User's Manual Part 1

ManualsBrandsNokia Solutions and Networks ManualsElectronics1X SC480 BTS Microcell Base Station Transmitter

PRELIMINARY

68P09260A11–7

MAY 2004

ENGLISH

CDMA2000 1X

SOFTWARE RELEASE 2.16.4.X

Technical

Information

1X SC480 BTS HARDWARE

INSTALLATION, OPTIMIZATION/ATP, AND

FRU

800 MHZ

Summary of content (200 pages)

PAGE 1
Technical Information 1X SC480 BTS HARDWARE INSTALLATION, OPTIMIZATION/ATP, AND FRU SOFTWARE RELEASE 2.16.4.
PAGE 2
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Notice While reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. The information in this document has been carefully checked and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies or omissions. Motorola, Inc.
PAGE 3
Table of Contents 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU Software Release 2.16.4.X List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx FCC Requirements . . . . . . . . .
PAGE 4
Table of Contents – continued Span Line and RGPS Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Remote GPS Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Local GPS (RF–GPS) Antenna Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 Chapter 4: BTS and Cabling Installation Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
Table of Contents – continued Pinging the Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-33 Download the BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36 CSA System Time – GPS & HSO/MSO Verification . . . . . . . . . . . . . . . . . . . . 6-43 Test Equipment Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-51 Test Set Calibration . . . . . . .
PAGE 6
Table of Contents – continued RF Filter Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-55 Compact Combined Linear Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-67 TME Power Distribution Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-70 Heat Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-75 Thermal Management Enclosure . . . .
PAGE 7
Table of Contents – continued Appendix G: Integrated BTS Router Preliminary Operations Integrated BTS Router Preliminary Operations – Introduction . . . . . . . . . . . . . G-1 Verify GLI3 Software Version and Span Parameter Settings . . . . . . . . . . . . . . . G-2 Change GLI3 Span Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-6 Appendix H: Integrated BTS Router Installation Integrated BTS Router Installation – Introduction . . . . . . . . . . . . . . . . . . .
PAGE 8
List of Figures 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU Software Release 2.16.4.X vi Figure 1-1: Mounted BTS and Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Figure 1-2: CDMA Frequency Spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10 Figure 1-3: RS232–IEEE488 Converter Serial Cable Configuration . . . . . . . . . 1-16 Figure 1-4: Front View of Compact BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
List of Figures – continued MAY 2004 Figure 2-14: Mulitple Pole Installation and Functional Clearances for Enclosures and PA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26 Figure 2-15: Multiple Wall Installation and Functional Clearances for TME and HMS, PDE, and cCLPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27 Figure 3-1: Antenna Cabling Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
List of Figures – continued viii Figure 4-32: Typical Outdoor Grounding Configuration . . . . . . . . . . . . . . . . . 4-50 Figure 4-33: Typical Multiple Outdoor Grounding Configuration . . . . . . . . . . 4-51 Figure 4-34: Rear View of PDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-52 Figure 4-35: DC Power Terminal Strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54 Figure 4-36: TME Power Distribution Assembly for –48VDC . . . . . . . . . . .
PAGE 11
List of Figures – continued MAY 2004 Figure 6-14: TX Calibration Test Setup – CyberTest (IS–95A/B) and Agilent 8935 (IS–95A/B and CDMA2000 1X) . . . 6-58 Figure 6-15: TX Calibration Test Setup – Using Power Meter . . . . . . . . . . . . . 6-59 Figure 6-16: TX Calibration Test Setup – Agilent E4406A and Advantest R3567 (IS–95A/B and CDMA2000 1X) . . . . . 6-60 Figure 6-17: IS–95A/B ATP Test Set–up– CyberTest, Advantest R3465, and Agilent 8935 . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 12
List of Figures – continued x Figure 9-22: Filter Tray Connectors and Cable Part Numbers . . . . . . . . . . . . . . 9-61 Figure 9-23: Filter Tray Connectors and Cable Part Numbers (SGLN6223) . . . 9-62 Figure 9-24: Filter Tray Connectors and Cable Part Numbers (SGLN6222) . . . 9-66 Figure 9-25: Compact Combined Linear Power Amplifier . . . . . . . . . . . . . . . . 9-69 Figure 9-26: PDA Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 13
