User's Manual
Table Of Contents
- Chapter 4: Acceptance Test Procedures
- Automated Acceptance Test Procedure
- Acceptance Tests - Test Set-up
- Abbreviated (All-inclusive) Acceptance Tests
- Individual Acceptance Tests
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (Rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX FER Acceptance Test
- Generating an ATP Report
- Updating Calibration Data Files
- Chapter 5: Prepare to Leave the Site
- Chapter 6: Troubleshooting
- Basic Troubleshooting: Overview
- Troubleshooting: Installation
- Cannot Log into Cell-Site
- Force LAN A Active (LMF Connection at I/O Panel LAN Connector)
- Force LAN A Active (LMF Connection at Service Shelf LAN Connector)
- Set the GLI IP Address
- Cannot Communicate with Power Meter
- Cannot Communicate with Communications System Analyzer
- Cannot Communicate with Signal Generator
- Troubleshooting: Download
- Troubleshooting: Calibration
- Basic Troubleshooting: RF Path Fault Isolation
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Checklist
- Troubleshooting: SCCP Backplane
- Troubleshooting: RFDS
- Module Front Panel LED Indicators and Connectors
- Troubleshooting: Span Control Link
- Appendix A: Data Sheets
- Appendix B: PN Offset/I & Q Offset Register Programming Information
- Appendix C: FRU Optimization / ATP Test Matrix
- Appendix D: BBX Gain Set Point vs. BTS Output
- Appendix E: CDMA Operating Frequency Programming Information
- Appendix F: Test Equipment Preparation
- Test Equipment Preparation
- Verifying and Setting GPIB Addresses
- Agilent E4406A Transmitter Tester GPIB Address
- Agilent E4432B Signal Generator GPIB Address
- Advantest R3267 Spectrum Analyzer GPIB Address
- Advantest R3562 Signal Generator GPIB Address
- Agilent 8935 Series E6380 (formerly HP 8935) Test Set GPIB Address
- Hewlett Packard HP 8921A and HP83236A/B GPIB Address
- Advantest R3465 Communications Test Set GPIB Address
- Motorola CyberTest GPIB Address
- HP 437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- RS232 GPIB Interface Adapter
- Test Equipment Inter-Unit Connection, Testing, and Control
- Inter-Unit Connection, Testing, and Control Settings
- HP 8921A with PCS Interface Test Equipment Connections
- HP 8921A with PCS Interface System Connectivity Test
- Pretest Set-up for HP 8921A
- Pretest Set-up for Agilent 8935
- Advantest R3465 Connection
- R3465 GPIB Clock Set-up
- Pretest Set-up for Advantest R3465
- Agilent 8932/E4432B Test Equipment Interconnection
- Agilent E4406A/E4432B Test Equipment Interconnection
- Advantest R3267/R3562 Test Equipment Interconnection
- Equipment Calibration
- Manual Cable Calibration
- Appendix G: Downloading ROM Code
- Appendix H: In-Service Calibration
- Appendix I: Packet Backhaul Configuration
- BTS Router Initial Configuration
- Terminal Setup
- Downloading Minimum Canned BTS Router Configuration Files
- Verifying IOS Canned Version of the CF Memory Card
- Replacing Installed BTS Router CF Memory Card IOS Version
- Background
- Equipment and Software Required for Verification Methods
- Required Publications
- Method 1: Replacement of Installed Router CF Card IOS Data
- Method 2: Using a CF Memory Card Reader for Replacement of Installed IOS Version and Changing File Sequence ...
- Change CF Memory Card File Sequence to Place IOS File First on the Card
- Verify and Upgrade ROMMON Version
- Recovery from BTS Router Boot to ROMMON
- Entering or Changing Router FE Interface IP Address
- Preparation for Site Turn-over
- Index
Replacing Installed BTS Router CF Memory Card IOS Version – continued
FEB 2005 1X SC 4812T Lite BTS Optimization/ATP I-43
PRELIMINARY
Method 1: Replacement of
Installed Router CF Card IOS
Data
Description
This procedure covers using an LMF Computer equipped with a TFTP
Server Application to perform the following activities::
1. Verify that the IOS Version is loaded on a CF Memory Card and
running on a BTS Router.
2. Replace the IOS Version installed in a BTS Router.
3. Ensure the IOS File is the first file on the CF Memory Card
Additional Required Equipment/Software
For this method, the following Software Application is required in
addition to the common items required for both methods.:
S Cable, Ethernet Crossover, Category 5E or better, unshielded twisted
pair, two 8–contact Modular Plugs, in one of the following lengths, as
determined necessary:
– 0.3 m (11.8 in) (Motorola Part Number 3088643C07)
– 0.6 m (23.6 in)(Motorola Part Number 3088643C13)
– 1.0 m (39.4 in) (Motorola Part Number 3088643C15)
– 2.1 m (84 in) (Motorola Part Number 3088643C08)
– 3.0 m (120 in) (Motorola Part Number 3088643C09)
S A TFTP Server Software Application (refer to the Setting Up the
TFTP Server – Procedure in Cellular System Administration – CDMA
OnLine Documentation such as:
– Cisco TFTP Server
– PumpKIN TFTP Server
– Any other equivalent TFTP Server Application
Prerequisites
The following are required prior to performing this procedure::
S The LMF Computer and BTS Router have been prepared for TFTP
File Transfer and are operating as they would be after performing the
procedures in Table I-4, Table I-5, Table I-6, and Steps 1 through 10
of Table I-7.
S A copy of the required IOS Version is loaded into the TFTP Default
Directory of the LMF Computer
Replacing Installed IOS Version and Verifying File Sequence
Position
Perform the procedure in Table I-10 to replace the installed IOS Version
using the TFTP Server Application, and ensure the IOS File is first in
the stored File Sequence on the CF Memory Card..
I