User's Manual
Table Of Contents
- Chapter 4: Acceptance Test Procedures
- Automated Acceptance Test Procedure
- Acceptance Tests - Test Set-up
- Abbreviated (All-inclusive) Acceptance Tests
- Individual Acceptance Tests
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (Rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX FER Acceptance Test
- Generating an ATP Report
- Updating Calibration Data Files
- Chapter 5: Prepare to Leave the Site
- Chapter 6: Troubleshooting
- Basic Troubleshooting: Overview
- Troubleshooting: Installation
- Cannot Log into Cell-Site
- Force LAN A Active (LMF Connection at I/O Panel LAN Connector)
- Force LAN A Active (LMF Connection at Service Shelf LAN Connector)
- Set the GLI IP Address
- Cannot Communicate with Power Meter
- Cannot Communicate with Communications System Analyzer
- Cannot Communicate with Signal Generator
- Troubleshooting: Download
- Troubleshooting: Calibration
- Basic Troubleshooting: RF Path Fault Isolation
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Checklist
- Troubleshooting: SCCP Backplane
- Troubleshooting: RFDS
- Module Front Panel LED Indicators and Connectors
- Troubleshooting: Span Control Link
- Appendix A: Data Sheets
- Appendix B: PN Offset/I & Q Offset Register Programming Information
- Appendix C: FRU Optimization / ATP Test Matrix
- Appendix D: BBX Gain Set Point vs. BTS Output
- Appendix E: CDMA Operating Frequency Programming Information
- Appendix F: Test Equipment Preparation
- Test Equipment Preparation
- Verifying and Setting GPIB Addresses
- Agilent E4406A Transmitter Tester GPIB Address
- Agilent E4432B Signal Generator GPIB Address
- Advantest R3267 Spectrum Analyzer GPIB Address
- Advantest R3562 Signal Generator GPIB Address
- Agilent 8935 Series E6380 (formerly HP 8935) Test Set GPIB Address
- Hewlett Packard HP 8921A and HP83236A/B GPIB Address
- Advantest R3465 Communications Test Set GPIB Address
- Motorola CyberTest GPIB Address
- HP 437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- RS232 GPIB Interface Adapter
- Test Equipment Inter-Unit Connection, Testing, and Control
- Inter-Unit Connection, Testing, and Control Settings
- HP 8921A with PCS Interface Test Equipment Connections
- HP 8921A with PCS Interface System Connectivity Test
- Pretest Set-up for HP 8921A
- Pretest Set-up for Agilent 8935
- Advantest R3465 Connection
- R3465 GPIB Clock Set-up
- Pretest Set-up for Advantest R3465
- Agilent 8932/E4432B Test Equipment Interconnection
- Agilent E4406A/E4432B Test Equipment Interconnection
- Advantest R3267/R3562 Test Equipment Interconnection
- Equipment Calibration
- Manual Cable Calibration
- Appendix G: Downloading ROM Code
- Appendix H: In-Service Calibration
- Appendix I: Packet Backhaul Configuration
- BTS Router Initial Configuration
- Terminal Setup
- Downloading Minimum Canned BTS Router Configuration Files
- Verifying IOS Canned Version of the CF Memory Card
- Replacing Installed BTS Router CF Memory Card IOS Version
- Background
- Equipment and Software Required for Verification Methods
- Required Publications
- Method 1: Replacement of Installed Router CF Card IOS Data
- Method 2: Using a CF Memory Card Reader for Replacement of Installed IOS Version and Changing File Sequence ...
- Change CF Memory Card File Sequence to Place IOS File First on the Card
- Verify and Upgrade ROMMON Version
- Recovery from BTS Router Boot to ROMMON
- Entering or Changing Router FE Interface IP Address
- Preparation for Site Turn-over
- Index
Index – continued
FEB 2005 1X SC 4812T Lite BTS Optimization/ATP Index-9
PRELIMINARY
Transmit TX path calibration, 3-115
Troubleshooting
DC Power Problems, 6-26
RF path fault isolation, 6-13
Set span configuration, 6-43
span problems, 6-41
TX and RX Signal Routing, 6-27
TX level accuracy fault isolation, 6-16
troubleshooting
communications system analyzer communication,
6-6
Ethernet LAN, 6-3
GLI IP address, 6-4
LMF login failure, 6-2
power meter communication, 6-5
signal generator communication, 6-6
TSU NAM, programming
description, 3-130
parameter ranges, 3-131
parameters, 3-130
procedure, 3-136
TX
acceptance tests
code domain power/noise floor, 4-20
equipment setup, 4-4
pilot time offset, 4-18
spectral purity mask, 4-13
spectrum analyzer display, 4-15
waveform quality (rho), 4-16
all inclusive TX ATP test, 4-6
antenna VSWR, test data sheets, A-9 , A-10
BLO test data sheets, A-7
level accuracy fault isolation, 6-16
output acceptance tests
code domain power noise, 4-11
pilot time offset, 4-11
waveform quality, 4-11
TX and RX Frequency vs Channel , E-2
TX and RX Signal Routing, SCCP Backplane
Troubleshooting, 6-27
TX Audit Test, 3-123
TX calibration, 3-118
All Cal/Audit, 3-119
set–up, 3-64 , 3-84
Advantest R3267, 3-66 , 3-86 , H-21
Advantest R3465, 3-65 , 3-85
Agilent 8935, 3-64 , 3-84
Agilent E4406A, 3-66 , 3-86 , H-21
CyberTest, 3-64 , 3-84
HP 8921A, 3-65 , 3-85
tx fine adjust, B-1
TX path. See transmit path
TX path calibration, 3-118
TX/RX OUT Connections, 4-3
U
Updating Calibration Data Files
Copy and Load Cal File to to CBSC, 4-26
Software Release caveats, 4-26
UTP, LMF to BTS connection, 3-18
V
verification during calibration, 3-110
Verify
test equipment used, test data sheets, A-1
TX output, 4-5
Verify GLI ROM code load, 3-38
W
Waveform quality (Rho), acceptance test procedure,
4-16
X
XCVR Backplane Troubleshooting, 6-22
Xircom Model PE3–10B2, LMF to BTS connection,
3-18