List of Figures – continued MAY 2004 Figure B-18: Agilent 10 MHz Reference Connections . . . . . . . . . . . . . . . . . . . B-26 Figure B-19: Advantest 10 MHz Reference and Serial I/O Connections . . . . . . B-27 Figure B-20: Performing Agilent E4406A Self–alignment (Calibration) . . . . . B-28 Figure B-21: Power Meter Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-29 Figure B-22: Gigatronics 8541C Power Meter Detail . . . . . . . . . . . . . . . . . . . .
PAGE 14
List of Tables 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU Software Release 2.16.4.X xii FCC Part 68 Registered Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxv Table 1-1: Abbreviations and Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Table 1-2: Regular Band Class 0 TX and RX Frequency vs Channel . . . . . . . . 1-9 Table 1-3: China A–Band TX and RX Frequency vs Channel . . . . . . . . . . . . . .
PAGE 15
List of Tables – continued MAY 2004 Table 4-2: Procedure to Attach BTS Mounting Bracket . . . . . . . . . . . . . . . . . . 4-7 Table 4-3: Procedure to Attach BTS to Mounting Plate . . . . . . . . . . . . . . . . . . . 4-8 Table 4-4: DC Input Cable Description and Part Number . . . . . . . . . . . . . . . . . 4-10 Table 4-5: Procedure to Mount the Power Amplifier . . . . . . . . . . . . . . . . . . . . . 4-11 Table 4-6: Ground Cable and Lug Description and Part Number . . . . . . . . . . .
PAGE 16
List of Tables xiv – continued Table 4-39: Customer Input Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . 4-74 Table 4-40: Customer Input Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . 4-75 Table 4-41: Procedure for Using Ferrite Core on Customer Input and Output Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-75 Table 4-42: Indoor Installation Completion Checklist . . . . . . . . . . . . . . .
PAGE 17
List of Tables – continued MAY 2004 Table 6-18: Enable MCCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-42 Table 6-19: Test Equipment Setup (GPS & HSO/MSO Verification) . . . . . . . . 6-45 Table 6-20: GPS Initialization/Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-47 Table 6-21: IS–95A/B–only Test Equipment Interconnection . . . . . . . . . . . . . . 6-53 Table 6-22: CDMA2000 1X/IS–95A/B Test Equipment Interconnection . . . . .
PAGE 18
List of Tables xvi – continued Table 8-5: Terminate the WinLMF Session and Remove the WinLMF . . . . . . . 8-4 Table 8-6: Connect T1 or E1 Spans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Table 8-7: Check Before Leaving the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Table 8-8: Reset BTS Devices and Remote Site Initialization . . . . . . . . . . . . . . 8-5 Table 9-1: Procedure to Remove Fan Module . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 19
List of Tables – continued MAY 2004 Table 9-34: Procedure to Install Filter Tray Kit SGLF4152 . . . . . . . . . . . . . . . . 9-58 Table 9-35: Procedure to Remove Filter Tray Kit SGLN6223 . . . . . . . . . . . . . . 9-61 Table 9-36: Procedure to Install Filter Tray Kit SGLN6223 . . . . . . . . . . . . . . . 9-63 Table 9-37: Procedure to Remove Filter Tray Kit SGLN6222 . . . . . . . . . . . . . . 9-65 Table 9-38: Procedure to Install Filter Tray Kit SGLN6222 . . . . . . . . . . . . . . .
PAGE 20
List of Tables xviii – continued Table 9-71: TME HMS Controller Item Number List . . . . . . . . . . . . . . . . . . . . 9-91 Table 9-72: TME HMS Blower Fan Item Number List . . . . . . . . . . . . . . . . . . . 9-91 Table 10-1: Login and Access Alarm Window Procedure . . . . . . . . . . . . . . . . . 10-2 Table 10-2: Shut Down Site Signaling Functions Procedure For a Circuit BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 21
List of Tables – continued MAY 2004 Table 11-14: Login Failure Troubleshooting Procedures . . . . . . . . . . . . . . . . . . 11-21 Table 11-15: Force Ethernet LAN A to Active State as Primary LAN . . . . . . . 11-22 Table 11-16: GLI IP Address Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-23 Table 11-17: Troubleshooting a Power Meter Communication Failure . . . . . . . 11-25 Table 11-18: Troubleshooting a Communications System Analyzer Communication Failure . . . .
PAGE 22
List of Tables xx – continued Table A-3: Procedure to Test MCC–DO Pilot Time Offset . . . . . . . . . . . . . . . . A-6 Table A-4: Procedure to Test MCC–DO Rho . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8 Table A-5: Procedure to Test MCC–DO Packet Error Rate . . . . . . . . . . . . . . . . A-10 Table B-1: Set IP Address on Agilent E7495A test set . . . . . . . . . . . . . . . . . . . B-2 Table B-2: Detecting Agilent E7495A Test Equipment . . . . . . . . . . . . . . . . . . .
PAGE 23
