Nokia Customer Care NPL-4/5 Series Transceivers Service Software Instructions Issue 1 05/04 Copyright ©2004 Nokia Corporation. All rights reserved.
NPL-4/5 Company confidential Service Software Instructions Nokia Customer Care [This page left intentionally blank] Page 2 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care Table of Contents Page No Service Software ...................................................................................................................................... 5 Overview ................................................................................................................................................. 5 Phoenix ....................................................................................................................
NPL-4/5 Company confidential Nokia Customer Care Preparations for Phoenix ..................................................................................................................60 Compensation of cable and jig losses....................................................................................... 60 GPIB interface.................................................................................................................................. 61 Automatic tuning procedure .................
Company confidential NPL-4/5 Nokia Customer Care Service Software Overview The following steps will be required to use service software with NPL-4/5. • Install Phoenix Service Software. • Install data package for NPL-4/5 for your region. • FPS-8 flash update. • JBV-1 docking station SW update. Phoenix Phoenix is the new generation service software for reprogramming, testing and tuning the phone. It has been designed to meet the challenges in servicing modern cellular phone technology.
NPL-4/5 Company confidential Nokia Customer Care Download and read the release notes which have useful information on the software version you are using. • Download the latest data packages for the products you will be using. • Before you start installing the program, check that the dongle is attached to the parallel port. Contact your supervisor in order to obtain a suitable dongle. Administrator rights are required in order to be able to install Phoenix.
Company confidential NPL-4/5 Nokia Customer Care • Make sure that the dongle is attached. • Go to the Control Panel and select Add/Remove Programs. • Select Phoenix Service software Axx 200x.xx.x.xx. • Click Change/Remove then OK to remove the application. You may have to reboot your PC after uninstallation. Data packages The product data package contains all product specific data to make the Phoenix Service Software and tools usable with a certain phone model.
NPL-4/5 Company confidential Nokia Customer Care Data Package for Phoenix (Product Specific) Before installation Product Data Package contains all product specific data to make the Phoenix Service Software and tools usable with a certain phone model. It also includes the latest version of flash update package for FLS-4* and FPS-8*/FPS-8C • Check that the Dongle is attached to the parallel port of your computer. • Install Phoenix Service SW • Download the installation package (e.g. NPL-4/5_dp_1.00.
Company confidential NPL-4/5 Nokia Customer Care Installation of Phoenix data package (product specific) Run the NPL-4/5_dp_v_1.00.exe to start installation. When you choose “Next” the files needed for installation will be extracted. Please wait… Choose “Next” to continue. Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved.
NPL-4/5 Company confidential Nokia Customer Care From this view you can see the contents of the Data Package. Read the text carefully. There should be information about the Phoenix version needed with this data package. Choose “Next”. Page 10 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care Install Shield checks where the Phoenix application is installed and the directory is shown. Choose “Next” to continue. Confirm location and choose “Next” to continue. Phone model specific files will be installed. Please wait. Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved.
NPL-4/5 Company confidential Nokia Customer Care Choose “Finish” to complete installation. You now have all phone model specific files installed in your Phoenix Service SW. Page 12 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care How to uninstall data package Uninstallation can also be done manually from Windows Control Panel / Add / Remove Programs/ “NPL-4/5 Phone Data Package”. If you try to install the same version of Phoenix Data Package that you already have, you are asked if you want to uninstall the version you have on your PC. Answer “OK” to uninstall, “Cancel” if you don’t want to uninstall. Older versions of data packages do not need to be uninstalled.
NPL-4/5 Company confidential Nokia Customer Care How to Manage Connections Start Phoenix Service SW and Login. Choose “Manage Connections” From “File” – Menu Existing connections can be selected, edited, deleted and new ones created by using this dialog. A connection can be created either manually or by using a Connection Wizard. To add new connection, choose “Add” and select if you want to create it manually or by using the Wizard. Page 14 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care Choose “Next” to continue.
NPL-4/5 Company confidential Nokia Customer Care If you use the Wizard, connect the tools and a phone to your PC and the wizard will automatically try to configure the correct connection. Activate the connection you want to use by clicking it and use up/down arrows to move it on top of the list. Choose “Apply”. The connection is now selected and can be used after closing the “Manage Connections” window. Selected connection will be shown on the right hand bottom corner of the screen.
