User Guide

ManualsBrandsNokia ManualsCell Phone30

Customer Care Solutions

TME-3 Series Transceivers

Service Tools

Summary of content (24 pages)

PAGE 3
CCS Technical Documentation TME-3 Service Tools Table of Contents Page No General Instructions ....................................................................................................... 4 XRC-5 RF Cable ..........................................................................................................5 Product code............................................................................................................. 5 JBV-1 Docking Station and MJF-21 Adapter ....................
PAGE 4
TME-3 Service Tools CCS Technical Documentation General Instructions Before connecting the service tools : Caution:Make sure that you have swithed off the PC and the printer before making connections! Caution:Do not connect the PKD-1 key to the serial port. You may damage your PKD-1! Page 4 Copyright Nokia. All rights reserved.
PAGE 5
TME-3 Service Tools CCS Technical Documentation XRC-5 RF Cable RF cable XRC-5 is used to connect e.g. Module Jig MJS-63 to RF measurement equipment.. Attenuation table: Product code XRC-5RF Cable: 900 MHz 0.86dB/m 1800 MHz 1.20dB/m 1900 MHz 1.24dB/m 0730276 Figure 1: View of XRC-5 Issue 3 10/03 Copyright Nokia. All rights reserved.
PAGE 6
TME-3 Service Tools CCS Technical Documentation JBV-1 Docking Station and MJF-21 Adapter The JBV-1 Docking Station has been designed for calibration and software update use. The MJF-21 Docking Station Adapter makes signal connections to the phone. JBV-1 and MJF-21 are used as one unit. In calibration mode JBV-1 is powered by external power supply 11-16VDC. In flashing operation the power for the phone must be taken from external power supply 11-16VDC.
PAGE 7
TME-3 Service Tools CCS Technical Documentation Product Code: MJF-21 Docking Station Adapter: 0770374 Figure 3: View of MJF-21 MJF-21 & JBV-1 setup 1. Attach the protection key PKD-1 to parallel port one (25-pin female D-connector) of the PC. When connecting the PKD-1 to the parallel port be sure that you insert the PC end of the PKD-1 to the PC (male side). If you use a printer on parallel port one, place the PKD-1 between the PC and your printer cable. 2.
PAGE 8
TME-3 Service Tools CCS Technical Documentation FLA-34 Flashing Adapter The FLA-34 Flashing adapter is used for reflashing the TME-3 in a service center. Product Code FLA-34 Flashing Jig: 0770375 Figure 4: View of FLA-34 FLA-34 setup 1. Attach the protection key PKD-1 to parallel port one (25-pin female D-connector) of the PC. When connecting the PKD-1 to the parallel port be sure that you insert the PC end of the PKD-1 to the PC (male side).
PAGE 9
TME-3 Service Tools CCS Technical Documentation MJS-63 Module Jig The MJS-63 Module Jig is used for testing of system/RF-module. Product Code MJS-63 Module Jig: 0770377 Figure 5: View of MJS-63 *Note: The nominal supply voltage for MJS-63 is +8.0 V. The supply voltage must not exceed +12.0 V (min 5V). (MJS-63 has overvoltage protection) For flashing with FPS-8, it is possible to bypass the regulator(jumper). Issue 3 10/03 Copyright Nokia. All rights reserved.
PAGE 10
TME-3 Service Tools CCS Technical Documentation MJS-63 setup 1. Attach the protection key PKD-1 to parallel port one (25-pin female D-connector) of thePC. When connecting the PKD-1 to the parallel port be sure that you insert the PC end of the PKD-1 to the PC (male side). If you use a printer on parallel port one, place the PKD-1 between the PC and your printer cable. 2. Connect the printer cable and D9-D9 cable, AXS-4 to the flash prommer, FPS-8. 3.
PAGE 11
TME-3 Service Tools CCS Technical Documentation MJS-62 Soldering Jig The Soldering Jig MJS-62 is used for soldering and as a rework jig for system module. Product Code MJS-62 Soldering Jig: 0770376 Figure 6: View of MJS-62 Issue 3 10/03 Copyright Nokia. All rights reserved.
PAGE 12
TME-3 Service Tools CCS Technical Documentation FPS-8 Flash Prommer (Sales Pack) The Flash Prommer FPS-8 is used with e.g. FLA-63 and JBV-1. Power is supplied to FPS-8 from a ACF-8 type Power Supply. Also refer to ACS-10.
PAGE 13
