Nokia Customer Care Service Manual RH-70 (Nokia 1110) Mobile Terminal Part No: (9243364 (Issue 1, Part 1)) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Amendment Record Sheet Nokia Customer Care Amendment Record Sheet Amendment No Original issue Page ii Date 07/2005 Inserted By Comments G Rudh Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Copyright Nokia Customer Care Copyright Copyright © 2005 Nokia. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia, Nokia Connecting People, and Nokia X and Y are trademarks or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.
RH-70 Warnings and cautions Nokia Customer Care Warnings and cautions Warnings • IF THE DEVICE CAN BE INSTALLED IN A VEHICLE, CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND ANTI-SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE DEALER/ MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY.
RH-70 For your safety Nokia Customer Care For your safety QUALIFIED SERVICE Only qualified personnel may install or repair phone equipment. ACCESSORIES AND BATTERIES Use only approved accessories and batteries. Do not connect incompatible products. CONNECTING TO OTHER DEVICES When connecting to any other device, read its user’s guide for detailed safety instructions. Do not connect incompatible products. 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Care and maintenance Nokia Customer Care Care and maintenance This product is of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. • Keep the phone and all its parts and accessories out of the reach of small children. • Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits.
RH-70 ESD protection Nokia Customer Care ESD protection Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use. To replace the covers ESD protection must be applied. All electronic parts of the product are susceptible to ESD.
RH-70 Battery information Nokia Customer Care Battery information Note: A new battery's full performance is achieved only after two or three complete charge and discharge cycles! The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.
RH-70 Company Policy Nokia Customer Care Company Policy Our policy is of continuous development; details of all technical modifications will be included with service bulletins. While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing/e-mail.
RH-70 Company Policy Nokia Customer Care (This page left intentionally blank.) Page x Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia 1110 Service Manual Structure Nokia Customer Care Nokia 1110 Service Manual Structure 1 2 3 4 5 General information Parts and layouts Phoenix service software Service Tools Disassembly and reassembly instructions 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia 1110 Service Manual Structure Nokia Customer Care (This page left intentionally blank.) Page xii Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 1 — General information 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 General information Nokia Customer Care (This page left intentionally blank.) Page 1–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 General information Nokia Customer Care Table of Contents Product selection.............................................................................................................................................................................1–5 Display and keypad features.......................................................................................................................................................1–5 Features..............................................................
RH-70 General information Nokia Customer Care (This page left intentionally blank.) Page 1–4 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 General information Nokia Customer Care Product selection The RH-70 is a dual band transceiver unit designed for the GSM900 and GSM1800 networks.
RH-70 General information Nokia Customer Care UI features Messaging • Multimedia messaging: send and receive messages containing text, an audio clip, and an image to other compatible devices (maximum message size: up to 100kB) • SMS messaging • Predictive text input • Asia-Pacific: English, Chinese Simplified, Chinese Traditional, Thai, Philipino, Vietnamese, Bahasa Indonesia, Bahasa Malaysia, Hindi • Europe and Africa: Danish, Dutch, English, French, Finnish, German, Icelandic, Italian, Portugese, Spani
RH-70 General information Nokia Customer Care Table 2 Car Type Name CK-10 Nokia car kit HF-8 Nokia plug-in car handsfreet MP-2 Microphone CR-39 Nokia universal holder Table 3 Audio Type Name HDB-5 Boom Headset HDE-2 Headset HS-7 Dual Headset HDA-9 TTY Adapter Table 4 Xpress-on™ covers Type Name CC 232D EMEA colors: Gray, Blue, Orange, except APAC, which only have gray and blue.
RH-70 General information Nokia Customer Care Environmental conditions Environmental condition Ambient temperature Notes Normal operation -15 oC ... +55 oC Specifications fulfilled Reduced performance -30 ...15 oC and +55oC ... +70 oC Operational only for short periods Intermittent or no operation -40 oC ... -30 oC and +70 oC ... +85oC Operation not guaranteed but an attempt to operate will not damage the phone No operation or storage <-40 oC and >+85 oC No storage.
RH-70 General information Nokia Customer Care Voltage Voltage (V) Condition HW reset demands Min 1. 0V Max -- d a. The nominal voltage is defined as being 15% higher than the lower extreme voltage. TA will test with this nominal voltage at an 85% range (0.85x3.9V a 3.3V). b. This limit is set to be above SW shutdown limit in TA. c. During fast charging of an empty battery, this voltage might exceed this value. Voltages between 4.20 and 4.60 might appear for a short while. d.
RH-70 General information Nokia Customer Care (This page left intentionally blank.) Page 1–10 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 2 — Parts and layouts 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Parts and layouts Nokia Customer Care (This page left intentionally blank.) Page 2–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Parts and layouts Nokia Customer Care Table of Contents Exploded view..................................................................................................................................................................................2–5 Mechanical parts list.......................................................................................................................................................................2–6 Spare parts overview.........................................
RH-70 Parts and layouts Nokia Customer Care (This page left intentionally blank.) Page 2–4 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Parts and layouts Nokia Customer Care Exploded view Figure 2 Exploded view 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Parts and layouts Nokia Customer Care Mechanical parts list Table 7 Mechanical parts list ITEM/ CIRCUIT REF.
RH-70 Parts and layouts Nokia Customer Care Spare parts overview Figure 3 Spare parts overview 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Parts and layouts Nokia Customer Care SWAP phones Table 8 SWAP phones for RH-70 SWAP phones for RH-70 RH-70 SWAP ENGINE EURO-C RH-70 SWAP ENGINE EURO-C FRANCE RH-70 EURO-C TURKEY RH-70 SWAP ENGINE EURO-K RH-70 SWAP ENGINE UKR RH-70 SWAP ENGINE EURO-L SOUTH AFRICA RH-70 SWAP ENGING APAC-S, Singapore RH-70 SWAP ENGINE APAC-T, Philippines Component parts list Table 9 Component parts list Item ref PWB side X/Y Object name Value A7001 Top O 5 SHIELD_BB ~ A7002 Top J 6 SHIELD_RF_ASIC ~ A
RH-70 Parts and layouts Item ref PWB side Nokia Customer Care X/Y Object name Value C2151 Top N 7 CHIP ARRAY X5R 2X33N K 10V 0405 2x33n C2152 Top S 3 Chipcap 5% NP0 10p C2153 Bottom B 6 Chipcap 5% NP0 47p C2154 Bottom B 7 Chipcap 5% NP0 47p C2155 Top N 6 CHIP ARRAY X5R 2X33N K 10V 0405 2x33n C2157 Top O 8 Chipcap 5% NP0 100p C2159 Top N 7 CHIPCAP X7R 15N K 16V 0402 15n C2161 Top N 8 CHIPCAP X5R 100N M 16V 0402 100n C2164 Top N 6 CHIP ARRAY NP0 2X27P K
RH-70 Parts and layouts Nokia Customer Care Item ref PWB side X/Y Object name Value C2261 Top P 6 CHIPCAP X5R 4U7 K 10V 0805 4u7 C2287 Top M 5 CHIPCAP X5R 100N K 10V 0402 100n C2330 Top G 2 Chipcap 5% NP0 33p C2331 Top P 5 CHIPCAP X5R 1U K 6V3 0603 1u0 C2332 Top P 5 CHIPCAP X5R 4U7 K 10V 0805 4u7 C2400 Bottom U 4 CHIPCAP X5R 1U K 16V 0603 1u0 C2401 Bottom U 6 CHIPCAP X5R 1U K 6V3 0603 1u0 C2402 Bottom C 2 CHIPCAP X5R 100N K 10V 0402 100n C2403 Bottom C
RH-70 Parts and layouts Item ref PWB side Nokia Customer Care X/Y Object name Value C7628 Top J 5 Chipcap 5% NP0 56p C7630 Top K 6 Chipcap 5% NP0 22p C7631 Top D 3 CHIPCAP NP0 0P5 C 50V 0402 0p5 C7634 Top I 7 CHIPCAP X5R 100N K 10V 0402 100n C7635 Top K 6 CHIPCAP X5R 100N K 10V 0402 100n C7636 Top K 6 Chipcap +-0.
