User Manual

Adjusting for loss68P09255A57-2
Aug 2002
SC4812ET Optimization/ATP Manual Software Release R16.1.x.x
PRELIMINARY
3-77
- The second breakdown of the array is per sector. Three sectors are
allowed.
Table 3-39: BTS.cal File Array (Per Sector)
BBX Sectorization TX RX RX Diversity
Slot[1] (Primary BBXs 1 through 12)
1 (Omni)
3-Sector,
C[1]-C[20] C[241]-C[260] C[481]-C[500]
2
3-Sector,
1st
C[21]-C[40] C[261]-C[280] C[501]-C[520]
3
6 Sector,
Carrier
C[41]-C[60] C[281]-C[300] C[521]-C[540]
4
1st
Carrier
3-Sector,
C[61]-C[80] C[301]-C[320] C[541]-C[560]
5
Carrier
3-Sector,
3rd
C[81]-C[100] C[321]-C[340] C[561]-C[580]
6
Carrier
C[101]-C[120] C[341]-C[360] C[581]-C[600]
7
3-Sector,
C[121]-C[140] C[361]-C[380] C[601]-C[620]
8
3-Sector,
2nd
C[141]-C[160] C[381]-C[400] C[621]-C[640]
9
6 Sector,
Carrier
C[161]-C[180] C[401]-C[420] C[641]-C[660]
10
2nd
Carrier
3-Sector,
C[181]-C[200] C[421]-C[440] C[661]-C[680]
11
Carrier
3-Sector,
4th
C[201]-C[220] C[441]-C[460] C[681]-C[700]
12
Carrier
C[221]-C[240] C[461]-C[480] C[701]-C[720]
Slot[20] (Redundant BBX-13)
1 (Omni)
3-Sector,
C[1]-C[20] C[241]-C[260] C[481]-C[500]
2
3-Sector,
1st
C[21]-C[40] C[261]-C[280] C[501]-C[520]
3
6 Sector,
Carrier
C[41]-C[60] C[281]-C[300] C[521]-C[540]
4
1st
Carrier
3-Sector,
C[61]-C[80] C[301]-C[320] C[541]-C[560]
5
Carrier
3-Sector,
3rd
C[81]-C[100] C[321]-C[340] C[561]-C[580]
6
Carrier
C[101]-C[120] C[341]-C[360] C[581]-C[600]
7
3-Sector,
C[121]-C[140] C[361]-C[380] C[601]-C[620]
8
3-Sector,
2nd
C[141]-C[160] C[381]-C[400] C[621]-C[640]
9
6 Sector,
Carrier
C[161]-C[180] C[401]-C[420] C[641]-C[660]
10
2nd
Carrier
3-Sector,
C[181]-C[200] C[421]-C[440] C[661]-C[680]
11
Carrier
3-Sector,
4th
C[201]-C[220] C[441]-C[460] C[681]-C[700]
12
Carrier
C[221]-C[240] C[461]-C[480] C[701]-C[720]
 Refer to the hard copy of the file. As you can see, 10 calibration
points per sector are supported for each branch. Two entries are
required for each calibration point.
 The first value (all odd entries) refer to the CDMA channel
(frequency) the BLO is measured at. The second value (all even
entries) is the power set level. The valid range for PwrLvlAdj is from
2500 to 27500 (2500 corresponds to -125 dBm and 27500
corresponds to +125 dBm).
 The 20 calibration entries for each slot/branch combination must be
stored in order of increasing frequency. If less than 10 points
(frequencies) are calibrated, the largest frequency that is calibrated is
repeated to fill out the 10 points.
3