CCS Technical Documentation NEM-2 Series Transceivers Service Software Instructions Issue 1 07/03 Copyright Nokia. All rights reserved.
NEM-2 Company confidential Service Software Instructions CCS Technical Documentation [This page left intentionally blank] Page 2 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Quick Guide for Phoenix Service SW Installation ........................................................ 3 Phoenix Installation Steps in Brief ..............................................................................3 Phoenix Service SW....................................................................................................... 4 Before Installation ........................................................................................
NEM-2 Company confidential CCS Technical Documentation JBV-1 Service Concept ..............................................................................................82 Parallel Flash concept ................................................................................................83 Page 2 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Quick Guide for Phoenix Service SW Installation Phoenix Installation Steps in Brief DCT-4 generation Test and Service Software is called “Phoenix” These are the basic steps to install the Phoenix • Install the Phoenix Service SW • Install the Data Package for Phoenix (product specific data and flash update package) • Manage connection settings (depends on the tools you are using) • Update FPS-8 SW (if you use FPS-8) • Activate FPS-8 • Upd
NEM-2 Company confidential CCS Technical Documentation Phoenix Service SW Before Installation • Check that a Dongle is attached to the parallel port of your computer. • Download the installation package (e.g. phoenix_service_sw_a3_03_83_005.exe) to your computer (e.g. C:\TEMP) • Close all other programs • Run the application file (e.g. phoenix_service_sw_a3_03_83_005.
Company confidential NEM-2 CCS Technical Documentation Startup Run the phoenix_service_sw_a3_03_83_005.exe to start installation. When you choose “Next” the files needed for installation will be extracted. Kindly wait. If the setup files are already extracted (left in the file system from previous installation) following dialog appears. Always click "Yes to All" to overwrite the existing setup files. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Dongle Driver Installation and Version Check If there is no previously installed Dongle driver, installation will take place... If the Dongle driver is installed and it is older than the latest supported version, the latest version will be installed when you choose “Yes”. The latest version is always included in the latest Phoenix installation package. PC needs to be rebooted before installation can continue. Click "Yes" to reboot the PC.
Company confidential NEM-2 CCS Technical Documentation First Time Installation of Phoenix After Dongle driver installation / update (if needed) installation continues from this step. Click "Next" in Welcome dialog to continue. Choose the destination folder, it is recommended to use the default folder C:\ProgramFiles\Nokia\Phoenix. Choose “Next” to continue. You may choose another location by selecting “Browse” (not recommended) Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Setup copies the components, please wait. Progress of the setup is shown. Please wait… If restarting of your computer is needed the Install Shield Wizard will tell you about it. Select "Yes..." to reboot the PC immediatelly and "No..." to reboot the PC manually. Note that Phoenix doesn't work, if components are not registered. Click "Finish" to continue. Page 8 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation After the reboot components are registered and Phoenix is ready for use. If reboot is not needed components are registered after copying them. If restarting of your computer is not needed, Click "Finish" to exit the setup. Phoenix is now ready for use.
NEM-2 Company confidential CCS Technical Documentation Update Installation of Phoenix If you already have the Phoenix Service SW installed on your computer, sooner or later there will be need to update it when new versions are released. Please note that very often the Phoenix Service SW and the Phone Specific Data Package for Phoenix come in pairs, meaning that certain version of Phoenix can only be used with certain version of Data Package. Always use the latest available versions of both.
Company confidential NEM-2 CCS Technical Documentation How to Uninstall Phoenix Uninstallation can be done manually from Windows Control Panel - Add / Remove Programs. Choose “Phoenix Service Software” and click "Add/Remove". Choose “OK” to uninstall Progress of the uninstallation is shown. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation You may have to reboot the PC after uninstallation. If restarting is not needed, the following dialog will appear: Note! If you have different product packages installed, components are uninstalled only if they are not included in other product packages. Page 12 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Data Package for Phoenix (Product Specific) Before installation Product Data Package contains all product specific data to make the Phoenix Service Software and tools usable with a certain phone model. It also includes the latest version of flash update package for FLS-4* and FPS-8* • Check that the Dongle is attached to the parallel port of your computer. • Install Phoenix Service SW • Download the installation package (e.g. nem-2_dp_1.00.
