Nokia MetroSite EDGE Base Station Solution Accessories DN99252966 Issue 3-0 en © Nokia Corporation Nokia Proprietary and Confidential Draft 1 (66)
Solution Accessories The information in this documentation is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia's customers only for the purposes of the agreement under which the documentation is submitted, and no part of it may be reproduced or transmitted in any form or means without the prior written permission of Nokia.
0523 FCC Hereby, Nokia Corporation, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive: 1999/5/EC. The product is marked with the CE marking and Notified Body number according to the Directive 1999/5/EC. FCC §15.21 - Information to user - This product is used as an intentional radiated equipment and any changes or modifications on the equipment without any approval by Nokia could void the user's authority to operate the equipment. FCC §15.
Solution Accessories 4 (66) © Nokia Corporation Nokia Proprietary and Confidential Draft DN99252966 Issue 3-0 en
Contents Contents 5 List of tables 7 List of figures 9 Summary of changes 11 1 About this document 13 2 2.1 2.1.1 2.1.2 2.2 2.2.1 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.4 2.4.1 2.4.2 2.4.3 2.4.4 2.4.5 2.4.6 2.5 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.7 2.7.1 2.7.2 2.7.3 2.7.4 2.7.5 2.8 2.8.1 2.8.2 2.8.3 2.8.4 2.8.
Solution Accessories 6 (66) © Nokia Corporation Nokia Proprietary and Confidential Draft DN99252966 Issue 3-0 en
List of tables Table 1. Flexbus accessories for the MetroSite EDGE Base Station Table 2. Flexbus cable specifications Table 3. LMP accessories for the MetroSite EDGE Base Station Table 4. LMP cable connector specifications Table 5. Abis PCM cable and accessories Table 6. PCM cable 75 Ω specifications Table 7. PCM cable 120 Ω specifications Table 8. Antennas for the Nokia MetroSite EDGE Base Station Table 9. Specifications for the 130o antenna 15 17 20 20 21 22 22 23 25 Table 10.
Solution Accessories Table 28. Contents of the battery connection kit 52 Table 29. Miscellaneous accessories for the Nokia MetroSite EDGE Base Station 53 Table 30. Jumper cable accessories 54 Table 31. Grounding cable specifications 54 Table 32. Specifications for the 230 VAC power cable 55 Table 33. Specifications for the 110 VAC power cable 56 Table 34. Specifications for the DC power cable 56 Table 35.
List of figures Figure 1. Flexbus cable 16 Figure 2. TNC connectors 19 Figure 3. LMP cable and connectors 21 Figure 4. MetroSite 130o panel antenna 25 Figure 5. MetroSite XX-pol 900/1800 MHz panel antenna 27 Figure 6. MetroSite XX-pol 850/1900 MHz panel antenna 29 Figure 7. Omni-directional dual band 900/1800 MHz antenna 31 Figure 8. Omni-directional dual band 850/1900 MHz antenna 33 Figure 9. Indoor omni multi-band antenna 34 Figure 10. Indoor multi-band panel antenna 36 Figure 11.
Solution Accessories 10 (66) © Nokia Corporation Nokia Proprietary and Confidential Draft DN99252966 Issue 3-0 en
Summary of changes Version 1-0, 5th March, 1999. Norman M. Thomas. Version 2-0, 30th August 2001. Tyrone Williams. Version 3-0, August 2002. Kudos (Celia Pires, Mark Seymour). Added chaining extension cables into “Miscellaneous”, made corrections to specifications following comments from Jan Ekman, Tomi Karvonen and Peter Berghall. Version 3-0, October 2002. Kudos (Mark Seymour). Product codes updated. 800/1900 MHz antennas added.
Solution Accessories 12 (66) © Nokia Corporation Nokia Proprietary and Confidential Draft DN99252966 Issue 3-0 en
About this document 1 About this document This document lists the Nokia accessories which are available to support the Nokia MetroSiteTM Base Station. Descriptions and specifications of the accessories are also included. For more information and ordering of the accessories, contact your local Nokia customer services representative.
