PAMS Technical Documentation NSE–8/9 Series Transceivers Service Tools Issue 1 07/99
NSE–8/9 Service Tools PAMS Technical Documentation CONTENTS Page No Service Interface Cable TDS–7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Module Jig MJS–13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flash Loading Adapter FLA–5 (Sales Pack) . . . . . . . . . . . . . . . . . . . . . . Flash Prommer FPS–4S (Sales Pack) . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Box TDF–4 . . . . . . . . . . . . . . . . . . . . . . . . .
NSE–8/9 PAMS Technical Documentation Service Tools Service Interface Cable TDS–7 The Service interface cable is used to flash and tune the phone without disassembling it.
NSE–8/9 PAMS Technical Documentation Service Tools Module Jig MJS–13 The Module Jig MJS–13 is used for component level repair of the system module. Product Code Module Jig MJS–13: 0770158 View of MJS–13 Note: Page 4 The nominal supply voltagerange for MJS–13 is 9–15 V.
NSE–8/9 PAMS Technical Documentation Service Tools Flash Loading Adapter FLA–5 (Sales Pack) The Flash Loading Adapter FLA–5 is used with the Service Battery BBD–3 and Service Cable SCH–5. Power is supplied to FLA–5 from the Flash Security Box TDF–4 via the DC cable PCC–1B, (The PCC–1B cable can be replaced with a Travel Charger ACH–6), and is connected to the Flash Prommer FPS–4S with the cable AXS–5.
NSE–8/9 PAMS Service Tools Technical Documentation Flash Prommer FPS–4S (Sales Pack) The Flash Prommer FPS–4S is used to update the main software of the phone. Updating is done by first loading the new MCU software from the PC to the flash prommer, and then loading the new SW from the prommer to the phone. When updating more than one phone in succession, the MCU software only needs to be loaded to the prommer once.
NSE–8/9 PAMS Technical Documentation Service Tools Security Box TDF–4 The Security Box TDF–4 is required for updating MCU software, and infra red testing. Note1: TDF–4 is delivered in de–activated mode.
NSE–8/9 PAMS Service Tools Technical Documentation Service Audio Box JBA–4 The Service Audio Box JBA–4 is used between the module repair jig MJS–13 and audio test cables SCB–5 and ADS–1.
NSE–8/9 PAMS Technical Documentation Service Tools Modular Cable XMS–3 The modular cable is used to connect the TDS–7 or MJS–13 to the FLA–5 (or 7) flash loading adapter. This enables flashing of the phone. The XMS–3 is also used when flashing with the Point Of Sales (POS) device FLS–2.
NSE–8/9 PAMS Service Tools Technical Documentation Warranty Transfer Tool SCW–1 The Warranty Transfer Tool is used to connect two phones and enables transfer of user data (picture messages,T9 user dictionary etc.) from one phone to another. Two tools are required to perform Warranty Transfer. The tool is also used for the Point Of Sales (POS) flash device FLS–2.
NSE–8/9 PAMS Technical Documentation Service Tools Audio Cable ADS–1 Audio cable is an adapter routing AF signals (MIC/EAR) from an 8 pin modular connector to two BNC connectors.
NSE–8/9 PAMS Service Tools Technical Documentation D15–D15 Cable AXS–5 The D15–D15 Cable AXS–5 is used to connect two 15 pin D connectors. e.g. between FLA–5 and FPS–4S.
NSE–8/9 PAMS Technical Documentation Service Tools DC Cable PCC–1B The DC Cable PCC–1B is used e.g. to connect FLA–5 and TDF–4.
NSE–8/9 PAMS Technical Documentation Service Tools RF Coaxial Test Cable The RF Coaxial cable is used to connect the transceiver to external measuring equipment during servicing. Note: Typical attenuation at 900MHz is 0.9dB (with MJS–13 & TDS–7) Typical attenuation at 1800MHz is 1.
NSE–8/9 PAMS Technical Documentation Service Tools MBUS Cable DAU–9S The MBUS Cable DAU–9S has a modular connector, and is used for data communication with the phone for connecting TDS–7 and MJS–13 to a PC.
NSE–8/9 PAMS Technical Documentation Service Tools Audio Test Cable SCB–5 The Audio Test Cable is used to connect the phones headset to the Service Audio Box JBA–4, supplying Mic/Ear signals to external test devices.
NSE–8/9 PAMS Technical Documentation Service Tools Power Cable PCS–1 The Power Cable PCS–1 is used to connect the module jigs MJS–13 and service interface TDS–7 to an external power supply.
NSE–8/9 PAMS Technical Documentation Service Tools Modular T–adapter The modular T–adapter is a suitable branching unit to provide the needed parallel modular connections. Used for warranty transfer between two phones.
NSE–8/9 PAMS Technical Documentation Service Tools SW Security Device PKD–1 SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC. Whitout the dongle present it is not possible to use the service software. Printer or any such device can be connected to the PC through the dongle if needed.
NSE–8/9 PAMS Service Tools Technical Documentation Dongle/Flash Device FLS–1 /2 (Sales Pack) FLS–1/2 are dongle and flash devices incorporated into one package, developed specifically for POS use.
NSE–8/9 PAMS Technical Documentation Service Tools FLS–1 Connection Diagram with TDS–7 Note: TDS–7 required to flash with FLS–1 1.
NSE–8/9 Service Tools PAMS Technical Documentation [This page intentionally left blank] Page 22 Issue 1 07/99