NEM-2 Company confidential CCS Technical Documentation Installation of Phoenix Data Package (Product Specific) Run the nem-2_dp_v_1.00.exe to start installation. When you choose “Next” the files needed for installation will be extracted. Please wait Choose “Next” to continue. Page 14 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation From this view you can see the contents of the Data Package. Read the text carefully. There should be information about the Phoenix version needed with this data package. Choose “Next”. Confirm location and choose “Next” to continue. Install Shield checks where the Phoenix application is installed and the directory isshown. Choose “Next” to continue. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Phone model specific files will be installed... please wait. Choose “Finish” to complete installation. You now have all phone model specific files installed in your Phoenix Service SW. Page 16 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation How to Uninstall Data Package Uninstallation can also be done manually from Windows Control Panel / Add / Remove Programs/ “NEM-2 Phone Data Package”. If you try to install the same version of Phoenix Data Package that you already have, you are asked if you want to uninstall the version you have on your PC. Answer “OK” to uninstall, “Cancel” if you don’t want to uninstall. Older versions of data packages do not need to be uninstalled.
NEM-2 Company confidential CCS Technical Documentation How to Manage Connections Start Phoenix Service SW and Login. Choose “Manage Connections” From “File” – Menu Existing connections can be selected, edited, deleted and new ones created by using this dialog. A connection can be created either manually or by using a Connection Wizard. To add new connection, choose “Add” and select if you want to create it manually or by using the Wizard. Choose “Next” to continue. Page 18 Copyright Nokia.
Company confidential NEM-2 CCS Technical Documentation In the next dialogs you will be asked to select some settings for the connection Manual Settings A) For FLS-4S POS Flash Device choose following connection settings Media: FBUS COM Port: Virtual COM Port used by FLS-4 Please check this always! (To check please go to Windows / Control Panel / FLS Virtual Port / Configuration) B) For FPS-8 Flash Prommer choose following connection settings: Media: FPS-8 Port Num: COM Port where FPS-8 is connected COMBO
NEM-2 Company confidential CCS Technical Documentation Activate the connection you want to use by clicking it and use up/down arrows to move it on top of the list. Choose “Apply”. The connection is now selected and can be used after closing the “Manage Connections” window. Selected connection will be shown on the right hand bottom corner of the screen. To use the selected connection, connect the phone to Phoenix with correct service tools, make sure that it is switched on and select “Scan Product”.
Company confidential NEM-2 CCS Technical Documentation How to Update Flash Support Files for FPS-8* and FLS-4* Before Installation • Install Phoenix Service SW and Phoenix data package. • Install the phone model Specific Datapackage for Phoenix • The flash support files are delivered in the same installation package with Phoenix data package. • Normally it is enough to install the data package only before updating the FPS8.
NEM-2 Company confidential CCS Technical Documentation Choose “Next” to continue installation It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia\Phoenix. Choose “Next” to continue. You may choose another location by selecting “Browse” (not recommended). Page 22 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Installation continues… Choose “Finish” to complete procedure. • FLS-4 can be used right after Flash Update Package is installed. • FPS-8* must be updated by using Phoenix! Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation How to Update The FPS-8* Flash Prommer SW Start Phoenix Service Software Select”FPS-8 / FPS-8C maintenance” from”Flashing” menu. When new FPS-8 flash update package is installed to computer you will be asked to update the files to your FPS-8 Prommer. Select”Yes” to update files.. 0 02 Update procedure takes a couple of minutes. Page 24 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation FPS-8 sw can also be updated by pressing”Update” button and selecting appropriate fps8upd.ini file under C:\Program Files\Nokia\Phoenix\Flash - directory All files can be loaded separately to FPS-8. To do this, just press right mouse button in Flash box files” window and select file type to be loaded. More information and help can be found from the “Help” dialog. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation FPS-8 Activation and Deactivation • Before the FPS-8 can be successfully used for phone programming, it must be first activated. • If there is a need to send FPS-8 box to somewhere e.g. for repair, box must be first deactivated. Activation Before FPS-8 can be successfully used for phone programming, it must be first activated. Fill in first “FPS-8 activation request” sheet, in the FPS-8 sales package and follow the instructions in the sheet.