List of Tables – continued MAY 2004 Table E-3: Starter and Three Expansion BTS Interconnect Cabling for Circuit or Packet Configuration with Dual cCLPA . . . . . . . . . . . . . . . . . . . E-3 Table E-4: Starter and Two Expansion BTS Interconnect Cabling for Circuit or Packet Configuration with Dual cCLPA . . . . . . . . . . . . . . . . . . . E-5 Table E-5: Starter and One Expansion BTS Interconnect Cabling for Circuit or Packet Configuration with Dual cCLPA . . . . . . . . . . . . . . . . . . .
PAGE 24
Foreword Scope of manual This manual is intended for use by cellular telephone system craftspersons in the day-to-day operation of Motorola cellular system equipment and ancillary devices. This manual is not intended to replace the system and equipment training offered by Motorola, although it can be used to supplement or enhance the knowledge gained through such training.
PAGE 25
Foreword – continued The following typographical conventions are used for the presentation of software information: S In text, sans serif BOLDFACE CAPITAL characters (a type style without angular strokes: for example, SERIF versus SANS SERIF) are used to name a command. S In text, typewriter style characters represent prompts and the system output as displayed on an operator terminal or printer.
PAGE 26
FCC Requirements Content This section presents the Federal Communications Commission (FCC) Rules Parts 15 and 68 requirements and compliance information for the SC480 domestic series Radio Frequency Base TransceiverStations. FCC Part 15 Requirements Part 15.19a(3) – Information to User NOTE This device complies with Part 15 of the FCC Rules. Operationis subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
PAGE 27
FCC Requriements – continued Part 15.105(b) – Information to User NOTE This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radiocommunications.
PAGE 28
FCC Requirements – continued If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
PAGE 29
General Safety Remember! . . . Safety depends on you!! The following general safety precautions must be observed during all phases of operation, service, and repair of the equipment described in this manual. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the equipment. Motorola, Inc. assumes no liability for the customer’s failure to comply with these requirements.
PAGE 30
General Safety – continued Do not service or adjust alone Do not attempt internal service or adjustment, unless another person, capable of rendering first aid and resuscitation, is present. Do not substitute parts or modify equipment Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification of equipment. Contact Motorola Warranty and Repair for service and repair to ensure that safety features are maintained.
PAGE 31
Revision History Manual Number 68P09260A11–7 Manual Title 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU Software Release 2.16.4.X Version Information The following table lists the manual version, date of version, and remarks on the version. Version Level Date of Issue –1 Feb 4, 2004 DRAFT – For General engineering review –2 Feb 23, 2004 PRELIMINARY – Incorporated Engineering review comments.
PAGE 32
Revision History – continued Notes xxx 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 33
1 Chapter 1: Introduction Table of Contents MAY 2004 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope of this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site Cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site Manager . . . . . . . . . . .
PAGE 34
1 Table of Contents – continued Indoor Installation Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outdoor Installation Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATP Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 35
Introduction 1 Scope of this Document This document provides information pertaining to the hardware installation, cabling installation, ATP and Field Replaceable Unit (FRU) procedures of the Motorola SCt480 CDMA Base Transceiver Subsystem (BTS), 800 MHz, –48 and +27 VDC versions. Information on Circuit and Packet Backhaul, Expansion, and Logical BTS are also included The FRU procedures cover all components that are considered replaceable.
PAGE 36
1 Introduction – continued Chapter 7 “Acceptance Test Procedures” – This chapter contains general information and procedures for testing the BTS. Chapter 8 “Leaving the Site” – This chapter contains general information and procedures for preparing to leave and departing the site. Chapter 9 “Field Replaceable Units” – This chapter contains general information and procedures for removing and installing boards, cards and modules of the BTS.
PAGE 37
Introduction – continued 1 Appendix H “Integrated BTS Router Installation ” – This appendix contains general information and procedures IBR and span line installation. Appendix I “Packet Backhaul BTS ” – This appendix contains general information and procedures for packet backhaul operation with LMF Help.
PAGE 38
1 Introduction – continued Figure 1-1: Mounted BTS and Rack NOTE: SIngle BTS setup shown.
PAGE 39
Required Documents 1 Installation The following documents are required to perform the installation, ATP and FRU procedures of the cell site equipment: S SCt480 BTS Hardware Installation, Optimization/ATP and FRU – 68P09260A11 (This manual) S Standards and Guidelines for Communication Sites – Hard copy (Motorola Part Number 6881089E50–A) – CD–ROM (Motorola Part Number 9882904Y01) S Grounding Guidelines for Cellular Radio Installations (Motorola part number 68P81150E62) or – Appendix C of Standards and
PAGE 40
1 Required Documents – continued Table 1-1: Abbreviations and Acronyms Acronym Description CAL Calibration CBIO Compact BTS Input/Output CBSC Centralized Base Station Controller cCLPA Compact Combined Linear Power Amplifier CCP2 CDMA Channel Processor 2 CDF Configuration Data File CDMA Code Division Multiple Access cMPC Compact Multi–coupler Preselector Card CRMS Cellular Remote Monitoring System CSA Clock Synchronization Alarms DLM Download Manager EMPC Expansion Compact Mulit–P
PAGE 41
Required Documents – continued 1 Table 1-1: Abbreviations and Acronyms Acronym MAY 2004 Description LMT Local Maintenance Tool MCC Multi–Channel CDMA MCC–DO Multi–Channel CDMA Data Only MMI Man–Machine Interface MON Monitor MSO Medium Stability Oscillator NECB Network Element Configuration Base NECF Network Element Configuration File NECJ Network Element Change Journal OMC–R Operations and Maintenance Center – Radio OOS Out–of–Service PDE Power Distribution Enclosure PSM Power
PAGE 42
1 800 MHz CDMA Frequencies and Channels 800 MHz Center Frequencies Table 1-2 lists the selected 800 MHz CDMA candidate operating channels and the corresponding transmit and receive frequencies for Regular Band Class 0 (North America). Figure 1-2 shows the CDMA Frequency Spectrum for Table 1-2. Center frequencies (in MHz) for channels not shown in the table may be calculated as follows: For Channels 1 – 799 S For TX TX = 870 + (0.03 * Channel #) Example: Channel 262 TX = 870 +0.03 * 262 TX = 877.
PAGE 43
800 MHz CDMA Frequencies and Channels – continued 1 CAUTION Certain widely–spaced combinations of A–Band transmit frequencies, when combined to drive one antenna, can produce 3rd order intermodulation products that are within the receive band. During system planning, the proper selection of combined frequencies or the use of multiple transmit antennas will prevent this situation. Additional receive filtering at a particular cell site can also help.
PAGE 44
800 MHz CDMA Frequencies and Channels – continued Figure 1-2: CDMA Frequency Spectrum TX FREQUENCY INCREASE 1 1-10 (MHz) RX CHANNELS 824.700 824.880 824.910 825.000 825.030 869.700 869.880 869.910 870.000 870.030 1013 1019 1020 1023 1 825.110 870.110 37 CHINA A–BAND 833.490 878.490 283 834.090 834.120 303 304 834.330 879.090 879.120 897.330 835.680 880.680 356 835.860 835.890 880.860 880.890 362 363 844.110 844.140 889.110 889.140 637 638 844.320 889.320 644 845.670 890.
PAGE 45
Installation Tools and Materials 1 Introduction Many of the tools and materials depend on the style of the wall, pole, or rack on which the mounting bracket is being installed. The tools and materials required to install the BTS hardware are specified for each mounting style. Due to the variability of mounting styles, additional tools and materials may be required to meet specific site needs.
PAGE 46
1 Installation Tools and Materials – continued Table 1-4: Recommended Tools and Materials for Rack Mounting Hand Tools Small Phillips Screwdriver Materials Purpose Customer Supplied General purpose use Hex Crimping Tool Various die sets (Customer Supplied) Create RF cabling and power/ground cabling RJ45 Crimping Tool (Tyco P/N 2–231652–1, 853400–0, 853400–1, 853400–7 or equivalent) Customer Supplied Create RJ11/RJ45 cabling 5/16 Breakaway Torque Wrench, 9–in.
PAGE 47
Installation Tools and Materials – continued 1 Table 1-4: Recommended Tools and Materials for Rack Mounting Hand Tools Materials Purpose 6 AWG stranded (Customer Supplied) Ground cabling Assorted ground lugs (6AWG, 10 AWG) ring style (Customer Supplied) Site ground cabling, Core power input Assortment of flat washers, lock washers (Customer Supplied) Mounting equipment to racks and for general purpose Assortment of nuts M3 – M6 (Customer Supplied) Mounting equipment to racks and for general purp
PAGE 48
1 ATP Tools and Materials Policy To ensure consistent, reliable, and repeatable test results, test equipment meeting the following technical criteria should be used to perform the ATP on the BTS equipment. NOTE During manual testing, you can substitute supported test equipment with other test equipment models not supported by the LMF. However, they must meet the same technical specifications.
PAGE 49
ATP Tools and Materials – continued 1 Test Equipment List The following pieces of test equipment are required during the ATP. Common assorted tools like screwdrivers and keys are not listed, but are still required. Read the owners manual on all of the following major pieces of test equipment to understand their individual operation prior to use in optimization. NOTE Always refer to specific OEM test equipment documentation for detailed operating instructions.
PAGE 50
1 ATP Tools and Materials – continued CDMA LMF Software The Local maintenance Facility (LMF) application program is a graphical user interface (GUI)–based software tool.
PAGE 51
ATP Tools and Materials – continued 1 S Advantest R3465 Analyzer with R3561L signal generator CDMA2000 1X and IS–95A/B test capability – The following communications system analyzers which provide both CDMA2000 1X and IS–95A/B test capability are supported by the LMF: S Agilent 8935 series E6380A communications test set (formerly HP 8935) with option 200 or R2K for CDMA2000 1X support S Agilent E4406A S Advantest R3267 spectrum analyzer with Advantest R3562 Generator for IS–95 and cdma200 1X testing A c
PAGE 52
1 ATP Tools and Materials – continued Model SLN2006A MMI Interface Kit S Motorola Model TRN9666A null modem board. Connectors on opposite sides of the board must be used as this performs a null modem transformation between cables. This board can be used for 10–pin to 8–pin, 25–pin to 25–pin and 10–pin to 10–pin conversions. S Motorola 30–09786R01 MMI cable or equivalent; used to interface the LMF serial port connection to GLI, CSA and cCLPA debug serial ports.
PAGE 53
ATP Tools and Materials – continued 1 Directional Coupler S 30 dB attenuation Optional Equipment NOTE Not all optional equipment specified here will be supported by the LMF in automated tests or when executing various measure type commands. It is meant to serve as a list of additional equipment that might be required during maintenance and troubleshooting operations.
PAGE 54
1 BTS Equipment Identification Overview Stand–Alone BTS The 1X SC480 BTS consists of one shelf of cards and modules within a metal cabinet. Depending on configuration the BTS may be powered by: S Converted AC to –48 VDC S Converted AC to +27 VDC S Battery (–48 or +27 VDC) S +27 VDC S –48 VDC The BTS can support up to two carriers in a non–redundant omni configuration. Figure 1-4 shows the two different front vies and Figure 1-5 shows the rear view of the BTS.
PAGE 55
BTS Equipment Identification – continued 1 CCP2 Shelf Card/Module Device ID Numbers Logical BTS All cards/modules/boards in the BTSes at a single site, assigned to a single BTS number, are also identified with unique Device ID numbers dependent upon the Frame ID number in which they are located. Refer to Table 1-5 for specific device ID numbers. See Figure 1-6 for shelf layout.
PAGE 56
1 BTS Equipment Identification – continued Figure 1-4: Front View of Compact BTS Front Panel Cover Standard CCP2 Shelf Front Panel cover removed CCP2 Shelf with MCC–DO card Front Panel cover removed 1-22 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 57
BTS Equipment Identification – continued 1 Figure 1-5: Rear View of Compact BTS RF GPS not shown and SDCX Module is shown.
PAGE 58
1 BTS Equipment Identification – continued Shelf Device ID Numbers for Stand–Alone All cards/modules/boards in the BTS at a single site assigned to a single BTS are also identified with unique Device ID numbers. Refer to Table 1-6 for the Device ID Numbers. Reference Figure 1-6 or Figure 9-2 for the layout of the shelf. Table 1-6: Shelf Device ID Numbers BTS # PS1 CSA GLI 1 1 1 1 MCC 1 2 BBX 3 1 cMPC 4 – Figure 1-6: CCP2 Shelf Layout SYNC MONITOR STA/ALM FREQ.
PAGE 59
BTS Equipment Identification – continued 3. 4. 5. 6. 7. 8. 9. 1 GLI3 MCC–1X (or MCC–DO) MCC–1X (or MCC–DO) MCC–1X or Filler Panel BBX–1X (Carrier 1) BBX–1X (Carrier 2) cMPC Power Supply Module Occupies the first slot. The same assembly used in the SC48XX series. Provides power to the cards on the CCP2 shelf. CSA Card Occupies the second slot. The Clock Synchronization Alarm card, combines the functions of the SC4812’s CSM and AMR cards into one.
PAGE 60
1 BTS Equipment Identification – continued HSO and MSO The High Stability and Medium Stability Oscillator module provide a backup reference source should the Global Positioning System (GPS) fail. The HSO is capable of providing up to 24 hours and the MSO is capable of providing up to 8 hours. Only one of either the HSO or MSO is available in the Compact BTS. The module is located in front, behind a cover, underneath the CCP2 Shelf. The unit slides into the top slot of the two that are present.
