User's Manual

Cabinet Cabling

– continued

DRAFT

4812ET RF and Power Cabinet Hardware Installation Manual

Apr 2001

V04.03

Table 5-2: Materials Required for Earth Ground Cabling 89. . . . .

Table 5-3: Procedure to Install RF Cabinet Earth Ground Cables 89

Table 5-4: Materials Required for Alarm, Span, and Modem Cabling 92

Table 5-5: Alarm, Span, and Modem Line Cable Installation 92. .

Table 5-6: External Alarm Connector Characteristics and 94. . . . .

Table 5-7: External Alarm Connector and Requirements 94. . . . . .

Table 5-8: Materials Required for RGPS Cabling 97. . . . . . . . . . .

Table 5-9: RGPS Cable Install Procedure 98. . . . . . . . . . . . . . . . .

Table 5-10: Punch Block for the Remote GPS 98. . . . . . . . . . . . . .

Table 5-11: Materials Required for RF GPS Cabling 99. . . . . . . . .

Table 5-12: RF GPS Cable Install Procedure 99. . . . . . . . . . . . . . .

Table 5-13: Materials Required for LFR Cabling 100. . . . . . . . . . .

Table 5-14: LFR Cable Install Procedure 100. . . . . . . . . . . . . . . . . .

Table 5-15: Pin/Signal Information for LFR Cable 100. . . . . . . . . .

Table 5-16: BTS Sector/Carrier Configurations 101. . . . . . . . . . . . .

Table 5-17: Antenna Cables for Duplex 120 Degree Sector 101. . .

Table 5-18: Antenna Cables for Duplex 60 Degree Sector 102. . . .

Table 5-19: Antenna Cables for Non–Duplexed 120 Degree 96. .

Table 5-20: Antenna Cables Non–duplexed 60 Degree Sector 103.

Table 5-21: Install Main RF Cabling (Rear Wall of RF Cabinet) 104

Table 5-22: Install Main RF Cabling (Bottom of RF Cabinet) 105.

Table 5-23: Materials Required for Earth Ground Cabling 106. . . .

Table 5-24: Procedure to Install Earth Ground Cables 106. . . . . . . .

Table 5-25: Materials Required for Power Cabinet Alarm Cabling 109

Table 5-26: Power Cabinet Alarm Cable Install Procedure 109. . . .

Table 5-27: Pin–Out for Power Cabinet Punch Block 110. . . . . . . .

Table 5-28: Wire, Lug, and Die Table 111. . . . . . . . . . . . . . . . . . . .

Table 5-29: Procedure to Install DC Power Cables 112. . . . . . . . . .

Table 5-30: Equipment Required for AC Power 115. . . . . . . . . . . .

Table 5-31: Procedure to Install Power Cables 115. . . . . . . . . . . . . .

Table 5-32: Power Cabinet AC Current Requirements 116. . . . . . .

Figures

Figure 5-1: SC 4812ET Intercabinet I/O Detail (Rear View) 85. . .

Figure 5-2: SC4812ET Conduit I/O Panel Detail 85. . . . . . . . . . .

Figure 5-3: Overall Cable Diagram 86. . . . . . . . . . . . . . . . . . . . . .

Figure 5-4: Antenna Panel Detail (Rear View) 90. . . . . . . . . . . . . .

Figure 5-5: 50 Pair Punch Block 91. . . . . . . . . . . . . . . . . . . . . . . .

Figure 5-6: Rubber I/O Boot Detail 93. . . . . . . . . . . . . . . . . . . . . .

Figure 5-7: SC 4812ET RF Cabinet 104. . . . . . . . . . . . . . . . . . . . . .

Figure 5-8: AC I/O Plate 107. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .