checkbox (ALT+4): Calibrates battery size A/D value. 5.
NSM–5 Service Software Instructions PAMS Technical Documentation Testing The Testing sub menu offers functions for ME testing. RF Controls... command Activation Status Bar Text Alt, E,R Open RF Controls dialog box This function is used for RF testing. Command opens RF Controls dialog, which contains data for testing and adjustments.
PAMS Technical Documentation NSM–5 Service Software Instructions When TX is selected, the next functions are made: Data transmission is activated If operation mode is continuous, – Operation mode is set to burst RF Information window is updated Continuous mode radio button is disabled. Note! Function is activated immediately, Apply is not needed.
NSM–5 Service Software Instructions PAMS Technical Documentation Channel edit box (ALT+H): User can enter here channel number that is used for both transmission and receiving. The frequency of the selected channel is shown after selection. Monitoring Channel edit box (ALT+M): This field selects neighbour monitoring channel. The frequency of the selected channel is shown after selection.
PAMS Technical Documentation NSM–5 Service Software Instructions Continuous Mode Channel: Greyed Channel: Updated OPERATION MODE = CONT.
NSM–5 Service Software Instructions PAMS Technical Documentation RSSI Reading... command Activation Status Bar Text Alt, E,R Read continuously RSSI value Command opens RSSI Reading dialog: Dialog mode: modal RSSI value is read continuously until user presses ESC–key or Close button to cancel reading. RSSI Reading dialog has following items: Close (ENTER) button: Closes the RSSI Reading dialog. Does not send anything to phone. Help button: Context sensitive help.
PAMS Technical Documentation NSM–5 Service Software Instructions Self Tests... command Activation Status Bar Text Alt, E,S Open MCU Self–tests dialog box Command is used for reading self test results and running self tests. When the selection is made, the test result is read from ME. The test result will be shown to the user within MCU Self–test dialog.
NSM–5 Service Software Instructions PAMS Technical Documentation message window is shown. If no response is received to power off test message in a few seconds, the user is informed by special info window, where user is asked to turn the power on and then press the return key. Note also that power–off test (if passed) turns power off and power should be reconnected by using the phones keypad after the successful test.
PAMS Technical Documentation NSM–5 Service Software Instructions I EEPROM Sec Checksum................ J PPM Validity.................... K Warranty State.................... L SW Version....................
NSM–5 Service Software Instructions PAMS Technical Documentation ADC Readings... command Activation Status Bar Text Alt, E,A Open ADC Readings dialog box. Command is used to read and show A/D values from phone. Command opens ADC Readings dialog. Dialog mode: modal ADC Readings dialog has static text field where measurements are updated to window every one second. ADC Readings dialog has following items: Close (ENTER) button: Closes the ADC Readings dialog. Does not send anything to phone.
PAMS Technical Documentation NSM–5 Service Software Instructions Audio... command Activation Status Bar Text Alt, E,U Opens a submenu which contains following options: Internal Audio Loops Activation Status Bar Text Alt, E,U,I Open Internal Audio loops dialog box. Command is used for making internal audio loop tests in Internal Audio Loops dialog.
NSM–5 Service Software Instructions PAMS Technical Documentation Turns buzzer off. Internal Audio Loop group: Input group: Next two different values can be selected for input: Internal radio button (ALT+I): Turns internal input. External radio button (ALT+I): Turns external input. Headset radio button (ALT+A): Turns headset input. Note: If Output is not Headset, loop is turned off. Output group: Next two different values can be selected for output: Internal radio button (ALT+T): Turns internal output.
PAMS Technical Documentation NSM–5 Service Software Instructions User Interface... command Activation Status Bar Text Alt, E,U Open User Interface Tests dialog box Command is used for making display tests in Display Tests dialog. Dialog mode: modal Display Tests dialog has following items: 1. Test Pattern radio button (ALT+1): In test display 1 all indicators are displayed and the display is filled with chessboard letters. 2.
NSM–5 Service Software Instructions PAMS Technical Documentation Test (ENTER) button: Starts IR Test. Close button: Closes the IR Test dialog. Vibra Test... command Activation Status Bar Text Alt, E, V Vibrator module test This command is used for testing phone’s or battery’s vibrator. Function opens Vibra Test dialog: Dialog mode: modal Vibra Test dialog has following items: Vibra Value box: Edit box where you can enter value from 0 to 255. Test (ENTER) button: Starts Vibra Test.
PAMS Technical Documentation NSM–5 Service Software Instructions Software Product Profile... command Activation Status Bar Text Alt, S,P Open Product Profile settings dialog box. Function is used for making product profile settings. When command is activated the product profile information is read from EEPROM and Product Profile dialog is opened. Dialog mode: modal Product Profile dialog has following items: Settings list box (ALT+E): A list where user can select desired setting.
NSM–5 Service Software Instructions PAMS Technical Documentation Start Up Self–tests... command Activation Status Bar Text Alt, S,S Open MCU start Up self–tests dialog box. Function is used for changing the state of the EEPROM selectable tests in MCU Start Up Self–tests dialog. Dialog mode: modal MCU Start Up Self–tests dialog has following items: Tests list box (ALT+T): When dialog is opened, the previous values will be read from the MCU EEPROM and shown on the list box.
PAMS Technical Documentation NSM–5 Service Software Instructions Set Factory Values... command Activation Status Bar Text Alt, S,V Set factory values With this selection user can set factory defaults to phone. This selection opens Default Factory values dialog. Dialog mode: modal Default Factory Values dialog has following items: Settings list box: Contains the selectable factory values. Set button: Sets the selected factory value to phone.
NSM–5 Service Software Instructions PAMS Technical Documentation Phone Identity... command Activation Status Bar Text Alt, S,I Open Phone Identity dialog box for editing Function is used to edit phone identity. NOTE: product code cannot be changed with this dialog, if product code is invalid, e.g. after EEPROM change, change product code first with Production Data Edit.
PAMS Technical Documentation NSM–5 Service Software Instructions User Name edit box (ALT+U): Field where user can enter user identification. IMEI edit box (ALT+I): Field where user can enter IMEI value. Field can contain up to 40 digits.This field is automatically filled, if ME is connected to the PC when dialog is loaded. Product Code edit box (ALT+P): Field where user can enter Product Code value. This field is automatically filled, if ME is connected to the PC when dialog is loaded.
NSM–5 Service Software Instructions PAMS Technical Documentation Input entries for FAX check box (ALT+F): When checked all fields become editable to allow user to enter values by hand e.g. from FAX. Close button (ESC): Cancels all edits and does not save values to phone. Help button Opens a help text. Write button (ALT+W): Writes programming data to phone. Actions are selected with Action Selection radio button. Read button (ALT+R): Reads identification data from phone and shows it in dialog controls.
PAMS Technical Documentation NSM–5 Service Software Instructions Warranty State... command Activation Status Bar Text Alt, S,W Open Warranty State dialog box This command is used to set the warranty state of a phone. When selected application opens Warranty State dialog box. Dialog mode: modal Warranty State dialog has the following items: State static text: USE For nomal phones. DEFECTIVE For phones which are being swapped. A warranty and other information is transferred to the working phone.
NSM–5 Service Software Instructions PAMS Technical Documentation Production Data Edit... command Activation Status Bar Text Alt, S,P Open Production Data Edit dialog box This command is used for programming HW version and other production data to phone. Only fields that are editable are validated and written to phone. Function opens the following Production Data Edit dialog box. Dialog mode: modal Production Data dialog has the following items: Production Code edit box: User can edit production code.
PAMS Technical Documentation NSM–5 Service Software Instructions Dealer The dealer sub menu offers functions for ME settings for dealers. User Settings... command Activation Status Bar Text Alt, D,U Open User Setting dialog box This command is used to edit some user settings. When this command is selected user is asked to read settings from the phone. After answering that dialog following User Settings and Values dialog is displayed. NOTE: This is a screen example.
NSM–5 Service Software Instructions PAMS Technical Documentation User can load user settings from file. Edit... button (ALT+D): Start Windows Paintbrush to edit loaded or saved graphical Wake up message. This picture is not available, if phone does not support WUG. OK button (ENTER): Writes user settings to phone. Cancel button (ESC): Closes the dialog box Short Code Memory... command Activation Status Bar Text Alt, S,C Open Edit SCM dialog box.
PAMS Technical Documentation NSM–5 Service Software Instructions Edit the Name. Number edit box (ALT+N): Edit the Number. Group edit box: Edit the Group number. SCM list box (ALT+C): List for available names and numbers. Write MS / Write SIM button (ALT+W): Write SCM values to phone or SIM and checks the validity of names and numbers. Read MS / Read SIM button (ALT+R): Read SCM values from phone or SIM. Save File...
NSM–5 Service Software Instructions PAMS Technical Documentation SCM & User Settings... command Activation Status Bar Text Alt, D,M Open SCM & User settings dialog box. This command is used to get SCM and user settings from phone to file and vice versa. Following information is loaded/saved with this dialog: all user settings, graphical/text wake up message, SCM, alarms, calendar items and CLI logos and groups. Only values of supported features are saved or loaded.
PAMS Technical Documentation NSM–5 Service Software Instructions Restore User Defaults... command Activation Status Bar Text Alt, D,R Open Restore Default User Settings. This command is used to restore Default User Settings, if they have degenerated. Dialog may be opened from menu, or is opened automatically, when loading or saving user settings fails or is skipped during flashing (see Flash Phone... command). The dialog is also opened after full factory set.
NSM–5 Service Software Instructions PAMS Technical Documentation enabled according to settings available in selected Market Area. Graphical Welcome Message check box (ALT+G): When checked user selects to restore default graphical welcome message. CLI Logos check box (ALT+C): When checked user selects to restore default CLI logos. Product Profiles check box (ALT+P): When checked user selects to restore default product profiles.
PAMS Technical Documentation NSM–5 Service Software Instructions Operators Settings... command Activation Status Bar Text Alt, D,O Open Operator Settings dialog. This command is used to set operator settings This selection opens following Operator Settinngs dialog. Dialog mode: modal Operator Settings dialog box has following items: Settings group: Country Code edit box (ALT+C): User can edit country code (3 or 4 digits). Network Code edit box (ALT+N): User can edit network code (2 digits).
NSM–5 Service Software Instructions PAMS Technical Documentation IWR Swap... command Activation Status Bar Text Alt, D,I Open IWR Swap dialog. This command is used to swap serial numbers of two phones. This selection opens following IWR Swap dialog.
PAMS Technical Documentation NSM–5 Service Software Instructions Flash Phone... command Activation Status Bar Text Alt, D,F Open Flash Phone dialog box. This command is used for flashing new software into the phone. When flashing dead phone, user may be asked to select phone type. If more than one phone is flashed without closing dialog, then user must press Check button after phone has been changed. Selection opens the following Flash Phone dialog box.
NSM–5 Service Software Instructions PAMS Technical Documentation MCU Image File group: Edit field (read only): Displays path of image file to be flashed. … button: Opens Open File dialog, with which user can select an image file to be flashed to ME. If user selects OK button, the name of selected file is copied to Flash Image edit field. Usually you should use Market Area list box to select Image file. PPM group: Edit field (read only): Displays path of PPM package file to be flashed.
PAMS Technical Documentation NSM–5 Service Software Instructions fields are not valid, then check box is disabled. Checkbox state is read from flash pack ini–file, from entry EraseDefinedArea. Low limit edit box (read only): Hexadecimal value defining low erase limit, value should be plain hexadecimal without any prefix. Field value is read from flash pack ini–file, from entry LowEraseLimit.
NSM–5 Service Software Instructions PAMS Technical Documentation NOTE: This is a screen sample, actual information may differ. Dialog mode: modal. Phone Type Selection dialog has following items: Phone Type group: List box: User can select phone type. OK button (ENTER): User accepts selected phone type. Cancel button (ESC): Phone type selection is cancelled and operation is aborted. ROM Version dialog NOTE: This is a screen sample, actual information may differ.
PAMS Technical Documentation NSM–5 Service Software Instructions View Quick/RF Info... command Activation Status Bar Text Alt, V,Q View Quick/RF information. If phone is in normal mode following Quick Info is shown: Dialog mode: modeless If phone is in local mode following RF Information is shown. Information is shown in a modeless dialog which may be left open during other operations. It is also updated when ever needed. Dialog mode: modeless Selections show what data is currently updated by PC.