Company confidential NPL-4/5 Nokia Customer Care When the Product is found, Phoenix will load product support and when everything is ready, name of the loaded product support module and its version will be shown on the bottom of the screen. Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved.
NPL-4/5 Company confidential Nokia Customer Care [This page left intentionally blank] Page 18 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care How to Update Flash Support Files for FPS-8*/FPS-8C and FLS-4* Before installation • Install Phoenix Service SW and Phoenix data package. • Install the phone model Specific Datapackage for Phoenix • The flash support files are delivered in the same installation package with Phoenix data package. • Normally it is enough to install the data package only before updating the FPS8.
NPL-4/5 Company confidential Nokia Customer Care Choose “Next” to continue installation It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia\Phoenix. Choose “Next” to continue. You may choose another location by selecting “Browse” (not recommended). Page 20 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care Installation continues… Choose “Finish” to complete procedure. • FLS-4 can be used right after Flash Update Package is installed. • FPS-8*/FPS-8C must be updated by using Phoenix! Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved..
NPL-4/5 Company confidential Nokia Customer Care How to update the FPS-8*/FPS-8C Flash Prommer SW Start Phoenix Service Software Select”FPS-8 / FPS-8*/FPS-8C maintenance” from”Flashing” menu. When new FPS-8 flash update package is installed to computer you will be asked to update the files to your FPS-8 Prommer. Select ”Yes” to update files.. 0 02 Update procedure takes a couple of minutes. Page 22 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care FPS-8 SW can also be updated by pressing ”Update” button and selecting appropriate fps8upd.ini file under C:\Program Files\Nokia\Phoenix\Flash - directory All files can be loaded separately to FPS-8. To do this, just press right mouse button in “Flash box files” window and select file type to be loaded. More information and help can be found from the “Help” dialog. Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved..
NPL-4/5 Company confidential Nokia Customer Care FPS-8 Activation and Deactivation • Before the FPS-8 can be successfully used for phone programming, it must be first activated. • If there is a need to send FPS-8 box to somewhere e.g. for repair, box must be first deactivated. Activation Before FPS-8 can be successfully used for phone programming, it must be first activated. Fill in first “FPS-8 activation request” sheet, in the FPS-8 sales package and follow the instructions in the sheet.
Company confidential NPL-4/5 Nokia Customer Care The activation file you saved to C:\ProgramFiles\Nokia\Phoenix\BoxActivation - directory will be shown (e.g. 00000.in), check that it is correct. Box will be activated when you choose “Open” Turn FPS-8 power off and on to complete activation Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved..
NPL-4/5 Company confidential Nokia Customer Care Deactivation Start Phoenix Service Software. Select ”FPS-8 / FPS-8*/FPS-8C maintenance” from ”Flashing” menu Select “Deactivate” from the “FPS8/8C Maintenance” – UI. Confirm Deactivation by choosing “Yes”, Box will be deactivated. Turn FPS-8 power off and on to complete deactivation. Page 26 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care JBV-1 Docking Station SW The JBV-1 Docking Station is a common tool for all DCT-4 generation products. In order to make the JBV-1 usable with different phone models, a phone specific Docking Station Adapter is used for different service functions. The JBV-1 Docking Station contains Software (Firmware) which can be updated.
NPL-4/5 Company confidential Nokia Customer Care Installing SW needed for the JBV-1 SW update Note: DO NOT CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER YET! Run Jbv1_update.zip file and start SW Installation by double clicking Setup.exe. Files needed for JBV-1 Package Setup Program will be extracted. Installation begins, please read the information shown and Choose “Next” to continue. Page 28 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care Use suggested destination folder where JBV-1 SW Package will be installed and choose “Next” to continue. Select “Full” Installation and choose “Next” to continue Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved..
NPL-4/5 Company confidential Nokia Customer Care Program Folder will be created. Choose “Next” to continue, Software files will be installed. After successful installation, choose “Finish” to complete. NOW YOU CAN CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER! Page 30 Copyright © 2004 Nokia Corporation. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care Connect power to JBV-1 (11-16V DC) from external power supply, then connect USB Cable between JBV-1 USB connector and PC. Windows will detect connected USB cable and detect drivers for new HW. Follow the instructions and allow Windows to search and install the best drivers available. After this procedure the actual JBV-1 SW update can begin. Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved..
NPL-4/5 Company confidential Nokia Customer Care Updating the JBV-1 docking station software Go to folder C:\Program Files\Nokia\ JBV-1 SW Package\ FIRMWARE UPDATE and start JBV-1 Update SW by double clicking fwup.exe. JBV-1 Firmware update starts and shows current status of the JBV-1 connected. If firmware version read from your JBV-1 is not the latest one available, it needs to be updated by choosing “Update Firmware”. Choose file JBV1v11.
Company confidential NPL-4/5 Nokia Customer Care software of your JBV-1 docking station and it is ready for use. Issue 1 05/04 Copyright © 2004 Nokia Corporation. All rights reserved..
NPL-4/5 Company confidential Nokia Customer Care [This page left intentionally blank]. Page 34 Copyright © 2004 Nokia Corporation. All rights reserved.
NPL-4/5 Nokia Customer Care RF-tunings: Quick Guide for Tuning With Phoenix General remarks RF tunings must be performed in the same order as shown in this document. The order of the corresponding menu items in the Phoenix Service SW may be different. If baseband tunings are needed, they should be completed before the RF tunings Screen shots described in this document may change as the service software is developed.
NPL-4/5 Nokia Customer Care Service Tool Concept for RF Tuning Operations General instructions for tuning: Connect the phone to a PC, which has Phoenix Service Software and a dongle installed, using either • Repair jig and DAU-9S (RS232) cable or • DAU-9T cable (RS232) or • DKU-5 cable (USB) Connect the phone to a power supply (DC voltage of 4.0V, min. current of 3A) and switch the phone on. - Start Phoenix Service Software and open FBUS connection.
NPL-4/5 Nokia Customer Care Figure 1: RF Tuning Setup Figure 2: RF tuning setup Item: Type: Service accessory: Product code: 1 MJ-9 Module jig 0770707 2 PCS-1 DC power cable 0730012 3 XRF-1 RF antenna cable 0730085 4 DAU-9S OR Service Mbus cable 0730138 DAU-9T OR Service Mbus cable xxxxxxxx DKU-5 Service Mbus cable xxxxxxxx PKD-1 Software protection key 0750018 Phoenix Service SW 8409031 Phoenix Service SW 0774286 5 10 11 CD-ROM RF Tuning after repairs Following tunings h
NPL-4/5 Nokia Customer Care additionally required. • In general repairs in the RX front-end always require RX Calibration and Rx Band Filter Calibration for all three bands. • Repairs in the PLL circuit always require RX Calibration of the low band. If the RF ASIC was replaced all calibrations mentioned above have to be done.
NPL-4/5 Nokia Customer Care Figure 3: RX Calibration Setup - Press “Start”: The current calibration values are loaded from the phone memory and displayed in the window “PM values” and a window pops up, instructing you on frequency and power level tuning of the RF signal generator: 1 ) Power Level: -60 dBm 2 ) Frequency: 881.667110 MHz (GSM 850) or 942.467110 MHz (GSM 900) - Compensate for external RF cable and test jig losses.
NPL-4/5 Nokia Customer Care Figure 4: Calibration Values Page 40 Copyright © 2004 Nokia Corporation. All rights reserved.
NPL-4/5 Nokia Customer Care The results must fulfil the following limits: Table 1: Calibration Values Calibration value / Test case Typical Low limit High limit AFC value / check AFC_VALUE [DAC] 53 -350 +350 AFC Slope / check AFC_SLOPE [DAC] 128 90 165 Rssi 0 / Check RX GSM xxx Gain A 1 [dB] 65 59 71 Rssi 2 / Check RX GSM xxx Gain A 3 [dB] 77 71 83 Note! GSM xxx means the selected band: GSM 850 / 900 / 1800 / 1900 Rx calibration GSM1800 and GSM1900 Both bands are available in all variant
NPL-4/5 Nokia Customer Care The setup should now look like this (GSM1800): Figure 5: Calibration Mode A window pops up, instructing you on frequency and power level tuning of RF signal generator: 1) Power Level: -60 dBm 2) Frequency: 1842.867110 MHz (GSM 1800) - Compensate for external RF cable and test jig losses. If a radio communication tester (CMD55, CMU200, HP 8960, MT8801) is used, assure that “continuous mode” is switched on and “modulation” switched off.
NPL-4/5 Nokia Customer Care A typical result will look like this: Figure 6: Calibration Execution The setup should now look like this (GSM1900) Figure 7: Calibration Execution A window pops up, instructing you on frequency and power level tuning of RF signal generator: Issue 1 05/04 Copyright ©2004 Nokia Corporation. All rights reserved..
NPL-4/5 Nokia Customer Care 1) Power Level: -60 dBm 2) Frequency: 1960.067110 MHz (GSM 1800) - Compensate for external RF cable and test jig losses. If a radio communication tester (CMD55, CMU200, HP 8960, MT8801) is used, assure that “continuous mode” is switched on and “modulation” switched off. - Press “OK” and the calibration will be executed. - Press “OK” to finish RX calibration.
NPL-4/5 Nokia Customer Care Rx band filter response GSM850 The GSM850 chapters apply only for NPL-4 (US- variant). Manual Tuning: Open the window “Rx Band Filter Response Compensation” in Phoenix Service Software as follows: - Select → Tuning (Alt-U) - Select → Rx Band Filter Response Compensation (Alt-C) The necessary band selection is made by Phoenix automatically in the low band.
NPL-4/5 Nokia Customer Care Compensate for external RF cable and test jig losses. - Adjust the “Input signal Level (dBm)” field to -60 [dBm] on the “Rx Band Filter Response Compensation” window. - Set the RF source as indicated in the pop- up window: 1 ) Power Level: -60 dBm 2 ) Frequency: 867.267710 MHz - Press “OK”.
NPL-4/5 Nokia Customer Care • Externally controlled by a PC and a SW-program, e.g. HP Vee: Rx_AGC+Bandfilter_Cal.vee. Open the window “Rx Band Filter Response Compensation” in Phoenix Service Software as follows: - Select → Tuning (Alt-U) - Select → Rx Band Filter Response Compensation (Alt-C) The necessary band selection is made by Phoenix automatically in the low band. -Select automatic in the in the “Rx Band Filter Response Compensation” window.
NPL-4/5 Nokia Customer Care - Connect the RF signal generator to the antenna port of the test jig respectively the phone. - Compensate for external RF cable and test jig losses. - Press “OK”. - Press “Save and continue” to tune GSM1800 and GSM1900. Limits The typical value of the “Measured Level Difference (dB)” on channel 37 (middle of band) shall be approximately 0 dB.
NPL-4/5 Nokia Customer Care - Set operating mode to local mode. → Tuning (Alt-U) - Select → Rx Channel Select Filter Calibration (Alt-H) - Select The setup should now look like this: Figure 13: Channel Filter Calibration - Press “Tune” and the optimal values are found. - Press “Stop”, the values are saved to the phone and the calibration has finished.
NPL-4/5 Nokia Customer Care Notch / check rx baseband filter NOTCH _ [DAC] 21 -6 +37 TX power level tuning NPL-4 and NPL-5 support GMSK and EDGE mode for the Power amplifier. Therefore the Power level tuning must be carried out for both modes in each band.It is strongly recommended to use Phoenix Autotune capability. The functionality of Phoenix Autotune is described in chapter Fully automatic Calibration, Tuning & Measurement by Phoenix. Nevertheless manual tuning is described below.
NPL-4/5 Nokia Customer Care Figure 14: TX Power Level Tuning -Select->TX Data Type->Random Adjust DAC Values in TX PA mode ‘High’ for bold power levels according to target values: Table 4: GSM850, GSM900 Power level Target power Power level Target power 5 32.
NPL-4/5 Nokia Customer Care 0 29.5 dBm 9 12 dBm 1 28 dBm 10 10 dBm 2 26 dBm 11 8 dBm 3 24 dBm 12 6 dBm 4 22 dBm 13 4 dBm 5 20 dBm 14 2 dBm 6 18 dBm 15 0 dBm 7 16 dBm Base -30 dBm 8 14 dBm The power levels may differ from the target power levels mentioned in Phoenix. Make sure that the output power for maximum Power Level is equal or lower than 1dB below the saturation output power.
