User's Manual Part 1

List of Figures – continued
Mar 2001
v
SCt4812T CDMA BTS Optimization/ATP
DRAFT
Figure 3-6: –48 V SC 4812T Starter Frame I/O Plate 3-17. . . . . . . . . . . . . . . . . . . .
Figure 3-7: CDMA LMF Computer Common MMI Connections 3-24. . . . . . . . . . .
Figure 3-8: Null Modem Cable Detail 3-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-9: CSM MMI terminal connection 3-35. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-10: Cable Calibration Test Setup 3-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-11: TX Calibration Test Setup (CyberTest, HP 8935,
and Advantest) 3-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-12: TX Calibration Test Setup HP 8921A W/PCS for 1.7/1.9 GHz 3-48. .
Figure 3-13: Optimization/ATP Test Setup Calibration (CyberTest,
HP 8935 and Advantest) 3-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-14: Optimization/ATP Test Setup HP 8921A 3-50. . . . . . . . . . . . . . . . . . .
Figure 3-15: Typical TX ATP Setup with Directional Coupler (shown
with and without RFDS) 3-51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-16: Typical RX ATP Setup with Directional Coupler (shown
with or without RFDS) 3-52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-17: Calibrating Test Equipment Setup for TX BLO and TX
ATP Tests (using Signal Generator and Spectrum Analyzer) 3-59. . . . . . . . . . . . . . .
Figure 3-18: Calibrating Test Equipment Setup for RX ATP Test (using
Signal Generator and Spectrum Analyzer) 3-60. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-19: SC 4812T C–CCP Shelf 3-88. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-20: –48 V BTS Power Conversion Shelf 3-88. . . . . . . . . . . . . . . . . . . . . . .
Figure 3-21: +27 V BTS C-CCP Fan Modules 3-90. . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-22: –48 V BTS C-CCP and Power Conversion Shelf Fan Modules 3-90. .
Figure 3-23: +27 V SC 4812T Starter Frame I/O Plate 3-94. . . . . . . . . . . . . . . . . . .
Figure 3-24: Alarm Connector Location and Connector Pin Numbering 3-98. . . . .
Figure 3-25: AMR Connector Pin Numbering 3-99. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-1: TX Mask Verification Spectrum Analyzer Display 4-7. . . . . . . . . . . . .
Figure 4-2: Code Domain Power and Noise Floor Levels 4-11. . . . . . . . . . . . . . . . .
Figure 5-1: MGLI2/SGLI2 MMI Port Connection 5-4. . . . . . . . . . . . . . . . . . . . . . .
Figure 5-2: Site and Span I/O Boards T1 Span Connections 5-8. . . . . . . . . . . . . . .
Figure 6-1: CSM Front Panel Indicators & Monitor Ports 6-21. . . . . . . . . . . . . . . . .
Figure 6-2: GLI2 Front Panel 6-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-3: MCC24/8E Front Panel 6-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure E-1: North American PCS 1900 MHz Frequency
Spectrum (CDMA Allocation) E-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure E-2: North American Cellular Telephone System Frequency
Spectrum (CDMA Allocation) E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure E-3: 1700 MHz PCS Frequency Spectrum (CDMA Allocation) E-6. . . . . .
Figure F-1: Calibrating Test Setup Components F-6. . . . . . . . . . . . . . . . . . . . . . . .
Figure F-2: Cable Calibration using Advantest R3465 F-10. . . . . . . . . . . . . . . . . . .
. . . continued on next page