Solution Accessories 14 (66) © Nokia Corporation Nokia Proprietary and Confidential Draft DN99252966 Issue 3-0 en
Accessories and specifications 2 Accessories and specifications 2.1 Flexbus accessories Table 1. 2.1.1 Flexbus accessories for the MetroSite EDGE Base Station Item Product code Jumper cable, 2.5 m, TNC (m) - TNC (f) CS72450.10 RG223, 4 m, TNC-TNC straight T36625.02 RG223, 8 m, TNC-TNC straight T36625.03 RG223, 15 m, TNC-TNC straight T36625.04 TNC male for flexbus cable straight (RG214) T36630.01 TNC male for flexbus cable 90 degree (RG214) T36631.
Solution Accessories The cable is capable of handling frequencies up to 2.8 GHz and is, for example, used to connect the radio outdoor unit to the transmission unit. Table 2 and Figure 1 identify the diameter of the cable attributes. The 'D' and 'E' min-max ranges allow for the different connectors used. Cables, type RG223, of 4 m, 8 m and 15 m lengths terminated with TNC male straight connectors are available. The product code for each of these is identified in Table 1. Figure 1.
Accessories and specifications Table 2. Parameter Flexbus cable specifications RG214 cable G223 cable Detail Inner Conductor Dielectric Core Outer conductor (layer 1) 2.28 mm diameter 0.9 mm diameter Silver plated copper wires (7) Silver plated copper wire (single) 5.6 Ω/km at 20oC 29.4 Ω/km at 20oC 50+/- 2 Ω impedance 50+/- 2 Ω impedance 101 nf/km capacitance at 800 Hz 106 nf/km capacitance at 800 Hz 201 g/m weight 59 g/m weight Attenuation: 23 dB/100 m at 800 MHz.
Solution Accessories • exceptional cable retention force to withstand vibration and frequent connections and disconnections • long term reliability • usable with RG/U and Raychem Cheminax cables • meets performance requirements of MIL-C-39012 up to 2.8 GHz Only the right-angled connectors are used with type RG214 cable because of the cable's rigidity.
Accessories and specifications Figure 2.
Solution Accessories 2.2 Local Management Port accessories Table 3. 2.2.1 LMP accessories for the MetroSite EDGE Base Station Item Product code Nokia Q1 LMP cable T55270.01 Q1 LMP cable specifications Product code: T55270.01 This is an RS232 cable terminated with a BQ bayonet type connector at one end and a 9-pin `D' type (D9F) connector at the other end. The length of the cable is 2,5 m and is provided already assembled. Table 4.
Accessories and specifications BQ on the BTS end of cable 4 2 D9P (female) on the PC end of cable 3 1 3 LMP out 2 LMP in 4 GND 2 nc = Hole = Pin Figure 3. 2.3 nc RD TD nc GND nc nc nc nc 4 5 9 3 8 2 7 1 6 GND = Ground RD = Received data TD = Transmitted data nc = not connected LMP cable and connectors Abis PCM cable Table 5. DN99252966 Issue 3-0 en 1 2 3 4 5 6 7 8 9 Abis PCM cable and accessories Item Product code Abis PCM cable for MetroSite, 3 m, 120 Ω T36612.
Solution Accessories 2.3.1 PCM cable 75 ohm Product Code: T36602.01 The 75 Ω PCM cable is used for 2 Mbit transmission between the Nokia MetroSite EDGE Base Station and a BSC. This high quality coaxial cable consists of a plain copper inner conductor, polyethylene dielectric material, two copper braids, and a PVC outer jacket. Table 6. 2.3.2 PCM cable 75 Ω specifications Characteristic impedance 75+ / - 4 Ω Mutual capacitance 67 pF/m Wave attenuation 1 MHz 2.
Accessories and specifications Table 7. 2.3.3 PCM cable 120 Ω specifications (Continued) Wave attenuation 20 MHz 7.8 dB/100 m Operating voltage 300 V rms Minimum bending radius 30 mm Diameter 4.1 mm Colour Grey BT43 plug Product code: T36601.01 This connector is used with the TZC5024 cable. For connection of this plug to the Abis 75 Ω coaxial cable, refer to Attachment 1. 2.3.4 TQ plug Product code: CS73214.
Solution Accessories Table 8. Antennas for the Nokia MetroSite EDGE Base Station (Continued) Item Product code MetroSite omni antenna, dual band 870960 / 1710-1880 MHz, 2 dBi, 2 x N female connectors CS72187 MetroSite omni antenna, dual band 824960 / 1805-2170 MHz, 2 dBi, N female CS72187.
