Nokia Customer Care Service Manual RM-258; RM-259 (Nokia 2760) Mobile Terminal Part No: 9203122 (Issue 1) COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Amendment Record Sheet Amendment Record Sheet Amendment No Issue 1 Page ii Date 06/2007 Inserted By Comments Y Liu COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Copyright Copyright Copyright © 2007 Nokia. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia, Nokia Connecting People, and Nokia X and Y are trademarks or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.
RM-258; RM-259 Warnings and cautions Warnings and cautions Warnings • IF THE DEVICE CAN BE INSTALLED IN A VEHICLE, CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND ANTI-SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE DEALER/ MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY.
RM-258; RM-259 For your safety For your safety QUALIFIED SERVICE Only qualified personnel may install or repair phone equipment. ACCESSORIES AND BATTERIES Use only approved accessories and batteries. Do not connect incompatible products. CONNECTING TO OTHER DEVICES When connecting to any other device, read its user’s guide for detailed safety instructions. Do not connect incompatible products. Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Care and maintenance Care and maintenance This product is of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. • Keep the phone and all its parts and accessories out of the reach of small children. • Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits.
RM-258; RM-259 ESD protection ESD protection Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use. To replace the covers ESD protection must be applied. All electronic parts of the product are susceptible to ESD.
RM-258; RM-259 Battery information Battery information Note: A new battery's full performance is achieved only after two or three complete charge and discharge cycles! The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.
RM-258; RM-259 Company Policy Company Policy Our policy is of continuous development; details of all technical modifications will be included with service bulletins. While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing/email.
RM-258; RM-259 Company Policy (This page left intentionally blank.) Page x COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Nokia 2760 Service Manual Structure Nokia 2760 Service Manual Structure 1 General Information 2 Service Tools and Service Concepts 3 Baseband Troubleshooting Instructions 4 RF Troubleshooting Instructions 5 Camera Module Troubleshooting 6 System Module Glossary Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Nokia 2760 Service Manual Structure (This page left intentionally blank.) Page xii COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
Nokia Customer Care 1 — General Information Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 General Information (This page left intentionally blank.) Page 1 –2 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 General Information Table of Contents RM-258/RM-259 product selection .......................................................................................................................1–5 Features...................................................................................................................................................................1–5 Hardware features ..............................................................................................................
RM-258; RM-259 General Information (This page left intentionally blank.) Page 1 –4 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 General Information RM-258/RM-259 product selection The RM-258 is the EU version of the telephone with a dual band transceiver unit designed for the GSM900 and GSM1800 networks. The RM-259 is the US version of the telephone with a dual band transceiver unit designed for the GSM850 and GSM1900 networks.
RM-258; RM-259 General Information Software features • OS: ISA • UI Style: S40 • MIDP 2.0 Java, with latest APIs • Browser: XHTML over TCP/IP (WAP 2.0 compliant) • Video capture and playback (7.5fps, H.263; MPEG4) • MMS 1.2 • IMPS 1.
RM-258; RM-259 General Information Table 2 Car Type Name CK-15W Display car kit CK-20W Multimedia car kit CK-25W Multimedia car kit Table 3 Audio Type Name HS-38W Nokia bluetooth headset BH-202 HS-40 Headset HS-47 Stereo headset HS-50W Nokia bluetooth headset BH-300 HS-51W Nokia bluetooth headset BH-301 HS-52W Nokia bluetooth headset BH-201 HS-58W Nokia bluetooth headset BH-200 HS-68W Nokia bluetooth headset BH-203 HS-73W Nokia bluetooth headset BH-302 HS-78W Nokia bluetooth h
RM-258; RM-259 General Information Battery endurance Nokia measurements of operation times in GSM900/1800 Talk time Battery: BL-4B 700mAh 400 mins Standby time Battery: BL-4B 700mAh 350 hours Note: Variation in operation times will occur depending on SIM card, network settings and usage. Talk time is increased by up to 30% if half rate is active and reduced by 5% if enhanced full rate is active. Environmental conditions Environmental condition Ambient temperature Notes Normal operation -15 oC ...
RM-258; RM-259 General Information Voltage Voltage (V) Condition Nominal voltage 3.90V a Lower extreme voltage 3.30V b Higher extreme voltage 4.30V c HW shutdown voltages Vmstr+ 2.1V ± 0,1V Off to on Vmstr- 1.9V ± 0,1V On to off SW shutdown voltages SW shutdown 3. 1V In call SW shutdown 3. 2V In idle Min operating voltage Vcoff+ 3. 1V ± 0,1V Off to on Vcoff- 2. 8V ± 0,1V On to off HW reset demands Min 1. 0V Max -- d a.
RM-258; RM-259 General Information (This page left intentionally blank.) Page 1 –10 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
Nokia Customer Care 2 — Service Tools and Service Concepts Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts (This page left intentionally blank.) Page 2 –2 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts Table of Contents Service tools............................................................................................................................................................2–5 CA-106DS ............................................................................................................................................................2–5 CA-111DS ............................................................................................
RM-258; RM-259 Service Tools and Service Concepts (This page left intentionally blank.) Page 2 –4 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts Service tools The table below gives a short overview of service tools that can be used for testing, error analysis and repair of product RM-258; RM-259, refer to various concepts. CA-106DS Easy flash II cable The cable is used for connecting phone DC port to the flash prommer FPS-10. CA-111DS Easy flash II cable The cable is used for connecting phone DC port to either POS flashing device FLS-4S or to the PROMMER box FPS-11.
RM-258; RM-259 Service Tools and Service Concepts CA-41PS Power cable Power cable for connection of e.g. the JBV-1 docking station to the FPS-10 prommer box. CA-52PS DC Cable The cable is used to connect JBV-1 docking station to the phone charger jack for ADC/VCHAR/ICHAR calibration. DA-64 Docking station adapter The docking station adapter is used for this phone in combination with JBV-1.
RM-258; RM-259 Service Tools and Service Concepts FLS-4S Flash device FLS-4S is a dongle and flash device incorporated into one package, developed specifically for POS use. FLS-5 Flash device FLS-5 is a dongle and flash device incorporated into one package, developed specifically for POS use.
RM-258; RM-259 Service Tools and Service Concepts FPS-11 Parallel flash prommer FPS-11 interfaces with: • PC • Control unit • Flash adapter • Smart card FPS-11 flash prommer features: • Can flash up to 8 phones at a time, controlled by one PC • Communication method between PC and FPS-11 is single USB2.
RM-258; RM-259 Service Tools and Service Concepts MJ-137 Module jig MJ-137 is meant for component level troubleshooting. The jig includes an RF interface for GSM and Bluetooth.
RM-258; RM-259 Service Tools and Service Concepts PK-1 Software protection key PK-1 is a hardware protection key with a USB interface. It has the same functionality as the PKD-1 series dongle. PK-1 is meant for use with a PC that does not have a series interface. To use this USB dongle for security service functions please register the dongle in the same way as the PKD-1 series dongle.
RM-258; RM-259 Service Tools and Service Concepts SA-93 RF coupler The coupler is used for Go/No-Go test after changing components in the RF part of the phone. It is mounted on the docking station adapter.
RM-258; RM-259 Service Tools and Service Concepts ST-28 rework stencil This stencil is used together with RJ-72 to rework N7600. ST-30 Rework stencil It is used together with RJ-51 to rework the Front End Module (FEM) N7700. SX-4 Smart card SX-4 is a BB5 security device used to protect critical features in tuning and testing. SX-4 is also needed together with FPS-10 when DCT-4 phones are flashed.
RM-258; RM-259 Service Tools and Service Concepts XRS-6 RF cable The RF cable is used to connect, for example, a module repair jig to the RF measurement equipment. SMA to N-Connector approximately 610 mm. Attenuation for: • GSM850/900: 0.3+-0.1 dB • GSM1800/1900: 0.5+-0.1 dB • WLAN: 0.6+-0.1dB Service concepts POS flash concept with FLS-4S Figure 2 POS flash concept with FLS-4S Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts POS flash concept with FLS-5 Figure 3 POS flash concept with FLS-5 Page 2 –14 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts Flash concept with FPS-10 Figure 4 Flash concept with FPS-10 Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts RF-test/BB-tune concept with JBV-1 Figure 5 RF-test/BB-tune concept with JBV-1 Page 2 –16 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts EM calibration concept with JBV-1 Figure 6 EM calibration concept with JBV-1 Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts RF-test/BB-tune & flash concept with JBV-1, FPS-10 Figure 7 RF-test/BB-tune & flash concept with JBV-1, FPS-10 Page 2 –18 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts RF/BB tune& flash concept with MJ-137, FPS-10 Figure 8 RF/BB tune& flash concept with MJ-137, FPS-10 Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Service Tools and Service Concepts (This page left intentionally blank.) Page 2 –20 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
Nokia Customer Care 3 — Baseband Troubleshooting Instructions Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions (This page left intentionally blank.) Page 3 –2 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Table of Contents General baseband troubleshooting......................................................................................................................3–5 Key components ................................................................................................................................................3–5 Power supply test points...................................................................................................
RM-258; RM-259 Baseband Troubleshooting Instructions Figure 24 Earpiece fault flow chart ................................................................................................................... 3–23 Figure 25 IHF/ringing tone fault flow chart...................................................................................................... 3–24 Figure 26 Microphone fault flow chart..............................................................................................................
RM-258; RM-259 Baseband Troubleshooting Instructions General baseband troubleshooting Key components Power supply test points Phone cannot be powered on (I) Context This means that the phone does not use any current at all when the supply is connected and/or power key is pressed. It is assumed that the voltage supplied is 3.6VDC. The UEMCLite will prevent any functionality at battery/supply levels below 2.9VDC. Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Troubleshooting flow Figure 9 Troubleshooting when phone cannot be powered on Page 3 –6 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Phone cannot be powered on (II) Context If this kind of failure is presenting itself immediately after FLALI, it is most likely caused by ASIC's missing contact with PWB. If the MCU doesn’t service the watchdog register within the UEMCLite, the operations watchdog will run out after approximately 32 seconds. Unfortunately, the service routine can not be measured.
RM-258; RM-259 Baseband Troubleshooting Instructions Phone cannot be flashed Context The flash programming can be done via the pads on the PWB (J2060). If failed, then follow up the trouble shooting flow chart. In case of flash failure in the FLALI station, swap the phone and send it back to the care program for further analysis. Possible failures could be short-circuit of balls under µBGAs (UEMCLite, UPP4M, FLASH), or missing or misaligned components.
RM-258; RM-259 Baseband Troubleshooting Instructions Troubleshooting flow Figure 11 Flash programming fault Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Easy flash programming does not work Context The flash programming can be done via the easy flash connector. If failed, then follow up the trouble shooting below. It is not possible to verify if there is a short circuit in control and address lines of MCU (UPP8M) and memory (flash) because BGA package is used in RM-258/259. Page 3 –10 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Troubleshooting flow Figure 12 Easy flash programming fault Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Display shows "Contact Service" Troubleshooting flow This error can only happen at power up where several self-tests are run. If any of these test cases fails the display will show the message: "Contact Service". They are individual test cases, so the below lineup of error hunting's has no chronological order. Use common sense and experience to decide which test case to start error hunting at. Page 3 –12 COMPANY CONFIDENTIAL Copyright © 2007 Nokia.
RM-258; RM-259 Baseband Troubleshooting Instructions Figure 13 Troubleshooting when the "Contact Service" message is seen The phone does not register to the networks, or the phone cannot make a call Context If the phone doesn't register to the network, the fault can be in either BB or RF. Only few signals can be tested since several signals are 'buried' in one or more of the inner layers of the PWB.
RM-258; RM-259 Baseband Troubleshooting Instructions Troubleshooting flow Figure 14 No registering or call Page 3 –14 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions SIM related faults Insert SIM card fault Troubleshooting flow The hardware of the SIM interface from UEMCLite (D2200) to the SIM connector (X2700) can be tested without a SIM card. When the power is switched on the phone first check for a 1.8V SIM card and then a 3V SIM card. The phone will try this four times, where after it will display ”Insert SIM card”. Figure 15 Insert SIM card fault Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia.
RM-258; RM-259 Baseband Troubleshooting Instructions Figure 16 Signal diagram SIM card rejected The error ”SIM card rejected” means that the ATR message received from SIM card is corrupted, e.g. data signal levels are wrong. The first data is always ATR and it is sent from card to phone. For reference a picture with normal SIM power-up is shown below. Figure 17 Signal diagram User interface Blank display Context The display does not show any information at all.
RM-258; RM-259 Baseband Troubleshooting Instructions Troubleshooting flow Corrupted display Context The display contains missing or fading segments, or color presentation is incorrect. Troubleshooting flow Dead keys Context One or more keys has no function. Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Troubleshooting flow No backlight for display or/and keys Context There are 3 kinds of statuses: No backlight for both display and keys; No backlight for only display; No backlight for only keys. Troubleshooting flow Page 3 –18 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Audio troubleshooting Audio troubleshooting using phoenix Figure 18 Phoenix audio test window Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Figure 19 4-pole jack plug for audio accessory Table 6 Connector for External Audio Accessories Pin Signal name Direction Description 5 PLUGDET Input Terminal internal connection, plug detection 4 HS EAR L Output Audio output 3 HS EAR R Output Audio output 2 HS MIC Input Multiplexed microphone audio and control data 1 HS GND - Ground contact Check microphone using "Hp microphone in Ext speaker out" loop Steps 1.
RM-258; RM-259 Baseband Troubleshooting Instructions 7. Check if signal is detected at HS EAR L/R, shown in Figure 4-pole jack plug for audio accessory above. Figure 20 Test arrangement for microphone Check earpiece using "Ext microphone in Hp speaker out" loop Steps 1. Connect phone with Phoenix. 2. Open the Audio Test window from Testing→ Audio test , as shown in Figure Phoenix audio test window above. 3. Select Ext microphone in Hp speaker out. 4. Select Acc.Detection as Off. 5. Select Loop as On. 6.
RM-258; RM-259 Baseband Troubleshooting Instructions 5. Check if sound is heard in IHF. Figure 22 Checking IHF and ring tone by using "Buzzer" Check vibra function using "Vibra control" Steps 1. Connect phone with Phoenix. 2. Open “Vibra control” window from “Testing -> Vibra control”, as shown in the figure below. 3. Select suitable intensity value, for example 53 %. 4. Select “Vibra state” as “Enabled” 5. Click “Write”. 6. Check if Vibra works.
RM-258; RM-259 Baseband Troubleshooting Instructions Earpiece fault Troubleshooting flow Figure 24 Earpiece fault flow chart Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions IHF/ringing tone fault Troubleshooting flow Figure 25 IHF/ringing tone fault flow chart Page 3 –24 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Microphone fault Troubleshooting flow Figure 26 Microphone fault flow chart Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Headset earpiece fault Troubleshooting flow Figure 27 Headset earpiece fault flow chart Page 3 –26 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions Headset microphone fault Troubleshooting flow Figure 28 Headset microphone fault flow chart Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Baseband Troubleshooting Instructions (This page left intentionally blank.) Page 3 –28 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
Nokia Customer Care 4 — RF Troubleshooting Instructions Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions (This page left intentionally blank.) Page 4 –2 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Table of Contents General RF troubleshooting ..................................................................................................................................4–7 General RF troubleshooting .............................................................................................................................4–7 RF key components ...............................................................................................................
RM-258; RM-259 RF Troubleshooting Instructions Figure 31 Supply point at RF IC (N7600) ..............................................................................................................4–9 Figure 32 Supply point at BT & FM IC (N6000) .................................................................................................. 4–10 Figure 33 GSM900 RF controls window .............................................................................................................
RM-258; RM-259 RF Troubleshooting Instructions Figure 83 FM circuit troubleshooting diagram................................................................................................. 4–51 Figure 84 Bluetooth and FM radio test points.................................................................................................. 4–52 Figure 85 XAUDIO output signal.........................................................................................................................
