APPLICANT: MOTOROLA Cellular Networks FCC ID: IHET7HM1 Users Manual Exhibit 2.5GHz MOTOwi4™ 25600 Diversity Access Point FCC Filing – WAP25600 MOTOwi4TM Diversity Access Point @ 2.
Ground Based Access Point (GAP) Hardware Installation 68P09286A73-1 JUL 2007 PRELIMINARY - UNDER DEVELOPMENT © 2006 Motorola, Inc.
Accuracy While reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. Motorola, Inc.
Table of Contents Contents ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Ground Based Access Point (GAP) Hardware Installation Revision history . . . . . . . . . . . . . . . . . . Version information . . . . . . . . . . . . . . Resolution of Service Requests . . . . . . . . Incorporation of Change Notices. . . . . . . . General information . . . . . . . . .
Contents Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 1-7 1-7 Chapter 2: Site Preparation General . . . . . . . . . . . . . . . . . . . . . . . Overview. . . . . . . . . . . . . . . . . . . . . Indoor and outdoor sites . . . . . . . . . . . . .
Ground Based Access Point (GAP) Hardware Installation Contents Cage to cage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External cabling to rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 4-9 Chapter 5: Outdoor GAP Hardware Installation Outdoor (cabinet - mount) GAP installation . . . . . . GAP cabinets. . . . . . . . . . . . . . . . . . . . Outdoor GAP product identification and configurations Common outdoor mounting information . . . .
Contents Chapter 8: XXXXXXXXXXXX Chapter 9: XXXXXXXXXXXX Chapter 10: XXXXXXXXXXXX Chapter 11: XXXXXXXXXXXX Appendix A: Alternate RF Head Installation Procedure Appendix B: Alternate RGPS Installation Appendix C: MMI Cable Fabrication iv 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
List of Figures List of Figures ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure 2-1: GAP cabinet - lifting and mounting bracket locations . . . . 4-1: Concrete mounting . . . . . . . . . . . . . . . . . . . . . 4-2: Wooden floor mounting . . . . . . . . . . . . .
List of Figures vi 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
List of Tables List of Tables ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Table Table Table Table Table Table Table 1-1: 1-2: 3-1: 3-2: 5-1: 7-1: 7-2: Abbreviations and Acronyms Tools and Materials . . . . . Cable Length Requirements Cable Lengths. . . . . . . . General materials needed . . Site information. . . . . . . Checklist . . . . . . . . . . .
List of Tables viii 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
About This Manual Ground Based Access Point (GAP) Hardware Installation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ What is covered in this manual? This manual describes general information and procedures for unpacking, site preparation, installation, and site clean up of the Ground Based Access Point (GAP) hardware.
Revision history Revision history ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Version information The following shows the status of this document since it was first released.
General information General information ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Purpose Motorola cellular communications documents are intended to instruct and assist personnel in the operation, installation and maintenance of the Motorola cellular infrastructure equipment and ancillary devices.
General information Text conventions The following conventions are used in the Motorola cellular infrastructure documents to represent keyboard input text, screen output text, and special key sequences. Input Characters typed in at the keyboard are shown like this. Items of interest within a command appear like this. Output Messages, prompts, file listings, directories, utilities, and environmental variables that appear on the screen are shown like this.
Contacting Motorola Contacting Motorola ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Motorola appreciates feedback from the users of our documents. 24–hour support If you have problems regarding the operation of your equipment, contact the Customer Network Resolution Center (CNRC) for immediate assistance.
Security advice Security advice ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Motorola systems and equipment provide security parameters that can be configured by the operator based on their particular operating environment. Motorola recommends setting and using these parameters following industry recognized security practices.
Warnings, cautions, and notes Warnings, cautions, and notes ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The following describes how warnings and cautions are used in this document and in all documents of this Motorola document set. Warnings Warnings precede instructions that contain potentially hazardous situations.