Company confidential NEM-2 CCS Technical Documentation The activation file you saved to C:\ProgramFiles\Nokia\Phoenix\BoxActivation - directory will be shown (e.g. 00000.in), check that it is correct. Box will be activated when you choose “Open” Turn FPS-8 power off and on to complete activation Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Deactivation Start Phoenix Service Software. Select ”FPS-8 / FPS-8C maintenance” from ”Flashing” menu Select “Deactivate” from the “FPS8/8C Maintenance” – UI. Confirm Deactivation by choosing “Yes”, Box will be deactivated. Turn FPS-8 power off and on to complete deactivation Page 28 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation JBV-1 Docking Station SW The JBV-1 Docking Station is a common tool for all DCT-4 generation products. In order to make the JBV-1 usable with different phone models, a phone specific Docking Station Adapter is used for different service functions. The JBV-1 Docking Station contains Software (Firmware) which can be updated.
NEM-2 Company confidential CCS Technical Documentation Installing SW Needed for the JBV-1 SW Update Note: DO NOT CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER YET! Run Jbv1_update.zip file and start SW Installation by double clicking Setup.exe. Files needed for JBV-1 Package setup Program will be extracted. Installation begins, please read the information shown and Choose “Next” to continue.
Company confidential NEM-2 CCS Technical Documentation “Next” to continue. Select “Full” Installation and choose “Next” to continue Program Folder will be created. Choose “Next” to continue, Software files will be Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation installed. After successful installation, choose “Finish” to complete. NOW YOU CAN CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER! Connect power to JBV-1 (11-16V DC) from external power supply, then connect USB Page 32 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Cable between JBV-1 USB connector and PC. Windows will detect connected USB cable and detect drivers for new HW. Follow the instructions and allow Windows to search and install the best drivers available. After this procedure the actual JBV-1 SW update can begin. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Updating the JBV-1 Docking Station Software Go to folder C:\Program Files\Nokia\ JBV-1 SW Package\ FIRMWARE UPDATE and start JBV-1 Update SW by double clicking fwup.exe. JBV-1 Firmware update starts and shows current status of the JBV-1 connected. If firmware version read from your JBV-1 is not the latest one available, it needs to be updated by choosing “Update Firmware”. Choose file JBV1v11.
Company confidential NEM-2 CCS Technical Documentation software of your JBV-1 docking station and it is ready for use. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation FPS-8/FLS-4S USB driver installation for NEM-X 1. Connect the phone to the FPS8/FLS-4S and to the USB port and switch it on. NOTICE: If you connect a NEM-X without a MMC card to the PC for the first time, a “USB device“ is installed with an error. Ignore this error and press the “Finish” button to close the window. 2. Start Phoenix and initiate the product scan. 3. Select Flashing -> FPS8 Flash. Now the correct Flash window should open.
Company confidential NEM-2 CCS Technical Documentation 4. Press the button “Flash” to start flashing. 5. After a few seconds a windows "Found New Hardware" should popup. It installs the first driver (Nokia ADSP device) automatically. 6. During flashing a second "Found New Hardware" should popup. It installs the second USB driver (Nokia NEM-X) automatically. 7. Because the USB enumeration takes some time, this flashing sequence could end with a ADSP timeout error. In this case restart flashing.
