User's Manual
Table Of Contents
- Chapter 4: Acceptance Test Procedures
- Automated Acceptance Test Procedure
- Acceptance Tests - Test Set-up
- Abbreviated (All-inclusive) Acceptance Tests
- Individual Acceptance Tests
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (Rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX FER Acceptance Test
- Generating an ATP Report
- Updating Calibration Data Files
- Chapter 5: Prepare to Leave the Site
- Chapter 6: Troubleshooting
- Basic Troubleshooting: Overview
- Troubleshooting: Installation
- Cannot Log into Cell-Site
- Force LAN A Active (LMF Connection at I/O Panel LAN Connector)
- Force LAN A Active (LMF Connection at Service Shelf LAN Connector)
- Set the GLI IP Address
- Cannot Communicate with Power Meter
- Cannot Communicate with Communications System Analyzer
- Cannot Communicate with Signal Generator
- Troubleshooting: Download
- Troubleshooting: Calibration
- Basic Troubleshooting: RF Path Fault Isolation
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Checklist
- Troubleshooting: SCCP Backplane
- Troubleshooting: RFDS
- Module Front Panel LED Indicators and Connectors
- Troubleshooting: Span Control Link
- Appendix A: Data Sheets
- Appendix B: PN Offset/I & Q Offset Register Programming Information
- Appendix C: FRU Optimization / ATP Test Matrix
- Appendix D: BBX Gain Set Point vs. BTS Output
- Appendix E: CDMA Operating Frequency Programming Information
- Appendix F: Test Equipment Preparation
- Test Equipment Preparation
- Verifying and Setting GPIB Addresses
- Agilent E4406A Transmitter Tester GPIB Address
- Agilent E4432B Signal Generator GPIB Address
- Advantest R3267 Spectrum Analyzer GPIB Address
- Advantest R3562 Signal Generator GPIB Address
- Agilent 8935 Series E6380 (formerly HP 8935) Test Set GPIB Address
- Hewlett Packard HP 8921A and HP83236A/B GPIB Address
- Advantest R3465 Communications Test Set GPIB Address
- Motorola CyberTest GPIB Address
- HP 437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- RS232 GPIB Interface Adapter
- Test Equipment Inter-Unit Connection, Testing, and Control
- Inter-Unit Connection, Testing, and Control Settings
- HP 8921A with PCS Interface Test Equipment Connections
- HP 8921A with PCS Interface System Connectivity Test
- Pretest Set-up for HP 8921A
- Pretest Set-up for Agilent 8935
- Advantest R3465 Connection
- R3465 GPIB Clock Set-up
- Pretest Set-up for Advantest R3465
- Agilent 8932/E4432B Test Equipment Interconnection
- Agilent E4406A/E4432B Test Equipment Interconnection
- Advantest R3267/R3562 Test Equipment Interconnection
- Equipment Calibration
- Manual Cable Calibration
- Appendix G: Downloading ROM Code
- Appendix H: In-Service Calibration
- Appendix I: Packet Backhaul Configuration
- BTS Router Initial Configuration
- Terminal Setup
- Downloading Minimum Canned BTS Router Configuration Files
- Verifying IOS Canned Version of the CF Memory Card
- Replacing Installed BTS Router CF Memory Card IOS Version
- Background
- Equipment and Software Required for Verification Methods
- Required Publications
- Method 1: Replacement of Installed Router CF Card IOS Data
- Method 2: Using a CF Memory Card Reader for Replacement of Installed IOS Version and Changing File Sequence ...
- Change CF Memory Card File Sequence to Place IOS File First on the Card
- Verify and Upgrade ROMMON Version
- Recovery from BTS Router Boot to ROMMON
- Entering or Changing Router FE Interface IP Address
- Preparation for Site Turn-over
- Index
Verify and Upgrade ROMMON Version – continued
I-66 1X SC 4812T Lite BTS Optimization/ATP FEB 2005
PRELIMINARY
Required Publications
The following publication is required to perform procedures in this
section:
S MWR1941 Wireless Mobile Edge Router Software Configuration
Guide; part number 78–13983–01
Method 1: In–Router
Verification and Replacement
of Installed ROMMON Version
Description
This procedure covers using an LMF Computer equipped with a TFTP
Server Application to perform the following activities.:
1. Verify that the ROMMON Version loaded and running on a BTS
Router
2. Replace the ROMMON Version installed in a BTS Router
Additional Required Equipment/Software
For this method, the following equipment and Software Application is
required in addition to the common items required for both methods.:
S Cable, Ethernet Crossover, Category 5E or better, unshielded twisted
pair, two 8–contact Modular Plugs, in one of the following lengths, as
determined necessary:
– 0.3 m (11.8 in) (Motorola Part Number 3088643C07)
– 0.6 m (23.6 in)(Motorola Part Number 3088643C13)
– 1.0 m (39.4 in) (Motorola Part Number 3088643C15)
– 2.1 m (84 in) (Motorola Part Number 3088643C08)
– 3.0 m (120 in) (Motorola Part Number 3088643C09)
S A TFTP Server Software Application; refer to the Setting Up the
TFTP Server – Procedure in Cellular System Administration – CDMA
OnLine Documentation such as:
– Cisco TFTP Server
– PumpKIN TFTP Server
– Any other equivalent TFTP Server Application
Prerequisites
The following items are required prior to performing this procedure.:
S The LMF Computer and BTS Router have been prepared for TFTP
File Transfer and are operating as they would be after performing the
procedures in Table I-4, Table I-5, Table I-6, and Steps 1 through 10
of Table I-7.
S A copy of the required ROMMON Version is loaded into the TFTP
Default Directory of the LMF Computer.
Verifying and replacing installed ROMMON Version
Perform the procedure in Table I-13 to verify and, if necessary, replace
the installed ROMMON Version using the TFTP Server Application..
I