Safety Safety ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ General safety The following general safety guidelines apply to Motorola equipment: • The power jack and mating plug of the power cable must meet International Electrotechnical Commission (IEC) safety standards. Refer to Grounding Guideline for Cellular Radio Installations – 68P81150E62.
Caring for the environment Caring for the environment ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The following information describes national or regional requirements for the disposal of Motorola supplied equipment and for the approved disposal of surplus packaging. Contact the Customer Network Resolution Center (CNRC) for assistance.
CMM labeling and disclosure table CMM labeling and disclosure table ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The People’s Republic of China require that our products comply with China Management Methods (CMM) environmental regulations.
Motorola document set Motorola document set ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The Motorola document sets provide the information to operate, install, and maintain the Motorola equipment.
Supplemental information Supplemental information ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Third party computer software and trademarks Computer software The following is a list of the 3rd party computer software copyrights contained within this Motorola product. Company Copyright Apache Software Foundation* Copyright 2002-2007 All rights reserved.
FCC requirements FCC requirements ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Content This section presents Federal Communications Commission (FCC) Rules Parts 15 and 68 requirements and compliance information for the (WAP25400) MOTOwi4™ Diversity Access Point .
FCC requirements Part 15.21 - Information to user Changes or modifications that change the FCC type approved configuration of the equipment could void the user’s authority to operate the equipment. 15.105(b) - Information to user This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC requirements DAP label and location A label similar to the one illustrated is located as shown. All symbols may not display on the label depending on the market. ti_cdma_wimaxdap.eps BCU label A label similar to the one illustrated is located on the equipment. All symbols may not display on the label depending on the market.
FCC requirements 16 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 1 Overview ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09286A73-1 JUL 2007 1-1 PRELIMINARY - UNDER DEVELOPMENT
Introduction Chapter 1: Overview Introduction ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This document provides information pertaining to the hardware and cabling installation for the outdoor and indoor (19 – inch rack) version of the Motorola Ground Based Access Point (GAP) Hardware.
Ground Based Access Point (GAP) Hardware Installation Product Description Product Description ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The Motorola Ground – based Access Point (GAP) hardware is made up of three main component assemblies; the Base Transceiver (sub) System (BTS) and the Battery Backup Unit (BBU).
Manual Order Chapter 1: Overview Manual Order ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section outlines the content of this manual.. The appendices provide additional information about installation not otherwise covered in the chapters. Chapter 1 – Overview This is a brief outline of the manual.
Ground Based Access Point (GAP) Hardware Installation Recommended Documents Recommended Documents ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The following documents may be required to assist in the installation of the GAP Hardware.
Abbreviations and Acronyms Chapter 1: Overview Abbreviations and Acronyms ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Table 1-1 lists the uncommon abbreviations and acronyms that appear within this manual.
Ground Based Access Point (GAP) Hardware Installation Tools and Materials Tools and Materials ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Introduction Many of the tools and materials depend on the GAP installation, being indoor or outdoor. The indoor GAP is mounted in a standard 19 - inch rack. The outdoor GAP is installed on a concrete slab.
Tools and Materials Table 1-2 Chapter 1: Overview Tools and Materials (Continued) Hand Tool Materials Purpose Electrical Tape Customer Supplied General purpose Adjustable Crescent Wrench Customer Supplied General purpose Torx Screw Driver Set (T30 and lower) Customer Supplied General purpose Tie-Wraps Customer Supplied General purpose, varying lengths.
Chapter 2 Site Preparation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This chapter provides general information for verification of the site prior to installation of the GAP hardware.
General Chapter 2: Site Preparation General ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ All customer sites have unique situations for installation of equipment. Specific site situations that affect installation need to be identified, and resolved if necessary, prior to the actual installation of any equipment.
Ground Based Access Point (GAP) Hardware Installation Site Preparation Overview Site Preparation Overview ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section provides the procedures and information to verify that the site is ready for equipment installation.
Initial site inspection Chapter 2: Site Preparation Initial site inspection ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section describes general items to consider for an initial site inspection.
Ground Based Access Point (GAP) Hardware Installation Initial site inspection • General safety inspection to ensure a safe working environment for personnel and protection of equipment. • Lighting and power for installation and maintenance personnel. • Configuration of the GAP cabinets, either side - by - side or stacked. • Appropriate general space to install the GAP cabinets. • Availability of appropriate electrical ground connections for the GAP equipment.
Prepare Site for Equipment Arrival Chapter 2: Site Preparation Prepare Site for Equipment Arrival ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section covers various topics not all of which are needed at every site. Based on the site characteristics, execute the steps that apply to your site.
Ground Based Access Point (GAP) Hardware Installation Prepare Site for Equipment Arrival Procedure 2-1 Procedure to prepare the site for the GAP equipment (Continued) 4 • There is clear access to move the equipment to the desired mounting area • There is sufficient space for installation and service access to the equipment • Customer supplied shelters (if needed) are installed Note any concerns or conditions that may create a safety hazard to personnel, or impair the installtion of the GAP equipmen
Site layout inspection Chapter 2: Site Preparation Site layout inspection ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Most of the site layout should have been inspected in the previous sections, and any special conditions noted. Consult with the site manager to resolve any outstanding condition that would impair the installation or safety of personnel.
Ground Based Access Point (GAP) Hardware Installation Shipping and Handling Shipping and Handling ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Overview The purpose of this section is to describe how the GAP Base Transceiver (sub) System (BTS) (includes the BCU and TRX), Battery Backup Unit (BBU) and RF Head are packaged for shipping and how to correctly unpack
Shipping and Handling Chapter 2: Site Preparation • The BTS cabinet is shipped with the BCU cage with all cards/modules and internal cabling installed. • The BBU cabinet is shipped with all batteries and internal cabling installed. • Depending on the ordered configuration, the TRX cage can be in either the BTS cabinet and / or the BBU cabinet. • The TRX cage, with the installed TRX modules, will have all internal cabling installed.
Ground Based Access Point (GAP) Hardware Installation Unpacking Unpacking ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section describes unpacking the various units for the GAP. GAP equipment The GAP equipment is shipped either as and indoor unit and as an outdoor unit.
Unpacking Chapter 2: Site Preparation Figure 2-1 GAP cabinet - lifting and mounting bracket locations PRELIMINARY ILLUSTRATION Unpacking procedure Procedure 2-2 1 2 3 4 5 2-12 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Ground Based Access Point (GAP) Hardware Installation Unpacking Indoor GAP The indoor BCU and TRX cages are internally cabled and installation mainly consists of mounting the cages in the indoor rack, grounding cabling, main power cabling, cabling between the cages, and cabling between the TRX modules and the RF antenna(s).
Unpacking Chapter 2: Site Preparation 2-14 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 3 Cable Descriptions ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Individual installations at customer sites vary. This chapter describes the typical cabling for the GAP.
Overview Chapter 3: Cable Descriptions Overview ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This chapter provides the descriptions of the site cabling. Procedures for routing cables (through metallic or conductive conduit) to the outdoor equipment are found in Chapter 4 Indoor GAP Hardware Installation .
Ground Based Access Point (GAP) Hardware Installation Congurations Supported Congurations Supported ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This chapter supports cable installation for 3 and 4 sector configurations.
Cable Installation Order Chapter 3: Cable Descriptions Cable Installation Order ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1. Ground Cabling 2. Power Cabling 3. Antenna Cabling 4. RGPS or Local GPS Cabling 5. Ethernet Cabling 6. Fiber Optic Cabling 7.
Ground Based Access Point (GAP) Hardware Installation Cable Descriptions and Part Numbers Cable Descriptions and Part Numbers ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Table 3-1 gives the cable descriptions and part numbers of the various cables that connect the GAP Base Control Unit (BCU), the GAP Battery Backup Unit (BBU), the GPS antenna, and the RF head.