PAGE 61
BTS Equipment Identification – continued 1 Figure 1-7: CBIO Board TME Alarm LAN RF–GPS PWR Expansion TX RF–GPD IN PDE Alarm Customer Input/Output CBIO LEDs Network Span 1X–A, –B, & –C Expansion RX Main Group 1 Span DO–A, –B, & –C EXPANSION FRAME SYNC – OUT Expansion RX Diversity DAISY–CHAIN POWER SDCX SDCX POWER cCLPA Data A & B SDCX KIT NO. SDCX SERIAL NO.
PAGE 62
BTS Equipment Identification – continued RF Connectors Figure 1-8 shows the RF connectors at the rear of the Compact BTS. Modem Connector Figure 1-8 shows the Modem connector at the rear of the Compact BTS (not supported in SC480). Circuit Breaker Figure 1-8 and Figure 1-9 show the location of the –48VDC 20A circuit breaker and +27VDC 25A circuit breaker, respectively. DC Power Connection Figure 1-8 and Figure 1-9 shows the location of the DC Power Terminal Strip.
PAGE 63
BTS Equipment Identification – continued 1 Figure 1-9: +27VDC RF Connectors, Circuit Breaker, DC Power Terminal Strip, and Ground Studs 25A Circuit Breaker 25 TME 25A GROUND (Screw Holes) MAY 2004 DC Power Terminal Strip +27 V RETURN TME 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY 1-29
PAGE 64
1 Outdoor Enclosure Equipment Identification Outdoor Enclosure Equipment Identification Figure 1-10 shows the TME and HMS outdoor enclosures. Figure 1-10: Thermal Managment Enclosure and Heat Manaagement System Wall Mounting Bracket Heat Management System Thermal Management Enclosure Compact BTS Thermal Management Enclosure The following are brief descriptions of the components of the TME. TME The Thermal Management Enclosure surrounds the Compact BTS, affording it protection against the weather.
PAGE 65
BTS Equipment Identification – continued 1 Figure 1-11: Power Distribution Assembly (–48V version shown) ti–cdma–wp–00350–v01–ildoc–ah Power Distribution Enclosure The following are brief descriptions of the components of the PDE. PDE The Power Distribution Enclosure converts AC voltage to DC voltage for use by the TME and Compact Combined Linear Power Amplifier (cCLPA). Battery backup is routed through the PDE. See Figure 1-12. S AC Load Center (ACLC) – Where the AC voltage is connected to the PDE.
PAGE 66
1 Outdoor Enclosure Equipment Identification – continued Figure 1-12: Power Distribution Enclosure and Heat Exchanger Power Management Enclosure Heat Exchanger Antenna Surge Arrestor Location Ground Location Combined Compact Linear Power Amplifier Figure 1-13: Compact Combined Linear Power Amplifier ti–cdma–wp–00300–v01–ildoc–ah 1-32 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 67
Installation and ATP Order 1 Indoor Installation Order The pieces of the BTS should be installed in the following order. 1. Unpack and inspect hardware 2. Install mounting hardware and bracket (s) 3. Attach and secure unit to mounting bracket 4. Install GPS 5. Prepare site cabling 6. Attach all ground cabling to unit(s) 7. Attach all cables to unit(s) Outdoor Installation Order The pieces of the BTS should be installed in the following order. 1. Unpack and inspect hardware 2.
PAGE 68
1 Installation and ATP Order – continued 11. 12. 13. 14. 15. 16. 17. 18. 19.
PAGE 69
Chapter 2: Site Preparation Table of Contents MAY 2004 Site Preparation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Verifications and procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site manager . . . . . . . . . . . . . .
PAGE 70
Table of Contents 2 – continued TME Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PDE Dimensions and Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PDE Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outdoor Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 71
Site Preparation Overview Overview This chapter provides the procedures and information to verify that the site is ready to have the equipment installed. It also provides procedures to ensure the safety of the installation personnel, protect the equipment from damage, and verify the site layout parameters. Installation This SCt480 BTS can be installed indoors. The site preparation depends on the type of installation and the site characteristics. Battery back up is optional and provided by the customer.
PAGE 72
Site Inspections Inspection overview Inspect the site to verify that the necessary equipment has been properly installed. Also, as part of the inspection, verify that the equipment is adequate to support the Motorola equipment. Not all inspections may apply to every site. The site characteristics determine which inspections apply. 2 NOTE Installation of ancillary equipment (e.g., power supplies, terminal blocks, etc.) may be the responsibility of the installer.
PAGE 73
Site Inspections – continued Cabling rack Inspect the cable rack for proper installation. The cable racks should be at least 7 ft from the floor. The cable racks should be electrically tied together with 6 AWG wire, except cable racks that are in an isolated ground zone. Fire protection For indoor installations verify with the site manager that some type of fixed fire suppression equipment is installed.
PAGE 74
Site Inspections – continued Grounding Inspections Indoor installations 2 For indoor installations refer to the Grounding Guideline for Cellular Radio Installations (68P81150E62) for all grounding inspection procedures. Verify the following: S All ground cables have a bend radius of 20 cm (8 inches) or more. S Metallic lines (span, phone[modem], RGPS, power and antenna) that enter or leave the site should be equipped with a 3-electrode gas tube protector.
PAGE 75
Prepare Site for the Arrival of the Equipment Description This information covers various topics not all of which are needed at every site. Based on the site characteristics execute the steps that apply to your site. Before installing the equipment, do the following to ensure the safety of installation personnel and to protect the equipment.
PAGE 76
Prepare Site for the Arrival of the Equipment – continued Procedure to Prepare the Site for the Equipment 2 Table 2-1: Procedure to Prepare the Site for the BTS Step Action 1 If some type of protective padding is available install it around any existing equipment at the site that could be damaged during installation of the unit(s). 2 Hang plastic sheets around intended work areas to prevent dust and debris from damaging co-located equipment during installation.
PAGE 77
Unpacking the Equipment Description The Purpose of this section is to describe how the SC480 Compact BTS, TME, PDE, and cCLPA are packaged for shipping and how to correctly unpack the units in preparation for installation. How Equipment is Shipped The equipment are shipped in either cardboard or wood containers. The equipment are shipped with all internal cabling installed. For an indoor installation, the BTS is shipped in a single container. BTS accessories are shipped in their own container.
PAGE 78
Unpacking the Equipment – continued Table 2-2: Recommended Unpacking Tools Qty 2 Description 1 Tin Snips 2 Knife, Box Cutter, or Scissors Unpacking Diagrams The following diagrams show how to unpack the equipment. WARNING The steel bands surrounding the container can spring out from the container when the bands are cut. To avoid personal injury, stand safely to one side of the bands while cutting.
PAGE 79
Unpacking the Equipment – continued Figure 2-2: Wood Shipping Container Wood Crate Top 2 NOTE: 1. Normally this styrofoam packing is attached to the pallet. it is shown exploded for clarity 2. This example shows the TME shipping container.
PAGE 80
Unpacking the Equipment – continued Figure 2-3: Cardboard Shipping Container 2 Wall Mounting Bracket cardboard Box Cardboard Lid Insert with Packing Styrofoam Packing NOTE: 1. Normally this styrofoam packing is attached to the pallet. it is shown exploded for clarity 2. This example shows the TME shipping container.
PAGE 81
Unpacking the Equipment – continued Unpacking a Cardboard or Wood Container Follow the procedure in Table 2-3 to unpack equipment from a container. Table 2-3: Unpacking Equipment from a Cardboard or Wood Container Step 1 Action Inspect the container for damage. Cardboard Container 2 Open container using tin snips to cut each outer steel band or a knife (or equivalent) to cut the plastic wrap that surrounds the container. 3 Remove equipment door key from top of container.
PAGE 82
Unpacking the Equipment – continued Table 2-4: Procedure to Remove Outdoor Equipment from Container Step 2 Action n WARNING The TME and HMS are shipped as one unit. Together they weigh 39 kg (86 lbs). It is recommended that the HMS be removed first; otherwise, two people are required to remove the TME with HMS installed. 6 Use the key to unlock the HMS and open. 7 Use a wrench to remove two nuts and washers securing ground cable to HMS. 8 Disconnect signal cable from TME.
PAGE 83
Unpacking the Equipment – continued Removing Indoor Equipment from a Container Follow the procedure in Table 2-5 to remove the indoor equipment from a container. The following procedure starts with the BTS removal and continues through to the Mounting Plate. The order of opening containers is not important, it is just for demonstration purposes. The procedure is written for one set. Perform procedure as many times as required to accommodate the site configuration.