NEM-2 Company confidential CCS Technical Documentation FPS-8C USB driver installation for NEM-X If you will flash for the first time, you have to do the USB setup before. Else the USB flashing won't be working! NOTICE: To flash files, which added file sizes are together more than 7MB (e.g. NEM-1 V2.30 or higher), your FPS8C card must have 16MB RAM for successful flashing! 1. Start Phoenix V2003.11.1.9 or newer 2. Select the product: File -> Choose Product -> NEM-1 or NEM-2 3.
Company confidential NEM-2 CCS Technical Documentation 5. Start Usb Port Setup: Options -> "USB Port Setup" 6. The following window is shown: 7. The setup could be done with one phone, which is plugged from the first to the last FPS8C port and USB port. Please mark the USB cable with e.g. it's number to make sure, that it belongs always to the same FPS8C card! Press OK and follow the instructions. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation 8. The following window is shown: 9. Depending on the used PC, the setup of one port could take 1 to 90 seconds. During USB port setup several "Found New Hardware" should pop up and the driver will be installed. If the port setup succeeded, the next port will be displayed. This sequence repeats until all 8 ports are configured. If an error occured, the complete setup has to be repeated. 10.
Company confidential NEM-2 CCS Technical Documentation [This page left intentionally blank] Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Page 42 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Receiver tuning: Quick Guide for Tuning With Phoenix General remarks RF tuning steps must be performed in the same order as shown in this document. The order of the corresponding menu items in the Phoenix Service SW may be different. If baseband tuning is needed, it must be completed before the RF tunings Avoid unnecessary tuning – factory-tuning values are always the most accurate ones.
NEM-2 Company confidential CCS Technical Documentation Service Tool Concept for RF Tuning Operations • RF tuning setup must be carried out with JXS-2 and DA-1. • Power to JBV-1 must be supplied from an external DC power supply, not FPS8 prommer • JBV-1 input voltage: Nominal input for RF tuning is +3.9 V DC • Remember the cable attenuation when setting required RF levels • DA-1 losses must be taken from the DA-1 label Note! JBV-1 Docking Station stays outside the box.
Company confidential NEM-2 CCS Technical Documentation Item: Type: Service accessory: Product code: 2 DA-1 Docking station adapter 0774288 3 JXS-2 Shield box 0770673 4 XRS-6 RF cable SMA to N-connector 0730231 5 PCS-1 Power cable for JBV-1 0730012 6 SMA to SMA RF cable 6 PKD-1NS SW protection key 7 PKD-1CS SW protection key 9 Issue 1 07/03 Phoenix service SW Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Automated RF tunings for NEM-2 The recommended tuning of NEM-2 is autotuning. Autotuning as well as all RF tunings must be performed via DA-1 inside JXS-2. The losses for DA-1 RF coupler can be taken from the DA-1 label. Losses for the RF cables must be added in the “set loss” function of Phoenix. Autotuning Autotune feature is designed to align product’s RF part easier and faster. By this autotune component product is tuned automatically.
Company confidential NEM-2 CCS Technical Documentation The Autotune component can be found under Tuning menu: Environment: Hardware requirements: PC with Windows 98/2000/NT Power supply Product specific module jig RF-splitter and -cables RF equipment (only one of each is needed) Tx: Agilent E4406 (VSA series transmitter tester) Agilent E4445 (PSA series transmitter tester) Rohde&Schwarz, FSE-family of Signal Analyzers Rohde&Schwarz, FSIQ-family of Signal Analyzers Rx: Agilent ESG family of RF Signal Gene
NEM-2 Company confidential CCS Technical Documentation GPIB addresses are not defined. Component finds the addresses and uses them automatically. If several TX tuning devices are connected via GPIB bus, this component uses Agilent (VSA or PSA). In RX side, Agilent has highest priority. Protection Components are protected by PKD-1CS, PKD-1NS, PKD-1 and PKD-1P dongles using standard TSS protection procedure.
Company confidential NEM-2 CCS Technical Documentation Press “Tune” to start the tuning. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Receiver Tuning: RX Channel Select Filter Calibration Extra equipment / external RF signal not needed. Must be done before other RX calibrations. This function is used to calibrate RX channel select filter in GSM Phones. Rx Channel select filter is tuned only in one band = Single calibration for both bands. Select Tuning => Rx Channel select filter calibration.