Accessories and specifications Figure 4. MetroSite 130o panel antenna Table 9. Specifications for the 130o antenna Item GSM 900 GSM 1800 Frequency range 870-960 MHz 1710-1880 MHz VSWR < 1:1.7 < 1:1.
Solution Accessories Table 9. 2.4.2 Specifications for the 130o antenna (Continued) Item GSM 900 GSM 1800 Isolation > 25 dB (GSM 900 - GSM 900) on Tx band > 30 dB (GSM 1800 - GSM 1800) > 30 dB (GSM 900 - GSM 1800) Input 2 x N female Connector position Bottom Weight 2.
Accessories and specifications 900/1800 MHz XX-pol panel antenna (CS72180) DN99252966 Issue 3-0 en Figure 5. MetroSite XX-pol 900/1800 MHz panel antenna Table 10. Specifications for the MetroSite XX-pol 900/1800 MHz panel antenna Item GSM 900 GSM 1800 Frequency range 870-960 MHz 1710-1880 MHz VSWR < 1.5 < 1.
Solution Accessories Table 10.
Accessories and specifications 850/1900 MHz XX-pol panel antenna (CS72763.01) Figure 6.
Solution Accessories Table 11. Specifications for the MetroSite XX-pol 850/1900 MHz panel antenna Item GSM 850 GSM 1900 Frequency range 824-960 MHz 1710-2170 MHz VSWR < 1.5 < 1.5 Impedance 50 Ω 50 Ω Polarization +45o ; -45o +45o ; -45o Front-to-back ratio (copolar) > 28 dB > 25 dB Half power beam width +45o / -45o +45o / -45o Horizontal: 68 - 65o Horizontal: 65 - 63o Vertical: 16 - 14.5o Vertical: 7.5 - 6.
Accessories and specifications 2.4.3 Omni dual band antenna Product codes: CS72187, CS72187.02 This is a dual port, dual band 900/1800 or 850/1900 MHz antenna. The output is omni-directional (360o) with a gain of 2 dBi and has two units (upper and lower). 900/1800 MHz omni-directional, dual band antenna (CS72187) DN99252966 Issue 3-0 en Figure 7. Omni-directional dual band 900/1800 MHz antenna Table 12.
Solution Accessories Table 12. Specifications for the omni-directional 900/1800 MHz dual band antenna (Continued) Polarization Vertical Isolation > 25 dB Maximum power/input 50 W at 50oC ambient temperature Weight 1.
Accessories and specifications 850/1900 MHz omni-directional, dual band antenna (CS72187.02) DN99252966 Issue 3-0 en Figure 8. Omni-directional dual band 850/1900 MHz antenna Table 13. Specifications for the omni-directional 850/1900 MHz dual band antenna Input 2 x N female Frequency range 824-960 MHz and 1805-2170 MHz for the upper and lower units VSWR < 2.
Solution Accessories Table 13. Specifications for the omni-directional 850/1900 MHz dual band antenna (Continued) Height 216 mm Material Radiator: brass Radome: fibreglass (white) Base: weatherproof aluminium Mounting clamp and screws: stainless steel 2.4.4 Mounting One hole mounting (16 mm) to surfaces of maximum 10 mm thickness or attached laterally at the tip of a tubular mast of 40-70 mm diameter.
Accessories and specifications Table 14. Specifications for the indoor omni multi-band antenna Input N female Frequency range 824-960 MHz and 1425-2170 MHz VSWR < 2.0: 824-960MHz < 2.0: 1425-1710MHz < 1.6: 1710-1990MHz < 2.
Solution Accessories Figure 10. Indoor multi-band panel antenna Table 15. Specifications for the indoor multi-band panel antenna Input Cable RG 223/CU of 1 m length; white; N female connector. Frequency range 824-960 MHz and 1710-2170 MHz VSWR 870-960 MHz and 1710-1900 MHz: < 1.6 824-960 MHz and 1710-2170 MHz: < 2.
Accessories and specifications Installing the multi-band indoor panel antenna 1. Fix the attachment plate to the wall using two 4 mm diameter screws. See [1] in Figure 11. 2. Align the antenna over the attachment plate, keeping the cable in the middle of the plate. See [2] in Figure 11. 3. Pull the antenna downwards until it clicks into place. See [3] in Figure 11. Do not pull the antenna downwards with the antenna cable. Figure 11. 2.4.
Solution Accessories Figure 12. 2.5 Antenna pole mounting clamp GSM/EDGE 900, 1800 and 1900 combiners Table 16. Combiners for the Nokia MetroSite EDGE Base Station Item Product code GSM/EDGE 900 BTS 2-to-1 combiner CS72216.01 GSM/EDGE 1800 BTS 2-to-1 combiner CS72216.02 GSM/EDGE 1900 BTS 2-to-1 combiner CS72216.03 Product code: CS72216.01; CS72216.02; CS72216.03 The GSM/EDGE combiner is a cost-effective solution for combining two MetroSite TRXs into a single antenna and feeder system.
Accessories and specifications The GSM/EDGE combiner allows you to combine the transmit signals from the transceivers and also divide receive signals from the antenna to those transceivers. The GSM/EDGE 900, 1800 and 1900 combiners function in an identical manner and are designed for mounting outdoors. The combiners are compact, lightweight, easy to install, and require no maintenance. Figure 13.
Solution Accessories Figure 14. Dimensions of the GSM/EDGE combiner Table 17. Specifications for the GSM/EDGE combiners GSM 900 Combiner GSM 1800 Combiner GSM 1900 Combiner Frequency range 925-960 MHz 1805-1880 MHz 1930-1990 MHz Impedance 50 Ω 50 Ω 50 Ω Insertion loss 3.5 dB maximum 3.5 dB maximum 3.
Accessories and specifications Table 17. Specifications for the GSM/EDGE combiners (Continued) GSM 900 Combiner GSM 1800 Combiner GSM 1900 Combiner Frequency range 880-915 MHz 1710-1785 1850-1910 Impedance 50 Ω 50 Ω 50 Ω Insertion loss 3.5 dB maximum 3.5 dB maximum 3.5 dB maximum Antenna port return loss 18 dB minimum 18 dB minimum 18 dB minimum BTS port return loss 18 dB maximum 18 dB maximum 18 dB maximum Power division imbalance 0.5 dB maximum 0.5 dB maximum 0.
Solution Accessories Table 17. 2.6 GSM 900 Combiner GSM 1800 Combiner GSM 1900 Combiner Storage Class 1.3E ETSI 300 010-1-1 Class 1.3E ETSI 300 010-1-1 Class 1.3E ETSI 300 010-1-1 Transportation Class 2.3 ETSI 300 019-1-2 Class 2.3 ETSI 300 019-1-2 Class 2.3 ETSI 300 019-1-2 MTBF > 500,000 hours > 500,000 hours > 500,000 hours Antenna lines Table 18. 2.6.
Accessories and specifications Figure 15. Antenna line cable Table 19. Sheath characteristics for the antenna line cable Sheath Characteristics Item 3/8"-50 LD GY7047 (CS72259.10) 3/8"-50 (CS72258.10) Jacket Telegrey, LD polyethylene Black, LD polyethylene IEC754-1/-2 (halogen free, noncorrosive Yes Yes IEC1034 (low smoke emission) No No IEC332-3C (fire retardant) No No UV retardant Yes Yes Minimum installation temperature -20o C -20o C Table 20.
Solution Accessories Table 20. Cable characteristics for the antenna line cable (Continued) Cable Characteristics Item CS72258.10 and CS72259.10 (3/8") Electrical at +20o C Characteristic impedance 50 + 1 Ω Attenuation See table Velocity factor 0.81 Capacitance 82 pF/m Cut-off frequency 15200 MHz Maximum operating frequency 3000 MHz Maximum power rating See table Peak RF voltage rating 1.04 kV Peak power rating 11 kW DC resistance: inner conductor 5.
Accessories and specifications Table 21. Attenuation and power characteristics for the antenna line cable Attenuation (maximum) and power rating CS72258.10 and CS72259.10 (3/8”) Frequency (MHz) 2.6.2 Attenuatio n at ambient Power rating at ambient Power rating at ambient temp. 20o C dB/100 m temp.40o C inner conductor temp.40o C inner conducto +70o C (kW) r +100o C (kW) 1000 14.7 0.26 0.57 1200 16.3 0.24 0.51 1400 17.8 0.22 0.47 1600 19.1 0.20 0.44 1800 20.5 0.19 0.