Cable Descriptions and Part Numbers Chapter 3: Cable Descriptions Table 3-1 Cable Length Requirements (Continued) Cable Qty Part Number Description 3089843T03 Fiber Optic Cable, 60 m (196.8 ft) 3089843T04 Fiber Optic Cable, 80 m (262.4 ft) 3089843T05 Fiber Optic Cable, 100 m (328.0 ft) J 6 Customer Supplied Ethernet cables, RJ-45 connectors, straight K 1 GCNTM20A3A CGDSVXL550 FSJ4–50B) Assembly, Receiver, GPS, RF Module Antenna, GPS, with mounting and 50 ft. cable.
Ground Based Access Point (GAP) Hardware Installation Cable Lengths Cable Lengths ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Table 3-2 gives the typical lenghts of the various cabling. Table 3-2 Cable Lengths From To Cable Cable Length BCU DC Source RF Head DC Connector G 5 lengths, 20 to 100 m in 20 m increments (65.
Cable Lengths Chapter 3: Cable Descriptions 3-8 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 4 Indoor GAP Hardware Installation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This chapter describes guidelines for installing the GAP hardware in an indoor rack.
Indoor (rack - mount) GAP installation Chapter 4: Indoor GAP Hardware Installation Indoor (rack - mount) GAP installation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section provides information to install the Ground - based Access Point (GAP) in an indoor environment. This requires the use of a standard 19 - inch rack.
Ground Based Access Point (GAP) Hardware Installation Indoor GAP product identication Indoor GAP product identication ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ his section shows the various configuration for indoor GAP cabinets.
Rack mounting conguration Chapter 4: Indoor GAP Hardware Installation Rack mounting conguration ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section shows the typical mounting configuration of the GAP cages in a standard 19 inch rack.
Ground Based Access Point (GAP) Hardware Installation Mounting and bolt congurations Mounting and bolt congurations ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section describes different mounting bolt configurations and isolation considerations for both indoor and outdoor GAP installations.
Mounting and bolt congurations Chapter 4: Indoor GAP Hardware Installation Installation on concrete Concrete mounting is used in an outdoor GAP configuration. The same mounting can be used for an indoor rack mounting on a concrete floor. Due to the weight of the GAP cabinet, the supporting structure (concrete slab) must be able to withstand at least 1000 lbs (500 kg). Refer to Figure 4-1 for a typical cross - section of the concrete bolt mounting to the GAP cabinet or rack mounting brackets.
Ground Based Access Point (GAP) Hardware Installation Mounting and bolt congurations Due to the weight of the GAP components and rack, the supporting structure (oor deck) must be able to withstand at least 1000 lbs (500 kg). A structural oor support, such as an iron I-beam, underneath the wooden oor is recommended. Refer to Figure 4-2 for a typical cross - section of the wooden floor bolt mounting to the GAP cabinet or rack mounting brackets.
Installation of GAP cages in the indoor rack Chapter 4: Indoor GAP Hardware Installation Installation of GAP cages in the indoor rack ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ BCU cage TRX cage 4-8 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Ground Based Access Point (GAP) Hardware Installation Rack cabling with cages installed Rack cabling with cages installed ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Cage to cage External cabling to rack 68P09286A73-1 JUL 2007 4-9 PRELIMINARY - UNDER DEVELOPMENT
Rack cabling with cages installed Chapter 4: Indoor GAP Hardware Installation 4-10 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 5 Outdoor GAP Hardware Installation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This chapter describes guidelines for installing the GAP hardware cabinets in an outdoor environment.
Outdoor (cabinet - mount) GAP installation Chapter 5: Outdoor GAP Hardware Installation Outdoor (cabinet - mount) GAP installation ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section provides general information to install the Ground - based Access Point (GAP) in an outdoor environment. Each customer installation will vary.
Ground Based Access Point (GAP) Hardware Installation Outdoor GAP product identication and congurations Outdoor GAP product identication and congurations ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The following sections outline general mounting configurations for the GAP product.
GAP concrete slab mounting Chapter 5: Outdoor GAP Hardware Installation GAP concrete slab mounting ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section shows the typical mounting used on a concrete slab for the outdoor GAP cabinet(s). This section also applies to mounting the cabinets on a concrete floor as well.
Ground Based Access Point (GAP) Hardware Installation Figure 5-1 GAP concrete slab mounting Single cabinet mounting PRELIMINARY ILLUSTRATION 68P09286A73-1 5-5 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
GAP concrete slab mounting Figure 5-2 Chapter 5: Outdoor GAP Hardware Installation Dual cabinet mounting PRELIMINARY ILLUSTRATION Cabinet mounting Depending on how the external power and interconnections are run to the cabinets, this will determine if the GAP cabinets are mounted on a support between the concrete slab and the cabinet(s). Routing of the external power and interconnections between the cabinets is through the cabinet rear or underside of the cabinet.
Ground Based Access Point (GAP) Hardware Installation GAP concrete slab mounting Figure 5-3 GAP BTS cabinet “mud room” PRELIMINARY ILLUSTRATION Conduit routed through back of BTS cabinet Figure 5-4 shows the conduit routed through the back of the BTS cabinet. This will not require a support between the cainet and the conrete slab. The cabinet may be mounted directly to the concrete slab.
GAP concrete slab mounting Chapter 5: Outdoor GAP Hardware Installation Figure 5-4 “Mud room” conduit routed through back of BTS cabinet PRELIMINARY ILLUSTRATION Conduit routed through bottom of BTS cabinet Figure 5-5 shows the conduit routed through the bottom of the BTS cabinet. This will require a support between the cainet and the conrete slab.
Ground Based Access Point (GAP) Hardware Installation GAP concrete slab mounting Figure 5-5 “Mud room” conduit routed through bottom of BTS cabinet PRELIMINARY ILLUSTRATION I-beam support To elevate the GAP cabinet from the concrete mounting, an I-beam support can be used. Three I-beams are required for even support of the GAP cabinet. This description uses a 12 - inch I-beam to allow clearance for a 90 - degree flexible conduit bend.
GAP concrete slab mounting Figure 5-6 Chapter 5: Outdoor GAP Hardware Installation I-beam support for a single GAP cabinet PRELIMINARY ILLUSTRATION Figure 5-7 I-beam support for two GAP cabinets PRELIMINARY ILLUSTRATION 5-10 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Ground Based Access Point (GAP) Hardware Installation Outdoor mounting and bolt congurations Outdoor mounting and bolt congurations ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The mounting of a GAP cabinet to an outdoor concrete slab is similar to mounting an indoor GAP frame to a concrete floor. The same techniques are used.
Concrete pad installation and ground system Chapter 5: Outdoor GAP Hardware Installation Concrete pad installation and ground system ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Materials needed Also see the tools list in the beginning of this manual.
Ground Based Access Point (GAP) Hardware Installation Concrete pad installation and ground system Figure 5-8 Ground ring layout GROUNDING RING #3 BSWG (#2 AWG;35 mm2) SOLID COPPER W/TIN COATING GROUND TO CABINET (1 PER CABINET) #3 BSWG (#2 AWG;35 mm2) SOLID COPPER W/TIN COATING 2438 mm (96IN.) GROUND RODS (8−12) 609 mm (2’ 0IN.) GROUND TO REBAR (CADWELD) REBAR JOINTS (CADWELD) (4) GROUND TO ANTENNA #3 BSWG (#2 AWG; 35 mm2) SOLID COPPER W/TIN COATING FRONT REBAR 10 mm (3/8IN.) MINIMUM.
GAP side - by - side conguration Chapter 5: Outdoor GAP Hardware Installation GAP side - by - side conguration ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section shows a typical installation of the GAP side - by - side cabinet configuration.
Ground Based Access Point (GAP) Hardware Installation GAP stacked conguration GAP stacked conguration ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Stacked cabinets Figure 5-11 GAP cabinets PRELIMINARY ILLUSTRATION 68P09286A73-1 5-15 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
GAP Cabinet cabling Chapter 5: Outdoor GAP Hardware Installation GAP Cabinet cabling ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Grounding Cabling between cabinets External cabling to cabinets Other cabling 5-16 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 6 Optional Equipment ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09286A73-1 JUL 2007 6-1 PRELIMINARY - UNDER DEVELOPMENT
GAP Cabinet cabling Chapter 6: Optional Equipment 6-2 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 7 What’s Next and Cleanup ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09286A73-1 JUL 2007 7-1 PRELIMINARY - UNDER DEVELOPMENT
Introduction Chapter 7: What’s Next and Cleanup Introduction ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section describes general information regarding the final steps of the installation.
Ground Based Access Point (GAP) Hardware Installation Site Cleanup Site Cleanup ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Tools and storage Place all hand and power tools in the installation tool kit or other appropriate place. Note any tools that need replacement, cleaning, or adjustment.
Site Cleanup Chapter 7: What’s Next and Cleanup • Check for any safety hazards and correct if necessary as specified by the site manager.
Ground Based Access Point (GAP) Hardware Installation Installation checklist Installation checklist ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This section provides a general list of items to be checked upon the completion of the site installation.
Installation checklist Chapter 7: What’s Next and Cleanup Table 7-2 Checklist Item no. Item 1 Equipment is not damaged. 2 Air flow clearance requirements are met. Notes Door opening clearance requirements are met. 3 If indoor installation; GAP rack is securely mounted to floor. If outdoor installation; GAP cabinet(s) is securely mounted to floor or concrete slab. If outdoor installation; GAP cabinet(s) that are stacked are securely mounted together.
Ground Based Access Point (GAP) Hardware Installation Installation checklist Table 7-2 Checklist (Continued) Item no. Item 13 RF Head is grounded. 14 RGPS is cabled to BCU. 15 RGPS head and mast are secure. 16 RGPS connection is protected by lightning arrestors (if applicable). 17 RGPS head has a clear view of the sky and is not in a location which accumulates debris. Make sure the RGPS is located away from the transmit antennas. 18 Local GPS (RF GPS) antenna is secure (if used).
Installation checklist Chapter 7: What’s Next and Cleanup 7-8 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 8 XXXXXXXXXXXX ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09286A73-1 JUL 2007 8-1 PRELIMINARY - UNDER DEVELOPMENT
Installation checklist Chapter 8: XXXXXXXXXXXX 8-2 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 9 XXXXXXXXXXXX ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09286A73-1 JUL 2007 9-1 PRELIMINARY - UNDER DEVELOPMENT
Installation checklist Chapter 9: XXXXXXXXXXXX 9-2 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 10 XXXXXXXXXXXX ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09286A73-1 JUL 2007 10-1 PRELIMINARY - UNDER DEVELOPMENT
Installation checklist Chapter 10: XXXXXXXXXXXX 10-2 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Chapter 11 XXXXXXXXXXXX ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 68P09286A73-1 JUL 2007 11-1 PRELIMINARY - UNDER DEVELOPMENT
Installation checklist Chapter 11: XXXXXXXXXXXX 11-2 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Appendix A Alternate RF Head Installation Procedure 68P09286A73-1 JUL 2007 A-1 PRELIMINARY - UNDER DEVELOPMENT
A-2 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Appendix B Alternate RGPS Installation 68P09286A73-1 JUL 2007 B-1 PRELIMINARY - UNDER DEVELOPMENT
B-2 68P09286A73-1 PRELIMINARY - UNDER DEVELOPMENT JUL 2007
Appendix C MMI Cable Fabrication 68P09286A73-1 JUL 2007 C-1 PRELIMINARY - UNDER DEVELOPMENT
