User's Manual

List of Figures – continued
FEB 2005 1X SC 4812T Lite BTS Optimization/ATP vii
PRELIMINARY
Figure 3-38: IS–95A/B and CDMA2000 1X ATP Test Set–up With DRFs –
Advantest R3267/3562 Test Equipment 3-94 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-39: IS–95A/B and CDMA2000 1X ATP Test Set–up With TRFs –
Agilent Test Equipment 3-95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-40: IS–95A/B and CDMA2000 1X ATP Test Set–up With TRFs –
Advantest R3267/3562 Test Equipment 3-96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-41: IS–95A/B and CDMA2000 1X Optimization/ATP Test Set–up –
Agilent E7495A 3-97 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-42: Calibration Set–up for TX/Duplexed RX Test Cabling
using a Signal Generator and a Spectrum Analyzer 3-108 . . . . . . . . . . . . . . . . . . . . .
Figure 3-43: Calibration Set–up for Non–Duplexed RX Test Cabling
using a Signal Generator and a Spectrum Analyzer 3-109 . . . . . . . . . . . . . . . . . . . . .
Figure 3-44: Alarm Connector Location and Connector Pin Numbering 3-140 . . . . .
Figure 3-45: SCCP Cage 3-141 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-46: AMR Connector Pin Numbering 3-142 . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-1: TX and RX Antenna Connections on I/O Panel 4-3 . . . . . . . . . . . . . . .
Figure 4-2: TX Mask Verification Spectrum Analyzer Display 4-15 . . . . . . . . . . . . .
Figure 4-3: Code Domain Analyzer CD Power/Noise Floor Display Examples 4-22
Figure 6-1: TX Output Fault Isolation Flowchart 6-17 . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-2: CSM Front Panel LED and Monitor Ports 6-34 . . . . . . . . . . . . . . . . . . .
Figure 6-3: GLI3 Front Panel 6-37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-4: MCC24 and MCC–1X Front Panel LEDs and LED Indications 6-40 . .
Figure 6-5: CLPA Module 6-41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-6: MGLI/GLI Board MMI Connection Detail 6-43 . . . . . . . . . . . . . . . . . . .
Figure E-1: North America PCS Frequency Spectrum (CDMA Allocation) E-1 . . .
Figure E-2: North American Cellular Telephone System Frequency Spectrum
(CDMA Allocation) E-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-1: Agilent E7495A Pre–Power Sensor Calibration Connection F-3 . . . . .
Figure F-2: Agilent E7495A Power Sensor Calibration Connection F-4 . . . . . . . . .
Figure F-3: Setting Agilent E4406A GPIB Address F-5 . . . . . . . . . . . . . . . . . . . . .
Figure F-4: Setting Agilent E4432B GPIB Address F-7 . . . . . . . . . . . . . . . . . . . . .
Figure F-5: Setting Advantest R3267 GPIB Address F-8 . . . . . . . . . . . . . . . . . . . . .
Figure F-6: Advantest R3562 GPIB Address Switch Setting F-9 . . . . . . . . . . . . . .
Figure F-7: Agilent 8935 Test Set F-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-8: HP 8921A and HP 83236A/B F-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-9: R3465 Communications Test Set F-14 . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-10: HP 437 Power Meter F-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-11: Gigatronics 8541C Power Meter Detail F-17 . . . . . . . . . . . . . . . . . . . .
Figure F-12: RS232 GPIB Interface Adapter F-18 . . . . . . . . . . . . . . . . . . . . . . . . . . .