Solution Accessories Table 22. Specifications for the N male connector Item CS72683.20 (3/8") Frequency f/GHz 0
Accessories and specifications Figure 17. N male connector, right angled Table 23. Specifications for the N male connector, right angled Item CS72683.21 (3/8") Frequency f/GHz 0< f ≤1 1 < f ≤2 2 < f ≤ 2.7 2.7 < f ≤ 3.7 VSWR ≤ 1.02 ≤ 1.04 ≤ 1.06 ≤ 1.
Solution Accessories Table 23. 2.6.4 Specifications for the N male connector, right angled (Continued) Item CS72683.21 (3/8") a (mm) 36 b (mm) 38.3 c (mm) 23 7-16 Straight Male connector Product code: CS72697 (3/8") This connector type is suitable for 3/8" helical cable and facilitates solderless attachment of the inner wire of the connected cable. Figure 18. 7-16 Straight male connector Table 24.
Accessories and specifications Table 24. 2.7 Specifications for the N male connector, right angled (Continued) Item CS72697 (3/8") Assembly time < 2 minutes Weight 105 g a (mm) 39 b (mm) 21 MetroSite Battery Backup Unit Product code: CS70401.01 for BBU (without batteries) and .02 for batteries 2.7.1 Battery Backup Unit The MetroSite BBU is designed to provide 110 VAC or 230 VAC backup support for connected elements.
Solution Accessories One end of the cable is fitted with an IEC320 female connector and the other end with an appropriate three-pin male connector for connection to the mains power source (user defined). Note The MetroSite BTS or MetroHub mains power cable can be utilised for connecting the MetroSite BBU to the mains power source. Table 25. 2.7.3 Specifications for the 230 VAC mains power cable Code Detail Cross section 1.5 mm2 Nominal diameter 9.
Accessories and specifications One end of the cable is fitted with an IEC320 female connector and the other end with an IEC320 male connector. The former connects to the MetroSite BBU and the latter to a MetroSite BTS or MetroHub. Table 26. 2.7.4 Specifications for the 230/110 VAC mains power cable Code Detail Cross section 1.5 mm2 Nominal diameter 9.
Solution Accessories Table 27. 2.7.5 Specifications for the alarm cable Pin Signal Pin Signal 1 EAC1 14 GND 2 EAC2 15 GND 3 EAC3 16 GND 4 EAC4 17 GND 5 EAC5 18 GND 6 EAC6 19 GND 7 EAC7 20 GND 8 EAC8 21 GND 9 EAC9 22 GND 10 EAC10 23 GND 11 CO1 24 CO3 12 +3 V 25 CO4 13 CO2 26 +5 V Battery connection kit Note This item is included in CS70401.01.
Accessories and specifications Figure 19. 2.8 Miscellaneous Table 29. DN99252966 Issue 3-0 en Battery connection kit Miscellaneous accessories for the Nokia MetroSite EDGE Base Station Item Product code Earthing cable, 16 mm2 CS73174 Metro Hopper optical alignment tool T55875.01 Alarm cable (between BTS and Hub) CS72451.20 Pole mounting kit for MetroSite cabinet CS72451.10 Power cable for BTS/Hub (230 VAC) CS72452.50 Power cable for BTS/Hub (110 VAC) CS72452.
Solution Accessories Table 29. 2.8.1 Item Product code Extension cable kit, 1 metre 469584A Extension cable kit, 3 metres 467614A Extension cable kit, 5 metres 469585A Extension adapter for PCM/clock cable CS74814 Jumper cables Table 30. 2.8.2 Miscellaneous accessories for the Nokia MetroSite EDGE Base Station (Continued) Jumper cable accessories Code Description CS72672 Jumper cable 2,5 m, 3/8” N-m angle/N-m telegrey CS72680.
Accessories and specifications Table 31. 2.8.3 Grounding cable specifications (Continued) Code Details Minimum recommended handling temperature -50o C Minimum recommended bending radius (single bend) 22 mm Colour Yellow-green AC power cables for MetroSite BTS or MetroHub The power cables for AC connectivity are light and flexible. They can be installed in dry, damp and wet environments, both indoor and outdoor, in addition to firesensitive locations.
