User Manual

List of Tables – continued
PRELIMINARY 2
SC 4812ET BTS Optimization/ATP – CDMA LMF
July 1999
x
Table 6-23: No DC Input Voltage to any C–CCP Shelf Module 5-20. . . . . . . . . . . .
Table 6-24: No DC Input Voltage to any C–CCP Shelf Module 5-20. . . . . . . . . . . .
Table 5-25: Troubleshooting Control Link Failure 5-28. . . . . . . . . . . . . . . . . . . . . . .
Table 6-1: External Test Equipment Removal 6-1. . . . . . . . . . . . . . . . . . . . . . . . . .
Table 6-2: Procedures to Copy Files to a Diskette using the LMF 6-1. . . . . . . . . .
Table 6-3: Procedures to Copy CAL Files from Diskette to the CBSC 6-2. . . . . . .
Table 6-4: Procedures to Copy CAL Files from Diskette to the CBSC 6-3. . . . . . .
Table A-1: Verification of Test Equipment Used A-1. . . . . . . . . . . . . . . . . . . . . . . .
Table A-2: Site Checklist A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-3: Preliminary Operations A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-4: GPS Receiver Operation A-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-5: LFR Receiver Operation A-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-6: LPA IM Reduction A-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-7: TX BLO Calibration
(3–Sector: 1–Carrier, 2–Carrier and 4–Carrier Non–adjacent Channels) A-8. . . . .
Table A-8: TX Bay Level Offset Calibration
(3–Sector: 2–Carrier Adjacent Channels) A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-9: TX Bay Level Offset Calibration
(3–Sector: 3 or 4–Carrier Adjacent Channels) A-11. . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-10: TX BLO Calibration
(6–Sector: 1–Carrier, 2–Carrier Non–adjacent Channels) A-13. . . . . . . . . . . . . . . . .
Table A-11: TX Antenna VSWR A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-12: RX Antenna VSWR A-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A-13: AMR CDI Alarm Input Verification A-16. . . . . . . . . . . . . . . . . . . . . . . .
Table B-1: When RF Optimization Is required on the BTS B-1. . . . . . . . . . . . . . . .
Table B-2: When to Optimize Inter–frame Cabling B-2. . . . . . . . . . . . . . . . . . . . . .
Table B-3: SC 4812ET BTS Optimization and ATP Test Matrix B-4. . . . . . . . . . .
Table C-1: BBX2 Gain Set Point vs. Actual BTS Output (in dBm) C-1. . . . . . . . .
Table D-1: TX and RX Frequency vs. Channel D-3. . . . . . . . . . . . . . . . . . . . . . . . .
Table E-1: PnMaskI and PnMaskQ Values for PilotPn E-2. . . . . . . . . . . . . . . . . . .
Table E-2: I/Q PN initialization values for RF delay of 0, 13, & 14 Chips E-3. . .