User's Manual

ManualsBrandsNokia Solutions and Networks ManualsElectronics2.5 GHz Diversity Access Point

Access P oint Hardw are Installation Customer Dened Input/Output Cables

Output Pins T able 3 -13 lists the pinouts for the Customer Deﬁned Output connectors 1 -2

and 3 -4.

Table 3 -13 Customer Dened Output Connector Pins 1–2 and 3–4

Pin Number Description Pin Number Description

Connector 1–2 Connector 3–4

Customer Deﬁned Output 1 NC

Customer Deﬁned Output 3 NC

Customer Deﬁned Output 1 C

Customer Deﬁned Output 3 C

Customer Deﬁned Output 1 NO

Customer Deﬁned Output 3 NO

Customer Deﬁned Output 2 NC

Customer Deﬁned Output 4 NC

Customer Deﬁned Output 2 C

Customer Deﬁned Output 4 C

Customer Deﬁned Output 2 NO

Customer Deﬁned Output 4 NO

68P09277A59 -8 3 -19

MA Y 2007 PRELIMINARY - UNDER DEVELOPMENT

Summary of content (11 pages)

PAGE 1
Access Point Hardware Installation Customer Dened Input/Output Cables Output Pins Table 3-13 lists the pinouts for the Customer Deﬁned Output connectors 1-2 and 3-4.
PAGE 2
Customer Dened Input/Output Cables Chapter 3: Cable Descriptions 3-20 68P09277A59-8 PRELIMINARY - UNDER DEVELOPMENT MAY 2007
PAGE 3
Chapter 4 Access Point Hardware Installation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09277A59-8 MAY 2007 4-1 PRELIMINARY - UNDER DEVELOPMENT
PAGE 4
Installation Overview Chapter 4: Access Point Hardware Installation Installation Overview ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Overview This chapter provides procedures for Base Control Unit (BCU) and RF Head installation and associated cabling. The following items are covered in this chapter.
PAGE 5
Access Point Hardware Installation Installation Overview RF Head Installation The process of installing the RF Head requires that the following procedures be completed in the order shown: 1. Attach the Pole Mounting Bracket Assembly to pole 2. Install RF Head (with side mounting brackets attached) 3. Connect Earth Ground cable between RF Head and tower 4. Connect DC power cables from RF Head to BCU 5.
PAGE 6
Connector Locations Chapter 4: Access Point Hardware Installation Connector Locations ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Base Control Unit Connector Locations Figure 4-1 shows the location of the cable connectors on the BCU. RF Head Connector Locations Refer to Figure 1-4 for the location of the cable connectors on the RF Head.
PAGE 7
Access Point Hardware Installation Base Control Unit Installation Base Control Unit Installation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Overview This section contains procedures for installing a Base Control Unit (BCU). Refer to Figure 1-1 for an overall view of the BCU.
PAGE 8
Base Control Unit Installation Figure 4-1 Chapter 4: Access Point Hardware Installation BCU Card Cage Compartment Fan PSU 2 PSU 1 PSU 3 Circuit Breakers Alarm Card Modem Cards Controller Cards Heater (Outdoor Unit Only) 4-6 ti-cdma-04167.
PAGE 9
Access Point Hardware Installation Base Control Unit Installation Figure 4-2 BCU Power and Customer Interface Compartment RF -GPS Module Customer Input / Output connectors AC Power compartment with cover removed RGPS connector behind cover Ethernet connections ti-cdma-04174.eps Electrical The BCU is designed to use 100–240 VAC, +27 VDC, or –48 VDC. If powered by single phase AC voltage (customer supplied), the range is 100/240 VAC @ 50/60 Hz, 16A max., +20 to +30 VDC, 78A max.
PAGE 10
Base Control Unit Installation Chapter 4: Access Point Hardware Installation Battery Backup Battery backup or associated charging/control circuitry for the AC version of the BCU is not supported. Dimension and Weight If the BCU must be physically adjusted/moved, Motorola recommends that a minimum of two people perform this function. • Dimension: 508 mm (20 in.) D x 482.6 mm (19 in.) W x 810.8 mm (32 in.
PAGE 11
Access Point Hardware Installation Figure 4-3 Base Control Unit Installation Air Flow Clearances Top: 101.6 mm (4 in.) Rear: 76.2 mm (3 in.) Left: 101.6 mm (4 in.) Right: 101.6 mm (4 in.) Front: 152.4 mm (6 in.) ti-cdma-05733.eps For proper door opening, the BCU requires the following minimum clearances: • DACS Door — 431.8 mm (17 in.) • Customer Interface Door — 406.4 mm (16 in.) • Card Cage Door — 406.4 mm (16 in.