User's Manual
Table Of Contents
- Chapter 4: Acceptance Test Procedures
- Automated Acceptance Test Procedure
- Acceptance Tests - Test Set-up
- Abbreviated (All-inclusive) Acceptance Tests
- Individual Acceptance Tests
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (Rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX FER Acceptance Test
- Generating an ATP Report
- Updating Calibration Data Files
- Chapter 5: Prepare to Leave the Site
- Chapter 6: Troubleshooting
- Basic Troubleshooting: Overview
- Troubleshooting: Installation
- Cannot Log into Cell-Site
- Force LAN A Active (LMF Connection at I/O Panel LAN Connector)
- Force LAN A Active (LMF Connection at Service Shelf LAN Connector)
- Set the GLI IP Address
- Cannot Communicate with Power Meter
- Cannot Communicate with Communications System Analyzer
- Cannot Communicate with Signal Generator
- Troubleshooting: Download
- Troubleshooting: Calibration
- Basic Troubleshooting: RF Path Fault Isolation
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Checklist
- Troubleshooting: SCCP Backplane
- Troubleshooting: RFDS
- Module Front Panel LED Indicators and Connectors
- Troubleshooting: Span Control Link
- Appendix A: Data Sheets
- Appendix B: PN Offset/I & Q Offset Register Programming Information
- Appendix C: FRU Optimization / ATP Test Matrix
- Appendix D: BBX Gain Set Point vs. BTS Output
- Appendix E: CDMA Operating Frequency Programming Information
- Appendix F: Test Equipment Preparation
- Test Equipment Preparation
- Verifying and Setting GPIB Addresses
- Agilent E4406A Transmitter Tester GPIB Address
- Agilent E4432B Signal Generator GPIB Address
- Advantest R3267 Spectrum Analyzer GPIB Address
- Advantest R3562 Signal Generator GPIB Address
- Agilent 8935 Series E6380 (formerly HP 8935) Test Set GPIB Address
- Hewlett Packard HP 8921A and HP83236A/B GPIB Address
- Advantest R3465 Communications Test Set GPIB Address
- Motorola CyberTest GPIB Address
- HP 437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- RS232 GPIB Interface Adapter
- Test Equipment Inter-Unit Connection, Testing, and Control
- Inter-Unit Connection, Testing, and Control Settings
- HP 8921A with PCS Interface Test Equipment Connections
- HP 8921A with PCS Interface System Connectivity Test
- Pretest Set-up for HP 8921A
- Pretest Set-up for Agilent 8935
- Advantest R3465 Connection
- R3465 GPIB Clock Set-up
- Pretest Set-up for Advantest R3465
- Agilent 8932/E4432B Test Equipment Interconnection
- Agilent E4406A/E4432B Test Equipment Interconnection
- Advantest R3267/R3562 Test Equipment Interconnection
- Equipment Calibration
- Manual Cable Calibration
- Appendix G: Downloading ROM Code
- Appendix H: In-Service Calibration
- Appendix I: Packet Backhaul Configuration
- BTS Router Initial Configuration
- Terminal Setup
- Downloading Minimum Canned BTS Router Configuration Files
- Verifying IOS Canned Version of the CF Memory Card
- Replacing Installed BTS Router CF Memory Card IOS Version
- Background
- Equipment and Software Required for Verification Methods
- Required Publications
- Method 1: Replacement of Installed Router CF Card IOS Data
- Method 2: Using a CF Memory Card Reader for Replacement of Installed IOS Version and Changing File Sequence ...
- Change CF Memory Card File Sequence to Place IOS File First on the Card
- Verify and Upgrade ROMMON Version
- Recovery from BTS Router Boot to ROMMON
- Entering or Changing Router FE Interface IP Address
- Preparation for Site Turn-over
- Index
FEB 2005 1X SC 4812T Lite BTS Optimization/ATP Index-1
PRELIMINARY
Index
Numbers
10 MHz Rubidium Standard, optional test equipment,
1-11
10BaseT/10Base2 Converter, 1-7
10BaseT/10Base2 converter, LMF to BTS
connection, 3-18
2–way splitter, optional test equipment, 1-11
A
Abbreviated
RX acceptance test, all–inclusive, 4-6
TX acceptance test, all–inclusive, 4-6
Acceptance Test Procedure. See ATP
ACTIVE LED
GLI, 6-33
MCC–8/24 Card, 6-37
Advantest R3267 Spectrum Analyzer GPIB Address,
F-8
Advantest R3465 Communications Test Set GPIB
Address, F-14
Advantest R3562 Signal Generator GPIB Address,
F-9
Agilent 8935 Series E6380 (formerly HP 8935) Test
Set GPIB Address, F-10
Agilent E4406A, calibration, F-30
Agilent E4406A Transmitter Tester GPIB Address,
F-5
Agilent E4432B Signal Generator GPIB Address, F-7
Alarm Connector Location/Pin, 3-137
ALARM LED, GLI, 6-34
Alarm Monitor window, 3-139
Alarm Reporting Display, 3-139
All Cal/Audit procedure, 3-119
All RX ATP Test Procedure, 4-9
All tests fail on a single antenna, Troubleshooting,
RFDS, 6-29
All TX ATP Test Procedure, 4-8
All TX/RX ATP Test Procedure, 4-6
ATP
all inclusive TX acceptance test outline, 4-6
automated introduction, 4-1
code domain noise floor acceptance test procedure,
4-21
code domain power acceptance test procedure, 4-21
failure report generation, 4-25
FER test, frame error rate testing, 4-24
pilot time offset, 4-18
prerequisites, 4-2
spectral purity TX mask, 4-14
test matrix/detailed optimization, C-1
test set–up, 3-68 , 3-88
Advantest R3267/R3562
DRDCs, 3-71 , 3-91
TRDCs, 3-73 , 3-93
Advantest R3465, 3-68 , 3-88
Agilent 8935, DRDCs, 3-68 , 3-88
Agilent 8935/E4432B, DRDCs, 3-70 , 3-72 , 3-90
, 3-92
Agilent E4406A/E4432B
DRDCs, 3-70 , 3-90
TRDCs, 3-72 , 3-92
CyberTest, 3-68 , 3-88
HP 8921A, 1.9 GHz, 3-69 , 3-89
HP 8921A, 800 MHz, 3-69 , 3-89
waveform quality (Rho), 4-16
waveform quality (RHO) acceptance test procedure,
4-16
ATP – Reduced, 4-1
Attenuator, required test equipment, 1-9