NPL-4/5 Nokia Customer Care The setup should now look like this: Figure 16: TX Power Level Tuning - Select “TX data type” and then “Random” - Press “OK” to tune - Press “Save and continue” to tune GSM1800 and GSM1900 - Finish TX power level tuning closing the tuning window when all bands are tuned (also in EDGE mode).
NPL-4/5 Nokia Customer Care 12 19 dBm 13 17 dBm 14 15 dBm 15 13 dBm Base -15 dBm Table 7: EGPRS1800, EGPRS1900 Power level Target power Power level Target power 2 26 dBm 10 10 dBm 3 24 dBm 11 8 dBm 4 22 dBm 12 6 dBm 5 20 dBm 13 4 dBm 6 18 dBm 14 2 dBm 7 16 dBm 15 0 dBm 8 14 dBm Base -15 dBm 9 12 dBm The power levels may differ from the target power levels mentioned in Phoenix.
NPL-4/5 Nokia Customer Care Wait until the TX/IQ window is popped up: Figure 17: TX IQ Tuning - Select “TX data type” and then “All 1”. Connect a Spectrum Analyzer or GSM tester with the option “Narrow Spectrum” to the antenna pads of the phone. If a spectrum analyzer is used, make the following settings, adjust “Center frequency” and “Markers” according to bands. GSM900 Issue 1 05/04 Center Frequency 897.
NPL-4/5 Nokia Customer Care Marker 2 897.4 MHz Marker 3 897.46771 MHz The Spectrum Analyzer now shows a diagram like this: Figure 18: Spectrum Analyser The purpose of this alignment is to tune the carrier signal (at marker 2) and the +67kHz signal (at marker 3) to a minimum level. Use the variables “TX I DC offset” and “TX Q DC offset” to adjust the carrier signal to a minimum level (marker 2). Tuning can be performed by using arrow keys on the keyboard.
NPL-4/5 Nokia Customer Care Figure 19: Spectrum Analyser Use the variables “Amplitude difference” and “Phase difference” to adjust the +67kHz signal to a minimum level (Marker 3). Tuning can be performed by using the arrow keys on the keyboard. Pushing the sliders by using the mouse is less sensitive however possible. After tuning to the minimum the level difference between marker 3 and the peak level at marker 1 must exceed 40dB.
NPL-4/5 Nokia Customer Care Figure 20: Spectrum Analyser Compare the results in the TX IQ Tuning Window with the limits below: Table 8: Limit Values Value Typical Limit min. Limit max. TX I DC offset 0 -6 6 TX Q DC offset 0 -6 6 Amplitude difference 0 -1 1 Phase difference 90 80 100 The setup should now look like this: Page 58 Copyright © 2004 Nokia Corporation. All rights reserved.
NPL-4/5 Nokia Customer Care Figure 21: TX IQ Tuning - Press “Save and continue” to tune GSM850 in EDGE mode -Continue until all bands are tuned, also in EDGE mode. Note: The optimum values for “TX I and Q Offset” and “Amplitude and Phase Difference” vary from phone to phone Issue 1 05/04 Copyright ©2004 Nokia Corporation. All rights reserved..
NPL-4/5 Nokia Customer Care Fully Automatic Calibration, Tuning & Measurement by Phoenix “Auto-Tune” Auto-tune is designed to align the phone' s RF part easier and faster, it calibrates, tunes and measures the following for NPL-4 and NPL-5: • Rx channel select filter calibration • Rx calibration • RX band filter response compensation • RX Dtos balance calibration • Rx AM suppression • Tx power level tuning • Tx I/Q tuning and saves the results in a log-file, if wanted Preparations for Phoeni
NPL-4/5 Nokia Customer Care The discrete frequencies for loss determinations are defined in the Phoenix software. To change attenuation values in Settloss table PKD-1NS dongle is needed. GPIB interface The GPIB card is labeled by National Instruments or at least compatible with their products. Drivers must be installed and card by Phoenix. The following procedure has to be made once for “acceptance”: -Select->Tools (Alt-T) Options (Alt-O) GPIB card (Alt-G) The window “GPIB Card” pops up.
NPL-4/5 Nokia Customer Care Automatic tuning procedure -Select Tuning (Alt-U) Auto-Tune (Alt-A) Tune (Alt-T) Log file To enable the creation of a log file to save the calibration, tuning and measurement results edit the command of the file as follows: Row 8: Logging 1 Additional the path for the logging file can be defined in row 9. Delete the character <;> at the beginning of the row to enable the command.
