Nokia Customer Care RH-19/RH-50 Series Cellular Phones 4 - Service Tools Issue 3 05/2004 2004 Nokia Corporation.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care This page has been intentionally left blank Page 2 2004 Nokia Corporation.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools Table of Contents Page No Service Tools............................................................................................................................................... 5 List of service tools ..............................................................................................................................
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care This page has been intentionally left blank Page 4 2004 Nokia Corporation.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools Service Tools Note: Service tools used on the NPL-2 may also be used on the RH-19/RH-50. However, the latest version of the FLA-30, with small adaptions, is preferred for the RH-19/RH-50. List of service tools The table below gives a short overview of service tools that can be used for testing, error analysis and repair of product RH-19/RH-50, refer to various set-ups.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care JVB-1 docking station (product code: 0770298) with MJF-17 docking station adapter The JVB-1 docking station has been designed for calibration and software update use. The MJF-17 docking station adapter makes signal connections to the phone. JVB-1 and MJF-17 are used as one unit.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools View of MJF-17 CPL-10 antenna coupler (product code: 0770548) RF antenna coupler for use with MJF-17. Extends MJF-17 to allow RF function tests in GSM bands 850, 900, 1800 and 1900 MHz. Features include: • easy attachment to MJF-17 without use of tools • reliable RF connection to phone module under test • low attenuation and small “ripple” over the width of each GSM band View of CPL-10 Issue 3 05/2004 2004 Nokia Corporation.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care MJS-52 module repair jig (product code: 0770476) Repair jig for RH-19/RH-50 phone module that allows full phone function.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools Power supply features • jig and phone power supply via 3mm DC jack, fuse • power stabilization and voltage regulator on jig (can be bypassed by jumper) • reverse and over-voltage protection of jig and phone module Communication and status LED’s • green: Power supply • green: MBUS activity • orange: FBUS activity • jumper to disable LED’s for precise phone module current consumption measurements Spare parts • spring lo
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care • ESD proof material • standard uBGA jig thickness and outer dimensions Views of MJF-53 (note: phone module not included) Page 10 2004 Nokia Corporation.
Company Confidential RH-19/RH-50 4 - Service Tools Nokia Customer Care LRK-2 LGA component rework kit Type designator Description Part code MJS-76 LGA rework Jig 0770417 SES-2 Stencil 0770415 SPS-2 Spreader 0770471 LRK-2 (0273645) Rework procedure Due to the large mechanical tolerance of the power amplifiers the following procedure is necessary: 1 Put power amplifier into the MJS-76 rework jig, the PA should be placed in the best fit location, this is determined by firstly placing it in the
RH-19/RH-50 4 - Service Tools Page 12 Company Confidential Nokia Customer Care 2 Once the best fit location has been found, leave the PA there and put stencil on top of the jig and PA. 3 Put soldering paste on the PA properly. 4 Remove stencil and the PA from the jig. 5 Start soldering process. 2004 Nokia Corporation.
Company Confidential RH-19/RH-50 4 - Service Tools Nokia Customer Care MJS-76 PA LGA rework jig (product code 0770417) Introduction This tool is used in LGA type component reworking purposes in central service centers.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care View of FPS-8 FPS-8C parallel flash prommer (product code: 0080396) The parallel flash prommer FPS-8C is used with MJF-13 and JVB-1. Flash programming can be done to maximum of 8 phones parallel. FPS-8C consists of eight SF11C programming cards. SF11C card is functionally identical to FPS-8. View of FPS-8C Page 14 2004 Nokia Corporation.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools ACF-8 universal power supply (product code: 0680032) ACF-8 universal power supply is used to power FPS-8. ACF-8 has 6 V DC and 2.1 A output. View of ACF-8 CF-8 FLC-2 DC cable (product code: 0730185) The FLC-2 is used to supply a controlled operating voltage. View of FLC-2 Issue 3 05/2004 C-2 2004 Nokia Corporation.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care AXS-4 service cable (product code: 0730090) The AXS-4 D9-D9 service cable is used to connect two 9 pin D connectors e.g. between PC and FPS-8. Cable length is 2 meters. View of AXS-4 XCS-1 service cable (product code: 0730218) The XCS-1 service cable is used to connect FLS-4 to FLA-27. View of XCS-1 Page 16 S-1 2004 Nokia Corporation.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools SW security device PKD-1 (product code: 0750018) SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC. Without the dongle present it is not possible to use the service software. Printer or any such device can be connected to the PC through the dongle if need ed.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care PCS-1 power cable (product code: 0730012) The PCS-1 power cable (DC) is used to connect e.g. JVB-1 to FPS-8. View of PCS-1 of PCS-1 XRF-1 RF cable (product code: 0730085) RF cable XRF-1 is used to connect e.g. module jig MJS-38 to RF measurement equipment. View of XRF-1 Page 18 2004 Nokia Corporation.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools DAU-9S MBUS cable (product code: 0730108) The MBUS cable DAU-9S has a modular connector, and is used with be tween PC's serial port and e.g. module jig MJS-38. View of DAU-9S SCB-3 DC cable (product code: 0730114) The DC cable SCB-3 is used to connect e.g. JVB-1 to the phone. View of SCB-3 Issue 3 05/2004 2004 Nokia Corporation.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care XCS-4 modular cable (product code: 073017) XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing and service purposes. View of XCS-4 Printer cable (product code: 0730029) This cable is used to connect the PC to FPS-8. View of printer cable Page 20 2004 Nokia Corporation.
Company Confidential Nokia Customer Care RH-19/RH-50 4 - Service Tools FLA-30 flash adapter (product code: 0770472) Point of sales flash adapter for RH-19/RH-50 phones. FLA-30 establishes a simple environment for SW update purposes and connects to the same flash test pattern and the phone battery contacts. When using FLA-30 the phone SIM card must be removed and the SIM flap has to be locked close.
RH-19/RH-50 4 - Service Tools Company Confidential Nokia Customer Care This page has been intentionally left blank Page 22 2004 Nokia Corporation.