Nokia Customer Care SERVICE MANUAL [NMP Part No. 9230246] RH-53/54 NOKIA 2650 Mobile Terminal COMPANY CONFIDENTIAL ISSUE 2 06/2005 Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care Amendment Record Sheet Amendment No 2 Date Inserted By Comments 09/2004 TSa Issue 1 06/2005 J Bryman Issue 2 Changes made: Product codes removed Parts: Added updated lists; “Mechanical parts” and “Component parts” Service software: Redundant information removed Troubleshooting: Updated “Phone is dead” and “Phone does not stay on or is jammed” Schematics: Updated with new build Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care Copyright © 2005 Nokia. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia, Nokia Connecting People, X and Y are trademarks or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners. Nokia operates a policy of continuous development.
Nokia Customer Care Warnings and Cautions Please refer to the product’s user guide for instructions relating to operation, care and maintenance including important safety information. Note also the following: Warnings: 1. IF THE DEVICE CAN BE INSTALLED IN A VEHICLE, CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND ANTI-SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION.
Nokia Customer Care For your safety QUALIFIED SERVICE Only qualified personnel may install or repair phone equipment. ACCESSORIES AND BATTERIES Use only approved accessories and batteries. Do not connect incompatible products. CONNECTING TO OTHER DEVICES When connecting to any other device, read its user’s guide for detailed safety instructions. Do not connect incompatible products.
Nokia Customer Care Battery information Note that a new battery's full performance is achieved only after two or three complete charge and discharge cycles! The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery. Use only batteries approved by the phone manufacturer and recharge the battery only with the chargers approved by the manufacturer.
Nokia Customer Care Care and maintenance The product is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. Keep the phone and all its parts and accessories out of the reach of small children. Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits.
Nokia Customer Care Company Policy Our policy is of continuous development; details of all technical modifications will be included with service bulletins. While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing.
Nokia Customer Care Table of Contents RH-53/54, Nokia 2650 Section 1: Front and Introduction Section 2: General Information Section 3: Parts Lists and Component Layouts Section 4: Service Software Instructions Section 5: Service Tools Section 6: Disassembly and Assembly Instructions Section 7: Troubleshooting Instructions Section 8: System Module Section 9: Schematics Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
Introduction to Issue 2 This is the updated issue of the RH-53/54 service manual. The sections of the manual that have been changed are presented in the Amendment record sheet. However, some changes worth mentioning are: ■ Flash memory There have been some errors related to the flash memory (D450). When the phone is dead or jammed, the flash memory is oftentimes the problem. For more information, please refer to the baseband troubleshooting sections "Phone is dead" or "Phone does not stay on or is jammed".
Nokia Customer Care RH-53/54 2-General Information Issue 2 06/2005 Copyright 2005 Nokia. All rights reserved.
RH-53/54 Nokia Customer Care 2-General Information [This page left intentionally blank] 2 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 2-General Information Nokia Customer Care Table of Contents Page No General Information about RH-53/54 ................................................................. 5 Basic transceiver RH-53/54 (Nokia 2650/2651)................................................. 6 Nokia 2650 Eur/Afr/APAC ................................................................................ 6 Nokia 2651 USA ..............................................................................................
RH-53/54 Nokia Customer Care 2-General Information [This page left intentionally blank] 4 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 2-General Information Nokia Customer Care General Information about RH-53/54 RH-53/54 is based on a common phone platform with a colour display. The RH-53 900/ 1800MHz (EU, APAC) and RH/54 850/1900MHz (US) operate on dual-band GSM or EGSM networks. RH-53/54 basic products and modules are listed below.
RH-53/54 Nokia Customer Care 2-General Information ■ Basic transceiver RH-53/54 (Nokia 2650/2651) Nokia 2650 Eur/Afr/APAC Technical type RH-53 for Europe/Africa and APAC/LTA Name Type code Basic handportable Parts list RH-53 Engine module BOM-1 Engine module BOM-2 Mechanics assembly parts RH-53 Swap phones Area/Country SWAP ENGINE FRANCE RED SWAP ENGINE FRANCE SILVER SWAP ENGINE FRANCE BROWN SWAP ENGINE S-AFRICA RED SWAP ENGINE S-AFRICA BROWN SWAP ENGINE S-AFRICA SILVER SWAP ENGINE UKRAINE SILV
RH-53/54 2-General Information Nokia Customer Care Area/Country SWAP ENGINE GREECE SILVER SWAP ENGINE ISRAEL RED SWAP ENGINE GREECE RED SWAP ENGINE GREECE BROWN SWAP ENGINE GULF SILVER SWAP ENGINE GULF RED SWAP ENGINE GULF BROWN Nokia 2651 USA Technical type RH-54 for the North America Name Basic handportable Type code RH-54 Engine module Mechanical assembly Issue 2 06/2005 Parts list BOM-1 RH-54 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 2-General Information Accessories List Batteries Battery 760mAH Li-Ion Chargers BL-4C Type Travel Charger AC-1E Travel Charger AC-1X Travel Charger AC-1U Travel Charger AC-1R Travel Charger AC-1A Travel Charger AC-1AR AC Travel Charger ACP-7E AC Travel Charger ACP-7U AC Travel Charger ACP-7C AC Travel Charger ACP-7X AC Travel Charger ACP-7H AC Travel Charger ACP-7A Performance Travel Charger (EUR) ACP-8E Performance Travel Charger (Korea) ACP-8K P
RH-53/54 2-General Information Nokia Customer Care Travel Charger ACP-12AR Retractable Travel Charger AC-1 Audio Type Boom headset HDB-5 Headset HDC-5 Mobile Inductive Loopset LPS-3 Headset HDE-2 Dual Mono Headset HS-7 HDA-9 TTY Adapter(for 2651 only) HDA-9 Car accessories: Type Plug-in HF Car Kit PPH-1 Microphone HFM-8 Mobile Charger LCH-9 Mobile charger LCH-12 Personal accessories: Type Carrying cases Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia.
RH-53/54 Nokia Customer Care 2-General Information Technical Specifications ■ General specifications of transceiver Dimensions (mm) (L x W x T) Unit Transceiver with BL-4C 760mAh Li-Ion battery pack Parameter Cellular System 86mm x 43,8mm (ends) and 46mm (middle) x 22.
RH-53/54 2-General Information Nokia Customer Care Transmitter output power Frequency band Value RH-53: GSM900, EGSM900 32.5dBm GSM1800 28.5dBm RH-54: GSM850 32.5dBm GSM1900 28.5dBm Environmental conditions Environmental condition Ambient temperature Notes Normal operation -10 oC ... +55 oC Specifications fulfilled Reduced performance +55 oC ... +65 oC Operational only for short periods Intermittent operation -20 oC ... -10 oC and +65 oC ...
RH-53/54 Nokia Customer Care 2-General Information ■ Transceiver features Hardware characteristics • FR, EFR, HR, AMR· • 128x128 pixel high resolution color display· • Jack 4.4 UI· • 4-way scroll & 2 softkeys· • Silicone keymat with white pearl paint· • Fold phone with internal antenna· • Charger plug & headset connector· • Built-in vibrator POWER MANAGEMENT BL-4C: • Capacity (mAh) 760 • Talk time180 min • Stand-by300 hr 12 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care RH-53/54 3-Parts Lists and Component Layouts Issue 2 06/2005 Copyright 2005 Nokia. All rights Reserved.
RH-53/54 Nokia Customer Care 3-Parts Lists and Component Layouts [This page left intentionally blank] 2 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care Table of Contents Page No RH-53/54 Exploded Diagram .............................................................................. 5 Mechanical Parts List , updated edition............................................................ 7 Swap units ........................................................................................................... 9 Component Parts Lists ...................................................................
RH-53/54 Nokia Customer Care 3-Parts Lists and Component Layouts [This page left intentionally blank] 4 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care RH-53/54 Exploded Diagram Figure 1: Exploded view of RH-53/54 Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 3-Parts Lists and Component Layouts Figure 2:Assembly picture 6 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care Mechanical Parts List , updated edition EMEA APAC CHINA LTA NAM Note: For the latest parts lists and for product codes, always refer to the Service bulletins. I001 PT-SCREW 1.8X5.3 REMFORM T6+ YEL ● ● ● ● ● I002 LCD 130X130 CSTN 4K PHILIPS (CITI ● ● ● ● ● I002 LCD LPH8779-1/**80-1 130X130 CSTN 4K COL ● ● ● ● ● I002 LCD MOD 130X130 4KCO CSTN SAMSUNG S9.
RH-53/54 APAC CHINA LTA NAM I101 A-FACE ASSY STROKE DMC08142 HDC15 ● ● ● ● ● I101 A-FACE ASSY BOPOMOFO DMC08142 HDC15 ● ● ● ● ● I101 A-FACE ASSY VIETNAMESE DMC08142 HDC15 ● ● ● ● ● I101 A-FACE ASSY Latin ● ● ● ● ● I103 HINGE ASSY ● ● ● ● ● I104 BACKPLATE ADHESIVE HDC15 (100 pcs) ● ● ● ● ● I104 BACKPLATE ADHESIVE HDC15 (8K pcs) ● ● ● ● ● I105 BACKPLATE PAINT BROWN HDC15 ● ● ● ● ● I105 BACKPLATE PAINT RED HDC15 (N2650 only) ● ● ● ● I105 BACKP
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care Swap units Note: For the latest parts lists and for product codes, always refer to the Service bulletins Swap Units EMEA RH-53 N2650 SWAP ENGINE E&A BROWN ● RH-53 N2650 SWAP ENGINE E&A RED ● RH-53 N2650 SWAP ENGINE E&A SILVER ● RH-53 N2650 SWAP ENGINE RUSSIA BROWN ● RH-53 N2650 SWAP ENGINE RUSSIA RED ● RH-53 N2650 SWAP ENGINE RUSSIA SILVER ● RH-53 N2650 SWAP ENGINE TURKEY BROWN ● RH-53 N2650 SWAP ENGINE TURKEY RED ● RH-53
RH-53/54 Nokia Customer Care 3-Parts Lists and Component Layouts Component Parts Lists ■ Component parts list for RH-53, original edition Note: For the latest parts lists and for product codes, always refer to the Service bulletins Item Side X/Y Description Value B200 T J5 CRYSTAL 32.768KHZ+-30PPM 9PF 32.768kHz B600 T D6 CRYSTAL 26.OMHZ+-10PPM 15.
RH-53/54 3-Parts Lists and Component Layouts Item Side X/Y Nokia Customer Care Description Value C184 T D5 CHIPCAP NP0 56P J 50V 0402 56p C185 T D5 CHIPCAP NP0 56P J 50V 0402 56p C186 T F5 CHIPCAP X7R 330P J 50V 0402 330p C200 T H5 CHIPCAP X5R 100N K 10V 0402 100n C201 T H4 CHIPCAP X5R 1U K 6V3 0603 1u0 C202 T H4 CHIPCAP X7R 10N K 16V 0402 10n C203 T J2 CHIPCAP X5R 1U K 6V3 0603 1u0 C205 T I5 CHIPCAP X5R 1U K 6V3 0603 1u0 C206 T I5 CHIPCAP X5R 1U K 6
RH-53/54 Nokia Customer Care Item Side X/Y 3-Parts Lists and Component Layouts Description Value C235 T J4 CHIPCAP X5R 1U K 6V3 C236 T G2 CHIPCAP X5R 100N K 10V 0402 100n C237 T I4 CHIPCAP X5R 100N K 10V 0402 100n C238 T H4 CHIPCAP X5R 100N K 10V 0402 100n C239 T I2 CHIPCAP X5R 100N K 10V 0402 100n C240 T J2 CHIPCAP X7R 10N K 16V 0402 10n C243 T J3 CHIPCAP X5R 1U K 6V3 0603 1u0 C244 T J2 CHIPCAP X5R 1U K 6V3 0603 1u0 C260 T G5 CHIPCAP X5R 1U K 6V3 060
RH-53/54 3-Parts Lists and Component Layouts Item Side X/Y Nokia Customer Care Description Value C451 T D2 CHIPCAP X5R 100N K 10V 0402 100n C452 T B2 CHIPCAP X5R 100N K 10V 0402 100n C454 T C4 CHIPCAP X7R 100N K 16V 0603 100n C607 T G6 CHIPCAP NP0 1P2 C 50V 0402 1p2 C610 T F6 CHIPCAP X5R 100N K 10V 0402 100n C614 T E7 CHIPCAP X5R 100N K 10V 0402 100n C616 T D7 CHIPCAP X5R 1U K 6V3 C617 T F8 CHIPCAP X5R 100N K 10V 0402 100n C618 T F6 CHIPCAP X5R 100N K
RH-53/54 Nokia Customer Care Item Side X/Y 3-Parts Lists and Component Layouts Description Value C704 T H7 CHIPCAP X5R 2U2 K 10V 0805 2u2 C707 T I8 CHIPCAP NP0 10P J 50V 0402 10p C708 T H6 CHIPCAP NP0 33P J 50V 0402 33p C709 T H8 CHIPCAP NP0 10P J 50V 0402 10p C711 T J8 CHIPCAP X5R 2U2 K 10V 0805 2u2 C727 T H6 CHIPCAP NP0 3P3 C 50V 0402 3p3 C728 T J7 CHIPCAP NP0 3P3 C 50V 0402 3p3 C729 T J6 CHIPCAP NP0 1P0 C 50V 0402 1p0 C730 T J6 CHIPCAP NP0 10P J 5
RH-53/54 3-Parts Lists and Component Layouts Item Side X/Y Nokia Customer Care Description Value L612 T G7 CHIP COIL 3N3 +-0N3 Q28/800M 0402 3n3H L613 T G7 CHIP COIL 3N3 +-0N3 Q28/800M 0402 3n3H L614 T C8 CHIP COIL 3N3 +-0N3 Q28/800M 0402 3n3H L703 T J7 FERR.BEAD 0R03 42R/100MHZ 3A 0805 42R/100MHz N180 T E5 AF AMP 0.