NPL-4/5 Nokia Customer Care Service Tool Concept For Baseband Tuning Operations EM calibrations should be carried out in JBV-1 Docking Station equipped with MJF-27 Docking Station Adapter. Note: RF tunings must be carried out in MJ-9 module jig. MJF-27-Docking Station Adapter can only be used for RF testing purposes. Power to JBV-1 should be supplied from an extarnal DC power supply, not FPS-8 prommer.
NPL-4/5 Nokia Customer Care Service concept for NPL-4/5 baseband tunings and RF testing 7 Note! No RF tuning allowed with RF coupler! Item Accessory type Service Accessory Product code 1 JBV-1 Docking Station 0770298 2 DA-7 Docking adapter 0770708 3 SCB-3 DC-DC Cable 0730114 OR CA-5S 4 XRF-1 RF antenna cable 0730085 5 PCS-1 DC power cable 0730012 6 DAU-9S Service MBUS cable 0730108 7 PKD-1 Software protection key 0750018 Phoenix service SW 8409031 Phoenix service SW 07
NPL-4/5 Nokia Customer Care Baseband Tuning operations Energy management tuning External power supply needed. EM Calibration is used for calibrating Battery and Charger settings of the phone. Preparation for EM Calibration: - Connect DC Cable SCB-3 between JBV-1 and Vin of Phone for Charger calibration - Connect 12…15 V from Power Supply to JBV-1 - NOTE! Check that connection is F-BUS (does not work with M-BUS!) Select Maintenance->Tuning-> Energy Management Calibration.
NPL-4/5 Nokia Customer Care Select “Calibrate” to run the selected calibrations. Limits for Energy Management Calibration: Parameter Min.
Company confidential NPL-4/5 Nokia Customer Care Flashing Setup Instructions POS (Point of Sales) flash concept Figure 23: POS flash Item Type Description Code 1 SF-6 POS Flash Adapter 0770709 2 XCS-1 service cable 0730218 3 ACP-12 AC Charger 0675*** 4 FLS-4S POS flash dongle, for E/A area 0080541 FLS-4S POS flash dongle, for APAC area 0080542 SW Phoenix Sales Package xxxxxxx 5 Issue 1 05/04 Copyright ©2004 Nokia Corporation. All rights reserved.
NPL-4/5 Company confidential Nokia Customer Care Module jig concept Note! For RF tuning and testing. Figure 24: Module jig concept Page 68 Item Type Description Code 1 MJ-9 Module jig 0770707 2 PCS-1 DC power cable 0730012 3 XRF-1 RF antenna cable 0730085 4 DAU-9S Service MBUS cable 0730108 5 PKD-1 Software protection key 0750018 6 SW Phoenix Sales Package xxxxxxx Copyright ©Nokia. All rights reserved.
Company confidential NPL-4/5 Nokia Customer Care JBV-1 flash concept Note! Instead of JBV-1 + DA-7, flashing can be performed with MJ-9 Module jig. Figure 25: JBV-1 Flash concept Item Type Description Code 1 JBV-1 Docking station 0770298 2 DA-7 Docking adapter 0770708 3 PCS-1 DC power cable 0730012 4 XCS-4 Modular cable 0730178 5 FPS-8 Flash prommer box 0080321 6 Printer cable incl. in FPS-8 sales pack 0730029 7 AXS-4 D9 – D9 cable, incl.
NPL-4/5 Company confidential Nokia Customer Care JBV-1 Service concept Note! For RF testing and BB tuning. No RF tuning allowed.
Company confidential NPL-4/5 Nokia Customer Care Parallel flash concept Figure 27: Parallel flash concept Item Type Description Code 1 DA-7 Docking adapter 0770708 2 JBV-1 Docking station 0770298 3 XCS-4 Modular cable 0730178 4 PCS-1 DC power cable 0730012 7 AXS-4 D9 – D9 cable, incl. in FPS-8*/FPS-8C sales pack 0730090 8 Printer cable Incl.
NPL-4/5 Company confidential Nokia Customer Care [This page left intentionally blank] Page 72 Copyright ©Nokia. All rights reserved.