RH-70 Parts and layouts Nokia Customer Care Item ref PWB side X/Y Object name Value F2000 Top T 7 SM FUSE FF 2A 32V 0402 2.0A H2400 Bottom C 3 SM CONN BTB 2X5 F P0.5 ~ L2000 Top T 7 FERR.BEAD 0R03 42R/100MHZ 3A 0805 42R/100MHz L2001 Top R 3 CHIP BEAD ARRAY 2X1000R 0405 2x1000R/100MHz L2002 Top R 4 CHIP BEAD ARRAY 2X1000R 0405 2x1000R/100MHz L2170 Top S 3 FERRITE BEAD 0R5 600R/100MHZ 0603 600R/100MHz L2180 Top M 7 FERR.
RH-70 Parts and layouts Item ref PWB side Nokia Customer Care X/Y Object name Value R2013 Top R 5 CHIP VARISTOR VWM5.6V VC15.5 0402 5.6V/15V/0.05J R2020 Top R 5 ASIP 4XESD **PB-FREE** BGA5 ~ R2027 Top R 5 Resistor 5% 63mW 10k R2068 Top S 2 RES NETWORK 0W03 4X22R J 0804 4x22R R2069 Top S 2 Resistor 5% 63mW 1k0 R2070 Top S 2 CHIP VARISTOR VWM5.6V VC15.5 0402 5.6V/15V/0.
RH-70 Parts and layouts Nokia Customer Care Item ref PWB side X/Y Object name Value R7610 Top M 5 RES NETWORK 0W06 2X5K6 J 0404 2x5k6 R7611 Top M 5 RES NETWORK 0W06 2X5K6 J 0404 2x5k6 R7615 Top H 8 Resistor 5% 63mW 100R R7616 Top H 7 Resistor 5% 63mW 100R R7617 Top H 7 Resistor 5% 63mW 100R R7619 Top J 8 Resistor 5% 63mW 3k3 R7630 Top K 6 Resistor 5% 63mW 100k R7631 Top K 7 Resistor 5% 63mW 18k R7632 Top K 6 Resistor 5% 63mW 39R R7633 Top K 2 N
RH-70 Parts and layouts Item ref PWB side Nokia Customer Care X/Y Object name Value Z7602 Top H 7 SAW FILT 942.5+-17.5MHZ 2.0X1.6 942.5MHz Z7603 Top J 5 SILICON FILT 869.5+-45.5MHZ P-TSLP-7-4 869.
RH-70 Parts and layouts Nokia Customer Care (This page left intentionally blank.) Page 2–16 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 3 — Phoenix service software 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care (This page left intentionally blank.) Page 3–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care Table of Contents Introduction......................................................................................................................................................................................3–5 Read this first..............................................................................................................................................................................3–5 Service software installation.....................
RH-70 Phoenix service software Nokia Customer Care Figure 34 Add information for new user 1...........................................................................................................................3–21 Figure 35 Add information for new user 2...........................................................................................................................3–21 Figure 36 Login, user configured...........................................................................................
RH-70 Phoenix service software Nokia Customer Care Introduction Read this first The Phoenix software is used to a number of different phones containing different versions of baseband generations. These instructions are intended as a general guide and are not product specific, where a Phoenix SW version is shown you should use the relevant version for your product and in the screen shots where a type designator is shown you should read the type designator for your product.
RH-70 Phoenix service software Nokia Customer Care Installing Phoenix Before you begin • Check that a Dongle is attached to the parallel port of your computer. • Download the installation package (for example, phoenix_service_sw_a15_2004_24_7_55.exe) to your computer (in C:\TEMP, for instance). • Close all other programs. • Run the application file (for example, phoenix_service_sw_a15_2004_24_7_55.exe) and follow the instructions on the screen.
RH-70 Phoenix service software Nokia Customer Care Steps 1. Run the phoenix_service_sw_a15_2004_24_7_55.exe to start installation. Install Shield prepared the setup. Figure 7 Preparing setup Install Shield will prepare. 2. Click Next in Welcome dialog to continue. Figure 8 Welcome dialog 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care 3. Read the disclaimer carefully. Figure 9 Disclaimer text 4. Choose destination folder. The default folder C:\ProgramFiles\Nokia\Phoenix is recommended. Then click Next to continue. You may choose another location by selecting Browse (not recommended). Figure 10 Destination folder Page 3–8 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care 5. Wait for the components to be copied. The progress of the setup is shown in the Setup Status window. Figure 11 Installation status 1 6. Wait for the drivers to be installed and updated. The process may take several minutes to complete. If the operating system does not require rebooting (Windows 2000, XP) the PC components are registered right away. Figure 12 Installation status 2 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia.
RH-70 Phoenix service software Nokia Customer Care Figure 13 Registering components 1 If the operating system requires restarting your computer (Windows 98, SE, ME) the Install Shield Wizard will tell you about it. Select Yes... to reboot the PC immediately and No... to reboot the PC manually afterwards. Figure 14 Restart computer After the reboot, components are registered and Phoenix is ready for use. Note: Phoenix does not work, if components have not been registered.
RH-70 Phoenix service software Nokia Customer Care Figure 15 Registering components 2 7. Click Finish to end installation. Figure 16 Finish installation Phoenix is now ready for use. Next action Before using Phoenix Service Software, you must: • install phone model specific data package for Phoenix, and • configure users and connections. FPS-8* can be used after updating its Flash Update Package files.
RH-70 Phoenix service software Nokia Customer Care When you update Phoenix from old to new version (for example, a14_2004_16_4_47 to a15_2004_24_7_55), the update will take place automatically without uninstallation. If you try to update the Phoenix Service Software with the same version that you already have (for example, a15_2004_24_7_55 to a15_2004_24_7_55) you are asked if you want to uninstall the version of Phoenix you have on your PC.
RH-70 Phoenix service software Nokia Customer Care Figure 19 Uninstallation status 2. If the operating system does not require rebooting, click Finish to complete. Else, Install Shield Wizard will tell you about it. Select Yes... to reboot the PC immediately and No... to reboot the PC manually afterwards. Figure 20 Finish uninstallation 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care Figure 21 Restart computer Repairing Phoenix installation Context If you experience any problems with the service software, or suspect that files have been lost, you can use the repair function before completely reinstalling Phoenix. Note: The original installation package (for example, phoenix_service_sw_a15_2004_24_7_55.exe) must be found on your PC when you run the repair setup. Steps 1. Open Windows Control Panel → Add/Remove Programs . 2.