RH-53/54 Nokia Customer Care Item Side X/Y 3-Parts Lists and Component Layouts Description Value R200 T H5 CHIPRES 0W5 0R22 J 200PPM R202 T K2 RES NETWORK 0W03 4X100K J R205 T J3 CHIPRES 0W06 470R J R206 T J2 CHIPRES 0W06 4K7 J 0402 4k7 R207 T K2 CHIPRES 0W06 4K7 J 0402 4k7 R306 T K5 CHIPRES 0W06 27R J 0402 27R R307 T I2 CHIPRES 0W06 10K J 0402 10k R313 T B8 CHIPRES 0W06 27R J 0402 27R R316 T C2 CHIPRES 0W06 10K J 0402 10k R420 T E6 CHIPRES 0W06 1K0
RH-53/54 3-Parts Lists and Component Layouts Item Side X/Y Nokia Customer Care Description Value R648 T F8 CHIPRES 0W06 120R J 0402 120R R655 T E8 CHIPRES 0W06 330R J 0402 330R R657 T G8 CHIPRES 0W06 18R J 0402 18R R658 T G8 CHIPRES 0W06 18R J 0402 18R R705 T I8 CHIPRES 0W06 8K2 J 0402 8k2 R711 T J8 RES NETWORK 0W04 2DB ATT R712 T I8 CHIPRES 0W06 100R J R713 T I8 CHIPRES JUMPER 0R0 R714 T H8 RES NETWORK 0W04 2DB ATT R715 T J7 CHIPRES 0W06 10R J 0402
RH-53/54 Nokia Customer Care 3-Parts Lists and Component Layouts ■ Component parts list for RH-53, updated edition EMEA APAC CHINA LTA NAM Note: For the latest parts lists and for product codes, always refer to the Service bulletins T H5 ● ● ● ● ● 0402 T I8 ● ● ● ● ● CHIPRES JUMPER 0R0 0402 B A5 ● ● ● ● ● R309 CHIPRES JUMPER 0R0 0402 B B5 ● ● ● ● ● R308 CHIPRES JUMPER 0R0 0402 B B5 ● ● ● ● ● R715 CHIPRES 0W06 10R J 0402 T J7 ● ● ● ● ● R716 CHIP
RH-53/54 APAC CHINA LTA NAM Nokia Customer Care EMEA 3-Parts Lists and Component Layouts R206 CHIPRES 0W06 4K7 J 0402 T J2 ● ● ● ● ● R207 CHIPRES 0W06 4K7 J 0402 T K2 ● ● ● ● ● R623 CHIPRES 0W06 6K8 J 0402 T E8 ● ● ● ● ● R316 CHIPRES 0W06 10K J 0402 T C2 ● ● ● ● ● R154 CHIPRES 0W06 10K J 0402 T K3 ● ● ● ● ● R307 CHIPRES 0W06 10K J 0402 T I2 ● ● ● ● ● R620 CHIPRES 0W06 12K J 0402 T G6 ● ● ● ● ● R629 CHIPRES 0W06 18K J 0402 T F6
RH-53/54 APAC CHINA LTA NAM 3-Parts Lists and Component Layouts EMEA Nokia Customer Care R157 RES NETWORK 0W06 2X2K2 J 0404 T K4 ● ● ● ● ● R640 RES NETWORK 0W04 2DB ATT 0404 T D7 ● ● ● ● ● R711 RES NETWORK 0W04 2DB ATT 0404 T J8 ● ● ● ● ● R714 RES NETWORK 0W04 2DB ATT 0404 T H8 ● ● ● ● ● R100 NTC RES 0W1 47K J B 4050+-3% 0402 T C6 ● ● ● ● ● C640 CHIPCAP NP0 3N9 J 25V 0805 T E8 ● ● ● ● ● C310 CHIPCAP X5R 2U2 K 10V 0805 T B8 ● ● ● ● ●
RH-53/54 APAC CHINA LTA NAM Nokia Customer Care EMEA 3-Parts Lists and Component Layouts C234 CHIPCAP X5R 1U K 6V3 0603 T G3 ● ● ● ● ● C207 CHIPCAP X5R 1U K 6V3 0603 T J2 ● ● ● ● ● C244 CHIPCAP X5R 1U K 6V3 0603 T J2 ● ● ● ● ● C243 CHIPCAP X5R 1U K 6V3 0603 T J3 ● ● ● ● ● C224 CHIPCAP X5R 1U K 6V3 0603 T F4 ● ● ● ● ● C263 CHIPCAP X5R 1U K 6V3 0603 T I5 ● ● ● ● ● C211 CHIPCAP X5R 1U K 6V3 0603 T I5 ● ● ● ● ● C229 CHIPCAP X5R 1U K
RH-53/54 APAC CHINA LTA NAM 3-Parts Lists and Component Layouts EMEA Nokia Customer Care C313 CHIPCAP NP0 27P J 50V 0402 B A5 ● ● ● ● ● C314 CHIPCAP NP0 27P J 50V 0402 B A4 ● ● ● ● ● C315 CHIPCAP NP0 27P J 50V 0402 B B5 ● ● ● ● ● C319 CHIPCAP NP0 27P J 50V 0402 T C2 ● ● ● ● ● C321 CHIPCAP NP0 27P J 50V 0402 B A5 ● ● ● ● ● C320 CHIPCAP NP0 27P J 50V 0402 B A5 ● ● ● ● ● C318 CHIPCAP NP0 27P J 50V 0402 T D5 ● ● ● ● ● C317 CHIPCAP NP
RH-53/54 APAC CHINA LTA NAM Nokia Customer Care EMEA 3-Parts Lists and Component Layouts C636 CHIPCAP X7R 1N0 K 50V 0402 T F6 ● ● ● ● ● C100 CHIPCAP X7R 6N8 K 25V 0402 T L5 ● ● ● ● ● C106 CHIPCAP X7R 10N K 16V 0402 B M2 ● ● ● ● ● C240 CHIPCAP X7R 10N K 16V 0402 T J2 ● ● ● ● ● C123 CHIPCAP X7R 10N K 16V 0402 B M4 ● ● ● ● ● C405 CHIPCAP X7R 10N K 16V 0402 T D4 ● ● ● ● ● C450 CHIPCAP X7R 10N K 16V 0402 T C2 ● ● ● ● ● C404 CHIPCAP X7
RH-53/54 APAC CHINA LTA NAM 3-Parts Lists and Component Layouts EMEA Nokia Customer Care C614 CHIPCAP X5R 100N K 10V 0402 T E7 ● ● ● ● ● C637 CHIPCAP X5R 100N K 10V 0402 T G8 ● ● ● ● ● C236 CHIPCAP X5R 100N K 10V 0402 T G2 ● ● ● ● ● C451 CHIPCAP X5R 100N K 10V 0402 T D2 ● ● ● ● ● C634 CHIPCAP X5R 100N K 10V 0402 T E8 ● ● ● ● ● C237 CHIPCAP X5R 100N K 10V 0402 T I4 ● ● ● ● ● C239 CHIPCAP X5R 100N K 10V 0402 T I2 ● ● ● ● ● C200 CHI
RH-53/54 Description Side APAC CHINA LTA NAM Nokia Customer Care EMEA 3-Parts Lists and Component Layouts L614 CHIP COIL 3N3 +-0N3 Q28/800M 0402 T C8 ● ● ● ● ● L610 CHIP COIL 3N3 +-0N3 Q28/800M 0402 T G7 ● ● ● ● ● L612 CHIP COIL 3N3 +-0N3 Q28/800M 0402 T G7 ● ● ● ● ● L605 CHIP COIL 3N9 +-0N3 Q28/800M 0402 T G8 ● ● ● ● ● L606 CHIP COIL 12N J Q31/800MHZ 0402 T G8 ● ● ● ● ● L609 CHIP COIL 18N J Q29/800MHZ 0402 T H8 ● ● ● ● ● L607 CHIP COIL 39N J
RH-53/54 Description Side APAC CHINA LTA NAM 3-Parts Lists and Component Layouts EMEA Nokia Customer Care V303 LED 360-640 MCD SMD2 B B4 ● ● ● ● ● V302 LED 360-640 MCD SMD2 B B6 ● ● ● ● ● V306 LED BLUE 75MCD 20MA 90DEG B M5 ● ● ● ● ● V301 LED BLUE 75MCD 20MA 90DEG B F2 ● ● ● ● ● V300 LED BLUE 75MCD 20MA 90DEG B F8 ● ● ● ● ● F100 SM FUSE F 1.
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care ■ Component parts list for RH-54, original edition Note: For the latest parts lists and for product codes, always refer to the Service bulletins Item Side X/Y Description Value B200 T J5 CRYSTAL 32.768KHZ+-20P B600 T D6 CRYSTAL 26.
RH-53/54 Nokia Customer Care Item Side 3-Parts Lists and Component Layouts X/Y Description Value C186 T F5 CHIPCAP X7R 330P J 50V 330p C200 T H5 CHIPCAP X5R 100N K 10V 100n C201 T H4 CHIPCAP X5R 1U K 6V3 1u0 C202 T H4 CHIPCAP X7R 10N K 16V 10n C203 T J2 CHIPCAP X5R 1U K 6V3 1u0 C205 T I5 CHIPCAP X5R 1U K 6V3 1u0 C206 T I5 CHIPCAP X5R 1U K 6V3 1u0 C207 T J2 CHIPCAP X5R 1U K 6V3 1u0 C208 T F4 CHIPCAP X5R 1U K 6V3 1u0 C209 T J4 CHIPCAP NP0 10P J 50V 10p
RH-53/54 3-Parts Lists and Component Layouts Item Side X/Y Nokia Customer Care Description Value C237 T I4 CHIPCAP X5R 100N K 10V 100n C238 T H4 CHIPCAP X5R 100N K 10V 100n C239 T I2 CHIPCAP X5R 100N K 10V 100n C240 T J2 CHIPCAP X7R 10N K 16V 10n C243 T J3 CHIPCAP X5R 1U K 6V3 1u0 C244 T J2 CHIPCAP X5R 1U K 6V3 1u0 C260 T G5 CHIPCAP X5R 1U K 6V3 1u0 C261 T H5 CHIPCAP X5R 1U K 6V3 1u0 C262 T G4 CHIPCAP X5R 1U K 6V3 1u0 C263 T I5 CHIPCAP X5R 1U K 6V3 1u0
RH-53/54 Nokia Customer Care Item Side 3-Parts Lists and Component Layouts X/Y Description Value C454 T C4 CHIPCAP X7R 100N K 16V 100n C607 T G6 CHIPCAP NP0 1P2 C 50V 1p2 C610 T F6 CHIPCAP X5R 100N K 10V 100n C614 T E7 CHIPCAP X5R 100N K 10V 100n C616 T D7 CHIPCAP X5R 1U K 6V3 1u0 C617 T F8 CHIPCAP X5R 100N K 10V 100n C618 T F6 CHIPCAP X5R 100N K 10V 100n C619 T F6 CHIPCAP NP0 27P J 50V 27p C620 T E6 CHIPCAP X5R 3U3 K 6V3 3u3 C621 T D6 CHIPCAP X5R 100N
RH-53/54 3-Parts Lists and Component Layouts Item Side X/Y Nokia Customer Care Description Value C708 T H6 CHIPCAP NP0 33P J 50V 33p C709 T H8 CHIPCAP NP0 10P J 50V 10p C711 T J8 CHIPCAP X5R 2U2 K 10V 2u2 C727 T H6 CHIPCAP NP0 3P3 C 50V 3p3 C728 T J7 CHIPCAP NP0 3P3 C 50V 3p3 C729 T J6 CHIPCAP NP0 1P0 C 50V 1p0 C730 T J6 CHIPCAP NP0 10P J 50V 10p D200 T I3 UEMK D400 T E3 UPP8M V2.6/2.
RH-53/54 Nokia Customer Care Item Side 3-Parts Lists and Component Layouts X/Y Description Value L614 T C8 CHIP COIL 3N3 +-0N3 Q2 3n3H L703 T J7 FERR.BEAD 0R03 42R/100 42R/100MHz N180 T E5 544_0.675 AF AMP 0.
RH-53/54 3-Parts Lists and Component Layouts Item Side X/Y Nokia Customer Care Description Value R205 T J3 CHIPRES 0W06 470R J 470R R206 T J2 CHIPRES 0W06 4K7 J 4k7 R207 T K2 CHIPRES 0W06 4K7 J 4k7 R306 T K5 CHIPRES 0W06 27R J 27R R307 T I2 CHIPRES 0W06 10K J 10k R313 T B8 CHIPRES 0W06 27R J 27R R316 T C2 CHIPRES 0W06 10K J 10k R420 T E6 CHIPRES 0W06 1K0 J 1k0 R422 T G2 CHIPRES 0W06 27K J 27k R426 T E4 CHIPRES 0W06 1K0 J 1k0 R450 T C4 CHIPRES 0W06
RH-53/54 Nokia Customer Care Item Side 3-Parts Lists and Component Layouts X/Y Description Value R657 T G8 CHIPRES 0W06 18R J 18R R658 T G8 CHIPRES 0W06 18R J 18R R705 T I8 CHIPRES 0W06 8K2 J 8k2 R711 T J8 RES NETWORK 0W04 2DB A 436R/11R6/4 R712 T I8 CHIPRES 0W06 100R J 100R R713 T I8 CHIPRES JUMPER 0R0 0R R714 T H8 RES NETWORK 0W04 2DB A 436R/11R6/4 R715 T J7 CHIPRES 0W06 10R J 10R R716 T H6 CHIPRES 0W06 10R J 10R T600 T G7 TRANSF BALUN 1800+-100 - T
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care ■ Component parts list for RH-54, updated edition Side B200 CRYSTAL 32.768KHZ+-20PPM 12.5PF T J5 ● B200 CRYSTAL 32.768KHZ+-20PPM 12.5PF T J5 ● B600 CRYSTAL 26.OMHZ+-10PPM 15.5PF T D6 ● C100 CHIPCAP X7R 6N8 K 25V 0402 T L5 ● C101 CHIPCAP X7R 10N K 16V 0402 B M6 ● C102 CHIPCAP X7R 10N K 16V 0402 B M6 ● C103 CHIPTCAP 100u 6V3 70mOhm 3.5x2.8x2.
RH-53/54 C185 CHIPCAP NP0 100P J 50V 0402 T D5 ● C186 CHIPCAP X7R 330P J 50V 0402 T F5 ● C200 CHIPCAP X5R 100N K 10V 0402 T H5 ● C201 CHIPCAP X5R 1U K 6V3 0603 T H4 ● C202 CHIPCAP X7R 10N K 16V 0402 T H4 ● C203 CHIPCAP X5R 1U K 6V3 0603 T J2 ● C205 CHIPCAP X5R 1U K 6V3 0603 T I5 ● C206 CHIPCAP X5R 1U K 6V3 0603 T I5 ● C207 CHIPCAP X5R 1U K 6V3 0603 T J2 ● C208 CHIPCAP X5R 1U K 6V3 0603 T F4 ● C209 CHIPCAP NP0 10P J 50V 0402 T J4 ● C210 CHIP
RH-53/54 T J4 ● 0402 T G2 ● CHIPCAP X5R 100N K 10V 0402 T I4 ● C238 CHIPCAP X5R 100N K 10V 0402 T H4 ● C239 CHIPCAP X5R 100N K 10V 0402 T I2 ● C240 CHIPCAP X7R 10N K 16V 0402 T J2 ● C243 CHIPCAP X5R 1U K 6V3 0603 T J3 ● C244 CHIPCAP X5R 1U K 6V3 0603 T J2 ● C260 CHIPCAP X5R 1U K 6V3 0603 T G5 ● C261 CHIPCAP X5R 1U K 6V3 0603 T H5 ● C262 CHIPCAP X5R 1U K 6V3 0603 T G4 ● C263 CHIPCAP X5R 1U K 6V3 0603 T I5 ● C264 CHIPCAP X5R 1U K 6V3 0603 T
RH-53/54 C451 CHIPCAP X5R 100N K 10V 0402 T D2 ● C452 CHIPCAP X5R 100N K 10V 0402 T B2 ● C454 CHIPCAP X7R 100N K 16V 0603 T C4 ● C607 CHIPCAP NP0 1P2 C 50V 0402 T G6 ● C610 CHIPCAP X5R 100N K 10V 0402 T F6 ● C614 CHIPCAP X5R 100N K 10V 0402 T E7 ● C616 CHIPCAP X5R 1U K 6V3 T D7 ● C618 CHIPCAP X5R 100N K 10V T F6 ● C619 CHIPCAP NP0 27P J 50V 0402 T F6 ● C620 CHIPCAP X5R 3U3 K 6V3 0805 T E6 ● C624 CHIPCAP X5R 1U K 6V3 0603 T D8 ● C625 CHIPCAP N
RH-53/54 C727 CHIPCAP NP0 3P3 C 50V 0402 T H6 ● C728 CHIPCAP NP0 3P3 C 50V 0402 T J7 ● C729 CHIPCAP NP0 1P0 B 50V 0402 T J6 ● C730 CHIPCAP NP0 10P J 50V 0402 T J6 ● D450 FLASH 2MX16 1.8/1.8V VFBGA44 PBFREE T C3 ● D450 FLASH 2MX16 1.8V/1.8V VFGBA44 PBFREE T C3 ● D450 FLASH 2MX16 1.8V/1.8V VFGBA44 PBFREE T C3 ● F100 SM FUSE F 1.5A 32V ROHS-FREE 0603 T L4 ● G600 VCO 3296-3980MHZ 4-BAND Matsushita T D8 ● L100 FERR.
RH-53/54 Side N180 AF AMP 0.4W LM4890/NCP2890 PB-FREE T E5 ● N303 DC/DC CONV TK65600 USMD8 T B8 ● N306 HALL IC SWITCH SH248CSP VCC T E1 ● N306 HALL IC SWITCH SH248CSP VCC T E1 ● N306 HALL IC SWITCH SH248CSP VCC T E1 ● N600 Mjolner RF ASIC PMB3347 LFLGA80 F7 T F7 ● N600 Mjolner RF ASIC PMB3347 LFLGA80 F7 MCT T F7 ● N700 PW AMP FEM GSM900/1800/1900 3.
RH-53/54 T J3 ● 0402 T J2 ● CHIPRES 0W06 4K7 J 0402 T K2 ● R306 CHIPRES 0W06 56R J 0402 T K5 ● R307 CHIPRES 0W06 10K J 0402 T I2 ● R313 CHIPRES 0W06 27R J 0402 T B8 ● R316 CHIPRES 0W06 10K J 0402 T C2 ● R420 CHIPRES 0W06 1K0 J 0402 T E6 ● R422 CHIPRES 0W06 27K J 0402 T G2 ● R426 CHIPRES 0W06 1K0 J 0402 T E4 ● R450 CHIPRES 0W06 4K7 J 0402 T C4 ● R603 CHIPRES 0W06 100R J 0402 T D7 ● R605 CHIPRES 0W06 22R J 0402 T F6 ● R607 CHIPRES 0W06
RH-53/54 T J8 ● T I8 ● T I8 ● T H8 ● 0402 T J7 ● 0402 T H6 ● TRANSF BALUN 1800+-100MHZ 2X1.
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care Component Layouts RH-53/54 Figure 3:RH-53/54 layout, top Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 3-Parts Lists and Component Layouts Figure 4:RH-53/54 layout, bottom 44 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 3-Parts Lists and Component Layouts Nokia Customer Care [This page left intentionally blank] Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care RH-75 Series Cellular Phones Service Software Instructions Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care [This page left intentionally blank] Page 2 2005 Nokia Corporation.
Company Confidential RH-75 Nokia Customer Care Quick guide for Phoenix Service SW installation............................................................................ 5 Phoenix installation steps in brief ................................................................................................... 5 Phoenix Service SW ................................................................................................................................. 7 Before installation ............................
RH-75 Company Confidential Nokia Customer Care Module Jig flash concept .................................................................................................................62 JBV-1 flash concept ...........................................................................................................................64 Page 4 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Quick guide for Phoenix Service SW installation Phoenix installation steps in brief These are the basic steps to install the Phoenix • Connect a DK2 dongle or FLS-4S POS Flash Device • Install the Phoenix Service SW • Install the data package for Phoenix • Configure users • Manage connection settings (depends on the tools you are using) • Phoenix is now ready for FLS-4S Point Of Sales flash device use.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Separate installation packages for flash update files and drivers are also available, but it is not necessary to use them unless updates appear between Phoenix Service SW releases. If separate update packages are used, they should be used after Phoenix and data packages have been installed.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Phoenix Service SW Note: File names and screen shots are examples only. The name and the type designator may not be correct. Before installation • Check that a Dongle is attached to the parallel port of your computer. • Download the installation package (e.g. phoenix_service_sw_a10_2003_33_5_22.exe) to your computer (e.g. C:\TEMP). • Close all other programs. • Run the application file (e.g.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Click "Next" in Welcome dialog to continue. Choose destination folder, it is recommended to use the default folder C:\ProgramFiles\Nokia\Phoenix. Choose “Next” to continue. You may choose another location by selecting “Browse” (not recommended) Page 8 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Setup copies the components, progress of the setup is shown. Please wait. Drivers will be installed and updated, please wait.. the process may take several minutes Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care to complete. If the operating system does not require rebooting (Windows 2000, XP) the PC components are registered right away. Click "Finish" to finalize. Phoenix is ready for use. Page 10 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions If the operating system used requires restarting your computer (Windows 98, SE, ME) the Install Shield Wizard will tell you about it. Select "Yes..." to reboot the PC immediately and "No..." to reboot the PC manually afterwards. After the reboot components are registered and Phoenix is ready for use. Note that Phoenix doesn't work, if components are not registered. Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Now the installation of Phoenix Service SW is ready and it can be used after: • installing Phone model specific Phone Data Package for Phoenix • configuring users and connections FLS-4S can be used right away. FPS-8* can be used after updating Flash Update Package files to it. If reboot is not needed components are registered after copying them. If restarting of your computer is not needed, Click "Finish" to exit the setup.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Update installation of Phoenix If you already have the Phoenix Service SW installed on your computer, sooner or later there will be need to update it when new versions are released. Always use the latest available versions of both the Phoenix Service SW and the Phone Specific Data Package . Instructions can be found in phone model specific Technical Bulletins and Phone data package readme.txt files (shown during installation).
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Uninstalling Phoenix Uninstallation can be done manually from Windows Control Panel - Add / Remove Programs. Choose “Phoenix Service Software” and click "Add/Remove". Choose “Remove” to uninstall Progress of the uninstallation is shown. Page 14 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions If the operating system does not require rebooting, select “Finish” to complete. If the operating system used requires rebooting, Install Shield Wizard will tell you about it. Select "Yes..." to reboot the PC immediately and "No..." to reboot the PC manually afterwards. Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Repair If you experience any problems with service software or suspect that files have been lost, you can use the repair – function before completely reinstalling Phoenix. Note that the original installation package (e.g. phoenix_service_sw_a10_2003_33_5_22.exe ) must be found on your PC when you run the repair setup. Run Windows Control Panel - Add / Remove Programs, choose “Phoenix Service Software” and click "Add/Remove".
