User's Manual
Table Of Contents
- Chapter 4: Acceptance Test Procedures
- Automated Acceptance Test Procedure
- Acceptance Tests - Test Set-up
- Abbreviated (All-inclusive) Acceptance Tests
- Individual Acceptance Tests
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (Rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX FER Acceptance Test
- Generating an ATP Report
- Updating Calibration Data Files
- Chapter 5: Prepare to Leave the Site
- Chapter 6: Troubleshooting
- Basic Troubleshooting: Overview
- Troubleshooting: Installation
- Cannot Log into Cell-Site
- Force LAN A Active (LMF Connection at I/O Panel LAN Connector)
- Force LAN A Active (LMF Connection at Service Shelf LAN Connector)
- Set the GLI IP Address
- Cannot Communicate with Power Meter
- Cannot Communicate with Communications System Analyzer
- Cannot Communicate with Signal Generator
- Troubleshooting: Download
- Troubleshooting: Calibration
- Basic Troubleshooting: RF Path Fault Isolation
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Checklist
- Troubleshooting: SCCP Backplane
- Troubleshooting: RFDS
- Module Front Panel LED Indicators and Connectors
- Troubleshooting: Span Control Link
- Appendix A: Data Sheets
- Appendix B: PN Offset/I & Q Offset Register Programming Information
- Appendix C: FRU Optimization / ATP Test Matrix
- Appendix D: BBX Gain Set Point vs. BTS Output
- Appendix E: CDMA Operating Frequency Programming Information
- Appendix F: Test Equipment Preparation
- Test Equipment Preparation
- Verifying and Setting GPIB Addresses
- Agilent E4406A Transmitter Tester GPIB Address
- Agilent E4432B Signal Generator GPIB Address
- Advantest R3267 Spectrum Analyzer GPIB Address
- Advantest R3562 Signal Generator GPIB Address
- Agilent 8935 Series E6380 (formerly HP 8935) Test Set GPIB Address
- Hewlett Packard HP 8921A and HP83236A/B GPIB Address
- Advantest R3465 Communications Test Set GPIB Address
- Motorola CyberTest GPIB Address
- HP 437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- RS232 GPIB Interface Adapter
- Test Equipment Inter-Unit Connection, Testing, and Control
- Inter-Unit Connection, Testing, and Control Settings
- HP 8921A with PCS Interface Test Equipment Connections
- HP 8921A with PCS Interface System Connectivity Test
- Pretest Set-up for HP 8921A
- Pretest Set-up for Agilent 8935
- Advantest R3465 Connection
- R3465 GPIB Clock Set-up
- Pretest Set-up for Advantest R3465
- Agilent 8932/E4432B Test Equipment Interconnection
- Agilent E4406A/E4432B Test Equipment Interconnection
- Advantest R3267/R3562 Test Equipment Interconnection
- Equipment Calibration
- Manual Cable Calibration
- Appendix G: Downloading ROM Code
- Appendix H: In-Service Calibration
- Appendix I: Packet Backhaul Configuration
- BTS Router Initial Configuration
- Terminal Setup
- Downloading Minimum Canned BTS Router Configuration Files
- Verifying IOS Canned Version of the CF Memory Card
- Replacing Installed BTS Router CF Memory Card IOS Version
- Background
- Equipment and Software Required for Verification Methods
- Required Publications
- Method 1: Replacement of Installed Router CF Card IOS Data
- Method 2: Using a CF Memory Card Reader for Replacement of Installed IOS Version and Changing File Sequence ...
- Change CF Memory Card File Sequence to Place IOS File First on the Card
- Verify and Upgrade ROMMON Version
- Recovery from BTS Router Boot to ROMMON
- Entering or Changing Router FE Interface IP Address
- Preparation for Site Turn-over
- Index
Power Delta Calibration – continued
H-4 1X SC 4812T Lite BTS Optimization/ATP FEB 2005
PRELIMINARY
Table H-1: Agilent E4406A Power Delta Calibration Procedure
n ActionStep
2 Ensure that the E4406A and E4432B are connected as shown in Figure F-18.
3 Connect a short RF Cable from the E4432B RF OUTPUT Connector the HP437 Power Meter
Power Sensor.
– Refer to Figure H-1.
4 Set the E4432B Signal Generator by performing the following actions.
4a Press Preset to exit any modes for which the Signal Generator is configured.
4b Press Frequency and enter the frequency of the channel to be calibrated on the Numeric Keypad.
4c Using the Softkeys to the right of the screen, select the Frequency Range to be measured; for
example: MHz.
4d Press Amplitude and, using the Numeric Keypad, set the Signal Amplitude to 0 (zero).
4e Using the Softkeys, set the measurement type to dBm.
5 On the E4432B, press RF On/Off to toggle the RF Output to RF ON.
– Note that the RF On/Off Status in the Screen Display changes.
6 Measure and record the Value Reading on the HP437 Power Meter as result.
A____________________
7 On the E4432B, press RF On/Off to toggle the RF Output to RF OFF.
– Note that the RF On/Off Status in the Screen Display changes.
8 Disconnect the short RF Cable from the HP437 Power Meter Power Sensor, and connect it to the
RF INPUT Connector on the E4406A Transmitter Tester.
– Refer to Figure H-2.
* IMPORTANT
Do not change the Frequency and Amplitude Settings on the E4432B when performing the
following actions.
9 Set the E4406A by performing the following actions.
9a Press Preset to exit any modes for which the Transmitter Tester is configured.
9b Press MODE and, using the Softkeys to the right of the screen, select cdmaOne.
9c Press MEASURE and, using the Softkeys, select spectrum.
9d Press Frequency and, using the Softkeys, select Center Frequency.
9e Enter the frequency of the channel to be calibrated using the Numeric Keypad.
9f Using the Softkeys, select the Frequency Range to be measured; for example, MHz.
9g Press Input/Output and, using the Softkeys, select Input Atten.
9h Using the Numeric Keypad, set Input Atten to 0 (zero) and, using the Softkeys, select dB.
table continued on next page
H