RM-258; RM-259 RF Troubleshooting Instructions (This page left intentionally blank.) Page 4 –6 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions General RF troubleshooting General RF troubleshooting Most RF semiconductors are static discharge sensitive Two types of measurements are used in the following. It will be specified if the measurement type is "RF" or "LF". • RF measurements are done with a Spectrum Analyzer and a high-frequency 500 ohm passive probe, for example HP54006A. (Note that when measuring with the 500ohm probe the signal will be around 20dB attenuated.
RM-258; RM-259 RF Troubleshooting Instructions RF key components Figure 29 RF key components on PWB N7600 Mjoelner RF IC N7700 FEM (PA and antenna switch) Z7602 EGSM 850/900 RX SAW filter Z7600 DCS 1800/PCS1900 RX SAW filter Z7603 EGSM 850/900 TX filter Z7604 DCS 1800/PCS1900 TX filter B7600 26 MHz crystal Page 4 –8 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions N6000 BT & FM IC Z6000 BT SAW filter Refer to the picture below for measuring points at the UEM (D2200). Figure 30 Supply points at UEM (D2200) Figure 31 Supply point at RF IC (N7600) Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 32 Supply point at BT & FM IC (N6000) Auto tuning This phone can be tuned automatically. Autotune is designed to align the phone's RF part easier and faster. It performs calibrations, tunings and measurements of RX and TX. The results are displayed and logged in a result file, if initiated. Hardware set up Hardware requirements for auto tuning: • PC (Windows 2000/NT) with GPIB card • Power supply • Product specific module jig • Cables: 3 (alt.
RM-258; RM-259 RF Troubleshooting Instructions 2 The first time you are using automatic tuning on this phone model, on this computer, you will have to Set loss for cables and jigs. 3 To go to autotune, select Tuning (Alt-U) > Auto-Tune (Alt-A) from the menu. 4 If you need more assistance, please refer to the Phoenix Help. RM-258 receiver General instructions for GSM900 RX troubleshooting Steps 1. Connect the phone to a PC with the module repair jig. 2.
RM-258; RM-259 RF Troubleshooting Instructions Figure 33 GSM900 RF controls window Page 4 –12 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM900 receiver Troubleshooting flow Figure 34 GSM900 receiver troubleshooting Results By measuring with an oscilloscope at RXIP or RXQP on a working GSM900 receiver this picture should be seen. Signal amplitude peak-peak 108mV. DC offset 1.0V. Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 35 900 RX I/Q signal waveform General instructions for GSM 1800 RX troubleshooting Steps 1. Connect the phone to a PC with the module repair jig. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Select File and Scan product. 4. Wait a while for the PC to read the information from the phone. 5. Select Testing and RF Controls. 6.
RM-258; RM-259 RF Troubleshooting Instructions Figure 36 GSM1800 RF controls window Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM1800 receiver Troubleshooting flow Figure 37 GSM1800 receiver troubleshooting Results By measuring with an oscilloscope at RXIP or RXQP on a working GSM1800 receiver this picture should be seen. Signal amplitude peak-peak 114mV. DC offset 1.0V. Page 4 –16 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 38 1800 RX I/Q signal waveform Measurement points in the receiver Figure 39 RX measurements point of the control voltages to FEM N7700 Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 40 Measurement points at the RX SAW Filters – Z7600/Z7602 Figure 41 RX I/Q signals RM-258 transmitter General instructions for GSM 900 TX troubleshooting Steps 1. Apply a RF-cable to the RF-connector to allow the transmitted signal act as normal. RF-cable should be connected to an attenuator at least 10dB before connected to the measurement equipment, otherwise the PA may be damaged. 2.
RM-258; RM-259 RF Troubleshooting Instructions 3. Select File and Scan product. 4. Wait a while for the PC to read the information from the phone. 5. Select Testing and RF Controls. 6. Set the parameters as follows: i Band: GSM 900 ii Active Unit: TX iii TX Power Level: 5 iv TX Data Type: Random Results The setup should now look like this: Figure 42 GSM 900 RF controls window Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM900 transmitter Troubleshooting flow Figure 43 GSM900 tarnsmitter troubleshooting GSM900 TX output power Measure the output power of the phone; it should be about 32.5dBm. Remember the cable loss is about 0.3dB. Page 4 –20 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 44 TX I/O signal Figure 45 VC1, VC3 signals Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 46 TXP signal Figure 47 TXC signals at PCL5 Page 4 –22 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 48 TXC signals at PCL19 General instructions for GSM1800 TX troubleshooting Steps 1. Apply a RF-cable to the RF-connector to allow the transmitted signal act as normal. RF-cable should be connected to an attenuator at least 10dB before connected to the measurement equipment, otherwise the PA may be damaged. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Select File and Scan product. 4.
RM-258; RM-259 RF Troubleshooting Instructions Figure 49 GSM 1800 RF controls window Page 4 –24 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM1800 transmitter Troubleshooting flow Figure 50 GSM1800 transmitter troubleshooting GSM1800 TX output power Measure the output power of the phone; it should be about 29.5dBm. Remember the cable loss is about 0.5dB. Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 51 TX I/O signal Figure 52 VC1, VC2, VC3 signals Page 4 –26 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 53 TXP signal Figure 54 TXC signals at PCL0 Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 55 TXC signals at PCL15 RM-259 receiver General instructions for GSM 850 RX troubleshooting Steps 1. Connect the phone to a PC with the module repair jig. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Select File and Scan product. 4. Wait a while for the PC to read the information from the phone. 5. Select Testing and RF Controls. 6.
