Nokia Customer Care 2115i/2116/2116i (RH-66) Mobile Terminals Service Tools Issue 1 03/2005 Company Confidential ©2005 Nokia Corporation
115i/2116/2116i (RH-66) Service Tools Contents Page 2115i/2116/2116i Service Tools................................................................................................................. 3 AAS-10A RF Probe ...................................................................................................................................... 3 CA-5S DC Service Cable ............................................................................................................................
Nokia Customer Care 2115i/2116/2116i (RH-66) Service Tools 2115i/2116/2116i Service Tools AAS-10A RF Probe The AAS-10A allows you to troubleshoot the handset. You can use the probe with the XRS-6 RF Cable. CA-5S DC Service Cable The CA-5S is used for energy management calibration with the JVB-1 Docking Station. CA-10PS Service Power Cable The CA-10PS is used to provide DC power to the SS-13 Tuning Station from a Keiphley power supply for CDMA tuning.
2115i/2116/2116i (RH-66) Service Tools CA-22DS Flash Cable The CA-22DS allows bottom connector flashing using the FLS-4S Flash Adapter or the FLC-20 Flash Device. CA-25RS RF Test Cable The CA-25RS test cable is used for RF engine testing and tuning. This cable snaps directly on the mobile terminal’s RF connector and converts the output to an surface mounting assembly connector. Removal of the A-cover is required.
Nokia Customer Care 2115i/2116/2116i (RH-66) Service Tools CPL-8 GPS Antenna Coupler The CPL-8 allows authorized service centers to test the GPS antenna during handset troubleshooting. The coupler is attached to (and detached from) the MJF-28 Docking Station Adapter. Note: The MJF-28 and the coupler assembly fit into the JXS-1 Shield Box DAU-9S FBUS/MBUS Cable The DAU-9S is a general purpose cable that supports FBUS/MBUS communication between a Mod-10 device and a PC.
2115i/2116/2116i (RH-66) Service Tools DKU-5F Flash Cable The DKU-5F is a single-cable flashing solution for CDMA handsets that include Pop-portTM connectors. This cable supports Diego, Phoenix, and UPST service tools. Note: Customers using the UPST application also require a Spirent protection key (dongle). Note: The DKU-5F is not supported in the APAC and LTA markets. FLA-30 Flash Adapter The FLA-30 allows power and flash connections through the battery compartment.
Nokia Customer Care 2115i/2116/2116i (RH-66) Service Tools FPS-8 Flash Prommer The FPS-8 is used for mobile terminal flashing at authorized service centers. Note: The FPS-8 is no longer available in some regions. For more information, see "FPS-10 Flash Prommer". FPS-10 Flash Prommer The FPS-10 replaces the FPS-8 Flash Prommer. The FPS-10 allows the flash code to be pre-loaded into the unit's memory and then can be flashed directly to the handset at high speeds.
2115i/2116/2116i (RH-66) Service Tools MJ-42 Module Test Jig The MJ-42 allows PWB-level service and troubleshooting for authorized service centers. It supports regulated and unregulated DC input voltages and includes Local and Normal Mode operations, a headset jack for audio tests, a RUIM card reader, and a second DC input for VCHAR used in EM tuning. The MJ-42 also supports simultaneous RF connections to the CDMA engine. A completely functional UI module is provided on the right side.
2115i/2116/2116i (RH-66) Service Tools Nokia Customer Care PKD-1 Software Security Dongle The PKD-1 is a hardware dongle that, when connected to the parallel (LPT) port of the PC, enables the use of the service software. It is not possible to use the service software without the dongle. Printers or other peripheral devices can be connected to the PC through the dongle, if needed. Caution: Make sure that you have switched off the PC and the printer before making connections.
2115i/2116/2116i (RH-66) Service Tools RJ-32 Rework Jig The RJ-32 serves as a holder for PWB component de-soldering and soldering. RJ-64 LNA LGA Rework Jig and ST-24 Stencil The ST-24 stencil allows rework on LGA-type components that do not have pre-tinned pads. The LNA requires the use of this stencil. The stencil is designed to specifically fit the pad configuration and dimensions while the rework jig fits the physical dimension of the LNA. Note: Used in conjunction with the SPS-1 Paste Spreader.
2115i/2116/2116i (RH-66) Service Tools Nokia Customer Care RJ-65 TX IC LGA Rework Jig and ST-25 Stencil The ST-25 stencil allows rework on LGA-type components that do not have pre-tinned pads. The Tx RF IC requires the use of this stencil. The stencil is designed to specifically fit the IC pad configuration and dimensions while the rework jig fits the physical dimension of the IC. Note: Used in conjunction with the SPS-1 Paste Spreader.
2115i/2116/2116i (RH-66) Service Tools SS-13 Tuning Docking Station The SS-13 is used with the MJF-x/DA-x Docking Station Adapters (shown with MJF-17) for CDMA RF autotuning. SS-38 Alignment Jig The SS-38 is used to align the adhesive domesheet assembly onto the PWB in the proper location during domesheet replacement. SX-4 Smart Card The SX-4 is used with the FPS-10 Flash Prommer for DCT4 flashing security.
Nokia Customer Care 2115i/2116/2116i (RH-66) Service Tools XCS-4 MBUS/FBUS Cable The XCS-4 is a general purpose cable for flashing and communicating with the mobile terminal. It is used to connect the FPS-8 Flash Prommer to the docking station adapter or the service jig.
2115i/2116/2116i (RH-66) Service Tools Flashing, Testing, and Tuning These setups are designed for use with Phoenix Service Software. Both manual testing and automated tuning are permitted.
2115i/2116/2116i (RH-66) Service Tools Nokia Customer Care Service Configuration 2: Flash Programming Using Docking Station FPS-8 Setup 1 3 2 5 4 Item Name Type 1 Flash Prommer sales pack: Service Cable USB Cable Power Supply FPS-8 CA-10DS AXS-4 ACF-8 2 Docking Station JBV-1 3 Docking Adapter MJF-17 4 DC Power Cable PCS-1 5 Modular Cable XCS-4 Software Security Dongle (not shown) PKD-1 Service software (not shown) CDMA Phoenix Issue 1 03/2005 ©2005 Nokia Corporation Company Con
2115i/2116/2116i (RH-66) Service Tools FPS-10 Setup 2 6 5 4 3 1 Page 16 Item Name Type 1 Flash Prommer sales pack: USB Cable Power Supply FPS-10 CA-31D AC-33 2 Docking Station Adapter MJF-17 3 Docking Station JBV-1 4 Service Power Cable CA-41PS 5 Smartcard SX-4 6 Modular Cable XCS-4 Service Power Cable (not pictured) CA-10PS SoftwareSecurity Dongle (not pictured) PKD-1 Service software (not pictured) CDMA Phoenix ©2005 Nokia Corporation Company Confidential Issue 1 03/200
2115i/2116/2116i (RH-66) Service Tools Nokia Customer Care Service Configuration 3: Covers-off Troubleshooting Using Service Jig Item Name Type 1 Service Jig MJ-42 2 DC Power Cable PCS-1 3 RF Test Cable XRS-6 4 Service M/FBUS Cable DAU-9S 5 Software Security Dongle PKD-1 6 Service Software for Level 3 service CDMA Phoenix Issue 1 03/2005 ©2005 Nokia Corporation Company Confidential Page 17
2115i/2116/2116i (RH-66) Service Tools Service Configuration 4: Automated Tuning and Alignment This setup is used for tuning of the handset at Nokia Authorized Service Centers.