Company confidential NEM-2 CCS Technical Documentation RX Calibration RF generator needed. This tuning performs RX Calibration. Must be done separately on each band! Calibration is automatically performed first at GSM850 and then at GSM1900 band. If tuning is successfull, tuning continues in the next band. AFC tuning is done while GSM850 band RX Calibration is performed. Remember to take jig and cable attenuations into account! Select Tuning => Rx calibration Press “Start" to start tuning.
NEM-2 Company confidential CCS Technical Documentation Set RF generator to required GSM850 frequency => OK Set RF generator to required frequency => OK Tuning values and ADC readings are shown.
Company confidential NEM-2 CCS Technical Documentation Tuning values and ADC readings are shown.
NEM-2 Company confidential CCS Technical Documentation RX Band Filter Response Compensation RF generator needed. This operation must be done separately on each band! Calibration is made automatically, starting with GSM850 and then with GSM1900..
Company confidential NEM-2 CCS Technical Documentation The tuning begins from GSM850 band and continues the same way for GSM1900 band Set the first required frequency and level => OK Set the 2nd required frequency and level => OK Set the 3rd required frequency and level => OK Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Set the 4th required frequency and level => OK Set the 5th required frequency and level => OK Set the 6th required frequency and level => OK Page 56 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Set the 7th required frequency and level => OK Set the the 8th required frequency and level => OK Set 9th required frequency and level => OK Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Typical values and limits in Rx Band Filter Response Compensation GSM850: Channel Input frequency (MHz) Typ. Low limit (dB) High limit (dB) 118 867.26771 -1.266 -10 3.5 128 869.26771 -0.641 -3.5 3.5 140 871.66771 -0.188 -3.5 3.5 172 878.06771 -0.094 -3.5 3.5 190 881.66771 -0.188 -1 1 217 887.06771 -0.391 -3.5 3.5 241 891.86771 -0.266 -3.5 3.5 251 893.86771 -0.359 -3.5 3.5 261 895.26771 -0.453 -10 3.
Company confidential NEM-2 CCS Technical Documentation Set the first required frequency and level => OK Set the 2nd required frequency and level => OK Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Set the 3rd required frequency and level => OK Set the 4th required frequency and level => OK Set the 5th required frequency and level => OK Page 60 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Set the 6th required frequency and level => OK Set the 7th required frequency and level => OK Set the 8th required frequency and level => OK Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Set the 9th required frequency and level => OK Page 62 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Typical values and limits in Rx Band Filter Response Compensation GSM1900: Channel Input frequency (MHz) Typ. Low limit (dB) High limit (dB) 495 1927.06771 -0.25 -10 3.5 512 1930.26771 0.73 -3.5 3.5 537 1935.26771 1.05 -3.5 3.5 585 1945.06771 0.74 -3.5 3.5 661 1960.06771 0.02 -1 1 736 1975.06771 0.65 -3.5 3.5 794 1986.66771 -0.52 -3.5 3.5 810 1989.86771 -1.07 -3.5 3.5 835 1994.86771 -1.45 -10 3.
NEM-2 Company confidential CCS Technical Documentation Press “Save and continue” to end the tuning process. The following message appears: Page 64 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Transmitter tuning TX Power Level Tuning Power Meter (or Spectrum analyzer) needed With Tx Power Level Tuning, the coefficients are adjusted for each power level Must be done separately on all bands! Start Power Level tuning at GSM850, then continue at GSM1900 band. In GSM850 and GSM1900 bands the power level tuning is made only for high PA mode.