RM-258; RM-259 RF Troubleshooting Instructions Figure 56 GSM850 RF controls window Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM850 receiver Troubleshooting flow Figure 57 GSM850 receiver troubleshooting Page 4 –30 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Results By measuring with an oscilloscope at RXIP or RXQP on a working GSM850 receiver this picture should be seen. Signal amplitude 114mVp-p. DC offset 1.0V. Figure 58 850 RX I/Q signal waveform General instructions for GSM1900 RX troubleshooting Steps 1. Connect the phone to a PC with the module repair jig. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Select File and Scan product. 4.
RM-258; RM-259 RF Troubleshooting Instructions Figure 59 GSM 1900 RF controls window Page 4 –32 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM1900 receiver Troubleshooting flow Figure 60 GSM1900 receiver troubleshooting Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Results By measuring with an oscilloscope at RXIP or RXQP on a working GSM1900 receiver this picture should be seen. Signal amplitude 108 mVp-p. DC offset 1.0V. Figure 61 1900 RX I/Q signal waveform Page 4 –34 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Measurement points in the receiver Figure 62 RX measurements point of the control voltages to FEM N7700 Figure 63 Measurement points at the RX SAW Filters – Z7600/Z7602 Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 64 RX I/Q signals RM-259 transmitter General instructions for GSM 850 TX troubleshooting Steps 1. Apply a RF-cable to the RF-connector to allow the transmitted signal act as normal. RF-cable should be connected to an attenuator at least 10dB before connected to the measurement equipment, otherwise the PA may be damaged. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Select File and Scan product. 4.
RM-258; RM-259 RF Troubleshooting Instructions Figure 65 GSM 850 RF controls window Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM850 transmitter Troubleshooting flow Figure 66 GSM850 transmitter troubleshooting Page 4 –38 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions GSM850 TX output power Measure the output power of the phone; it should be about 32.5 dBm. Remember the cable loss is about 0.3 dB. Figure 67 TX I/O signal Figure 68 VC1, VC3 signal Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 69 TXP signal Figure 70 TXC signals at PCL5 Page 4 –40 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 71 TXC signals at PCL19 General instructions for GSM1900 TX troubleshooting Steps 1. Apply a RF-cable to the RF-connector to allow the transmitted signal act as normal. RF-cable should be connected to an attenuator at least 10dB before connected to the measurement equipment, otherwise the PA may be damaged. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Select File and Scan product. 4.
RM-258; RM-259 RF Troubleshooting Instructions 7. The setup should now look like this: Figure 72 GSM 1900 RF controls window Page 4 –42 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for GSM1900 transmitter Troubleshooting flow Figure 73 GSM1900 transmitter troubleshooting Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions GSM1900 TX output power Measure the output power of the phone; it should be about 29.5 dBm. Remember the cable loss is about 0.5 dB. Figure 74 TX I/O signal Figure 75 VC1, VC2, VC3 signals Page 4 –44 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 76 TXP signal Figure 77 TXC signals at PCL0 Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 78 TXC signals at PCL15 Synthesizer troubleshooting Introduction 26 MHz Reference Oscillator (VCXO) There is only one PLL synthesizer generating Local Oscillator frequencies for both RX and TX in both bands (PCN and EGSM). The VCO frequency is divided by 2 for PCN operation or by 4 for EGSM operation inside the Mjoelner IC. The 26MHz oscillator is located near the Mjoelner IC. (N7600).
RM-258; RM-259 RF Troubleshooting Instructions Figure 79 VCXO 26 MHz waveform Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for PLL synthesizer Figure 80 PLL Troubleshooting diagram Page 4 –48 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Measurement points at the VCXO Figure 81 Measurement point for VCXO FM radio and bluetooth troubleshooting Measurement settings Steps 1. Connect the phone to a PC with the module repair jig. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Phoenix settings shall be as follows: Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Figure 82 Phoenix settings 4. Establish input of a standard FM signal to the FM module. 5. Signal generator settings shall be as follows: i Frequency: 98 MHz ii Level: - 60 dBm iii FM deviation: 75 kHz iv LFGEN frequency: 1 kHZ Page 4 –50 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Troubleshooting diagram for FM radio Troubleshooting flow Issue 1 CONFIDENTIAL diagram Figure 83COMPANY FM circuit troubleshooting Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Bluetooth and FM radio test points Figure 84 Bluetooth and FM radio test points Figure 85 XAUDIO output signal Figure 86 FM module output signal Introduction to Bluetooth troubleshooting There are two main Bluetooth (BT) problems that can occur: Page 4 –52 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Problem Description Detachment of the BT antenna. This would most likely happen if the device has been dropped repeatedly to the ground. It could cause the BT antenna to become loose or partially detached from the PWB. A malfunction in the BT ASIC, BB ASICs or the phone’s BT SMD components. This is unpredictable and could have many causes i.e. SW or HW related.
RM-258; RM-259 RF Troubleshooting Instructions Figure 87 BER test result Bluetooth self tests in Phoenix Steps 1. Start Phoenix service software. 2. ChooseFile→Scan Product. 3. Place the phone to a flash adapter. 4. From the Mode drop-down menu, set mode to Local. 5. Choose Testing→Self Tests. 6. In the Self Tests window check the following Bluetooth related tests: • ST_LPRF_IF_TEST • ST_LPRF_AUDIO_LINES_TEST • ST_BT_WAKEUP_TEST Page 4 –54 COMPANY CONFIDENTIAL Copyright © 2007 Nokia.