RH-70 Phoenix service software Nokia Customer Care Figure 22 Repair program 4. Click Finish to complete repair. Figure 23 Finish repair installation Phoenix service software data package overview Each product has its own data package (DP).
RH-70 Phoenix service software Nokia Customer Care Installing Phoenix data package Before you begin 1 Verify that The data package contains all product-specific data to make the Phoenix Service Software and tools usable with a certain phone model. 2 Check that the dongle is attached to the parallel port of your computer. 3 Install Phoenix Service SW. 4 Download the installation package (for example, RM-51_dp_EA_v_1_0.exe) to your computer (for example, in C:\TEMP). 5 Close all other programs.
RH-70 Phoenix service software Nokia Customer Care 3. Click Next to continue. Figure 25 Continue data package installation In this view you can see the contents of the data package. Read the text carefully. There should be information about the Phoenix version required with this data package. Click Next to continue. Figure 26 Data package setup information 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care 4. Confirm location and click Next to continue. Figure 27 Data package destination folder The install shield checks where the Phoenix application is installed and the directory is shown. Click Next to continue. 5. Click Next to start copying the files. Phone model specific files will be installed. Please wait. Figure 28 Start copying files Page 3–18 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care Figure 29 Data package installation status 6. Click Finish to complete the installation. Figure 30 Finish data package installation You now have all phone model specific files installed in your Phoenix Service SW. Next action Phoenix can be used, for example, for flashing phones and printing type labels. But first you must: • configure users, and • manage connections. FLS-4S can be used right away.
RH-70 Phoenix service software Nokia Customer Care Uninstalling Phoenix data package Context If you try to install the same version of Phoenix data package that you already have, you are asked if you want to uninstall the version you have on your PC. Older versions of data packages don´t need to be uninstalled unless instructions to do so are given in the readme.txt file of the data package and bulletins concerning the release. Please read all related documents carefully. Steps 1.
RH-70 Phoenix service software Nokia Customer Care Service software instructions Configuring users in Phoenix Steps 1. Start Phoenix Service SW and log in. If your user ID is already configured, choose it from the dropdown list and click OK. To add a new user or edit existing ones click Maintain. Figure 33 Login 2. Choose New to add information for a new user. Figure 34 Add information for new user 1 3. Type in your name and initials and click OK.
RH-70 Phoenix service software Nokia Customer Care 5. Click OK. Figure 36 Login, user configured Managing connections in Phoenix Steps 1. Start Phoenix Service SW and log in. Figure 37 Phoenix icon 2. Choose File → Manage Connections . Figure 38 Manage connections Existing connections can be selected, edited, deleted, and new ones created by using this dialog. Page 3–22 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care Figure 39 Connections list 3. Click Add to add a new connection, and select if you want to create it manually or by using the Connection Wizard. In the following dialogs you will be asked to select settings for the connection. If you use the Wizard, connect the tools and a phone to your PC and the wizard will automatically try to configure the correct connection. 4. Select Manual mode, and click Next to continue.
RH-70 Phoenix service software Nokia Customer Care ii For FPS-8 Flash Prommer, choose the following connection settings: • Media: FPS-8 • Port Num: COM Port where FPS-8 is connected • COMBOX_DEF_MEDIA: FBUS 5. Click Finish to complete the configuration. 6. Activate the connection you want to use by clicking it, use up/down arrows to move it on top of the list, and click Apply. Figure 42 Connections list The connection is now selected and can be used after closing the Manage Connections window.
RH-70 Phoenix service software Nokia Customer Care Figure 45 Product support module information Installing Flash support files for FPS-8* and FLS-4* Before you begin Note: This is a separate installation package. • Install Phoenix Service SW. • Install phone model specific data package for Phoenix. • The flash support files are delivered in the same installation package with Phoenix data packages or newer Phoenix packages since September 2003.
RH-70 Phoenix service software Nokia Customer Care 2. If the same version of Flash Update package already exists, and you want to reinstall it, the previous package is first uninstalled. Run the installation again. Figure 47 Uninstall flash update package If you try to downgrade the existing version to older ones, the setup will be aborted. If you really want to downgrade, uninstall newer files manually from Control Panel and then rerun the installation again.
RH-70 Phoenix service software Nokia Customer Care 3. It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia \Phoenix. Click Next to continue. Figure 50 Flash destination folder When installing the flash update files for the first time you may choose another location by selecting Browse. However, this is not recommended. Installation will continue. Figure 51 Flash installation status 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia.
RH-70 Phoenix service software Nokia Customer Care 4. Choose Finish to complete the installation procedure. Figure 52 Finish flash update Next action FLS-4 can be used right after the Flash Update Package is installed. FPS-8* flash prommer must be updated using Phoenix! Updating FPS-8 Flash prommer software Steps 1. Start Phoenix Service Software and log in, manage connection correctly for the FPS-8* flash prommer. Figure 53 Phoenix icon 2. Choose Flashing → FPS-8 Maintenance .
RH-70 Phoenix service software Nokia Customer Care 3. When the new FPS-8 flash update package is installed to computer you will be asked to update the files to your FPS-8 Prommer. Select Yes to update files. Figure 55 Prommer SW update 4. Wait until you are notified that update has been successful; the procedure will take a couple of minutes. Click OK to close the FPS-8 Maintenance window.
RH-70 Phoenix service software Nokia Customer Care Figure 57 FPS-8 info window Alternative steps • FPS-8 SW can also be updated by pressing Update button and selecting appropriate fps8upd.ini file in C: \Program Files\Nokia\Phoenix\Flash. Figure 58 Flash directory window • All files can be loaded separately to FPS-8. To do this, just press the right mouse button in the Flash box files window and select the file type to be loaded. More information can be found in Phoenix Help.
RH-70 Phoenix service software Nokia Customer Care When activation file is received (for example, 00000.in), copy it to C:\ProgramFiles\Nokia\Phoenix \BoxActivation directory on your computer (this directory is created when Phoenix is installed). Steps 1. Start Phoenix Service Software. 2. Select Flashing → FPS-8 maintenance . Figure 59 FPS-8 maintenance 3. Click Activate in the FPS-8 Maintenance window.
RH-70 Phoenix service software Nokia Customer Care 4. Click Open to activate the box. Figure 61 Box activation 5. Turn the FPS-8's power off and on to complete activation. Deactivating FPS-8 Context If there is, for example, a need to send the FPS-8 box for repair, it must be deactivated first. Steps 1. 2. 3. 4. Start Phoenix Service Software. Choose Maintenance → Prommer Maintenance . In the Prommer Maintenance window, click Deactivate. To confirm the deactivation, click Yes.
RH-70 Phoenix service software Nokia Customer Care Updating JBV-1 docking station software Before you begin The JBV-1 docking station contains software (firmware) which can be updated.