NEM-2 Company confidential CCS Technical Documentation Select “Start”, tuning begins automatically from the GSM850 band Make the required adjustments of the spectrum analyzer as shown on the picture and press “OK”.. The coefficient table lists the power level, coefficient, target dBm and DAC value for each power level. The tuned power level can be chosen by using up and down arrows or mouse. Page 66 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation The current power level is shown with inverse colors. The tuning value can be adjusted with “-“ and “+” keys GSM850: Tune base level and power levels 19,15 and 5 to target level . Press “Save and Continue” to go to the next band. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation GSM1900: tune base level and power levels 15, 11 and 0 to target level. Change the adjustments of the spectrum analyzer as shown on the picture and press “OK”. Page 68 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Typical values: GSM850 Power level PA high mode 5 0.6- 0.9 7 - 15 0.2 - 0.25 19 0.13- 0.18 Base 0.1- 0.15 Adjust the power levels if needed by using the “-” and “+” keys. Typical values: GSM1900 Power level PA high mode 0 0.55- 0.75 11 0.2- 0.3 15 0.15 - 0.2 Base 0.1- 0.15 Adjust the power levels as with GSM850. Finally press “Save and Continue” to end the tuning process. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation TX I/Q Tuning Spectrum analyzer needed Tx IQ Tuning allows changing the Tx I DC Offset, Tx Q DC Offset, Amplitude difference and Phase difference Must be done separately on each band! Changing from 850 to 1900 is made automatically. Remember to take jig and cable attenuations into account! Select Tuning => Tx_IQTuning The tuning is done by setting each of the sliders to desired value. The sliders can be changed only when the tuning is ongoing.
Company confidential NEM-2 CCS Technical Documentation Tuning starts at the GSM850 band automatically when you press “Start” . Move the sliders to reach values within specified limits Make the required adjustments of the spectrum analyzer as shown in the picture: Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Press “Save and Continue” to go to the next band.. Make the required adjustments of the spectrum analyzer for GSM1900 as shown in the picture. Tune LO leak to minimum with TXI/TXQ DC offset control (f0 on spectrum analyzer screen) Tune wrong sideband to minimum using Amplitude/Phase difference controls (f0+68kHz Page 72 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation on spectrum analyzer screen) Choose “Save and Continue” to end tuning at the GSM850 band when values are within limits . Finally press “Save and Continue” to stop the tuning process. Issue 1 07/03 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Service Tool Concept For Baseband Tuning Operations EM calibrations should be carried out in JBV-1 Docking Station equipped with DA-1 Docking Station Adapter Note: RF tunings must be carried out in MJ-6 module jig, JBV-1 Docking Station Adapter can only be used for RF testing purposes Power to JBV-1 should be supplied from an external DC power supply, not FPS-8 prommer JBV-1 input voltages: • • Maximum + 16 VDC Nominal input for RF tunings is +12 V D
Company confidential NEM-2 CCS Technical Documentation Service Concept for NEM-2 Baseband tunings Item: Type: Service accessory: Product code: 1 JBV-1 Docking station 0770298 2 DA-1 Docking station adapter 0774288 3 CA-5S EM calibration cable for JBV-1 and R1011 0730283 4 XRS-6 RF cable SMA to N-connector 0730231 5 PCS-1 Power cable for JBV-1 0730012 6 DAU-9S MBUS cable 0730108 7 PKD-1 SW protection key 0750018 8 9 Issue 1 07/03 Phoenix Service SW DKU-2 Tomahawk to USB
NEM-2 Company confidential CCS Technical Documentation Baseband Tuning operations Energy Management Tuning External power supply needed. EM Calibration is used for calibrating Battery and Charger settings of the phone. Preparation for EM Calibration: - Connect DC Cable CA-5S between JBV-1 and Vin of Phone for Charger calibration. - Connect 12…15 V from Power Supply to JBV-1. - NOTE! Check that connection is F-BUS (does not work with M-BUS!). Select Maintenance => Tuning => Energy Management Calibration.
Company confidential NEM-2 CCS Technical Documentation Select “Calibrate” to run the selected calibrations. Limits for Energy Management Calibration: Parameter Min.