RM-258; RM-259 RF Troubleshooting Instructions 7. To run the tests, click Start. Figure 88 Bluetooth self tests in Phoenix Bluetooth BER failure troubleshooting Context Basic encoding rules, BER, is a self-identifying and self-delimiting encoding scheme, which means that each data value can be identified, extracted and decoded individually. Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Part 1: Bluetooth self test passed but BER test failed Page 4 –56 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Part 2: Bluetooth self test failed Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Bluetooth audio and UI activation troubleshooting Troubleshooting flow Page 4 –58 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions Antenna troubleshooting Antenna troubleshooting diagram Troubleshooting flow Figure 89 Antenna troubleshooting Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 RF Troubleshooting Instructions (This page left intentionally blank.) Page 4 –60 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
Nokia Customer Care 5 — Camera Module Troubleshooting Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Camera Module Troubleshooting (This page left intentionally blank.) Page 5 –2 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Camera Module Troubleshooting Table of Contents Introduction to camera module troubleshooting ..............................................................................................5–5 The effect of image taking conditions on image quality ...................................................................................5–6 Camera construction ...........................................................................................................................................
RM-258; RM-259 Camera Module Troubleshooting (This page left intentionally blank.) Page 5 –4 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Camera Module Troubleshooting Introduction to camera module troubleshooting Background, tools and terminology Faults or complaints in camera operation can be roughly categorised into three subgroups: 1 Camera is not functional at all; no image can be taken. 2 Images can be taken but there is nothing recognizable in them. 3 Images can be taken and they are recognizable but for some reason the quality of images is seriously degraded.
RM-258; RM-259 Camera Module Troubleshooting Sensitivity Camera module's sensitivity to light. In equivalent illumination conditions, a less sensitive camera needs a longer exposure time to gather enough light in forming a good image. Analogous to ISO speed in photographic film. Sharpness Good quality images are 'sharp' or 'crisp', meaning that image details are well visible in the picture.
RM-258; RM-259 Camera Module Troubleshooting Figure 91 Blurring caused by shaking hands Movement in bright light If an image is taken of moving objects or if the device is used in a moving vehicle, object 'skewing' or 'tilting' may occur. This phenomenon is fundamental to most CMOS camera types, and usually cannot be avoided. The movement of camera or object sometimes cause blurring indoors or in dim lighting conditions because of long exposure time. This is normal; do not change the camera module.
RM-258; RM-259 Camera Module Troubleshooting Temperature High temperatures inside the mobile phone cause more noise to appear in images. For example, in +70 degrees (Celsius), the noise level may be very high, and it further grows if the conditions are dim. If the phone processor has been heavily loaded for a long time before taking an image, the phone might have considerably higher temperature inside than in the surrounding environment.
RM-258; RM-259 Camera Module Troubleshooting Flicker In some occasions a bright fluorescent light may cause flicker in the viewfinder and captured image. This phenomenon may also be a result, if images are taken indoors under the mismatch of 50/60 Hz electricity network frequency. The electricity frequency used is automatically detected by the camera module. In some very few countries, both 50 and 60 Hz networks are present and thus probability for the phenomenon increases.
RM-258; RM-259 Camera Module Troubleshooting Examples of good quality images Figure 97 Good image taken indoors Figure 98 Good image taken outdoors Camera construction This section describes the mechanical construction of the camera module for getting a better understanding of the actual mechanical structure of the module. Table 7 Camera specifications Sensor type CMOS Sensor Photo detectors 0.3 million F number/Aperture f/2.8 Focal length 1.
RM-258; RM-259 Camera Module Troubleshooting Video resolutions 128x96, at 13 frames per second Video clip length 9 seconds or free, maximal clip length in free mode is 2 minutes (limited by the data storing capabilities of the device) Video file format 3GPP, *.3gp Exposure Automatic White Balance Automatic Colours 16.
RM-258; RM-259 Camera Module Troubleshooting Figure 100 Camera module bottom view including serial numbering The camera module as a component is not a repairable part, meaning that the components inside the module may not be changed. Cleaning dust from the front face is allowed only. Use clean compressed air. The camera module uses socket type connecting. For versioning, laser marked serial numbering is used on the PWB. The main parts of the module are: • Lens unit including lens aperture.
RM-258; RM-259 Camera Module Troubleshooting In Service software press “Read”, and the Camera Configuration window shows available DCC data file name and its version to upload. If the previous camera configuration was the same as installed, then Current Configuration Version displays DCC data version currently in the terminal memory, otherwise it shows xxx.xxx. Press “Upload” and then the DCC data settings are updated.
RM-258; RM-259 Camera Module Troubleshooting Figure 102 Effects of dust on optical path If large dust particles get trapped on top of the lens surface in the cavity between camera window and lens, they will cause image blurring and poor contrast. The dust gasket between the window and lens should prevent any particles from getting into the cavity after the manufacturing phase. Dust in this position should be blown away by using compressed air.
RM-258; RM-259 Camera Module Troubleshooting 5 The protection window is defective. This can be either a manufacturing failure or caused by the user. The window should be changed. 6 The camera lens is misfocused because of a manufacturing error. 7 Very high level of digital zoom is used A quantitative analysis of sharpness is very difficult to conduct in any other environment than optics laboratory. Therefore, subjective analysis should be used.
RM-258; RM-259 Camera Module Troubleshooting Usually bit errors can be easily detected in images, and they are best visible in full resolution images. A good practice is to use a uniform white test target when analysing these errors. The errors are clearly visible, colourful sharp dots or lines in camera images. See the following figure. Figure 105 Bit errors caused by JPEG compression One type of bit error is a lack of bit depth.
