CCS Technical Documentation RH-9 Series Transceivers Service Tools Issue 1 11/02 ãNokia Corporation
RH-9 Service Tools CCS Technical Documentation Table of Contents JBV-1 Docking Station and MJF-16 Adapter .............................................................4 Product Code ............................................................................................................. 4 MJS-37 Module Jig ......................................................................................................6 Product Code .................................................................................
RH-9 Service Tools CCS Technical Documentation List of Figures Page No Fig 1 View of JBV-1............................................................................................................4 Fig 2 View of JBV-1 and MJF-16 together .........................................................................5 Fig 3 View of JBV-1, MJF-16 and the transceiver RH-9 ....................................................5 Fig 4 View of MJS-37 ...................................................................
RH-9 Service Tools CCS Technical Documentation JBV-1 Docking Station and MJF-16 Adapter The JBV-1 Docking Station has been designed for calibration and software update use. The MJF-16 Docking Station Adapter makes signal connections to the phone. JBV-1 and MJF-16 are used as one unit.
RH-9 Service Tools CCS Technical Documentation Figure 2: View of JBV-1 and MJF-16 together Figure 3: View of JBV-1, MJF-16 and the transceiver RH-9 Issue 1 11/02 ãNokia Corporation Page 5
RH-9 Service Tools CCS Technical Documentation MJS-37 Module Jig The MJS-37 Module Jig is used for testing of UI/system/RF-module*. Product Code MJS-37 Module Jig: 0770282 Figure 4: View of MJS-37 Note: The nominal supply voltage for MJS-37 is 8-12VDC. If the input-voltage exceeds 12VDC, the MJS-37 jig may be damaged. By default the MJS-37 supplies the phone with 4.1VDC. If other output voltages are needed (e.g.
RH-9 Service Tools CCS Technical Documentation MJS-67 Soldering Jig The Soldering Jig MJS-67 is used for soldering and as a rework jig for system module.
RH-9 Service Tools CCS Technical Documentation GAC-4 RF Adapter The RF adapter GAC-4 is used for enabling RF connection. To be attached after A-cover is removed.
RH-9 Service Tools CCS Technical Documentation FPS-8 Flash Prommer (Sales Pack) The Flash Prommer FPS-8 is used with e.g. FLA-23, JBV-1 and MJS-37. Power is supplied to FPS-8 from the Universal Power Supply.
RH-9 Service Tools CCS Technical Documentation FPS-8C Parallel Flash Prommer (Sales Pack) The Parallel Flash Prommer FPS-8C is used with MJF-16 and JBV-1. Flash programming can be done to maximum of 8 phones parallel. FPS-8C consists of eight SF11C programming cards. SF11C card is functionally identical to FPS-8.
RH-9 Service Tools CCS Technical Documentation ACF-8 Universal Power Supply ACF-8 Universal Power Supply is used to power FPS-8. ACF-8 has 6 V DC and 2.1 A output.
RH-9 Service Tools CCS Technical Documentation RH-9 FLA-23 POS (Point Of Sale) Flash Loading Adapter The POS Flash Loading Adapter FLA-23 is used in place of the phone's normal battery during service, to supply a controlled operating voltage, and is also used for flashing.
RH-9 Service Tools CCS Technical Documentation FLC-2 DC Cable The FLC-2 is used to supply a controlled operating voltage.
RH-9 Service Tools CCS Technical Documentation AXS-4 Service Cable The AXS-4 D9-D9 Service Cable is used to connect two 9 pin D connectors e.g. between PC and FPS-8. Cable length is 2 meters.
RH-9 Service Tools CCS Technical Documentation XCS-1 Service Cable The XCS-1 Service Cable is used to connect FLS-4S to FLA-23.
RH-9 Service Tools CCS Technical Documentation SW Security Device PKD-1 SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC. Without the dongle present it is not possible to use the service software. Printer or any such device can be connected to the PC through the dongle if needed.
RH-9 Service Tools CCS Technical Documentation FLS-4S POS (Point Of Sale) Flash Device (Sales Pack) FLS-4S is a dongle and flash device incorporated into one package, developed specifically for POS use.
RH-9 Service Tools CCS Technical Documentation PCS-1 Power Cable The PCS-1 Power Cable (DC) is used to connect, for example, JBV-1 to FPS-8.
RH-9 Service Tools CCS Technical Documentation DAU-9S MBUS Cable The MBUS Cable DAU-9S has a modular connector, and is used with between PC's serial port and, for example, the Module Jig MJS-37.
RH-9 Service Tools CCS Technical Documentation SCB-3 DC Cable The DC Cable SCB-3 is used to connect, for example, the JBV-1 to the phone.
RH-9 Service Tools CCS Technical Documentation XCS-4 Modular Cable XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing and service purposes.
RH-9 Service Tools CCS Technical Documentation Printer Cable This cable is used to connect the PC to FPS-8.