RH-70 Phoenix service software Nokia Customer Care 2. Read the instructions in the dialog box and click Next to continue. 3. Figure 64 JBV-1 update information Accept the suggested destination folder for installing the JBV-1 SW Package, and click Next to continue. 4. Figure 65 JBV-1 update destination folder Select Full installation and click Next to continue. Page 3–34 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software 5. Nokia Customer Care Figure 66 Select installation: Full A program folder is created and the software files are installed there. Click Next to continue. Figure 67 Select program folder 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Phoenix service software Nokia Customer Care 6. 7. 8. Click Finish to complete the installation. Figure 68 Finish JBV-1 update installation Connect the USB cable/JBV-1 to your computer. Connect power to JBV-1 (11-16V DC) from an external power supply, then connect the USB Cable between the JBV-1 USB connector and the PC. Install or update the JBV-1 USB drivers which are delivered with the JBV-1 SW installation package.
RH-70 Phoenix service software Nokia Customer Care 11. Choose file JBV1v18.CDE and click Open to update your JBV-1 to a new version (v.18). Figure 70 JBV-1 update directory window Wait until you hear a "click" from the JBV-1. The older SW file JBV1v17.CDE is visible in this view only if the previous JBV-1 SW package has been installed on your computer. 12. Click OK to see the current JBV-1 status (after a successful update).
RH-70 Phoenix service software Nokia Customer Care (This page left intentionally blank.) Page 3–38 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 4 — Service Tools 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Service Tools Nokia Customer Care (This page left intentionally blank.) Page 4–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Service Tools Nokia Customer Care Table of Contents Service tools......................................................................................................................................................................................4–5 ACF-8..............................................................................................................................................................................................4–5 AXS-4.................................................
RH-70 Service Tools Nokia Customer Care Figure 76 FPS-11 Prommer box flash concept.....................................................................................................................4–16 Figure 77 JBV-1 flash concept with FPS-10...........................................................................................................................4–16 Figure 78 JBV-1 flash concept with FPS-8.................................................................................................
RH-70 Service Tools Nokia Customer Care Service tools List of Service Tools The table below gives a short overview of service tools that can be used for testing, error analysis and repair of product , refer to various concepts. ACF-8 Universal power supply ACF-8 universal power supply is used to power FPS-8. ACF-8 has 6V DC and 2.1A output. AXS-4 Service cable The AXS-4 D9-D9 service cable is used to connect two 9 pin D connectors for example between PC and FPS-8. The cable length is 2 meters.
RH-70 Service Tools Nokia Customer Care CA-31D USB cable The CA-31D USB cable is used to connect FPS-10 or FPS-11 to a PC. It is included in the FPS-10 and FPS-11 sales packages. CA-35S Power cable Power cable for connecting e.g. the FPS-10 prommer box to the POS flash adapter. CA-41PS Power cable Power cable for connection of e.g. the JBV-1 docking station to the FPS10 prommer box.
RH-70 Service Tools Nokia Customer Care CA-65DS DS easy flash cable The CA-65 DS easy flash cable is used to connect the phone bottom connector to either POS flashing device (FLS-4S) or to the PROMMER box (FPS-11). CA-66DS Easy flash cable This cable connects the phone DC port to the FPS-8 prommer. CA-67DS Easy flash cable This cable connects the phone DC port to the FPS-10 prommer. DA-49 Docking station adapter The Docking Station adaptor is used for this phone in combination with JBV-1.
RH-70 Service Tools Nokia Customer Care FLC-2 DC cable FLC-2 is used with a flash adapter to supply a controlled operating voltage. FLS-4S Flash device FLS-4S is a dongle and flash device incorporated into one package, developed specifically for POS use.
RH-70 Service Tools Nokia Customer Care FPS-11 Parallel flash prommer FPS-11 interfaces with: • • • • PC Control unit Flash adapter Smart card FPS-11 flash prommer features: • • • • • • Can flash up to 8 phones at a time, controlled by one PC Communication method between PC and FPS-11 is single USB2.
RH-70 Service Tools Nokia Customer Care MJ-59 Module jig MJ-59 is meant for component level troubleshooting. The jig includes an RF interface for GSM. PCS-1 Power cable The PCS-1 power cable (DC) is used with a docking station, a module jig or a control unit to supply a controlled operating voltage. PKD-1 SW security device SW security device is a piece of hardware enabling the use of the service software when connected to the parallel (LPT) port of the PC.
RH-70 Service Tools Nokia Customer Care RJ-79 Soldering jig The soldering jig RJ-79 is used for soldering and as a rework jig for system module. It is made of lead-free rework compatible material. SA-41 RF Coupler SA-41 RF Coupler is used for Go/No-Go test after changing components in the RF part of the phone. The SA-41 is mounted on the docking station adapter. Note: For RF attenuation values, please refer to the Service bulletin.
RH-70 Service Tools Nokia Customer Care SRT-6 Opening tool SS-54 Alignment Jig Alignment jig is used to efficiently assemble the dome-sheet to the pone's PWB. The jig is made of EDS proof material. ST-30 Rework stencil Rework stencil to be used together with RJ-51 to rework the Front End Module (FEM) ST-32 Rework stencil for N7600 Rework stencil to be used together with RJ-72 for rework of N7600.
RH-70 Service Tools Nokia Customer Care XCS-4 Modular cable XCS-4 is a shielded (one specially shielded conductor) modular cable for flashing and service purposes. XRF-1 RF cable The RF cable is used to connect, for example, a module repair jig to the RF measurement equipment. SMA to N-Connector ca. 610mm. Attenuation for: • GSM850/900: 0.3+-0.1 dB • GSM1800/1900: 0.5+-0.1 dB • WLAN: 0.6+-0.1dB 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Service Tools Nokia Customer Care Service software concept POS (Point of Sales) flash concept Figure 73 POS flash concept Item Description Type 1 Phone 2 Battery 3 Easy flash cable CA-65DS 4 FLS-4S sales pack FLS-4S 5 AC charger ACF-8 6 PC with Service SW CD-ROM Page 4–14 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Service Tools Nokia Customer Care FPS-8 Prommer box flash concept Figure 74 FPS-8 Prommer box flash concept Item Description Type 1 Phone 2 Battery 3 Service cable CA-66DS 4 Flash prommer box sales pack including 2 pcs SF12 SRAM FPS-8 5 AC Charger, included in FPS-8 sales package ACF-8 6 RS-232 (D9 – D9) cable, included in FPS-8 sales pack AXS-4 7 Printer cable, included in FPS-8 sales package 8 Software protection key 9 PC with service SW 9243364 (Issue 1, Part 1) Company
RH-70 Service Tools Nokia Customer Care FLS-10 Prommer box flash concept Figure 75 FPS-10 Prommer box flash concept Item Description Type 1 Battery 2 Phone 3 Service cable CA-67DS 4 Flash prommer box sales pack FPS-10 5 Power supply, included in FPS-10 sales package AFC-8 6 USB A to B cable CA-31D 7 Software protection key PKD-1 8 Service SW (PHOENIX) Page 4–16 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Service Tools Nokia Customer Care FLS-11 Prommer box flash concept Figure 76 FPS-11 Prommer box flash concept Item Description Type 1 Phone 2 Battery BL-5C 3 DC power cable CA-65DS 4 Flash prommer box sales pack FPS-11 5 Power supply, included in FPS-11 sales package 6 USB A to B cable CA-31D 7 Software protection key PKD-1 8 Service SW (PHOENIX) 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Service Tools Nokia Customer Care JBV-1 flash concept with FPS-10 Figure 77 JBV-1 flash concept with FPS-10 Item Description Type 1 Docking station JBV-1 2 Docking station adapter DA-49 3 DC power cable CA-41PS 4 Modular cable XCS-4 5 Flash prommer box sales pack FPS-10 6 Power supply, included in FPS-10 sales package AFC-8 7 USB A to B cable CA-31D 8 Software protection key PKD-1 9 Service SW (PHOENIX) Page 4–18 Company Confidential Copyright ©2005 Nokia.