TME-3 Service Tools CCS Technical Documentation ACS-10 Power supply module for FPS-8 ACS-10 power supply module replaces the original rear panel of the FPS-8. ACS-10 is needed when programming TME-3. Installation instructions are included in the FPS-8 Flashing User Guide. Product Code ACS-10 Power Supply Module: 0770340 Figure 8: ACS-10 inside Figure 9: ACS-10 rear panel Issue 3 10/03 Copyright Nokia. All rights reserved.
PAGE 14
TME-3 Service Tools CCS Technical Documentation FPS-8C Parallel Flash Prommer (Sales Pack) The Parallel Flash Prommer FPS-8C is used with MJF-6 and JBV-1. Flash programming can be done to maximum of 8 phones parallel. FPS-8C consists of eight SF11C programming cards. SF11C card is functionally identical to FPS-8. Sales package code FPS-8C Parallel Flash Prommer: 0080396 Figure 10: View of FPS-8C Page 14 Copyright Nokia. All rights reserved.
PAGE 15
TME-3 Service Tools CCS Technical Documentation ACF-8 Universal Power Supply ACF-8 Universal Power Supply is used to power FPS-8. ACF-8 has 6 V DC and 2.1 A output. Product Code ACF-8 Universal Power Supply: 0680032 Figure 11: View of ACF-8 Issue 3 10/03 Copyright Nokia. All rights reserved.
PAGE 16
TME-3 Service Tools CCS Technical Documentation AXS-4 Service Cable The AXS-4 D9-D9 Service Cable is used to connect two 9 pin D connectors e.g. between PC and FPS-8. Cable length is 2 meters. Product code AXS-4 D9-D9 Service Cable: 0730090 Figure 12: View of AXS-4 Page 16 Copyright Nokia. All rights reserved.
PAGE 17
TME-3 Service Tools CCS Technical Documentation SW Security Device PKD-1 SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC. Whithout the dongle present it is not possible to use the service software. Printer or any such device can be connected to the PC through the dongle if needed.
PAGE 18
TME-3 Service Tools CCS Technical Documentation FLS-4S POS (Point Of Sale) Flash Device (Sales Pack) FLS-4S is a dongle and flash device incorporated into one package, developed specifically for POS use. Product Code Sales Pack - Europe/Africa 0080541 Sales Pack -APAC 0080542 Sales Pack -Americas 0080543 View of FLS-4 Figure 14: View of FLS-4S POS Flash setup 1. Attach the POS flash adapter FLS-4S to parallel port one (25-pin female D-connector) of the PC. 2.
PAGE 19
TME-3 Service Tools CCS Technical Documentation PCS-1 Power Cable The PCS-1 Power Cable (DC) is used to connect e.g. JBV-1 to FPS-8. Product Code PCS-1 Power Cable: of PCS-1 Issue 3 10/03 0730012 Figure 15: View of PCS-1 Copyright Nokia. All rights reserved.
PAGE 20
TME-3 Service Tools CCS Technical Documentation DAU-9S MBUS Cable The MBUS Cable DAU-9S has a modular connector, and is used with between PC's serial port and e.g. Module Jig MJS-63. Product Code DAU-9S MBUS Cable: 0730108 Figure 16: View of DAU-9S Page 20 Copyright Nokia. All rights reserved.
PAGE 21
TME-3 Service Tools CCS Technical Documentation XCS-4 Modular Cable XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing and service purposes. Product code XCS-4 Modular Cable: 0730178 Figure 17: View of XCS-4 Issue 3 10/03 Copyright Nokia. All rights reserved.
PAGE 22
TME-3 Service Tools CCS Technical Documentation Parallel Cable CA-10 DS The 1.8m bidirectional parallel cable is used to connect the PC to FPS-8. IEEE 1284-1944 standard compatible. Product code Parallel Cable CA-10DS : w of Printer Cable Page 22 0730298 Figure 18: View of Parallel Cable Copyright Nokia. All rights reserved.
PAGE 23
TME-3 Service Tools CCS Technical Documentation SB-1 Service Box for TME-3 The primary physical interface to the application is through the 50-pin M2M System Connector. The M2M system connector offers serial bus, power input/output, Digital Audio Interface, analogue audios and remote I/O control. The 50-pin system connector is connected to the application module with a flat cable connector. The flat cable is connected to a pin header connector on the customer application.
PAGE 24
TME-3 Service Tools CCS Technical Documentation DTX-3 Nokia 32 Application module DTX-3 Nokia 32 Application module is used for Nokia 30 final testing (audios). Product code: DTX-3 NOKIA 32 AM SWAP PACKAGE: 0046604 Figure 20: DTX-3 Page 24 Copyright Nokia. All rights reserved.