User's Manual
Table Of Contents
- Chapter 4: Acceptance Test Procedures
- Automated Acceptance Test Procedure
- Acceptance Tests - Test Set-up
- Abbreviated (All-inclusive) Acceptance Tests
- Individual Acceptance Tests
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (Rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX FER Acceptance Test
- Generating an ATP Report
- Updating Calibration Data Files
- Chapter 5: Prepare to Leave the Site
- Chapter 6: Troubleshooting
- Basic Troubleshooting: Overview
- Troubleshooting: Installation
- Cannot Log into Cell-Site
- Force LAN A Active (LMF Connection at I/O Panel LAN Connector)
- Force LAN A Active (LMF Connection at Service Shelf LAN Connector)
- Set the GLI IP Address
- Cannot Communicate with Power Meter
- Cannot Communicate with Communications System Analyzer
- Cannot Communicate with Signal Generator
- Troubleshooting: Download
- Troubleshooting: Calibration
- Basic Troubleshooting: RF Path Fault Isolation
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Checklist
- Troubleshooting: SCCP Backplane
- Troubleshooting: RFDS
- Module Front Panel LED Indicators and Connectors
- Troubleshooting: Span Control Link
- Appendix A: Data Sheets
- Appendix B: PN Offset/I & Q Offset Register Programming Information
- Appendix C: FRU Optimization / ATP Test Matrix
- Appendix D: BBX Gain Set Point vs. BTS Output
- Appendix E: CDMA Operating Frequency Programming Information
- Appendix F: Test Equipment Preparation
- Test Equipment Preparation
- Verifying and Setting GPIB Addresses
- Agilent E4406A Transmitter Tester GPIB Address
- Agilent E4432B Signal Generator GPIB Address
- Advantest R3267 Spectrum Analyzer GPIB Address
- Advantest R3562 Signal Generator GPIB Address
- Agilent 8935 Series E6380 (formerly HP 8935) Test Set GPIB Address
- Hewlett Packard HP 8921A and HP83236A/B GPIB Address
- Advantest R3465 Communications Test Set GPIB Address
- Motorola CyberTest GPIB Address
- HP 437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- RS232 GPIB Interface Adapter
- Test Equipment Inter-Unit Connection, Testing, and Control
- Inter-Unit Connection, Testing, and Control Settings
- HP 8921A with PCS Interface Test Equipment Connections
- HP 8921A with PCS Interface System Connectivity Test
- Pretest Set-up for HP 8921A
- Pretest Set-up for Agilent 8935
- Advantest R3465 Connection
- R3465 GPIB Clock Set-up
- Pretest Set-up for Advantest R3465
- Agilent 8932/E4432B Test Equipment Interconnection
- Agilent E4406A/E4432B Test Equipment Interconnection
- Advantest R3267/R3562 Test Equipment Interconnection
- Equipment Calibration
- Manual Cable Calibration
- Appendix G: Downloading ROM Code
- Appendix H: In-Service Calibration
- Appendix I: Packet Backhaul Configuration
- BTS Router Initial Configuration
- Terminal Setup
- Downloading Minimum Canned BTS Router Configuration Files
- Verifying IOS Canned Version of the CF Memory Card
- Replacing Installed BTS Router CF Memory Card IOS Version
- Background
- Equipment and Software Required for Verification Methods
- Required Publications
- Method 1: Replacement of Installed Router CF Card IOS Data
- Method 2: Using a CF Memory Card Reader for Replacement of Installed IOS Version and Changing File Sequence ...
- Change CF Memory Card File Sequence to Place IOS File First on the Card
- Verify and Upgrade ROMMON Version
- Recovery from BTS Router Boot to ROMMON
- Entering or Changing Router FE Interface IP Address
- Preparation for Site Turn-over
- Index
Verifying IOS Canned Version of the CF Memory Card – continued
I-32 1X SC 4812T Lite BTS Optimization/ATP FEB 2005
PRELIMINARY
Table I-7: Transfer Canned Configuration Files to the BTS Router Using a TFTP Server
n ActionStep
26 Verify that the BTS Router reboots without displaying the rommon 1 > Prompt or Error Messages
related to Port Configurations.
S If the BTS Router boots to the ROMMON Prompt, proceed to the Recovery from BTS Router
Boot to ROMMON section of this appendix.
27 Using the tagging materials, tag the BTS Router to clearly identify the installed configuration
[blue (BTSRTR1) or red (BTSRTR2)].
28 Remove the CF Memory from the BTS Router by performing the procedure in the 1X SC4812T
Lite BTS FRU manual (68P09262A60) Manual.
29 Mark the installed configuration (blue or red) on the Card Label.
30 Install the card in the BTS Router by performing the procedure in the 1X SC4812T Lite BTS FRU
manual (68P09262A60)
31 If an additional BTS Router needs have the Canned Configuration installed, perform the following
actions.
31a Disconnect the cabling from the BTS Router.
31b Remove power from the BTS Router and disconnect it from the Power Supply Module.
31c Repeat the procedures in Table I-5, Table I-6, and this table (Table I-7) using the additional BTS
Router.
32 If no additional BTS Routers must be configured, perform Steps 31a and 31b, then proceed to
Step 33.
33 On the LMF Computer, shut down the TFTP Server Application and exit the HyperTerminal
Session.
34 If no additional TFTP Transfer activities are to be performed, change the NIC IP Address and
Subnet Mask back to those for LMF–BTS Communication recorded in Table I-4, Step 9b.
! CAUTION
If the BTS 10base–2 LAN IP Address and Subnet Mask for the LMF Computer’s NIC are not
restored, the LMF can not log into a BTS when attempting to perform a BTS Optimization or
ATP.
I