RH-70 Service Tools Nokia Customer Care JBV-1 flash concept with FPS-8 Figure 78 JBV-1 flash concept with FPS-8 Item Description Type 1 Docking station JBV-1 2 Docking station adapter DA-49 3 DC power cable PCS-1 4 Modular cable XCS-4 5 Flash prommer box sales pack FPS-8 6 Power supply, included in FPS-8 sales package AFC-8 7 RS-232 (D9 – D9) cable, included in FPS-8 sales package AXS-4 8 Printer cable, included in FPS-8 sales package 9 Software protection key 10 Service SW (
RH-70 Service Tools Nokia Customer Care Module jig (MJ-59) service concept Figure 79 Module jig service concept Item Description Type 1 Module jig MJ-59 2 RF test cable XCF-4 3 Service MBUS/FBUS cable DAU-9S 4 DC power cable PCS-1 5 Software protection key PKD-1 6 PC with Service SW (PHOENIX) Page 4–20 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 5 — Disassembly and reassembly instructions 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care RH-70 Disassembly and reassembly instructions (This page left intentionally blank.) Page 5–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Disassembly and reassembly instructions Nokia Customer Care Table of Contents Disassembly instructions..............................................................................................................................................................5–5 Reassembly instructions...............................................................................................................................................................
Nokia Customer Care RH-70 Disassembly and reassembly instructions (This page left intentionally blank.) Page 5–4 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Disassembly and reassembly instructions Nokia Customer Care Disassembly instructions Steps 1. Tools needed for disassembly and reassembly. 2. Protect the window with a film. 3. Press the release button and remove the B-cover. 4. Use the STR-6 to unlock the A-cover on both sides. 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Disassembly and reassembly instructions Nokia Customer Care 5. Remove the A-cover. When reassembling the A-cover, always start on the top side of the device. 6. Use the SRT-6 to remove the keymat and protect the inner side of the window with a film. 7. Note: For reassembly only! Fit the keymat to the A-cover, paying attention to its correct position. 8. Unscrew the six Torx Plus size 6 screws in the shown order.
RH-70 Disassembly and reassembly instructions 9. Nokia Customer Care Lift the LCD shielding while carefully pressing on the LCD module with a clean cloth. 10. Remove the LCD shielding. 11. Remove the acoustic channel. 12. Protect the LCD module with a film. 9243364 (Issue 1, Part 1) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Disassembly and reassembly instructions Nokia Customer Care 13. Take care of the surrounding components when opening the LCD connector. 14. Use the SRT-6 to open the LCD connector in the shown order. Be extra careful with the flex foil of the LCD module. 15. Remove the LCD module. 16. Remove the light guide assembly. Page 5–8 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Disassembly and reassembly instructions Nokia Customer Care 17. Lift the engine module a bit with the SRT-6 and remove it from the D-cover assembly. 18. The antenna IHF assembly drops out when turning the D-cover assembly. 19. Press out the Easy Flash connector by using the DC-plug. 20. Remove the microphone with the slotted screwdriver. Reassembly instructions For reassembly, follow the instructions for disassembly, but in reversed order. Note: Pay extra attention to steps 8,7 and 5.
Nokia Customer Care RH-70 Disassembly and reassembly instructions (This page left intentionally blank.) Page 5–10 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care Service Manual RH-70 (Nokia 1110) Mobile Terminal Part No: (9243364 (Issue 1, Part 2)) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia Customer Care (This page left intentionally blank.) Page ii Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia 1110 Service Manual Structure Nokia Customer Care Nokia 1110 Service Manual Structure 1 Baseband troubleshooting 2 RF troubleshooting 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia 1110 Service Manual Structure Nokia Customer Care (This page left intentionally blank.) Page iv Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 1 — Baseband troubleshooting 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care (This page left intentionally blank.) Page 1–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Table of Contents General baseband troubleshooting..........................................................................................................................................1–5 Phone is dead.............................................................................................................................................................................1–5 Flash programming do not work................................................
RH-70 Baseband troubleshooting Nokia Customer Care Figure 22 Headset earpiece fault flow chart........................................................................................................................1–23 Figure 23 Microphone fault flow chart..................................................................................................................................1–24 Figure 24 Headset microphone fault flow chart..........................................................................
RH-70 Baseband troubleshooting Nokia Customer Care General baseband troubleshooting Phone is dead Context This means that the phone does not use any current at all when the supply is connected and/or power key is pressed. It is assumed that the voltage supplied is 3.6VDC. The UEMCLite will prevent any functionality at battery/ supply levels below 2.9VDC. 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Context Figure 1 Phone is dead troubleshooting Flash programming do not work The flash programming can be done via the pads on the PWB (J2060). Page 1–6 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care In case of Flash failure in FLALI station, swap the phone and send it back to the care program for further analysis. Possible failures could be short-circuit of balls under µBGAs (UEMCLite, UPP4M, FLASH). Missing or misaligned components. In flash programming error cases the flash prommer can give some information about a fault.
RH-70 Baseband troubleshooting Nokia Customer Care Easy flash programming does not work The flash programming can also be done via the easy flash connector. In case of Flash failure in FLALI station, swap the phone and send it back to the care program for further analysis. Possible failures could be short-circuit of balls under µBGAs (UEMCLite, UPP4M, FLASH). Missing or misaligned components. In flash programming error cases the flash prommer can give some information about a fault.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 3 Easy flash programming fault Power does not stay on or the phone is jammed If this kind of a failure is presenting itself immediately after FLALI, it is most likely caused by ASIC's missing contact with PWB. If the MCU doesn’t service the watchdog register within the UEMCLite, the operations watchdog will run out after approximately 32 seconds. Unfortunately, the service routine can not be measured.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 4 Power does not stay on or the phone is jammed Display shows "Contact Service" This error can only happen at power up where several self-tests is run. If any of these test cases fails the display will show the message: "Contact Service". It's individual test cases so the below lineup of error hunting's has no chronological order. Use common sense and experience to decide which test case to start error hunting at.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 5 Troubleshooting when the "Contact Service" message is seen The phone does not register to the networks, or the phone can not make a call If the phone doesn't register to the network, the fault can be in either BB or RF. Only few signals can be tested since several signals is 'buried' in one or more of the inner layers of the PWB. First of all check that SIM LOCK is not causing the error by using a Test-SIM card and connect the phone to a tester.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 6 No registering or call SIM related faults Insert SIM card fault The hardware of the SIM interface from UEMCLite (D2200) to the SIM connector (X2700) can be tested without a SIM card. When the power is switched on the phone first check for a 1.8SIM card and then a 3V SIM card. The phone will try this four times, where after it will display ”Insert SIM card”. Page 1–12 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 7 Insert SIM card fault Figure 8 Signal diagram SIM card rejected The error ”SIM card rejected” means that the ATR message received from SIM card is corrupted, e.g. data signal levels are wrong. The first data is always ATR and it is sent from card to phone. For reference a picture with normal SIM power-up is shown below. 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 9 Signal diagram User interface Blank display The display does not show any information at all. Figure 10 Blank display Display is corrupt The display contains missing or fading segments or color presentation is incorrect. Page 1–14 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 11 Display is corrupt Dead keys Not a single key is responding. Figure 12 Dead keys No backlight for display or keys There is no backlight on the display or on the keys. 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 13 No backlight for display or keys Page 1–16 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Audio troubleshooting Audio troubleshooting using phoenix Figure 14 Phoenix audio test window 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 15 PWB audio test points Check microphone using "Hp microphone in Ext speaker out" loop Steps 1. 2. 3. 4. 5. 6. Connect phone with Phoenix. Open “audio test” window from “Testing -> Audio test”, as shown in Figure Phoenix audio test window above. Select “Hp microphone in Ext speaker out” Select “Loop” as “On” Input sound at microphone port, for example 94 dB SPL 1 kHz.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 16 Test arrangement for microphone Check earpiece using "Ext microphone in Hp speaker out" loop Steps 1. 2. 3. 4. 5. 6. Connect phone with Phoenix. Open “audio test” window from “Testing -> Audio test”, as shown in Figure Phoenix audio test window above. Select “Ext microphone in Hp speaker out” Select “Loop” as “On” Input signal to XMICP/N pads, as shown in Figure PWB audio test points above, for example 100 mVpp, 1 kHz.