NSM–5 Service Software Instructions PAMS Technical Documentation Phone Information... command Activation Status Bar Text Alt, V,P View Phone Identity. Command opens Phone Identity Information dialog, which shows identification information. Information is shown in a modeless dialog which may be left open during other operations. It is also updated when ever needed. Dialog mode: modeless Initialization file The After Sales Software has an initialisation file which has extension .INI.
PAMS Technical Documentation NSM–5 Service Software Instructions Channel (Channel=) Monitoring Channel 1 (MonitoringChannel=) AGC dB value (AGC=) AGC Absolute Value (AGCAbsolute=) Front End (FrontEnd=) Call Simulation dialog Monitoring Channel 2 (Monitoring Channel 2 =) Monitoring Channel 3 (Monitoring Channel 3 =) Monitoring Channel 4 (Monitoring Channel 4 =) Monitoring Channel 5 (Monitoring Channel 5 =) Monitoring Channel 6 (Monitoring Channel 6 =) All selections and parameters which are not same as in
NSM–5 Service Software Instructions PAMS Technical Documentation Tuning Instructions General All tuning operations are carried out using the service software. The service software turns the phone into the locals mode, in which the phone can be outwardly controlled via the MBUS interface. Tuning is based on the software communicating with the D/A and A/D converters of the phone. In some instances the phone processor will also calculate the required correction parameter.
PAMS Technical Documentation NSM–5 Service Software Instructions Required Equipment – PC with service software; see separate section for instructions on installation and use. – Service accessories; see equipment setup pictures. – Multimeter or DVM.
NSM–5 Service Software Instructions PAMS Technical Documentation Equipment Setup for Testing DC Unit 6. 5. 2. 7. 1. 3. 4. Page 78 Item: Service accessory: Product code: 1 Service Box JBU–6 0770153 2 RF Adapter RAF–5 for JBU–6 0775302 3 DC Power Cable PCS–1 0730012 4 Service MBUS Cable DAU–9S 0730108 5 DC–DC Cable SCB–3 0730114 6 Software protection key PKD–1 0750018 7 Service SW diskette 3.5” for WinTesla Service SW diskette 3.
NSM–5 Service Software Instructions PAMS Technical Documentation Flash Concept with JBU–6 11. 13. 14. 10. 12. 10. 1. 9A. 6. 7. 9B. 5. 8. 2. 3. 4.
NSM–5 Service Software Instructions PAMS Technical Documentation Testing Without Covers – Using Test–frame MJS–9 6. Spectrum Analyzer 7. 1. 4. 2. 5. 3.
NSM–5 Service Software Instructions PAMS Technical Documentation Flashing With FLA–10 9. 11. 12. 10. 8. 1. 7A. 8. 5. 13. 7B. 6. 2. 14. 8. 3. 4.
NSM–5 Service Software Instructions PAMS Technical Documentation POS Flash Concept with FLA–10 4. 5. 3. 2. 1. Item: Service accessory: Product code: 1 Flash Loading Adapter FLA–10 0081346 2 Service Cable XCS–1 0730218 3 Travel Charger ACP–8 ACP–8C 0675211 ACP–8K 0273111 ACP–8E 0272169 China plug 90–264 Vac Korea plug 90–264 Vac DIN plug (E&A) 90–264 Vac Page 82 4 FLS–4 POS Reflashing Tool 6 Service SW diskette 3.5” for WinTesla Service SW diskette 3.
NSM–5 Service Software Instructions PAMS Technical Documentation JBU–6 RF Measurement Concept DC Unit Spectrum Analyzer 5. 6. 2. 3. 1. 4. Item: Service accessory: Product code: 1 Service Box JBU–6 0770153 2 RF Cable XRS–3 0730184 3 DC Power Cable PCS–1 0730012 4 Service MBUS Cable DAU–9S 0730108 5 Software protection key PKD–1 0750018 6 Service SW diskette 3.5” for WinTesla Service SW diskette 3.
NSM–5 Service Software Instructions PAMS Technical Documentation Warranty Transfer DC 3. 2. 1. 3. 1.
PAMS Technical Documentation NSM–5 Service Software Instructions Tuning Steps IMPORTANT: It is recommended to use adapter RAF–5 with JBU–6 when the phone is tuned because of the galvanic (direct) connection to the phone. 1. RX Filter Calibration BB–filter tuning is fully internal operation. External signal generators etc. are not needed, only command for phone to execute filter calibration procedure. NOTE: RX Filter Calibration is needed when N505 has been changed. 2.