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Data package for Phoenix (product specific) Before installation Product data package contains all product specific data to make the Phoenix Service Software and tools usable with a certain phone model. It also includes the latest version of flash update package for FLS-4S* and FPS-8*. • Check that the dongle is attached to the parallel port of your computer. • Install Phoenix Service SW.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Choose “Next” to continue. From this view you can see the contents of the Data Package. Read the text carefully. There should be information about the Phoenix version needed with this data package. Choose “Next”. Confirm location and choose “Next” to continue. Install Shield checks where the Phoenix application is installed and the directory is Page 18 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions shown. Choose “Next” to continue. Choose “Next” to start copying the files. Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Phone model specific files will be installed. Please wait. Choose “Finish” to complete installation. You now have all phone model specific files installed in your Phoenix Service SW. Now Phoenix can be used to for example flash phones and print type labels after: • configuring users • managing connections FLS-4S can be used right away. FPS-8* can be used after updating Flash Update Package files to it.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Uninstalling Phoenix data package Uninstallation can also be done manually from Windows Control Panel / Add / Remove Programs/“RH-18 Phone Data Package”. If you try to install the same version of Phoenix data package that you already have, you are asked if you want to uninstall the version you have on your PC. Answer “OK” to uninstall, “Cancel” if you don’t want to uninstall.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Configuring users Start Phoenix Service SW and Login. To add new user choose “Edit”. If user ID is already configured, choose your own user ID from the list and choose “OK”. Choose “Add ” to continue. Type in your name and Initials to fields and choose “OK”. Page 22 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions User has now been created, choose “OK”.. You are now able to login with this user name, choose “OK”. Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Managing connections Start Phoenix Service SW and Login. Choose “Manage Connections” From “File” – Menu Existing connections can be selected , edited, deleted and new ones created by using this dialog. A connection can be created either manually or by using a Connection Wizard. To add new connection, choose “Add” and select if you want to create it manually or by using the Wizard. Page 24 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Choose “Next” to continue. In the next dialogs you will be asked to select some settings for the connection. Manual settings A) For FLS-4S POS Flash Device choose following connection settings: Media: FBUS COM Port: Virtual COM Port used by FLS-4S.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Activate the connection you want to use by clicking it and use up/down arrows to move it on top of the list. Choose “Apply”. The connection is now selected and can be used after closing the “Manage Connections” window. Selected connection will be shown on the right hand bottom corner of the screen.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Updating flash support files for FPS-8* and FLS-4S* Before installation Install Phoenix Service SW Install phone model specific data package for Phoenix The flash support files are delivered in the same installation package with Phoenix data packages or newer Phoenix packages beginning from September 2003.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care If you try to downgrade the existing version to older ones, the setup will be aborted. If you really want to downgrade, uninstall newer files manually from Control Panel and then re run the installation again. If an older version exists on your PC and it needs to be updated, Choose “Next” to continue installation. It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia\Phoenix.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Installation continues… Choose “Finish” to complete procedure. • FLS-4S can be used right after Flash Update Package is installed. • FPS-8* must be updated by using Phoenix! Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Updating the FPS-8* flash prommer SW Start Phoenix Service Software Select”FPS-8 / FPS-8C maintenance” from”Flashing” menu. When new FPS-8 flash update package is installed to computer you will be asked to update the files to your FPS-8 prommer. Select”Yes” to update files.. 0 02 Update procedure takes a couple of minutes, please wait until you are notified that update has been successful.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions View after successful prommer software update FPS-8 sw can also be updated by pressing”Update” button and selecting appropriate fps8upd.ini file under C:\Program Files\Nokia\Phoenix\Flash - directory All files can be loaded separately to FPS-8. To do this, just press right mouse button in Flash box files” window and select file type to be loaded. More information and help can be found from the “Help” dialog.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care FPS-8 activation and deactivation • Before the FPS-8 can be successfully used for phone programming, it must be first activated. • If there is a need to send FPS-8 box to somewhere e.g. for repair, box must be first deactivated. Activation Before FPS-8 can be successfully used for phone programming, it must be first activated.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Select “Activate” from the “FPS8/8C Maintenance” – UI. The activation file you saved to C:\ProgramFiles\Nokia\Phoenix\BoxActivation - directory will be shown (e.g. 00000.in), check that it is correct. Box will be activated when you choose “Open”. Turn FPS-8 power off and on to complete activation. Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Deactivation Start Phoenix Service Software. Select ”FPS-8 / FPS-8C maintenance” from ”Flashing” menu. Select “Deactivate” from the “FPS8/8C Maintenance” – UI. Confirm Deactivation by choosing “Yes”, Box will be deactivated. Turn FPS-8 power off and on to complete deactivation. Page 34 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions JBV-1 docking station SW The JBV-1 docking station is a common tool for all DCT-4 generation products. In order to make the JBV-1 usable with different phone models, a phone specific docking station Adapter is used for different service functions. The JBV-1 docking station contains software (firmware) which can be updated.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care Installing SW needed for the JBV-1 SW update Note: DO NOT CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER YET! Run Jbv1_update.zip file and start SW Installation by double clicking Setup.exe. Files needed for JBV-1 package setup program will be extracted. Installation begins, please read the information shown and choose “Next” to continue.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Select “Full” Installation and choose “Next” to continue Program folder will be created. Choose “Next” to continue, Software files will be installed. Issue 2 06/2005 2005 Nokia Corporation.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care After successful installation, choose “Finish” to complete. NOW YOU CAN CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER! Connect power to JBV-1 (11-16V DC) from external power supply, then connect USB Cable between JBV-1 USB connector and PC. Page 38 2005 Nokia Corporation.
Company Confidential Nokia Customer Care RH-75 Service Software Instructions Windows will detect connected USB cable and detect drivers for new HW. Follow the instructions and allow Windows to search and install the best drivers available. After this procedure the actual JBV-1 SW update can begin. Updating the JBV-1 docking station software The next step is to install or update the JBV-1 USB drivers which are delivered with the JBV-1 SW installation package.
RH-75 Company Confidential Service Software Instructions Nokia Customer Care JBV-1 Firmware update starts and shows current status of the JBV-1 connected. If firmware version read from your JBV-1 is not the latest one available (v. 17 or older) , it needs to be updated to version 18 by choosing “Update Firmware”.. To update your JBV-1 to new version 18 choose file JBV1v18.CDE and “Open” Please wait, it takes a while until you can hear a “click” from the JBV-1. The older sw file JBV1v17.
RH-53/54 Nokia Customer Care Service Tool Concept For Baseband Tuning Operations EM calibrations should be carried out in JBV-1 Docking Station equipped with DA-27 Docking Station Adapter. Note: RF tunings must be carried out in MJ-30 module jig, JBV-1. Power to JBV-1 should be supplied from an external DC power supply, not FPS-8 prommer. JBV-1 input voltages: Maximum +16 VDC Nominal input for RF tunings is +12 V DC.
RH-53/54 Nokia Customer Care Baseband Tuning Operations ■ Energy Management Tuning External power supply needed. Energy Management (EM) Calibration is used for calibrating Battery and Charger settings of the phone. Preparation for EM Calibration: - Connect the DC Cable SCB-3 between JBV-1 and Vin of the Phone for Charger calibration. - Connect 12…15 V from the Power Supply to JBV-1. - NOTE! Check that the connection is F-BUS (does not work with M-BUS). Select Tuning => Energy Management Calibration.
RH-53/54 Nokia Customer Care Select “Calibrate” to run the selected calibrations. Limits for Energy Management Calibration: Table 1: Parameter Min.
RH-53/54 Nokia Customer Care ■ LCD Contrast Tuning Extra equipment not needed. This function is used to calibrate the LCD Contrast. Must be done when LCD module is changed and there is considerable difference in the contrast. Select Testing => Display Tune Move the sliders to reach good LCD contrast. Close the ”Display tune” dialog to end tuning. 44 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Receiver Tuning: Quick Guide for Tuning With Phoenix ■ General remarks RF tunings must be performed in the same order as shown in this document. The order of the corresponding menu items in the Service SW may be different. If baseband tunings are needed, they should be completed before the RF tunings. Avoid unnecessary tuning – factory-tuning values are always the most accurate ones. NOTE! RF tunings need to be done ONLY if any RF block component is replaced.
RH-53/54 Nokia Customer Care Service Tool Concept for RF Tuning Operations NOTE! RF tunings need to be done ONLY if any RF block component is replaced. • All RF tuning operations must be carried out in the MJ-36 Module Jig! • Power to MJ-36 must be supplied from an external DC power supply, not FPS-8 prommer • MJ-15 input voltages: Maximum + 5 VDC Nominal input for RF tunings is +4.
RH-53/54 Nokia Customer Care Autotuning Autotune feature is designed to align product’s RF part easier and faster. By this autotune component the product is tuned automatically. The user only needs to press ‘Tune’ and the product’s RF is tuned and results are shown to the user. Component controls all the needed RF equipment (RF generator and TX measuring device) except voltage supplier. NOTE! Automatic tuning is ALWAYS the primary tuning mode. Manual tuning is not recommended.
RH-53/54 Nokia Customer Care Set Loss This is the component for saving RF-losses (of cables and jigs) to file. These loss values are needed when you tune the phone with Phoenix (using Auto-Tune component). When you measure the losses you have to be very careful, because these values affect directly how well the phone is tuned. NOTE! This component is only for Auto-Tune uses. Components are protected by PKD-1CS, PKD-1NS, PKD-1 and PKD-1P dongles using standard TSS protection procedure.
RH-53/54 Nokia Customer Care ■ Environment Hardware requirements: PC with Windows 98/2000/NT Power supply Product specific module jig RF-splitter and -cables RF equipment (only one of each is needed) Tx: Agilent E4406 (VSA series transmitter tester) Agilent E4445 (PSA series transmitter tester) Rohde&Schwarz, FSE-family of Signal Analyzers Rohde&Schwarz, FSIQ-family of Signal Analyzers Rx: Agilent ESG family of RF Signal Generators Rohde&Schwarz, SME-family of Signal Generators Issue 2 06/2005 COMPANY
RH-53/54 Nokia Customer Care Figure 4:Setup environment GPIB addresses are not defined. Component finds the addresses and uses them automatically. If several TX tuning devices are connected, this component uses Agilent (VSA or PSA). In RX side, Agilent has highest priority. Protection Components are protected by PKD-1CS, PKD-1NS, PKD-1 and PKD-1P dongles using standard TSS protection procedure.
RH-53/54 Nokia Customer Care RH-53/54 Manual Alignment with Phoenix ■ Manual alignment with Phoenix The alignment/calibrations are the same in both GSM900/850 and GSM1800/1900 except for the channels and frequencies. Only the procedures for GSM900/GSM1800 are shown. The attenuation values for GSM850 are similar to the ones for GSM900, and the ones for GSM1900 to GSM1800. The difference can be 1-2 dBs. In Phoenix select connection Fbus scan product.
RH-53/54 Nokia Customer Care Figure 5: RX calibration values for GSM900 (and GSM850) Figure 6:RX calibration values for GSM1800 (and GSM1900) Press the OK button, and then the Save&Continue button Follow the description in Phoenix, setting up the signal generator as described 52 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care ■ RX Band Filter Response Compensation This tuning measures the band filters ripple over the bands and the information is used to compensate the RX level reporting. Note: If you have a signal generator with a frequency list option, please perform Autotuning. Select Tuning, RX Band Filter Response Compensation Select Band, for example GSM900 Note: You must first tune the lower band to be able to tune the higer band. You can stop at any time by switching off the menu.
RH-53/54 Nokia Customer Care ■ TX Power tuning Select Tuning, Tx Power Level Tuning Note: You must first tune the lower band to be able to tune the higer band. You can stop at any time by switching off the menu. If the values are outside internal specifications, you can not save them and you will have to leave the tuning without saving.
RH-53/54 Nokia Customer Care Set the spectrum analyzer or GSM tester for the required settings and press “OK” If a GSM tester is used set the TX data type to random, so that the tester can trig on the signal. Figure 10: TX Power Level Tuning values for GSM900 (and GSM850) Figure 11:TX Power Level Tuning values for GSM1800 (and GSM1900) Tune the highlighted values to the wanted power (Use average burst power) Tune the base level to –25dBm When done press Save&Continue.
RH-53/54 Nokia Customer Care ■ I/Q tuning Select Tuning > Tx IQ tuning > TX Data Type “random” for a GSM tester like CMU200 or 1/0 for SPA measuring. CMD55 shows the same as a spectrum analyzer when I/Q tuning is selected. CMU200 shows the carrier and sideband suppression directly as figures in the modulation mode. Press Start Figure 12: GSM900 (and GSM850) Figure 13: GSM1800 (and GSM1900) 56 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Set the spectrum analyzer or GSM tester for the required settings and press “OK” Figure 14: GSM900 (and GSM850) Figure 15: GSM1800 (and GSM1900) Begin tuning with data from selected place. Tune DC offset values to lowest carrier. Use Side arrows or +, - . Tune Amplitude and phase to lowest sideband. When satisfied with the result, press Next. (The sidebands should hardly be visible). Or for CMU200 the supression should be better than –40dBc.
RH-53/54 Nokia Customer Care ■ RF control The purpose is to check the receiver or transmitter without going in call. It works very much like a call, but you have control via the PC, and not via the tester. If you want to tune or calibrate at other channels or levels than the default for that function, you can activate RF control at the same time and change the wanted parameters. If you want to tune at other channels than the default, then you must select it first in RF control and then start the tuning.
RH-53/54 Nokia Customer Care Flashing Setup Instructions ■ FPS-8 flash concept Figure 16:FPS-8 flash concept Item Type Description 1 SF-33 Point Of sales flash loading adapter 2 FLC-2 Power cable 3 XCS-4 Modular cable 4 FPS-8 Flash prommer box sales pack 5 AXP-8, included in FPS-8 sales pack FLS-4S sales package US 6 AXS-4, included in FPS-8 sales pack D9-D9 cable 7 0730090 Software protection key Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Item 60 Type Description 8 ACF-8, included in FPS-8 sales pack AC charger 9 SF-12 SRAM module (3pcs needed inside FPS-8 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care ■ POS (Point of Sale) flash concept Figure 17:POS flash Item Type Description 1 SF-33 Point Of sales flash loading adapter 2 XCS-1 Service cable 3 FLS-4S FLS-4S sales package EMEA 4 FLS-4S FLS-4S sales package APAC 5 FLS-4S FLS-4S sales package US POS flashing can also be used with USB connection. (USB cable can be purchased from shops or suppliers providing PC hardware and accessories). Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia.
RH-53/54 Nokia Customer Care ■ Module Jig flash concept Figure 18:Module jig concept Flashing with MJ-36 is recommended in local mode. The following equipment is needed for RH -53/54 Care (AMS) SW ypdate when the system is placed in the module jig MJ-36 and connected through an FPS-8 set-up.
RH-53/54 Nokia Customer Care Note! More than 32MB SRAM may be required in FPS-8 This concept can also be used for troubleshooting and RF calibration. • MJ-36 is intended for use with an external power supply. • MJ-36 input voltage : normal +6V, maximum +12V • Ensure that the jumper is set open for voltage regulation before the external power supply is connected. • When FPS-8 is used as the power supply (4V), the jumper should be set close to bypass regulator.