RH-70 Baseband troubleshooting Nokia Customer Care Figure 18 Checking IHF and ring tone by using "Buzzer" Check vibra function using "Vibra control" Steps 1. 2. 3. 4. 5. 6. Connect phone with Phoenix. Open “Vibra control” window from “Testing -> Vibra control”, as shown in the figure below. Select suitable intensity value, for example 53 %. Select “Vibra state” as “Enabled” Click “Write”. Check if Vibra works.
RH-70 Baseband troubleshooting Nokia Customer Care Earpiece fault Figure 20 Earpiece fault flow chart 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care IHF/ringing tone fault Figure 21 IHF/ringing tone fault flow chart Page 1–22 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Headset earpiece fault Figure 22 Headset earpiece fault flow chart 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Microphone fault Figure 23 Microphone fault flow chart Page 1–24 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care Headset microphone fault Figure 24 Headset microphone fault flow chart 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Baseband troubleshooting Nokia Customer Care (This page left intentionally blank.) Page 1–26 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 2 — RF troubleshooting 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care (This page left intentionally blank.) Page 2–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Table of Contents General RF troubleshooting.........................................................................................................................................................2–5 General RF troubleshooting...................................................................................................................................................2–5 RF key components......................................................................
RH-70 RF troubleshooting Nokia Customer Care Figure 53 VC1, VC2, VC3 signals.................................................................................................................................................2–24 Figure 54 TXP signal.....................................................................................................................................................................2–25 Figure 55 TXC signals at PCL0.................................................................
RH-70 RF troubleshooting Nokia Customer Care General RF troubleshooting General RF troubleshooting Most RF semiconductors are static discharge sensitive Two types of measurements are used in the following. It will be specified if the measurement type is "RF" or "LF". • RF measurements are done with a Spectrum Analyzer and a high-frequency 500 ohm passive probe, for example HP54006A. (Note that when measuring with the 500 ohm probe the signal will be around 20 dB attenuated.
RH-70 RF troubleshooting Nokia Customer Care Figure 26 Supply points at UEM (D2200) Figure 27 Supply point at RF IC (N7600) Auto tuning Context This phone can be tuned automatically. Autotune is designed to align the phone's RF part easier and faster. It performs calibrations, tunings and measurements of RX and TX. The results are displayed and logged in a result file, if initiated.
RH-70 RF troubleshooting Nokia Customer Care Figure 28 Auto tuning concept with CMU200 Figure 29 Auto tuning concept with RX and TX tuning devices and splitter Copy the two phone specific ini-files, for example rm_13_tunings.ini and autotune_RM-13.ini, to a phone specific folder, for example \Phoenix\products\RM-13\. Steps 1. Make sure the phone (in the jig) is connected to the equipment. Else, some menus will not be shown in Phoenix. 2.
RH-70 RF troubleshooting Nokia Customer Care 4. Wait a while for the PC to read the information from the phone. 5. Select Testing and RF Controls. 6. Set the parameters as follows: i Active Unit: RX ii Band: GSM 900 iii Operation Mode: Continuous mode iv RX/TX Channel 37 v AGC: 8: FEG_ON + DTOS_ON+BB_6=Vgain_36 7. The setup should now look like this: Figure 30 GSM 900 RF controls window Page 2–8 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Troubleshooting diagram for GSM 900 receiver Figure 31 GSM 900 Receiver troubleshooting By measuring with an oscilloscope at RXIP or RXQP on a working GSM900 receiver this picture should be seen. Signal amplitude 114mVp-p. DC offset 1.0V. 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Results Figure 32 900 RX I/Q signal waveform General instructions for GSM 1800 RX troubleshooting Steps 1. 2. 3. 4. 5. 6. Connect the phone to a PC with the module repair jig. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. Select File and Scan product. Wait a while for the PC to read the information from the phone. Select Testing and RF Controls.
RH-70 RF troubleshooting Nokia Customer Care 7. The setup should now look like this: Figure 33 GSM 1800 RF controls window 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Troubleshooting diagram for GSM 1800 receiver Figure 34 GSM 1800 Receiver troubleshooting By measuring with an oscilloscope at RXIP or RXQP on a working GSM1800 receiver this picture should be seen. Signal amplitude 114mVp-p. DC offset 1.0V. Page 2–12 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Results Figure 35 1800 RX I/Q signal waveform Measurement points in the receiver Figure 36 RX measurements point of the control voltages to FEM N7700 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 37 Measurement points at the RX SAW Filters – Z7600/Z7602 Figure 38 RX I/Q signals Transmitter General instructions for GSM 900 TX troubleshooting Steps 1. Apply a RF-cable to the RF-connector to allow the transmitted signal act as normal. RF-cable should be connected to an attenuator at least 10dB before connected to the measurement equipment, otherwise the PA may be damaged. 2.
RH-70 RF troubleshooting Nokia Customer Care ii Active Unit: RX iii TX Power Level: 5 iv TX Data Type: Random 7. The setup should now look like this: Figure 39 GSM 900 RF controls window 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Troubleshooting diagram for GSM 900 transmitter Figure 40 GSM 900 transmitter troubleshooting Measure the output power of the phone; it should be about 32.5dBm. Remember the cable loss is about 0.3dB. Page 2–16 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 41 TX I/O signal Figure 42 VC1, VC3 signals 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 43 TXP signal Figure 44 TXC signals at PCL5 GSM 900 TX output power Measure the output power of the phone; it should be about 32.5 dBm. Remember the cable loss is about 0.3 dB. Page 2–18 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 45 TX I/O signal Figure 46 VC1, VC3 signals 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 47 TXP signal Figure 48 TXC signals at PCL5 Page 2–20 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 49 TXC signals at PCL19 General instructions for GSM 1800 TX troubleshooting Steps 1. Apply a RF-cable to the RF-connector to allow the transmitted signal act as normal. RF-cable should be connected to an attenuator at least 10dB before connected to the measurement equipment, otherwise the PA may be damaged. 2. Start Phoenix and establish a connection to the phone with the data cable e.g. FBUS. 3. Select File and Scan product. 4.
RH-70 RF troubleshooting Nokia Customer Care 7. The setup should now look like this: Figure 50 GSM 1800 RF controls window Page 2–22 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Troubleshooting diagram for GSM 1800 transmitter Figure 51 GSM 1800 transmitter troubleshooting Measure the output power of the phone; it should be about 29.5dBm. Remember the cable loss is about 0.5dB. 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Results Figure 52 TX I/O signal Figure 53 VC1, VC2, VC3 signals Page 2–24 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 54 TXP signal Figure 55 TXC signals at PCL0 GSM 1800 TX output power Measure the output power of the phone; it should be about 29.5 dBm. Remember the cable loss is about 0.5 dB. 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 56 TX I/O signal Figure 57 VC1, VC2, VC3 signals Page 2–26 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 58 TXP signal Figure 59 TXC signals at PCL0 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 60 TXC signals at PCL15 Synthesizer troubleshooting Introduction There is only one PLL synthesizer generating Local Oscillator frequencies for both RX and TX in both bands (PCN and EGSM). The VCO frequency is divided by 2 for PCN operation or by 4 for EGSM operation inside the RF IC. The 26MHz oscillator is located near the RF IC (N7600). The coarse frequency for this oscillator is set by an external crystal (B7600).
RH-70 RF troubleshooting Nokia Customer Care Figure 61 PLL Troubleshooting diagram The 26MHz signal from the VCXO can be measured by probing R2900. The level at this point is approx. 770mVpp. Frequency of this oscillator is adjusted by changing the AFC-register inside the UEM IC. Example Signal Measured at VCXO output (R2900). 9243364 (Issue 1, Part 2) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 RF troubleshooting Nokia Customer Care Figure 62 VCXO 26 MHz waveform Figure 63 Measurement point for VCXO Page 2–30 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care Service Manual RH-70 (Nokia 1110) Mobile Terminal Part No: (9243364 (Issue 1, Part 3)) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia Customer Care (This page left intentionally blank.) Page ii Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia 1110 Service Manual Structure Nokia Customer Care Nokia 1110 Service Manual Structure 1 System module 2 Schematics 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Nokia 1110 Service Manual Structure Nokia Customer Care (This page left intentionally blank.) Page iv Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care 1 — System module 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 System module Nokia Customer Care (This page left intentionally blank.) Page 1–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 System module Nokia Customer Care Table of Contents Block diagram..................................................................................................................................................................................1–5 System module block diagram.............................................................................................................................................1–5 Functional description...............................................................
RH-70 System module Nokia Customer Care Figure 5 4-pole jack plug for audio accessory.....................................................................................................................1–11 Figure 6 Keyboard schematics..................................................................................................................................................1–17 Figure 7 Keyboard layout in UI side.........................................................................................
RH-70 System module Nokia Customer Care Block diagram System module block diagram The main board consists of a radio frequency part and a baseband part. The User Interface parts are situated at the UI side, which is on the opposite side of the engine board. The 1MF is the system module of the mobile device. Figure 1 Module block diagram 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 System module Nokia Customer Care Functional description The BB core is based on UPP4M CPU. UPP4M takes care of all the signal processing and operation controlling tasks of the mobile device. For power management, there is one main ASIC for controlling, charging and supplying power UEMCLite plus a discrete power supply. The UEMCLite generates the main reset for the system. Memories comprise 128 Mbit flash and 16 Mbit PsRAM. Memory devices are stacked on top of each other in a single Combo package.
RH-70 System module Nokia Customer Care Table 1 RF power supply Vmin/V Vtyp/V Vmax/V ItypmA Imax mA Notes VR1 2.7 2.78 2.86 65 75 VTX (Supply voltage for PMB3258 LO and RX parts VR2 2.7 2.78 2.78 2.4 3.0 VXO (VCXO supply voltage) VR3 2.7 2.78 2.86 41 47 VTX2 (Supply voltage for PMB3258 modulator output stage) VR4 2.7 2.78 2.86 43 48 VRX (Supply for RFIC RX and TX parts) VR5 2.7 2.78 2.86 29 35 VPLL (Supply for VCO, PLL and digital parts VBATTRF 3.1 3.6 4.7 1.5 3.
RH-70 System module Nokia Customer Care Figure 2 Power connection diagram All connectors going to the “outside world” have filter components, ESD protection and EMC reduction. The Digital/Data lines on SIM have special dedicated filter ASIP. The below figure show the SIM filtering.
RH-70 System module Nokia Customer Care • No supply: In NO_SUPPLY mode, the phone has no supply voltage. This mode is due to disconnection of main battery or low battery voltage level in battery. Phone is exiting from NO_SUPPLY mode when sufficient battery voltage level is detected. Battery voltage can rise either by connecting a new battery with VBAT > VMSTR+ or by connecting charger and charging the battery above VMSTR+.
RH-70 System module Nokia Customer Care Figure 4 Audio block diagram UEMCLite supports three microphone inputs and two earphone outputs. The microphone signals from different sources are connected to separate inputs at the UEMCLite ASIC. The inputs and outputs are all differential. Three inputs (MIC1, MIC2, MIC3) and two outputs (EAR, HF/HFCM) are used. MIC1P/MIC1N input is used for the internal microphone, using single-ended biasing circuitry. EARP/EARN output from UEMCLite is used for handportable mode.
RH-70 System module Nokia Customer Care External audio connector The system connector, containing a 4-pole Jack plug, gains the access to the external audio interface. The Jack plug, which is integrated in the system connector, contains a mechanical switch, which is used to detect the connection of the accessories. The configuration for the 4-pole Jack-plug is shown in the following figure.
RH-70 System module Nokia Customer Care Signal From XEARP HS/HF XEARN EAR/ Amp. INT HEADINT VCHARIN To Min Nom Max Condi-tion Note UEMC Lite 100 mV diff Ana in Quasi-differential DCcoupled earpiece/HF amplifier signal to accessory. DC biased to 0.8V Switch UEMC Lite 0/2.7V Dig in HS interrupt from bottom connector switch when plug inserted. Charger UEMC Lite 11.1Vp eak Standard Vch from Charger Connector, max 20V 16.9 Vpeak 7.9 VRMS 1.0 Apeak 7.0 VRMS 8.4 VRMS 9.
RH-70 System module Signal name Nokia Customer Care From To Para-meter Input characteristics Min TXP2 UPP RF-IC (GenIO6) RFBusEn1 X UPP RF-IC 1.88 V 0 0 0.4 V Load Resistance 10 RFBusClk UPP 9243364 (Issue 1, Part 3) RF IC Depends of the RF design kW Load Capacitance 20 pF Timing Accuracy ¼ symbol 1 1.38 1.88 V 0 0 0.4 V 50 uA 10 Load capacitance RF- IC/ UPP Unit 1.
RH-70 System module Nokia Customer Care Signal name From To Para-meter Input characteristics Min GENIO3 UEMCLite RF IC 1 Typ 2.78 UEMCLite RF IC RF Control * 0 V Depends of the RF design Load resistance kW 1 4 2.78 UEMCLite RF IC V V Load resistance kW 1 4 2.