Solution Accessories 110 VAC power cable: CS72452.51 Table 33. 2.8.4 Specifications for the 110 VAC power cable Code Detail Cross section 1.5 mm2 Nominal diameter 9.
Accessories and specifications Table 34. 2.8.5 Specifications for the DC power cable (Continued) Code Detail Live wire colour Brown Neutral wire colour Blue Earthing cable colour Green-yellow Sheath colour Black Optical Alignment Tool Product code: T55875.01 The optical alignment tool is used to align the MetroHopper for optimum efficiency. The optical alignment tool is fitted on the MetroHopper mounting assembly before the MetroHopper is fitted.
Solution Accessories Table 35. Specifications for the optical alignment tool Item Details Type Optical red dot alignment sight. ‘Aimpoint Comp’ sight with a 90oviewing angle and a mounting base perpendicular to the optical axis of sight. Manufacturer Aimpoint AB, Sweden Application Used with MetroSite Alignment Unit, type T55850.01 Alignment ranges Alignment range with 2x magnification lens, 0.5 to 1 km.
Attachments 3 Attachments Attachment 1: Installation instructions for the Abis 75-ohm interface of Nokia MetroSite with TZC75024 cable For installation the following listed tools are needed: • CS74863 Peeling Tool • CS74862 Centre Contact Crimp Tool • CS77550.01 Crimp Tool The connector consists of three parts: a ferrule, a jack and a body.
Solution Accessories Instructions: 60 (66) 1. Slide the shrinking sleeve and the ferrule onto the un-peeled part of the cable. 2. Peel the cable as shown in the picture. The lengths of the peeled parts are: 21 mm (0.827"), 13 mm (0.512") and 4.5 mm (0.177"). 3. Position the jack on the end of the cable. Push the cable into the crimping tool so that the jack is inside the crimping hole, and crimp the jack onto the conductor. 4.
Attachments 6. Crimp the ferrule onto the body with the crimping tool CS77550.01. Use the gap '4.52' on the tool. 7. Draw the shrinking sleeve over the ferrule and warm it to cause it to shrink onto the ferrule. Attachment 2: Installation configuration for the Abis 120-ohm interface of Nokia MetroSite. Note This cable is provided already assembled but is shown here to identify all the parts constituting an Abis 120-ohm interface. A TQ connector is fitted to both ends of the cable.
Solution Accessories Attachment 3: Installation instructions for the AC power plug for Nokia MetroSite. The power feeder is a flexible rubber insulated cable with three multi-wire conductors having dimensions of: 1.5 mm2 or 2.5 mm2 (AWG 15.5-13.5).
Attachments Instructions: DN99252966 Issue 3-0 en 1. Strip the power feeder cable from its main insulation 20 mm (0.787"). 2. Strip the inner conductors and cut them so that the blue and brown wires are 20 mm (0.787") long and the yellow/green wire is slightly longer, at 25 mm (1"). The stripped area is 4 mm (0.157") long. 3. Undo the screw holding the body parts together and store the screw, nut and washer in a safe place. Separate the two parts of the body. 4.
Solution Accessories 6. Undo each plug connector screw sufficiently to enable the cable wire to be inserted and insert the wires in each connector. Note The brown (live) wire to be inserted in the right-hand connector as viewed from the front. The blue (neutral) wire is inserted into the left-hand connector, and the yellow/green (earth) wire to the centre connector. 7. Tighten each screw in turn to fix the wires in the connectors. 8.
Attachments Instructions: DN99252966 Issue 3-0 en 1. Strip the power feeder cable from its main insulation 'X' mm (TBA). 2. Strip the inner conductors and cut them so that they are of equal length. 3. Strip each wire insulation to 'Y' mm (TBA) length using a sharp blade, taking care not to cut any strands of wire. 4. Insert each wire, in turn, into a contact and using the crimping tool, crimp the contact around the wire. 5. Undo the cable clamp to enable the cable to be inserted. 6.
Solution Accessories 66 (66) © Nokia Corporation Nokia Proprietary and Confidential Draft DN99252966 Issue 3-0 en