NEM-2 Company confidential CCS Technical Documentation LCD Contrast Tuning Extra equipment not needed This function is used to calibrate the LCD Contrast Must be done when LCD module is replaced and there is a considerable difference in the contrast! Select TEST mode if not already selected. Select Maintenance => Testing => Display Test Select Test =>Pattern test Select Test Pattern => Chess pattern Select Lights => Display Select => Send To Phone. Page 78 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Select Maintenance => Testing => Display Tune Press “Default” button and following default values will be set; “Contrast offset slider” is set to 0% (See picture below) “Contrast Factory offset” slider is set 41 Tune the Contrast by using “Contrast Factory offset” slider.. Close the “Display Tune” – dialog to end tuning. Check the contrast from the Phone UI.
NEM-2 Company confidential CCS Technical Documentation Page 80 Copyright Nokia. All rights reserved.
Company confidential NEM-2 CCS Technical Documentation Flashing Setup Instructions POS (Point of Sales) Flash Concept via FLS-4 Figure 1: POS flash Item Type Description Code FLA-36 Point Of Sales Flash loading adapter 0770467 2 XCS-1 Modular cable 0730218 3 ACF-8 Power supply incl. in 1) 0680032 4 FLS-4S PoS Flash dongle 0080543 Phoenix Service SW xxxxxxx Tomahawk USB cable 0730238 5 6 Issue 1 07/03 DKU-2 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation Module Jig Concept Figure 2: Module jig concept Note! No tuning with MJ-6! Item Type Description Code 1 MJ-6 Module repair jig 0770463 2 PCS-1 Power cable for MJ-6 0730012 3 XRS-6 RF cable SMA to N-connector 0730231 4 DAU-9S MBUS cable 0730108 5 PKD-1 Software protection dongle 0750018 6 n.a.
Company confidential NEM-2 CCS Technical Documentation Flash Concept via FPS-8 Figure 3: FPS-8 Flash concept Item Type Description Code 1 FLA-36 PoS Flash adapter for R1011 0770467 2 XCS-1 Service cable 0730218 3 XCS-4 Service cable 0730178 4 FPS-8 Flash Prommer 0080321 5 Incl. in 4) 6 Incl. in 4) 7 PKD-1 SW Protection key 0750018 8 Phoenix Service SW 9 Incl. in 4) 0680032 Tomahawk USB cable 0730238 10 Issue 1 07/03 DKU-2 Copyright Nokia. All rights reserved..
NEM-2 Company confidential CCS Technical Documentation JBV-1 Service Concept Figure 4: Service Concept Item: Type: Service accessory: Product code: 1 JBV-1 Docking station 0770298 2 DA-1 Docking station adapter 0774288 3 CA-5S EM calibration cable for JBV-1 and R1011 0730283 4 XRS-6 RF cable SMA to N-connector 0730231 5 PCS-1 Power cable for JBV-1 0730012 6 DAU-9S MBUS cable 0730108 7 PKD-1 SW protection key 0750018 8 9 Page 82 Phoenix Service SW DKU-2 Tomahawk to USB c
Company confidential NEM-2 CCS Technical Documentation Parallel Flash concept Figure 5: Parallel flash concept Item Type Description Code 1 JBV-1 Docking station 0770298 2 DA-1 Docking station adapter 0774288 3 XCS-4 Modular cable RJ45 0730178 4 PCS-1 Power cable for JBV-1 0730012 5 Serial cable 2X from 9) 6 Centronix cable from 9) SW Protection key 0750018 7 PKD-1 8 Phoenix Service SW 9 FPS-8C Parallel Flash Prommer incl.
NEM-2 Company confidential CCS Technical Documentation The reflash of more than 4 phones in parallel requires either: 2 separate 4-port USB Hubs conected to PC with USB 2.0 support or 2 separate USB PCI cards supporting USB 1.1 or USB 2.0 installed in the PC. Each of 2 4port USB Hubs must be connected to the different USB ports on PC side. [This page left intentionally blank] Page 84 Copyright Nokia. All rights reserved.