RH-70 System module Nokia Customer Care Analogue Signals Table 7 AC and DC Characteristics of RF-Base band Analogue Signals Signal name RFCLK From VCTCXO To UPP Parameter Min Frequency Typ 13/26 Signal amplitude 0.2 Input Impedance 10 0.8 200 Duty Cycle 40 60 RF-IC UEMCL ite Voltage swing (static) 1.4 1.35 DC level 1.3 I/Q amplitude mismatch TXIN, TXQP, TXQN % V System Clock slicer Ref GND, not separated from pwb GND layer 1.
RH-70 System module Nokia Customer Care Signal name AFC From To Parameter UEMCLite VCTCX O Voltage Min 0.0 0.1 Max 2.4 2.55 (AFCOUT ) Min Resolution Load resistance UEMCLite RF-IC (AUXOUT ) 11 PATEMP RF-IC UEMCL ite Function Automatic Frequency Control signal for VCTCXO Programmable kW nF Source Impedance 200 W 10 Voltage Min Max UEMCL ite V 100 MW Path powered down 0.1 V 200 W Transmitter power level and ramping control, Ref UEMCLite RF converter specification 2.
RH-70 System module Nokia Customer Care Figure 6 Keyboard schematics The layout is shown in Keyboard layout in UI side. Figure 7 Keyboard layout in UI side SIM interface The SIM interface is programmed to support 3V and 1.8V SIMs. SIM supply voltage is selected by with register in the UEMCLite. It is only allowed to change the SIM supply voltage when the SIM IF is powered down. The SIM power up/down sequence is generated in the UEMCLite.
RH-70 System module Nokia Customer Care Table 8 The electrical parameters Pin Name Parameter Min Typ Max Unit 1 VSIM 1.8V SIM Card 1.6 1.8 1.9 V 3V SIM Card 2.8 3.0 3.2 V 1.8V SIM Card 0.9xVSIM VSIM V 0 0.15xVSIM 0.9xVSIM VSIM 0 0.15xVSIM 2 SIMRST 3V SIM Card 3 SIMCLK Frequency 3.25 Trise/Tfall 4 DATA 5 NC 6 GND Notes Supply voltage SIM reset (output) V MHz 50 ns VSIM V VSIM V SIM clock. UPP4Mv3 and UPP4mv4 support 3GPP Release 5, SIMCLK/8 data rate.
RH-70 System module Nokia Customer Care External signals and connections Table 9 System connector Signal XMICP From HS/HF Mic To Min UEMC Lite Nom Max 2/60mV diff Condi-tion Note Analog audio in Headset Mic bias and audio signal 2mV nominal. HF Mic signal 60mV nominal. Differential symmetric input.
RH-70 System module Nokia Customer Care Signal From To Min Nom Max Condi-tion Note BSI UEMCLite 0 2.78 Analog input, Battery Size Indicator Resistor, 100 kohm pull up to 2.78V (VBB1). FDL Init, refer to flash download. BTEMP UEMCLite 0 2.78 Btemp NTC Resistor, 100 kohm pull up to 2.78V (VANA) * Note! In BL-5C battery IF the BTEMP signal doesn’t exists. Temperature measurement is done on system board with NTC resistor.
RH-70 System module Nokia Customer Care PWB outline Figure 10 PWB top side component placement RF description Frequency band, power and multi-slot class The requirements leads to the specification in the table below: Table 11 Frequency bands and TX power class System GSM900 Frequency band Tx: 880 – 915 MHz TX power class 4 (33dBm) Rx: 925 – 960 MHz GSM1800 Tx: 1710 – 1785 MHz 1 (30dBm) Rx: 1805 – 1880 MHz Table 12 Multi-slot class Multislot Class GPRS MSC 6 (up to 3+1 and 2+2) Transmitter - gene
RH-70 System module Nokia Customer Care The two control methods used are open-loop Vcc control (RFMD) and feedback control with current sensing (Renesas, Philips). The reference waveform (TXC) for the control loop comes from the baseband. The output of the PA goes into a low pass filter located inside the FEM (Front End Module). Finally the transmit signal goes through the band selection and TX/RX switches to the antenna port.
Nokia Customer Care 2 — Schematics 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Schematics Nokia Customer Care (This page left intentionally blank.) Page 2–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Schematics Nokia Customer Care Table of Contents Schematics.........................................................................................................................................................................................2–4 List of Figures Figure 11 UPP, UEM, Combo memory, Radio, SIM (1jv_50e)...............................................................................................2–4 Figure 12 UI, keyboard, Audio (1jv_50e)...............................................
RH-70 Schematics Nokia Customer Care Schematics UPP, UEM, Combo memory, Radio, SIM Figure 11 UPP, UEM, Combo memory, Radio, SIM (1jv_50e) 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Schematics Nokia Customer Care UI, keyboard, Audio Figure 12 UI, keyboard, Audio (1jv_50e) 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Schematics Nokia Customer Care RF part Figure 13 RF part (1jv_50e) 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Schematics Nokia Customer Care Signal overview Figure 14 Signal overview (1jv_50e) 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Schematics Nokia Customer Care Component finder Figure 15 Component finder (1jv_50e) 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
Nokia Customer Care Glossary 9243364 (Issue 1, Part 3) Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Glossary of terms Nokia Customer Care (This page left intentionally blank.) Page Glossary–2 Company Confidential Copyright ©2005 Nokia. All Rights Reserved.
RH-70 Glossary of terms Nokia Customer Care A/D-converter Analog-to-digital converter ACI Accessory Control Interface ADC Analog-to-digital converter ADSP Application DPS (expected to run high level tasks) AGC Automatic gain control (maintains volume) ALS Ambient light sensor AMSL After Market Service Leader ARM Advanced RISC Machines ARPU Average revenue per user (per month or per year) ASIC Application Specific Integrated Circuit ASIP Application Specific Interface Protector B2B B
RH-70 Glossary of terms Nokia Customer Care DPLL Digital Phase Locked Loop DSP Digital Signal Processor DtoS Differential to Single ended EDGE Enhanced data rates for global/GSM evaluation EGSM Extended GSM EM Energy management EMC Electromagnetic compability EMI Electromagnetic interference ESD Electrostatic discharge FCI Functional cover interface FPS Flash Programming Tool FR Full rate FSTN Film compensated super twisted nematic GND Ground, conductive mass GPIB General-purpo
RH-70 Glossary of terms Nokia Customer Care LPRF Low Power Radio Frequency MCU Micro Controller Unit (microprocessor) MCU Multiport control unit MIC, mic Microphone MIDP Mobile Information Device Profile MIN Mobile identification number MIPS Million instructions per second MMC Multimedia card MMS Multimedia messaging service NTC Negative temperature coefficient, temperature sensitive resistor used as a temperature sensor OMA Object management architechture OMAP Operations, maintenan
RH-70 Glossary of terms Nokia Customer Care SARAM Single Access RAM SAW filter Surface Acoustic Wave filter SDRAM Synchronous Dynamic Random Access Memory SID Security ID SIM Subscriber Identity Module SMPS Switched Mode Power Supply SNR Signal-to-noice ratio SPR Standard Product requirements SRAM Static random access memory STI Serial Trace Interface SW Software SWIM Subscriber/Wallet Identification Module TCXO Temperature controlled Oscillator Tiku Finnish for Chip, Successor o