NSM–5 Service Software Instructions PAMS Technical Documentation 2. Measurement with high input level is executed 3. User is requested to put signal generator to low input level (read from .INI file). 4. Measurement with low input level is executed 5. The RX Calibration dialog will be updated when previous steps are done.
NSM–5 Service Software Instructions PAMS Technical Documentation Software reports the following: AFC init value AFC slope PSW slope Gain step values Limits for the reported values If everything went well the reported values should approximately be the following: Parameter Low limit High limit AFC init value –200 200 AFC slope 135 345 PSW slope For information Gain step values EGSM (nominal) PCN (nominal) 0 37 28 1 47 38 2 57 48 3 62 53 4 72 63 5 82 73 Issue 1 02/2002 Nok
NSM–5 Service Software Instructions Gain step values PAMS Technical Documentation EGSM (nominal) PCN (nominal) 6 92 83 7 102 93 8 112 103 Troubleshooting If the calibration does not succeed the software normally reports ”Unable to read data from phone” or ”Failed to set high reference” or ”Failed to set low reference”. In this case check first the basic functionality of the receiver chain: RF generator frequency set as in the calibration and level for example to the high reference value.
PAMS Technical Documentation NSM–5 Service Software Instructions 3. AM suppression tuning This operation is recommended when RX components have been changed (between N505/Hagar and Z670/antenna switch). AM suppression calibration is for tuning four Hagar parameters to get as small RSSI value as possible. For AM–suppression calibration external signal generator with AM–modulation is needed. Select Am Suppression... from Tuning menu. Signal generator setup: AM–modulation, fmod = 1 kHz, mod.
NSM–5 Service Software Instructions PAMS Technical Documentation Test limits for AM–calibr. results: –86 dBm (EGSM) –95 dBm (PCN) Press Save button to save the values. NOTE: AM suppression calibration is needed for the PCN band as well. To change the band go to Product Menu and select Band, PCN.
PAMS Technical Documentation NSM–5 Service Software Instructions 4. Alignment of Transmitter Power Levels Equipment: Pulsed power meter or spectrum analyzer and 10 dB attenuator. Voltage source set to 3.6 V. The following settings for the spectrum analyzer are recommended when aligning the power levels: zero span, resolution and video bandwidths 1 MHz, input attenuation 40 dB, sweep time 1 ms, video triggering.
NSM–5 Service Software Instructions PAMS Technical Documentation GSM1800 TX Power Tuning dialog: It is recommended that all the power levels are separately aligned although there is a possibility to align only three and calculate the rest. This is due to the calculation method.
NSM–5 Service Software Instructions PAMS Technical Documentation 5. I/Q Modulator Alignments I/Q modulator alignments has to performed in both bands. See chapter ”Service Software Instructions” and section ”TX I/Q... command” for further information. –67.71 kHz D.C. offset tunings: Set this value to minimum CHF +67.71 kHz > 30 dB > 35 dB Amplitude & phase difference: Set this value to minimum Procedure: Connect the spectrum analyzer to the phone antenna connector.
NSM–5 Service Software Instructions PAMS Technical Documentation The level of the centre frequency CHF should be at least 30 dB down to the wanted sideband CHF - 67.71 kHz. The level of the unwanted sideband CHF + 67.71 kHz should be at least 35 dB down to the wanted sideband CHF - 67.71 kHz. 6. Energy Management Calibration See section ”Tuning – Energy Management Calibration... command” for further information.
PAMS Technical Documentation NSM–5 Service Software Instructions Appendix 1, Vocabulary Abreviation Description ASIC Custom circuit which for instance controls communication between MCU and DSP JBU–6 Service box CLF Common Look and Feel CLI Calling Line Identification COBBA Common Base Band Analog DATA DATA interface module DAU–9S/P MBUS/FBUS cable DLL Dynamic Link Library DSP Digital Signal Processor which controls radio interface and speech coding/decoding EEPROM Memory for adjustme
NSM–5 Service Software Instructions Page 96 PAMS Technical Documentation PC IBM PS/AT or compatible personal computer PCI Phone Controlling Interface SW for PC PKD–1/1NS/1CS Hardware protection key (DESKEY DK2) for protecting service software from illegal copying.