RH-53/54 Nokia Customer Care ■ JBV-1 flash concept Figure 19:JBV- flash/service concept Item: Type: Description 1 JBV-1 Docking station 2 DA-27 Docking station adapter 3 XCS-4 Modular cable 4 PCS-1 DC power cable 5 DAU-9S Service FBUS cable 6 AXP-8, included in FPS-8 slaes pack Printer cable 7 AXS-4, included in FPS-8 slaes pack D9-D9 cable, 8 PKD-1 Software protection key 9 SF-12 SRAM module (3pcs needed inside FPS-8) Note! More than 32MB SRAM may be required in FPS-8 This c
Nokia Customer Care RH-53/54 5-Service Tools Issue 2 06/2005 Copyright 2005 Nokia.
RH-53/54 Nokia Customer Care 5-Service Tools [This page left intentionally blank] 2 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 5-Service Tools Nokia Customer Care Table of Contents Page No Service Tools....................................................................................................... 5 Custom Service Tools........................................................................................ 5 Standard service tools ....................................................................................... 7 Service Cables .................................................................................
RH-53/54 Nokia Customer Care 5-Service Tools [This page left intentionally blank] 4 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 5-Service Tools Nokia Customer Care Service Tools ■ Custom Service Tools Product DA-27 Service Tool Photo Description Info Docking Station Adapter The Docking Station Adapter, together with a Docking Station, is used for analysis of Mbus, Fbus, RF, and audio connections. Pack of test 10 test pins to be used with SF-33 and DA-27. Spare lock part for DA-27 Spare lock part for DA-27 MJ-36 Module Jig This jig allows phone PWB-level service and troubleshooting.
RH-53/54 Nokia Customer Care Product 6 5-Service Tools Service Tool Photo Description Info SF-33 POS Flash Adapter The flash adapter allows FBUS/ MBUS connections for flashing. Pack of test 10 test pins to be used with SF-33 and DA-27. ST-12 Rework stencil Front End Module (FEM) RJ-51 Rework Jig To be used with ST-12.! COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 5-Service Tools Nokia Customer Care ■ Standard service tools Product Service Tool Photo Description Info ACF-8 Universal Power Supply ACF-8 is used to power FPS-8 and FLS-4S. ACF-8 has 6 Vdc and 2.1A output. FLS-4S POS Flash Adapter The Point of Sale (POS) flash is a low-cost software upgrade tool. This requires the XCS-1 cable and ACP-8U for operation. FPS-8 Flash Prommer The Flash Prommer FPS-8 is used for heavy flash.
RH-53/54 Nokia Customer Care Product PKD-1 5-Service Tools Service Tool SW Security Device Photo Description Info SW security device PKD-1 is hardware device that, when connected to the parallel (LPT) port of the PC, enables the use of the service software. Without the dongle present, it is not possible to use the service software. Printers or other peripheral devices can be connected to the PC through the dongle, if needed.
RH-53/54 5-Service Tools Product Nokia Customer Care Service Tool Standard toolkit Issue 2 06/2005 Photo Description Info Content: -Nokia opening tool SRT-6 -Tonichi torque driver -Hoya micro fibre cloth MX304 -Dastex gloves S, M, XL -Artilux goggles AH166 -Wera bit T5 867/4TX 5x50 -Wera bit T6 867/4TX 6x50 -Wera bit T6 867/4 6IPx50 -Facom side cutter 416E -Facom T5 driver SP.14032 -Facom T6 driver SP.14033 -Facom slot screwdriver AEF. 2x35.
RH-53/54 Nokia Customer Care 5-Service Tools ■ Service Cables Product Service Tool Photo Description Info AXS-4 Service Cable The AXS-4 D9-D9 service cable is used to connect two 9-pin connectors (e.g., between PC and FPS-8). AXS-4 length is 2 meters. DAU-9S MBUS Cable The MBUS cable DAU-9S has a modular connector and is used between PC serial port and, for example, the MJ-36. FLC-2 DC Cable FLC-2 is used to supply a controlled operating voltage.
RH-53/54 5-Service Tools Product Nokia Customer Care Service Tool Photo Description Info XCS-1 Service Cable The XCS-1 Service Cable is used to connect FLS-4S to SF-33. XCS-4 Modular Cable XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing and service purposes. XRF-1 RF Test Cable RF cable XRF-1 is used to connect e.g. Module Jig MJ-36 to RF measurement equipment.) Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 5-Service Tools ■ Docking Station Adapter Working Instruction Working instructions for docking station adapter DA-27. Insert the DA-27 like a battery, start at the battery connector side. First press the phone as shown in figure 1, then push down the phone and release the unit. First move the phone as shown in figure 1, then lift the phone carefully. Now remove the phone from DA-27. 12 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care RH-53/54 6-Disassembly and Assembly Instructions Issue 2 06/2005 Copyright 2005 Nokia Corporation.
RH-53/54 Nokia Customer Care 6-Disassembly and Assembly Instructions [This page left intentionally blank] 2 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 6-Disassembly and Assembly Instructions Nokia Customer Care Table of Contents Page No RH-53/54 Disassembly........................................................................................ 5 Domesheet Exchange instructions ................................................................. 12 RH-53/54 Reassembly....................................................................................... 14 Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 6-Disassembly and Assembly Instructions [This page left intentionally blank] 4 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 6-Disassembly and Assembly Instructions Nokia Customer Care RH-53/54 Disassembly Disassembly instructions It is very important to follow this insertion and removal procedure, otherwise the contact pins of Flash Adapter will be damaged. 1.) Insert the Flash Adapter SF-33 by starting at the Battery Connector side. 2.) First, press the locking of the Flash Adapter and then push it into the bottom side of the phone, do not use too much force. 3.
RH-53/54 Nokia Customer Care 6-Disassembly and Assembly Instructions 1.) Push down the Release Button before pulling the Battery Cover. 2.) Open the unit and protect the Window with a plastic film. 3.) The Backplate is attached to the Hinge Spring with two adhesive tapes. To avoid the snaps from breaking it is important that the Backplate is at first lifted on the right side referring to the "NOKIA" logo. 4.) Now, remove the Backplate adhesive.
RH-53/54 6-Disassembly and Assembly Instructions 7.) Fold the A-Face Assy as shown in the picture. 9.) Protect the inner side of the Window with a plastic film. 11.) Unscrew the four Torx Plus® size 6 screws of Lower Nokia Customer Care 8.) Remove the A-Face Assy from the B-Cover Upper Block carefully. 10.) Unscrew the four Torx Plus® size 6 screws of Upper Block. For assembly, the reverse order and a Torx Plus® driver with a torque of 27Ncm has to be used. 12.) Now, the B-Cover Lower Block… Block.
RH-53/54 Nokia Customer Care 6-Disassembly and Assembly Instructions Consider if the malfunction caused by Upper or Lower Block. Only open the Coax Connector and remove the Coax Cable on the defective Block of the unit. (For e.g. LCD / Vibra / IHF Speaker fault -> start disassemble upper part, Microphone / Keymat / Charger fault -> start disassemble lower part) 13.) …and the B-Cover Upper Block can be removed. 14.) Placement of the Coax Cable in the Lower Block. 15.
RH-53/54 6-Disassembly and Assembly Instructions Nokia Customer Care 21.) Unscrew the two Torx Plus® size 5 screws from 20.) Remove the Cable carefully. When assembling always starts with the Antenna Connector, "stretch" the cable towards hinge area carefully, then the same procedure when assembling at Engine Module side. Lower Block. For assembly, a Torx Plus® driver with a torque of 6Ncm has to be used. 22.) Put the Lower Block on the Upper Block as shown in the Picture. 23.
RH-53/54 Nokia Customer Care 6-Disassembly and Assembly Instructions 28.) Unlock the snaps before removing the IHF Antenna Chamber. 29.) Remove the Antenna Chamber. 30.) Release the four hooks carefully by using the SRT6. 31.) Separate the C2-Cover from LCD CAN Assy. 32.) Use tweezers when removing the Vibra Motor. 33.) Open the LCD Connector by using the SRT-6 carefully. 34.) Place the SRT-6 between LCD and the LCD Can as shown in the picture and lever out the LCD carefully. 35.
RH-53/54 6-Disassembly and Assembly Instructions 36.) Now, the Key Dome Shield can be removed. Nokia Customer Care 37.) The Engine Module can be removed easily. 38.) System Connector and Microphone drop out when turning the Shielding Can. Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 6-Disassembly and Assembly Instructions Domesheet Exchange instructions 1.) Take care not to damage the LED’s when exchanging the Domesheet. Start with SRT-6 as shown in the picture. 2.) Tweezers can be used to remove the defective Domesheet. 3.) Take the new Domesheet with tweezers. 4.) Place the Domesheet in the Key Dome Shield. 5.) Place the Dome Sheet straps into the slot of the Key Dome Shield. 6.) Same procedure on the opposite side.
RH-53/54 6-Disassembly and Assembly Instructions Nokia Customer Care 7.) Make sure that the edges and the screw holes of Domesheet and the Key Dome Shield are congruent to each other. 8.) Place the Key Dome Shield with the Domesheet on the Engine Module exactly and press-on the Domesheet carefully. Check if the Domesheet is correctly stuck to the Engine Module. 7.) Remove the Key Dome Shield again. 8.) Press on the Domesheet carefully. Ensure also, that there are no open edges or air gap.
RH-53/54 Nokia Customer Care 6-Disassembly and Assembly Instructions RH-53/54 Reassembly The reassembly takes place in reversed order. 14 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care RH-53/54 7-Troubleshooting Instructions Issue 2 06/2005 Copyright 2005 Nokia Corporation. All Rights Reserved.
RH-53/54 Nokia Customer Care 7-Troubleshooting Instructions [This page left intentionally blank] 2 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Baseband Troubleshooting................................................................................ 5 Baseband test points ......................................................................................... 5 Troubleshooting diagrams ................................................................................. 6 Phone is dead .................................................................................................... 7 Flash programming does not work.....
RH-53/54 Nokia Customer Care General instructions for TX troubleshooting ................................................... 52 Troubleshooting chart for GSM900 transmitter .............................................. 54 Logic signals for the Front End Module ......................................................... 55 Renesa FEM logic .......................................................................................... 55 RFMD FEM logic ..............................................................
RH-53/54 Nokia Customer Care Baseband Troubleshooting ■ Baseband test points Figure 1:BB test points Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Figure 2:BB test points 2 ■ Troubleshooting diagrams INOTE : Since both D200 (UEM) and D400(UPP) are underfilled, they can not be replaced. If either D200 or D400 is defective, the whole PWB has to be discarded. 6 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care ■ Phone is dead This means that the phone does not draw any current at all when supply is connected and/or power key is pressed. It is assumed that the voltage supplied is 3.6 VDC. The UEM will prevent any functionality what so ever at battery/supply levels below 2.9 VDC. Figure 3:Phone is dead troubleshooting Phone is dead Yes C227 VR3 = 2,78VDC No Check : C227, PW B. Yes Check : D450 (Flash).
RH-53/54 Nokia Customer Care ■ Flash programming does not work The flash programming can only be done via the pads on the PWB (J396). In case of Flash failure in FLALI station, problem is most likely related to SMD problems. Possible failures could be short-circuit of balls under µBGAs (UEM, UPP, FLASH). Missing or misaligned components. In flash programming error cases the flash prommer can give some information about a fault.
RH-53/54 Nokia Customer Care ■ Power does not stay on or phone is jammed If this kind of failure is presenting itself immediately after FLALI, it is most likely caused by ASICs missing contact with PWB. If for some reason the MCU does not service the watchdog register within the UEM, the operations watchdog will run out after approximately 32 seconds. Unfortunately, the service routine can not be measured.
RH-53/54 Nokia Customer Care ■ Display information : "Contact Service" This error can only happen at power up where several self-tests is run. If any of these test cases fails the display will show the message: "Contact Service". It's individual test cases so the below lineup of error hunting's has no chronological order. Use common sense and experience to decide which test case to start error hunting at.
RH-53/54 Nokia Customer Care ■ The phone does not register to the network, or the phone cannot make a call If the phone doesn't register to the network, the fault can be in either BB or RF. Only few signals can be tested since several signals is 'burried' in one or more of the inner layers of the PWB. First of all check that SIM LOCK is not causing the error by using a Test-SIM card and connect the phone to a tester.
RH-53/54 Nokia Customer Care ■ Charging troubleshooting Figure 8:Phone is OFF:no current from charger Phone is OFF - battery is completely empty (<=3,1VDC) and no current from charger when connected L100 VCHAR > 2,1VDC Check : No F100, L100, V100, C100, R200, System-connector. No F100, L100, V100, C100, R200, System-connector.
RH-53/54 Nokia Customer Care Figure 9:Display info:charger connected, not charging Display info when charger is connected : "Not charging" R206 Voltage on R206 towards D200 is ~0,8VDC when power is connected. No Check : X105, R202, R206, C240. Yes R207 Voltage (use scope) on R207 towards D200 is ~0,9VDC at peak. No Check : X105, R202, R207, C220. Yes R200 Voltage on R200 towards D200 same as VBAT voltage Check : No R200, PWB.
