User's Manual Part 1
List of Figures – continued
x 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU MAY 2004
PRELIMINARY
Figure 9-22: Filter Tray Connectors and Cable Part Numbers 9-61 . . . . . . . . . . . . . .
Figure 9-23: Filter Tray Connectors and Cable Part Numbers (SGLN6223) 9-62 . . .
Figure 9-24: Filter Tray Connectors and Cable Part Numbers (SGLN6222) 9-66 . . .
Figure 9-25: Compact Combined Linear Power Amplifier 9-69 . . . . . . . . . . . . . . . .
Figure 9-26: PDA Location 9-71 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9-27: Power Distribution Assembly for –48VDC 9-72 . . . . . . . . . . . . . . . . . .
Figure 9-28: Power Distribution Assembly for +27VDC 9-74 . . . . . . . . . . . . . . . . .
Figure 9-29:Heat Management System 9-76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9-30: HMS Heater Elements 9-79 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9-31: HMS Controller 9-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9-32: Blower Fan 9-82 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-1: TME and BTS Cable Routing 11-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-2: TX Output Fault Isolation Flowchart 11-35 . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-3: CSM Front Panel Indicators & Monitor Ports 11-51 . . . . . . . . . . . . . . . .
Figure 11-4: GLI3 Front Panel 11-54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-5: MCC24 and MCC–1X Front Panel LEDs and LED
Indications 11-56 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-6: MGLI/GLI Board MMI Connection Detail 11-58 . . . . . . . . . . . . . . . . . .
Figure B-1: Agilent E7495A Pre–Power Sensor Calibration Connection B-4 . . . . .
Figure B-2: Agilent E7495A Power Sensor Calibration Connection B-4 . . . . . . . . .
Figure B-3: Setting Agilent E4406A GPIB Address B-5 . . . . . . . . . . . . . . . . . . . . .
Figure B-4: Setting Agilent E4432B GPIB Address B-6 . . . . . . . . . . . . . . . . . . . . .
Figure B-5: Setting Advantest R3267 GPIB Address B-8 . . . . . . . . . . . . . . . . . . . .
Figure B-6: Advantest R3562 GPIB Address Switch Setting B-9 . . . . . . . . . . . . . .
Figure B-7: Agilent 8935 Test Set B-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-8: HP 8921A and HP 83236A/B B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-9: R3465 Communications Test Set B-12 . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-10: HP 437 Power Meter B-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-11: Gigatronics 8541C Power Meter Detail B-15 . . . . . . . . . . . . . . . . . . . .
Figure B-12: RS232 GPIB Interface Adapter B-16 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-13: HP 8921A/600 Cable Connections for 10 MHz Signal and
GPIB without Rubidium Reference B-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-14: HP 8921A Cable Connections for 10 MHz Signal and GPIB
with Rubidium Reference B-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-15: Cable Connections for Test Set without 10 MHz Rubidium
Reference B-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-16: Cable Connections for Test Set with 10 MHz Rubidium
Reference B-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure B-17: Agilent 8935/E4432B 10MHz Reference and Even Second
Tick Connections B-26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .