CCS Technical Documentation RH-17 Series Transceivers Service Tools Issue 1 04/2003 Confidential Nokia Corporation
RH-17 Service Tools Page 2 CCS Technical Documentation Nokia Corporation Confidential Issue 1 04/2003
RH-17 Service Tools CCS Technical Documentation Contents Page No Service Tools.................................................................................................................. 5 2280 .............................................................................................................................5 Flashing and Testing Setups ........................................................................................ 11 Service Case #1 ...............................................
RH-17 Service Tools Page 4 CCS Technical Documentation Nokia Corporation Confidential Issue 1 04/2003
RH-17 Service Tools CCS Technical Documentation Service Tools 2280 Photo Issue 1 04/2003 Code Service Tool Code Description Info MJS-82 Service Jig 0770474 MJS-82 secures and allows easy access to critical areas of the handset’s PWB during troubleshooting. It supports regulated and unregulated DC input voltages, Local and Normal mode operations, headset jack for audio tests, R-UIM card reader, second DC input for VCHAR used in EM tuning.
RH-17 Service Tools Photo Page 6 CCS Technical Documentation Code Service Tool Code Description Info RJ-13 Rework Jig 0770574 This tool serves as a mechanical PWB holder for desoldering and soldering of components. This tool is NOT intended to serve as a test jig. MJF-28 Docking Station Adapter 0770484 This device works in conjunction with JBV-1 Docking Station and the FPS-8 Prommer Box to allow calibration, tuning, and/or software flashing of the handset.
RH-17 Service Tools CCS Technical Documentation Photo Issue 1 04/2003 Code Service Tool Code Description Info SKT-3 Test A-Cover 0770541 The SKT-3 A-cover allows the technician to replace the handset’s original Acover with one that provides access to the CDMA and GPS RF connectors. The test A-cover is best suited for test cases where UI (keypad + LCD) functionality is required. SKT-3 only supports the XRS-4 RF test cable. XRS-4 RF Test Cable 0730221 Use with the SKT-3 Acover.
RH-17 Service Tools Photo Page 8 CCS Technical Documentation Code Service Tool Code Description Info JBV-1 Docking Station 0770298 The Docking Station and the Docking Station Adapter are needed for Mbus, Fbus, RF, and audio connections. This setup allows connection between flash prommers. When the audio box is connected, it has to be connected to the phone’s audio connector. The Docking Station can be powered by FPS-8 or external power supply.
RH-17 Service Tools CCS Technical Documentation Photo Code Service Tool Code Description Info FLS-4S POS Flash Adapter 0080543 The Point of Sale (POS) flash is a low-cost software upgrade tool. This requires the XCS-1 cable and ACP-8U for operation. DAU-9T FBUS Cable 0730267 The FBUS cable DAU-9T provides a connection from the serial port of the computer to the system connector of the phone.
RH-17 Service Tools CCS Technical Documentation Flashing and Testing Setups Service Case #1 This setup is best suited for Point of Sale (POS) locations using Diego Service Software. The picture below shows the FLA-44 device attached to the handset. Power is provided to the FLA-44 by the FLA-4S flashing device, which in turn is powered by an external power supply. The FLS-4S device connects to the parallel port of the PC running the Diego application.
RH-17 Service Tools CCS Technical Documentation Service Case #2 This setup illustrates an MJF-28 with a Haukka handset together with a Test A-cover and two XRS-4 RF test cables. This application could be used during testing and/or troubleshooting where the UI functionality of the handset is required for such tests. For repetitive tests, the SA-9 and RF cable solution configuration (Service Case #3) is a better solution since it eliminates the time it takes to place the Test A-cover.
RH-17 Service Tools CCS Technical Documentation Service Case #3 This configuration shows an MJF-28 with a Haukka handset and two SA-9 RF supports plus two CA-8RS RF test cables. This application could be used during RF calibration, and for CE and GPS testing. This is an easy and secure method of performing the same tests the Test A-cover solution provides, but it is best suited for repetitive testing.
RH-17 Service Tools CCS Technical Documentation Service Case #4 This setup illustrates the MJS-82 with XRS-4 RF test cables, connected to an FPS-8 prommer box. This setup allows troubleshooting and flashing of the engine at the same time. The jig also could be connected directly to the PC running Phoenix, using the general purpose DAU-9S cable.
RH-17 Service Tools Page 14 CCS Technical Documentation Nokia Corporation Confidential Issue 1 04/2003