RH-53/54 Nokia Customer Care ■ Audio troubleshooting 1, 2 Figure 10:Microphone does not work Microphone do not work and the isn't any mechanical problem Z100 Check Z100 is working correctly (no short/open-circuit) No Replace : Z100 Replace : Mic and micboot Error still present R165 Check voltage level on R165 towards UEM (bias) = 2,1V Check : No R165, C168, PWB. Else defctive D200* No R153, R157,C151, C152, C153, C154,R171, PWB.
RH-53/54 Nokia Customer Care ■ Audio troubleshooting 3: Headset does not work Figure 12:Headset does not work Headset microphone do not work and the isn't any mechanical problem Z101 Check Z101 is working correctly (No short/open circuit) No Replace : Z101 Yes R151 Check voltage level on R151 towards UEM (bias) = 1,0V - 1,4V No Check : R166, R151, C171 Yes R151 Check voltage level on R151 towards UEM (bias) = 1,0V 1,4V Check XMIC line to UEM (D200) Check : No R156, C170, C174, C172, R169 Error
RH-53/54 Nokia Customer Care Upper block failures All checks can be done while the phone is partially disassembled (no need for full reasembly inbetween debugging steps): SIM failure (including insert SIM faults) 1. Flex B2B connector pressed in? 2. Change LCD can assembly (for new flex) works? 3. C314 (VSIM cap) short circuitting? 4. C313 (SIMIO cap) short circuitting? 5. Voltages (SIM startup sequence)? Board to Board connector pin17 6.
RH-53/54 Nokia Customer Care The error ”SIM card rejected” means that the ATR message received from SIM card is corrupted, e.g. data signal levels are wrong. The first data is always ATR and it is sent from card to phone. For reference a picture with normal SIM power-up is shown below. Normal SIM power-up sequence Ch1 : VSIM Ch2 : RESET Ch3 : CLOCK Ch4 : DATA Vibra failure 1. Flex B2B connector pressed in? 2. Change C2 cover assembly(new vibra)/Vibra works? 3.
RH-53/54 Nokia Customer Care Figure 13:Vibra troubleshooting Start Is there any vibration? No Yes Is there sufficient vibration? No Wrong setting or software error. Contact problem. Mechanical problem - counterweight is blocked Defective or missing vibra. Defective UEM. Software error Contact problem. Defective vibra. Defective UEM. Yes Vibra is constantly switched on? Yes Software error. Defective UEM. Short circuit. No Intermittent vibration? Yes Bad connection. Defective vibra.
RH-53/54 Nokia Customer Care 2. C2 cover mounted correct (red snap not vissible)? 3. Check if system connector is misplaced slightly? 4. Check for ”headset inserted symbol” in display? 5. Change speaker chamber/antenna works? 6. Change LCD can assembly (for new flex) works? 7. Change main PWB (UEM)? Display failure 1. Flex B2B connector pressed in? 2. Display B2B connector pressed in (press through hole in C2 cover assembly)? 3. Change display works? 4. Change LCD can assembly (for new flex) works? 5.
RH-53/54 Nokia Customer Care [This page intentionally left blank] 20 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Introduction to RH-53/54 RF Troubleshooting Three types of measurements are used in the following. It will be specified if the measurement type is "RF" “RF test” or "LF". • RF measurements should be done with a GSM tester and a suitable connector to the general RF input/output. That connection is for tuning and testing the whole RF in the phone. • RF test measurements should be done with a Spectrum Analyzer and a high-frequency 500ohm passive probe, for example HP54006A.
RH-53/54 Nokia Customer Care General description of the RF circuits In the following general desriptions different colours are used in the block diagram. The Lowband signal route is shown in red, the Highband route in green and the common signal lines are shown in blue. ■ Receiver signal path The signal from the antenna pad is routed to the Front End Module (FEM - N700).
RH-53/54 Nokia Customer Care order to control the TX level a sample of the signal is taken in the FEM and used in the power loop amplfier in Mjoelner to establish the right output power. The selection of which amplifier chain in the FEM to be active is controlled through the 4 controllines VC1, VC2, BS and Vtx.
RH-53/54 Nokia Customer Care is supplied to the reference divider (RDIV) where the frequency is divided by 65. The output of RDIV (400kHz) is used as reference clock for the Phase Detector (ϕ). The PLL synthesizer is a feedback control system controlling the phase and frequency of the LO-signal. Building blocks for the PLL are: Phase detector, Charge Pump, Voltage Controlled Oscillator (VCO), N-Divider and loopfilter. As mentioned earlier only the VCO and loopfilter is external to the Mjoelner IC.
RH-53/54 Nokia Customer Care Figure 16:Frequency plan To PCN RX mixer ASIC 2 2 To GSM RX mixer 2 2 VDDLO VDDPLL 1/2 VDDPRE 1/4 VDDCP 64/ 65 ϕ NDIV ADIV Charge Pump 1/4 1/2 CPOUT Lock Detect LOCNT REFCNT RDIV VDDXO Synth supply filter PLL loop filter VCXO supply filter Buffer 2 2 To PCN Modulator 2 VCXO Bias R2H/R2 2 To GSM Modulator VXO VR3 REFOUT REFOUT 1/2 VR5 Vcp supply filter VDDBBB Buf/ AGC VPLL XTALM XTALP INPLO 26MH z VVCO VR7 Mjoelner N600 VDDRXBB Main Bia
RH-53/54 Nokia Customer Care ■ RF Key component placement Figure 17:RF key component placement Table 2: Key component placement tABLE N600 Mjoelner RF IC Z601 PCN RX SAW High band RX SAW filter Z602 EGSM RX SAW Low band RX SAW filter Z603 EGSM TX SAW Low band TX SAW filter B600 26 MHz crystal G600 VCO ( 3.6 GHZ VCO ) N700 Front End Module (FEM) X700 RF connector 26 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Troubleshooting ■ Common circuit The power supply and the synthesiser is common for RH53/54, except for the synthesiser ranges. Power Supply Configuration All power supplies for the RF Unit are generated in the UEM IC (D200). All power outputs from this IC have a decoupling capacitor at which the supply voltage can be checked. The power supply configuration used in the phone is shown in the block diagram below: Figure 18:Power supply configuration Internal Mjoelner VR2 2.
RH-53/54 Nokia Customer Care The names to the left are the signal names used on the RF schematics Table 3: Supply names Supply name RF Supply name UEM Min Typ Max Unit VCP VR1A 4.54 4.75 4.9 V VTX VR2 2.64 2.78 2.86 V VXO VR3 2.64 2.78 2.86 V VPLL VR5 2.64 2.78 2.86 V VRX VR6 2.64 2.78 2.86 V VVCO VR7 2.64 2.78 2.86 V VBB VIO 1.72 1.8 1.88 V VREF2 VrefRF01 1.334 1.35 1.366 V VBATT BATTERY 3.1 3.6 5.
RH-53/54 Nokia Customer Care ■ General instructions for Synthesizer troubleshooting Start the Phoenix-Service-Software and Select:ProductRH53/54 or scan Select:Testing RF Controls Band XX, se table below Active UnitRX Operation ModeContinuous RX/TX ChannelYY se table below The signal from the VCO is measured at R640 using a spectrum analysator and a 500ohm passive probe. The frequency should be as found in the table below and the power should be around –20dBm.
RH-53/54 Nokia Customer Care Example Signal Measured at VCXO output (R420) Figure 20:Measured signal at VCXO output VCO The VCO is generating frequencies in the range of 3420.4MHz – 3839.2 MHz for the RH-53 and in the range 3296.8 to 3979.6 MHz for RH-54 when the PLL is running. The output frequency from the VCO is led to the Local oscillator input of the Mjoelner IC (N600), where the frequency is divided either by 2 or 4 in order to generate all channels in EGSM and PCN respectively.
RH-53/54 Nokia Customer Care ■ Troubleshooting chart for the Synthesizer Figure 21:Troubleshooting chart for synthesizer From Phoenix chose: File > product > RH-53/54 Maintenance > Testing > RF controls > band > RX > continous > channel Spectrum analyser VCO frequency (R640) MHz (see table) Yes Band and channel according to the previous table PLL block functional No Osciloskope VXO Power supply (C618) 2.78Vdc No Check UEM, SW Phone not in function Yes Osciloskope VXO Power supply (C620) 2.
RH-53/54 Nokia Customer Care If the phone stops working a short time after the power is turned ON, a possible reason for this might be the 26MHz system clock signal is not getting to the UPP clock-input in BaseBand. In this case check the following: Turn on the phone and check VCXO Power supply (C620) = 2.7V VCXO output (R420 – end not connected to C420) is 26MHz and approx. 700mVpp If this is not the case check the reference crystal (B600) and Mjolner (N600) as well as R420, R426, C420, C426.
RH-53/54 Nokia Customer Care Figure 23:Measurement points for the VCO Vctl VVCO (C624) VCO out (R640) Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care [This page left intentionally blank] 34 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Receiver Troubleshooting ■ Front End Module (FEM) control signals Depending on the vendor of the Front End Module (FEM), different timing of the control signals are present. The SW suppoerts both FEMs. R629 tells the SW which FEM control should be active. Renesas FEM control is used when R629 is 18K and RFMD FEM control is used when R629 is 82K. If the FEM is exchanged with an other type, the R629 must be changed, too.
RH-53/54 Nokia Customer Care ■ Measurements points Measurement points for the receiver Figure 24:Measurement points for the FEM BS (C709) VTX (J700) RX1800 VC1 (C708) VC2 (C730) RX900 Figure 25:RX interface points between N600/SAW filters L610/612 END Z601out L602/603 END 36 COMPA2005NY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Figure 26:Serial Bus interface measurement points RESETX RFBUSDA Mjoelner seriel interface RFBUSSENX RFBUSCLK Figure 27:I/Q measurement points RXQP RXIP Issue 2 06/2005 RXQM RXIM COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care ■ RH-54 Receiver General Instructions for GSM850 RX Troubleshooting Connect the phone to a PC with the module repair jig. Start Phoenix and establish connection to the phone Select->File ->Scan for product->CTRL-R Select-> Testing -> RFcontrols Select: Table 7: Band values Band: GSM850 Active Unit: RX Operation Mode: Continuous Rx/Tx Channel: 190 AGC: 9 The setup should now look like this: Figure 28:RF controls 38 COMPA2005NY CONFIDENTIAL Copyright © 2005 Nokia.
RH-53/54 Nokia Customer Care Figure 29:Troubleshooting chart for GSM850 receiver Apply -55dBm 881.6MHz (ch 190) Offset 67.71kHz from generator to X700 Osciloscope at RX I/Q. Signal 580mVpp DC offset 1.35V Freq. 67.
RH-53/54 Nokia Customer Care By measuring with an oscilloscope at RXIP or RXQP on a working GSM 850 receiver this picture should be seen Signal amplitude peak-peak 588 mV DC offset 1.33 V Figure 30:Measuring with oscilloscope 40 COMPA2005NY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care ■ General Instructions for GSM1900 RX Troubleshooting Connect the phone to a PC with the module repair jig. Start Phoenix and establish connection to the phone Select->File ->Scan for product->CTRL-R Select-> Testing -> RFcontrols Select: Table 8: Band values Band: GSM1900 Active Unit: RX Operation Mode: Continuous Rx/Tx Channel: 661 AGC: 9 The setup should now look like this: Figure 31:Control values Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia.
RH-53/54 Nokia Customer Care Figure 32:Troubleshooting chart for GSM1900 receiver Apply -55dBm 881.6MHz (ch 190) Offset 67.71kHz from generator to X700 Osciloscope at RX I/Q. Signal 580mVpp DC offset 1.35V Freq. 67.
RH-53/54 Nokia Customer Care By measuring with an oscilloscope at RXIP or RXQP on a working GSM1900 receiver this picture should be seen Signal amplitude peak-peak 588 mV DC offset 1.33 Figure 33:Measuring with the oscilloscope Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care ■ RH-53 Receiver General Instructions for GSM900 RX Troubleshooting Connect the phone to a PC with the module repair jig.
RH-53/54 Nokia Customer Care Figure 35:Troubleshooting chart for GSM900 receiver Apply -55dBm 942.4 MHz Offset 67.71kHz from generator to antenna pad Osciloskope at RX I/Q. Signal 588mVpp DC offset 1.35V Freq. 67.
RH-53/54 Nokia Customer Care By measuring with an oscilloscope at RXIP or RXQP on a working GSM900 receiver this picture should be seen Signal amplitude peak-peak 588 mV DC offset 1.33 V Figure 36:Measuring with oscilloscope General Instructions for GSM1800 RX Troubleshooting Connect the phone to a PC with the module repair jig. Start Phoenix and establish connection to the phone Select->File ->Scan for product->CTRL-R Select-> Testing -> RFcontrols 46 COMPA2005NY CONFIDENTIAL Copyright © 2005 Nokia.
RH-53/54 Nokia Customer Care Select: Table 10: Band values Band: GSM1800 Active Unit: RX Operation Mode: Continuous Rx/Tx Channel: 700 AGC: 9 The setup should now look like this: Figure 37:Rf controls Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Figure 38:Troubleshooting chart for GSM1800 receiver Apply -55dBm 1842.8MHz (ch 700) Offset 67.71kHz from generator to X700 Osciloscope at RX I/Q. Signal 580mVpp DC offset 1.35V Freq. 67.
RH-53/54 Nokia Customer Care By measuring with an oscilloscope at RXIP or RXQP on a working GSM1800 receiver this picture should be seen Signal amplitude peak-peak 588 mV DC offset 1.33 Figure 39:Measuring with oscilloscope Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care [This page left intentionally blank] 50 COMPA2005NY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care RH-53/54 Transmitter Troubleshooting The troubleshooting of the transmitter for the different phones is similar, meaning that the low band, 850/900 MHz, has similar values and the high band, 1800/1900 MHz, has similar values. The only differences are which selection of product done in Phoenix.
RH-53/54 Nokia Customer Care Figure 42:TXP and TXC test points General instructions for TX troubleshooting Apply an RF-cable to the RF-connector to allow the transmitted signal act as normal. RF-cable should be connected to measurement equipment or to at least a 10-dB attenuator, otherwise the PA may be damaged. Start Phoenix Service Software and: Establish a connection to the phone e.g. FBUS.
RH-53/54 Nokia Customer Care Select: Table 11: Band values Band: XX Active Unit: TX Operation Mode: Burst Rx/Tx Channel: YY TX Power level ZZ TX Data Type Random Select ”XX” , ”YY” and ”ZZ” according to the table below Table 12: Values Phone XX YY ZZ RH-54 GSM850 189 5 RH-53 GSM900 37 5 RH-53 GSM1800 700 0 RH-54 GSM1900 661 0 Your screen should look like this: Figure 43:Control values Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Measure the output power of the phone; it should be around 32.5 dBm for low band and 29.5 dBm for highband. Remember the loss in the jig; around 0 dB for the low band and 0.1 dB for the high band. Troubleshooting chart for GSM900 transmitter For the spectrum analyzer measurements in the following chart use the 500ohm passive probe giving an approximately 20 dB lower reading than indicate in the following figures.
RH-53/54 Nokia Customer Care Figure 45:Signals 32.5 dBm (29.5 dBm) + 2 dBm Attenuator R714 (R711) FEM N700 + 4 dBm Z603 (T600) TXC (R620) Max PW 1.6V Min PW 0.6 V VC1 VC2 VTX BS TXP (C646) 2.7V Vpc R712 Max PW: 1.2 Vdc Min PW: 0.65 Vdc Opamp (C644) Max PW 1.2 V Min PW 0.65 Mjoelner N600 Det Max PW: 1.13 vdc Min PW: 0.
RH-53/54 Nokia Customer Care RFMD FEM logic Table 14: RFMD FEM logic Vtx BS VC1 VC2 Mode VTX_B_P VTX_B_P Vant1 Vant2 Idle 0 0 0 0 Low Band RX 0 0 1 0 Low Band TX 1 0 1 0 High Band RX 0 1 1 0 High Band TX 1 1 1 0 Analog Power control signals (TXC, VPC, VDET) The pictures in the following page show the typical shapes of the control signals low band, right side it for highest power – left side for lowest power.
RH-53/54 Nokia Customer Care Figure 46:Power control signals High Power Low Power TXC TXC VPC VPC VDET VDET Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care I/Q signals The following diagrams show different situations of TX IQ measurements. Depending on the time the modulation may cause the signal to look different. 58 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Alignment ■ Manual alignment with Phoenix The alignment/calibration is the same in both GSM900/850 and GSM1800/1900 except for the channels and frequencies. Only the the procedures for GSM900/GSM1800 are shown. In Phoenix select connection Fbus scan product. If you power up the board before selecting Fbus, it works without any error messages. Use Jig or other device for RF and bus connection. Attenuation in the probe alone is 0dB for 900 and 0.1dB for 1800.
RH-53/54 Nokia Customer Care Follow the description in Phoenix, setting up the signal generator as described Figure 48:Calibration tuning Press the OK button Figure 49:Calibration tuning Press the Save&Continue botton. 60 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Follow the description in Phoenix, setting up the signal generator as described Figure 50:Calibration tuning Press the OK button Figure 51:Calibration tuning Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Press the Save&Continue botton Note! You have to follow the shown procedure. It is not possible to tune the high band alone. You need to make a tuning of the low band first to come to the high band. You can stop at any time by switching off the menu. If the values are outside internal specs, you can not save them and have to leave the tuning without saving. ■ RX Band Filter Response Normally not needed in repair.
RH-53/54 Nokia Customer Care Set the spectrum analyser or GSM tester for the required settings and press “OK” If a GSM tester is used, set the TX data type to random so that the tester can trig on the signal. Figure 54:TX tuning Tune the highlighted values to the wanted power (Use average burst power) Tune the base level to –25dBm When done press Save&Continue and Phoenix will automatically shift from lowband to highband.
RH-53/54 Nokia Customer Care Set the spectrum analyser or GSM tester for the required settings and press “OK” . If a GSM tester is used, set the TX data type to random so that the tester can trig on the signal. Figure 56:TX tuning Tune the highlighted values to the wanted power (Use average burst power). Tune the base level to –25dBm. When done press Save&Continue. The intermediate results are then calculated. The procedure has to be followed. First low band tuning and then high band tuning.
RH-53/54 Nokia Customer Care Figure 57:i/Q tuning Press Start Figure 58:I/Q tuning Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Set the spectrum analyser or GSM tester for the required settings and press “OK” Figure 59:I/Q tuning Begin tuning with data from selected place. Tune DC offset values to lowest carrier. Use Side arrows or +, - . Tune Amplitude and phase to lowest sideband. When satisfied with the result, press Next. (The sidebands should hardly be visible).Or for CMU200 the supression should be better than -40dBc. Figure 60:I/Q tuning 66 COMPANY CONFIDENTIAL Copyright © 2005 Nokia.
RH-53/54 Nokia Customer Care Set the spectrum analyser or GSM tester for the required settings and press “OK” Figure 61:I/Q tuning Press Start to begin tuning with data from selected place. Tune DC offset values to lowest carrier. Use Side arrows or +, - . Tune Amplitude and phase to lowest sideband. When satisfied with the result, press Finish. (The sidebands should hardly be visible). ■ RF control The purpoase is to check the receiver or transmitter without going in call.
RH-53/54 Nokia Customer Care Autotune (RH-53 with CMU200) ■ File adjustments Edit the file RH_53_tunings.ini and save it in the product folder under Phoenix with the right name. It defines the target values for the tunings which need targets or can be a general one that only needs small updates for the values that might change (e.g. the base target). Edit the file autotune_RH-53.ini and save it in the product folder under Phoenix with the right name.
RH-53/54 Nokia Customer Care With a PKD-1NS dongle the loss in cables and jigs has to be set, and the jig type must be defined to the product. When that is done the PKD-1 donkle can be used, and the losses can not be changed with that dongle. Figure 64:Set loss Select or add a jig and define the losses Figure 65:Set loss 2 Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care Make sure the product has the right type of jig. (At the moment new products like RH-54 can not be added) Figure 66:Set loss 3 Note! CMU200: Remember that CMU200 is left as it was set in the autotune. Attenuation settings are at 0. 70 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
Nokia Customer Care RH-53/54 8-System Module Issue 2 06/2005 Copyright 2005 Nokia Corporation. All Rights Reserved.
RH-53/54 Nokia Customer Care 8-System Module [This page left intentionally blank] 2 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 8-System Module Nokia Customer Care Table of Contents Page No Abbreviations ...................................................................................................... 6 Introduction ......................................................................................................... 9 Technical Summary ........................................................................................... 9 List of Features .....................................................................
RH-53/54 Nokia Customer Care 8-System Module Memory Module ............................................................................................... 28 Fold detection-switch ....................................................................................... 28 SIM Interface.................................................................................................... 29 SIM -reader ....................................................................................................
RH-53/54 8-System Module Nokia Customer Care [This page left intentionally blank] Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 8-System Module Abbreviations 6 Abbr. Description ADC Analog Digital Connector ASIC Application Specific Integrated Circuit ATR Answer To Reset BB Baseband BL-4C Battery type. BSI Battery Size Indicator Cbus Control bus (internal phone interface between UPP-UEM) CTSI Clock Timing Sleep and Interrupt Dbus DSP controlled bus (Internal phone interface between UPP-UEM) DC Direct Current DCT4.0 Digital Core Technology, generation 4.
RH-53/54 8-System Module Nokia Customer Care Mbus Asynchronous message bus connected to MCU (phone control interface). Slow message bus for control data. MCU Micro Controller Unit NO_SUPPLY UEM state where UEM has no supply what so ever NTC Negative temperature Coefficient, temperature sensitive resistor used as a temperature sensor. PA Power Amplifier (RF) PDM Pulse Density Modulation Phoenix SW tool of DCT4.
RH-53/54 Nokia Customer Care VMSTR+, VMSTR 8 8-System Module Master Reset threshold level COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 8-System Module Nokia Customer Care Introduction This document specifies the baseband module for the RH-53/54 platform program. The baseband module includes the baseband engine chipset, the UI components and the acoustical parts for the transceiver. RH-53/54 is a hand-portable dualband GSM/GPRS 900/1800MHz fold-phone, having the DCT4 generation baseband (UEM/UPP) and RF (MJOELNER) circuitry. The RH-53 platform also supports a GSM 850/1900 US variant called RH-54.
RH-53/54 Nokia Customer Care 8-System Module The UEM supplies both the baseband module as well as the RF module with a series of voltage regulators. Both the RF and baseband modules are supplied with regulated voltages of 2.78 V and 1.8V. UEM includes 6 linear LDO (low drop-out) regulators for baseband and 7 regulators for RF. The UEM is furthermore supplying the baseband SIM interface with a programmable voltage of either 1.8 V or 3.0 V. The core of the UPP is supplied with a programmable voltage of 1.
RH-53/54 8-System Module Nokia Customer Care • Polyphonic ringing tones • 2 white LED’s for LCD Backlight. • 2 white LEDs for key mat & 3 blue LED’s for Light-effect in key mat. • JAVA • MMS • GPRS Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 8-System Module Technical Specifications ■ Modes of Operation RH-53/54 baseband engine has six different ‘normal’ operating modes: • Νo supply • Power off • Αcting dead • Active • Sleep • Charging No supply In this mode the phone has no supply voltage. The phone enters this mode if the battery is disconnected, or the battery voltage drops below VMSTR- (1.8V~2.
RH-53/54 8-System Module Nokia Customer Care Acting dead This mode is just a sub mode of normal ‘Active’ mode, where everything, except for VSIM and the RF parts, is powered up. This mode is only used for when the phone is in ‘Power off’ or ‘No supply’ mode and a charger is connected. To the user, the phone acts as if it was switched off. A battery-charging alert is given and/or a battery charging indication on the display is shown, to acknowledge the user that the battery is being charged.
RH-53/54 Nokia Customer Care 8-System Module its 3.6V / 5.0V / 5.25V). Charge current is monitored by measuring the voltage drop across a 0.22 ohm resistor. ■ Regulators Overview of the regulator state in ‘Active’, ‘Acting dead’ and ‘Sleep’ mode is shown in table 1.
RH-53/54 8-System Module Nokia Customer Care ■ DC Characteristics Supply Voltage Ranges Table 2: Supply voltage ranges Signal Rating Battery Voltage 0 ... 4.39V (VBAT) Flashing Voltage 0 … 5.15V Charger Input Voltage -0.3 ... 9.2VRMS (16,9 Vpeak) Following voltages are assumed as normal and extreme voltages for used battery: Table 3: Battery voltages Source Min Nom Max Note VBAT 3.21V 3.80V 4.39V 1 Vcoff+ 3.0V 3.1 3.2 HW off to on Vcoff- 2.7V 2.8V 2.9V HW on to off Vmstr+ 2.
RH-53/54 Nokia Customer Care 8-System Module Regulators Voltage Ranges Table 4: Regulators voltage ranges Source Min Nom Max Note VANA 2.70V 2.78V 2.86V Imax = 80mA VFLASH1 2.70V 2.78V 2.86V Imax = 70mA Isleep = 4mA VFLASH2 2.70V 2.78V 2.86V Not used VSIM 1.745V 2.91V 1.8V 3.0V 1.855V 3.09V Imax = 25mA Isleep = 0.5mA VIO 1.72V 1.8V 1.88V Imax = 150mA Isleep = 0.5mA VCORE Higher range 1.000V 1.140V 1.235V 1.425V 1.710V 1.053V 1.2V 1.3V 1.5V 1.8V 1.106V 1.260V 1.365V 1.
RH-53/54 8-System Module Nokia Customer Care ■ Interconnection Diagram Figure 2:IPower distribution diagram Baseband UEM VR1A RF Regulators VR2-7 6 SIM VSIM VCORE UPP VANA Baseband Regulators LED+ FLASH VIO RTC LED Driver VFLASH1 LCD Battery VBAT CHACON Boomer PA Supply System Connector ■ External Signals and Connections Battery connector The battery temperature is estimated by measurement in the transceiver PWB with a separate NTC resistor. Thus the Battery Interface has only 3 contacts.
RH-53/54 Nokia Customer Care 8-System Module Baseband - RF interface The interface between the baseband and the RF can be divided into three categories: - The digital interface from the UPP to the RF ASIC (Mjoelner). The serial digital interface is used to control the operation of the different blocks in the RF ASICs. - The analogue interface between UEM and the RF. The analogue interface consists of RX and TX converter signals.