RM-258; RM-259 Camera Module Troubleshooting Troubleshooting flow Note: Make sure that the phone has the latest software before continuing. Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Camera Module Troubleshooting Camera baseband HW troubleshooting Troubleshooting flow Page 5 –18 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Camera Module Troubleshooting Camera viewfinder troubleshooting Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Camera Module Troubleshooting Bad camera image quality troubleshooting Troubleshooting flow Page 5 –20 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
Nokia Customer Care 6 — System Module Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 System Module (This page left intentionally blank.) Page 6 –2 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 System Module Table of Contents System module block diagram .............................................................................................................................6–5 Baseband description ............................................................................................................................................6–6 Functional description .......................................................................................................................
RM-258; RM-259 System Module Figure 111 HALL sensor....................................................................................................................................... 6–11 Figure 112 Keyboard schematics ....................................................................................................................... 6–16 Figure 113 Keyboard layout in UI side ..............................................................................................................
RM-258; RM-259 System Module System module block diagram The main board consists of a radio frequency part and a baseband part. The User Interface parts are situated at the UI side, which is on the opposite side of the engine board. The 2CP is the engine module of the mobile device, and the 2CQ is the UI module of module of the mobile device. Figure 106 Module block diagram Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 System Module Baseband description Functional description The BB core is based on UPP8M CPU. UPP8M takes care of all the signal processing and operation controlling tasks of the mobile device. For power management, there is one main ASIC for controlling charging and supplying power UEMCLite plus a discrete power supply. The main reset for the system is generated by the UEMCLite. The memory comprises of 128 Mbit flash and 16 Mbit PsRAM.
RM-258; RM-259 System Module Energy management Filter components The master of EM control is UEMCLite and with SW it has the main control of the system voltages and operating modes. The power distribution diagram is presented in the illustration below. Figure 107 Power connection diagram All connectors going to the “outside world” have filter components, ESD protection and EMC reduction. The Digital/Data lines on SIM have special dedicated filter ASIP. The below figure show the SIM filtering.
RM-258; RM-259 System Module The Audio circuit: Earpiece, IHF, internal microphone and external speaker are filtered with discrete components (common mode reduction coils, Varistors, caps and resistors), where as the external microphone uses differential mode mic. ASIP The 16 UEMECLite BB & RF regulators are specified to have a decoupling cap of 1 µF ±20%. Modes of operation BB4.
RM-258; RM-259 System Module Figure 109 Audio block diagram UEMcLite supports three microphone inputs and two outputs. The inputs can be used for internal, headset or handsfree microphones. The microphone signals from different sources are connected to separate inputs at the UEMcLite ASIC. The inputs and outputs are all differential. Three inputs (MIC1, MIC2) and two outputs (EAR, HF) are used in the phone. MIC1P/MIC1N inputs are used for the internal microphone, using single-ended biasing circuitry.
RM-258; RM-259 System Module Figure 110 4-pole jack plug for audio accessory Table 9 Connector for External Audio Accessories Pin Signal name Direction Description 5 PLUGDET Input Terminal internal connection, plug detection 4 HS EAR L Output Audio output 3 HS EAR R Output Audio output 2 HS MIC Input Multiplexed microphone audio and control data 1 HS GND - Ground contact HALL sensor The HALL sensor is used to recognize the position of the flap.
RM-258; RM-259 System Module Figure 111 HALL sensor Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 System Module Interfaces RF and baseband interfaces Table 10 AC and DC Characteristics of BB4.0 LiteV2 RF-Base band Digital Signals Signal name From To Para-meter Input characteristics Min TXP1 UPP RFGenOu t3 GenIO5 TXP2 UPP RF-IC RF-IC (GenIO6 ) RFBusEn1 X UPP RF-IC Max Unit 1 1.38 1.88 V 0 0 0.4 V Load Resistance 10 20 pF Timing Accuracy ¼ symbo l 1 1.38 1.88 V 0 0 0.4 V Load Resistance 10 20 pF Timing Accuracy ¼ symbo l 1 1.38 1.
RM-258; RM-259 System Module Signal name From To Para-meter Input characteristics Min RFBusDa RFBusClk GENIO3 UPP / RF-IC UPP UEMCLit e RFIC/ UPP RF IC RF IC Typ UEMCLit e RF IC 1.38 1.88 V 0 0 0.4 V Load resistance 10 kW Load capacitanc e 20 pF Data frequency 13 MHz 1 1.38 1.88 V 0 0 0.4 V Load resistance 10 kW Load capacitanc e 20 pF Data frequency 13 MHz 1 2.
RM-258; RM-259 System Module Analogue Signals Table 11 AC and DC Characteristics of RF-Base band Analogue Signals Signal name RFCLK From VCTCXO To Parameter UPP Min Frequency Typ 13/26 Signal amplitude 0.2 Input Impedance 10 0.8 200 Duty Cycle 40 60 RF-IC UEMCL ite Voltage swing (static) 1.4 1.35 TXIN, TXQP, TXQN DC level 1.3 I/Q amplitude mismatch % V System Clock slicer Ref GND, not separated from pwb GND layer 1.45 Vpp 1.
RM-258; RM-259 System Module Signal name AFC From To Parameter UEMCLit e VCTCX O Voltage Min 0.0 0.1 Max 2.4 2.55 (AFCOUT ) Min Resolution Load resistance UEMCLit e RF-IC 11 100 nF Source Impedance 200 W 10 Max PATEMP RF-IC UEMCL ite UEMCL ite Automatic Frequency Control signal for VCTCXO Programmable MW Path powered down 0.1 V 200 W Transmitter power level and ramping control, Ref UEMCLite RF converter specification 2.
RM-258; RM-259 System Module Figure 112 Keyboard schematics The layout is shown in Keyboard layout in UI side. Page 6 –16 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 System Module Figure 113 Keyboard layout in UI side SIM interface The UEMCLite contains the SIM interface logic level shifting. The SIM interface can be programmed to support 3V and 1.8V SIMs. SIM supply voltage is selected by with register in the UEMCLite. It is only allowed to change the SIM supply voltage when the SIM IF is powered down. The SIM power up/down sequence is generated in the UEMCLite. This means that the UEMCLite generates the RST signal to the SIM.
RM-258; RM-259 System Module Pin Name Parameter Min 6 GND GND 0 Typ Max Unit 0 V Notes Ground VSIM specified in regulator section in this document Figure 114 SIM interface block diagram External signals and connections Table 13 System connector Signal XMICP From HS/HF Mic To UEMC Lite HS/HF XEARN EAR/ Amp. INT HEADINT Switch Page 6 –18 Nom 2/60m V diff Max Condi-tion Note Analog audio in Headset Mic bias and audio signal 2mV nominal. HF Mic signal 60mV nominal.
RM-258; RM-259 System Module Signal From To VCHARIN Charger UEMC Lite Min Nom Max 11.1Vp eak 16.9 Vpeak Condi-tion Standard Note Vch from Charger Connector, max 20V 7.9 VRMS 1.0 Apeak 7.0 VRMS 8.4 VRMS 9.2 VRMS Fast charger 850 mA GND GND GND from/to Charger connector Battery connector Table 14 Battery IF Signal From GND Global To Min Nom Max Batt (-) Note Global GND VBAT Batt (+) 3.1 5.1 Battery Voltage BSI UEMCLite 0 2.
RM-258; RM-259 System Module Signal name Pin number Function BSI 3 Battery capacity measurement (fixed resistor inside the battery pack) VBAT 1 Positive battery terminal PWB outline Figure 116 PWB top side component placement Page 6 –20 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 System Module Figure 117 Keyboard layout in UI side RF description Frequency band, power and multi-slot class The requirement leads to the specification in the table below: Table 16 Frequency bands and TX power class System GSM900 Frequency band Tx: 880 – 915 MHz TX power class 4 (33dBm) Rx: 925 – 960 MHz GSM1800 Tx: 1710 – 1785 MHz 1 (30dBm) Rx: 1805 – 1880 MHz Table 17 Multi-slot class Multislot Class GPRS MSC 10 (4Dn/2Up), sum=5 E-GPRS MSC 6 in DL, max.
RM-258; RM-259 System Module The two control methods used are open-loop Vcc control (RFMD) and feedback control with current sensing. The reference waveform (TXC) for the control loop comes from the baseband. The output of the PA goes into a low pass filter located inside the FEM (Front End Module). Finally the transmit signal goes through the band selection and TX/RX switches to the antenna port.
RM-258; RM-259 System Module The next block is a programmable gain amplifier (PGA), which has the second DC-offset compensation block around it. The DC-offset compensation method is again based on digital successive approximation technique. The last block in the analog receiver is an output buffer amplifier, which feeds the differential I/Q signals offchip to be A/D converted in the digital baseband.
RM-258; RM-259 System Module (This page left intentionally blank.) Page 6 –24 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
Nokia Customer Care Glossary Issue 1 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Glossary (This page left intentionally blank.) Page Glossary–2 COMPANY CONFIDENTIAL Copyright © 2007 Nokia. All rights reserved.
RM-258; RM-259 Glossary A/D-converter Analog-to-digital converter ACI Accessory Control Interface ADC Analog-to-digital converter ADSP Application DPS (expected to run high level tasks) AGC Automatic gain control (maintains volume) ALS Ambient light sensor AMSL After Market Service Leader ARM Advanced RISC Machines ARPU Average revenue per user (per month or per year) ASIC Application Specific Integrated Circuit ASIP Application Specific Interface Protector B2B Board to board, connect
RM-258; RM-259 Glossary DPLL Digital Phase Locked Loop DSP Digital Signal Processor DtoS Differential to Single ended EDGE Enhanced data rates for global/GSM evaluation EGSM Extended GSM EM Energy management EMC Electromagnetic compability EMI Electromagnetic interference ESD Electrostatic discharge FCI Functional cover interface FPS Flash Programming Tool FR Full rate FSTN Film compensated super twisted nematic GMSK Gaussian Minimum Shift Keying GND Ground, conductive mass GPI
RM-258; RM-259 Glossary LED Light-emitting diode LPRF Low Power Radio Frequency MCU Micro Controller Unit (microprocessor) MCU Multiport control unit MIC, mic Microphone MIDP Mobile Information Device Profile MIN Mobile identification number MIPS Million instructions per second MMC Multimedia card MMS Multimedia messaging service NTC Negative temperature coefficient, temperature sensitive resistor used as a temperature sensor OMA Object management architechture OMAP Operations, main
RM-258; RM-259 Glossary RX Radio Receiver SARAM Single Access RAM SAW filter Surface Acoustic Wave filter SDRAM Synchronous Dynamic Random Access Memory SID Security ID SIM Subscriber Identity Module SMPS Switched Mode Power Supply SNR Signal-to-noice ratio SPR Standard Product requirements SRAM Static random access memory STI Serial Trace Interface SW Software SWIM Subscriber/Wallet Identification Module TCXO Temperature controlled Oscillator Tiku Finnish for Chip, Successor of
