User's Manual Part 1

xii 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU Jun 2004
DRAFT
List of Tables
1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU
Software Release 2.16.5.X
FCC Part 68 Registered Devices xxiv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1-1: Abbreviations and Acronyms 1-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1-2: 1900 MHz TX and RX Frequency vs. Channel 1-9 . . . . . . . . . . . . . . . .
Table 1-3: Recommended Tools and Materials for Rack Mounting 1-11 . . . . . . . . . .
Table 1-4: CCP2 Shelf Card/Module Device ID Numbers for Logical BTS 1-21 . . .
Table 1-5: Shelf Device ID Numbers 1-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-1: Procedure to Prepare the Site for the BTS 2-6 . . . . . . . . . . . . . . . . . . . .
Table 2-2: Recommended Unpacking Tools 2-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-3: Unpacking Equipment from a Cardboard or Wood Container 2-11 . . . . .
Table 2-4: Procedure to Remove Outdoor Equipment from Container 2-11 . . . . . . .
Table 2-5: Procedure to Remove Indoor Equipment from Container 2-13 . . . . . . . . .
Table 2-6: Installation Dimensions for the BTS 2-14 . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-7: Minimum Clearances for the BTS 2-14 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-8: Installation Dimensions for the cCLPA 2-16 . . . . . . . . . . . . . . . . . . . . . . .
Table 2-9: Minimum Clearances for the cCLPA 2-16 . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-10: Installation Dimensions for the TME 2-20 . . . . . . . . . . . . . . . . . . . . . . .
Table 2-11: Minimum Clearances for the TME 2-20 . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-12: Installation Dimensions for the PDE 2-23 . . . . . . . . . . . . . . . . . . . . . . . .
Table 2-13: Minimum Clearances for the PDE 2-23 . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-1: Cable Descriptions and Part Numbers 3-2 . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-2: Cables Needed for Antenna Connections 3-6 . . . . . . . . . . . . . . . . . . . . .
Table 3-3: Pin and Signal Information for Cable B (Antenna Cable) 3-6 . . . . . . . .
Table 3-4: Cables Needed for Span/RGPS Connections 3-7 . . . . . . . . . . . . . . . . . .
Table 3-5: Pin/Signal Information for Span Cable 3-7 . . . . . . . . . . . . . . . . . . . . . . .
Table 3-6: Cables Needed for Span/RGPS Connections 3-8 . . . . . . . . . . . . . . . . . .
Table 3-7: RGPS Pin/Signal Name Information 3-8 . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-8: Cabling for Local GPS 3-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-9: Local GPS Antenna Mounting Considerations 3-12 . . . . . . . . . . . . . . . . .
Table 4-1: Procedure to Attach Mounting Plate to Rack 4-6 . . . . . . . . . . . . . . . . . .