RH-53/54 8-System Module Nokia Customer Care Speaker (Ringer & Earpiece) Table 9: Connections between UPP and Boomer Signal Shutdown (Only Ringer) From To Parameter UPP GENIO[14 ] Boomer Shutdown (pin 5) Vih Vil Min. 1.2 - Max. - 0.4 Unit VV Notes Boomer Shutdown treshold levels Table 10: Connections between UEM/Battery and Boomer Signal name Paramete r From To XAUDIO[1] Filtered signal Differential between HF and HFCM.
RH-53/54 Nokia Customer Care 8-System Module Pin Signal Comments 21 GND 22 EARP For MALT 23 EARN For MALT 24 GND 25 VDD "Vflash1" 2.78 V for Display 26 LED- Return from LEDs 27 LED+ Pos supply for LEDs 28 VDDI "Vio" 1.80 V for Display 29 LCD_RESETX Display Reset 30 LCD_SI Display Serial Data Figure 3:Flex con. pin out Pin 30 20 Pin 1 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 8-System Module Nokia Customer Care ■ Baseband board clocks Table 12: Board Clocks Signal name From To Min. Typ. Max. Unit Notes RFCLK MJOELNER UPP - 26 - MHz Active when SLEEPX is high SLEEPCLK UEM UPP - 32.
RH-53/54 Nokia Customer Care 8-System Module Functional Description Audio External RH-53/54 is designed to support fully differential external audio accessory connection. A headset and PnPHF can be directly connected to system connector. Detection of the different accessories is made in analog way by reading the DC voltage value of EAD converter. Figure 4:External audio interface 2.7V Not all components are shown Hookint /MBUS EAD Headint Bottom Connector Mic_bias 2.1V MICB2 MIC2P 33N MIC2N HF 3...
RH-53/54 8-System Module Nokia Customer Care Table 13: Comparator threshold levels and pull-up current source strength (hysteresis included) Parameter Variable Min Typ Max HOOKINT comparator threshold Vhook1 1.21 V 1.35 V 1.49 V HOOKINT comparator threshold Vhook2 0.50 V 0.60 V 0.70 V HEADINT comparator threshold Vhead 1.71 V 1.90 V 2.09 V VFLASH1 voltage regulator VFLASH1 2.70 V 2.78 V 2.
RH-53/54 Nokia Customer Care 8-System Module ■ Audio Internal Earpiece/Ringer The transducer used both as earpiece and ringer is the 16 mm loudspeaker called MALT. This solution will implement polyphonic ringing tones.
RH-53/54 8-System Module Nokia Customer Care Microphone The acoustical design is copied from Nokia 7210 with some modifications. The microphone boot is a separate component placed next to the bottom connector. The electrical Microphone design is a differential bias circuit, driven directly from the MICB1 bias output with external RC-filters. The RC filter (220 Ω, 4.7µF) is scaled to provide damping at 217 Hz. The microphone bias is controlled in the 8 bit AudioBiasR register.
RH-53/54 Nokia Customer Care 8-System Module ■ Batteries Type:BL-4C battery Technology:Li-Ion. 4.2V charging. 3.1V cut-off Capacity:760 mA/h Figure 7:BL-4C battery The BSI values for the batteries: Inside the battery, an over-voltage protection circuit are present. The battery does not contain a temperature sensor. Since the battery is using the Li-Ion technology, care should be taken while charging. The material might be overheated when charged above 60 degrees Celsius.
RH-53/54 8-System Module Nokia Customer Care GenIO20 Soft Right In Up GenIOInt2 Falling edge interrupt GenIO21 * In Up GenIOInt3 Falling edge interrupt GenIO25 Up In Up GenIOInt4 Falling edge interrupt GenIO27 1 In Up GenIOInt6 Falling edge interrupt GenIO28 Left In Up GenIOInt7 Falling edge interrupt GenIO13 # In Up GenIOInt1 Falling edge interrupt P00 Send In Up P0 int Falling edge interrupt P01 3 In Up P0 int Falling edge interrupt P02 9 In Up P0 int
RH-53/54 Nokia Customer Care 8-System Module ■ Display & Keyboard Backlight LCD Backlight LCD Backlight consists of 2 side firing white LED's, which are placed on the display FPC below the LCD area. Keyboard light effects Keyboard is lighting up by 2 white side firing LED’s for keyboard. 3 blue LED’s are used for Light effects in the keyboard. ■ LCD The LCD display module is a 130 x 3RGB x 130, 4096-color/ 256-color /8-color transflective passive matrix (CSTN) LCD display.
RH-53/54 8-System Module Nokia Customer Care ■ SIM Interface The SIM interface can be described as electrical interface between the SIM card and the phone via UEM. The SIM interface in the UEM contains power up/down, port gating, card detect, data receiving, ATR-counter, registers and level shifting buffers logic.
RH-53/54 Nokia Customer Care 8-System Module SIM switch and card detection The SIM power up/down sequence is generated in the UEM. This means that the UEM generates the RST signal to the SIM. A mechanical switch is connected to UEM SimCardDet pin to monitor the presence of the SIM card, i.e. card detection. When the SIM card is inserted, the switch connects the SimCardDet to GND.
RH-53/54 8-System Module Nokia Customer Care Assembly ■ Flex RH-53/54 uses a single layer flex with ground tracks distributed between signal groups, and wide ground tracks running in both sides of the flex to serve as main ground. Issue 2 06/2005 COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 Nokia Customer Care 8-System Module Test Interfaces Test pattern is placed on engine PWB, for service purposes, same test pattern is used for after sales purposes as well. Through MBUS or FBUS connections, the phone HW can be tested by PC software (Phoenix) and equipment.
RH-53/54 8-System Module Nokia Customer Care ■ Test points The following table show the test points on the main board.
RH-53/54 Nokia Customer Care 34 8-System Module J421 RFBUSCLK J422 RFBUSDA J423 RFBUSEN1 J424 GENIO 7 (BB-RF Interface) J600 RXIP (Mjoelner) J601 RXIM (Mjoelner) J602 RXQP (Mjoelner) J603 RXQM (Mjoelner) COMPANY CONFIDENTIAL Copyright © 2005 Nokia. All Rights Reserved.
RH-53/54 8-System Module Nokia Customer Care RF Functional Descriptions ■ RF block diagram Block diagrams of direct conversion receiver and transmitter RF section has described in the following figure. The architecture is based on Mjoelner, the RF ASIC, which contains most of the functionality of the RF Engine. The ASIC contains RX and TX functions, VCXO (crystal is placed external to the ASIC), se the block diagram.
RH-53/54 Nokia Customer Care 8-System Module The VCO for the 900/1800 (RH-53) bands covers the range of 3420 to 3840 MHz, while the VCO for 850/1900 (RH-54) (and thereby the quad band) covers 3296 to 3980 MHz. PLL Synthesizer, Functional Description The frequency synthesis PLL in conjunction with the VCO and 2/4 dividers generates the LO signal for both RX and TX paths, locked to the VCXO which again is locked to the base station through the AFC.
RH-53/54 8-System Module Nokia Customer Care ■ Transmitter The transmitter chain consists of two direct frequency I/Q-modulators, one for the GSM850/EGSM900 and one for GSM1800/1900, and a dual-band power amplifier. The I/Q-signals, generated in BB, are fed to the individual I/Q-modulators in the RF-ASIC. The frequency and phasing parameters for the individual modulators/bands is generated by the LO dividers, division is by 2 in GSM1800/1900 and by four in GSM900/E-GSM900.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 RH-53/54 Schematic Diagrams Issue 2 06/2005 Copyright © Nokia 2005 Corporation. All rights reserved.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) Table of Contents Issue 2 06/2005 RH-53/54 Page DCT4 common band schematics 3 System connector, Audio 4 UEMK 5 UPP, Combo memory 6 UI, B to B connector, Keyboard 7 RF part 8 Signal overview 9 Component finder, 1eja_09a (original) 10 Component finder, 1ejm_02a (updated) 11 Copyright © Nokia 2005 Corporation. All rights reserved.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 DCT4 common baseband KEY_UI Page 7 SIM IF( 3:0 ) IHF_XEAR(1:0) LCDUI(2:0) Page 6 KEYB(10:0) IHF_XEAR(1:0) LCDUI(2:0) KEYB(10:0) GENIO(31:0) UIDRV(5:0) UIDRV(5:0) RF_BB PWRONX PWRONX SLOWAD(6:0) Page 8SLOWAD_O(6:0) SLOWAD(6:0) SLOWAD_O(6:0) DIFDATA(7:0) RFCONV(9:0) RFCONV_O(9:0) MULTIGND DIFCTRL(3:0) AGND1 AGND1 AUDUEMCTRL(3:0) AGND2 AGND2 EAR(1:0) RFAUXCONV_O(2:0) LPRFCLK_I 1 RFCLK 2 RFCL
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 System connector, Audio System connector UEMK Microphone 2.1V when microphone active B to B connector UPP Customer Care EMEA / Service & Support Readiness / Training Group Issue 2 06/2005 Copyright © 2004 - 2005 NOKIA Only for training and service purposes Version: 4.0 Copyright © Nokia 2005 Corporation. All rights reserved. 2650 RH-53 10.06.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 UEMK UEMK L260 600R/100MHz L261 600R/100MHz L262 600R/100MHz L265 600R/100MHz ~4V VBAT D200 UEMK_V4.4_WDOGS_ENABLED C260 1u0 GND Charger plug C261 1u0 GND GND C262 1u0 GND C265 1u0 5 B200 32.768kHz GND 4 C209 10p AUDIO(6:0) System connector PWRONX C210 10p ~0.5V GND B to B connector C211 1u0 GND GND C213 1u0 C212 1u0 VANA GND GND 2.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 UPP, Combo memory 1.8V J402 UPP J403 J404 1 D400 UPP8M_V2.6_2.10 GND 0 1 2 3 UEMK, B to B connector, Keyboard GENIO(31:0) Combo memory 1.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 UI, B to B connector,Keyboard Keyboard B to B connector 1.8V C322 68p UPP 2.8V G ND EARN EARP R308 L305 0R 39nH R309 L306 0R 39nH R310 L307 0R 39nH 1.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 RF part Variant Band Cha nnel RX VCO/RX VC/RX TX VCO/TX VC/TX 2650/RH-53 GSM900 37 942.4MHz 3796.6MHz ~2.77V 897.4MHz 3589.6MHz ~2.43V 2650/RH-53 GSM1800 700 1842.8MHz 3685.6MHz ~2.03V 1747.8MHz 3495.6MHz ~1.64V 2651/RH-54 GSM850 189 881.4MHz 3525.6MHz ~1.76V 836.4MHz 3345.6MHz ~1.01V 2651/RH-54 GSM1900 661 1960.0MHz 3920.0MHz ~3.33V 1880.0MHz 3760.0MHz ~2.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 Signal overview 15 VR7=2.8V VR1A=4.75V 19 1) SLEEPCLK at J404 2) RFCLK at R420 3) 26MHz at B600 4) 32kHz at C209 VTX BS VR5=2.8V RESETX 9 18 21 VR3=2.8V 11 5) 32kHz at C210 6) CBUSCLK at J406 7) CBUSDA at J407 10 8) CBUSEN at J408 VC1 20 2 16 13 3 10) RFBUSCLK at J421 11) RFBUSEN at J423 14 4 VR2=2.8V 9) RFBUSDA at J422 VC2 VR1A=4.75V 5 VR6=2.8V 12) RX I/Q at J600-J603 17 VR7=2.
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 Component finder, RH-53 (1eja_09a) B B200 B600 C C100 C101 C102 C103 C105 C106 C123 C124 C151 C152 C153 C154 C157 C158 C159 C168 C170 C171 C234 G3 J5 C235 J4 D6 C236 G2 C237 I4 L5 C238 H4 M6 C239 I2 M6 C240 J2 M7 C243 J3 M2 C244 J2 M2 C260 G5 M4 C261 H5 M4 C262 G4 J4 C263 I5 J3 C264 G4 K3 C265 J2 K4 C310 B8 J2 C312 C8 K3 C313 A5 G5 C314 A5 K4 C315 A5 K3 C316 A5 K2 C317 D4 C642 C643 C644 C645 C646 C704 C707 C708
Nokia Customer Care Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) RH-53/54 Component finder, RH-54 (1ejm_02a) B B200 B600 C C100 C101 C102 C103 C105 C106 C123 C124 C151 C152 C153 C154 C157 C158 C159 C168 C170 C234 G3 J5 C235 J4 D6 C236 G2 C237 I4 L5 C238 H4 M6 C239 I2 M6 C240 J2 M7 C243 J3 M2 C244 J2 M2 C260 G5 M4 C261 H5 M4 C262 G4 J4 C263 I5 J3 C264 G4 K3 C265 J2 K4 C310 B8 J2 C312 C8 K3 C313 A5 G5 C314 A4 K4 C315 B5 K3 C317 D4 C642 C644 C645 C646 C704 C708 C709 C711 C727 C728 C729
Nokia Customer Care Issue 2 06/2005 Schematics / Layouts 1eja_09a (original) and 1ejm_02a (updated) Copyright © Nokia 2005 Corporation. All rights reserved.