PAGE 84
Dimensions and Clearances BTS Overview 2 This information covers the dimensions and clearances associated with the BTS for indoor configurations. Dimensions and Clearances Table 2-6, Table 2-7, and Figure 2-4 through Figure 2-7 show the installed dimensions and recommended clearances for each item. Table 2-6: Installation Dimensions for the BTS Item Height Width Depth Weight BTS (fully installed) 425 mm (17 in.) 218 mm (9 in.) 626 mm (25 in.
PAGE 85
Dimensions and Clearances – continued BTS Dimensions The BTS dimensions are shown below.
PAGE 86
Dimensions and Clearances – continued cCLPA Dimensions and Clearances Table 2-8, Table 2-9, and Figure 2-5 show the installed dimensions and recommended clearances for each item. 2 Table 2-8: Installation Dimensions for the cCLPA Item Height Length Width Weight cCLPA 261 mm (10 in.) 495 mm (19 in.) 295 mm (12 in.) 20 kg (44 lbs) Table 2-9: Minimum Clearances for the cCLPA Item Front Back Left Right Top Bottom Installation and Maintenance Requirements 680 mm (27 in.) 0 mm (0 in.
PAGE 87
Dimensions and Clearances – continued Figure 2-5: cCLPA Dimensions and Functional Clearances Top Clearance 100 mm minimum NOTE: Overall length of cCLPA is from mounting flange to mounting flange. 2 487.0 mm Side Clearance 150 mm minimum Side Clearance 150 mm minimum 295.0 mm Bottom Clearance 500 mm minimum Bottom Clearance 1 M minimum above ground Front Clearance 680 mm minimum 260.
PAGE 88
Dimensions and Clearances – continued Unit Clearances The unit clearances are shown below. 2 Figure 2-6: Indoor Functional Clearances for BTS Side Clearance 50 mm minimum Mounting Plate Front Clearance 50 mm minimum NOTE: For access to RF filter tray, remove BTS from the shelf. Top View Rear Clearance 50 mm minimum Compact BTS Side Clearance 50 mm minimum NOTE: If there is only one cCLPA, then the top clearance is 100 mm (4 in.) minimum. The clearance above a single BTS is 125 mm (5 in.
PAGE 89
Dimensions and Clearances – continued Figure 2-7: Indoor Functional Clearances for BTS Side–By–Side Configuration NOTE: For access to RF filter tray remove BTS from the shelf. Seated side–by–side on the mounting plate does not interfere with BTS ventilation. 2 Side Clearance 50 mm minimum Front Clearance 50 mm minimum Top View Rear Clearance 50 mm minimum Side Clearance 50 mm minimum NOTE: The 100 mm (4 in.) clearance above the cCLPA only applies if there is a single cCLPA present.
PAGE 90
Dimensions and Clearances – continued TME Dimensions and Clearances Table 2-10, Table 2-11, Figure 2-9, and Figure 2-10 show the TME installed dimensions and recommended clearances. 2 Table 2-10: Installation Dimensions for the TME Item Height Length Width Weight TME 530 mm (21 in.) 738 mm (29 in.) 448 mm (18 in.) 34 kg (75 lbs) Table 2-11: Minimum Clearances for the TME Item Front Back Left Right Top Bottom Installation and Maintenance Requirements 705 mm (30 in.) 51 mm (2 in.
PAGE 91
Dimensions and Clearances – continued Figure 2-9: Overall Dimensions of the Thermal Management Enclosure 738 mm 2 530 mm ti–cdma–wp–00354–v01–ildoc–ah 448 mm ti–cdma–wp–00353–v01–ildoc–ah MAY 2004 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY 2-21
PAGE 92
Dimensions and Clearances – continued TME Clearances Figure 2-10 shows the recommended clearances for the TME.
PAGE 93
Dimensions and Clearances – continued PDE Dimensions and Clearances Table 2-12, Table 2-13, and Figure 2-11 and Figure 2-12 show the installed dimensions and recommended clearances for each item. 2 Table 2-12: Installation Dimensions for the PDE Item Height Length Width Weight PDE *350 mm (14 in.) 810 mm (32 in.) 473 mm (19 in.) 52 kg (115 lbs) * Mounting Bracket extends an additional 186 mm (7 in) beyond bottom of TME.
PAGE 94
Dimensions and Clearances – continued Figure 2-12: PDE Overall Dimensions 810 mm 2 760 mm 350 mm 186 mm 473 mm 444 mm 305mm ti–cdma–wp–00270–v01–ildoc–ah 2-24 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 95
Dimensions and Clearances – continued PDE Clearances Figure 2-13 shows the recommended clearances for the PDE. 2 Figure 2-13: Functional Clearances for PDE Rear Clearance 51 mm Side Clearance 150 mm Side Clearance 150 mm Front Clearance 300 mm Top Clearance 150 mm Bottom Clearance 1M Outdoor Clearances Figure 2-14 and Figure 2-15 show the minimum clearances for the outdoor configuration.
PAGE 96
Dimensions and Clearances – continued Figure 2-14: Mulitple Pole Installation and Functional Clearances for Enclosures and PA 2 BTS with TME/HMS, PDE HX, & PA Electrical connections not shown PA 2 TME 2&4, PDE 2, and PA2 are attached on the opposite side of the pole.
PAGE 97
Dimensions and Clearances – continued Figure 2-15: Multiple Wall Installation and Functional Clearances for TME and HMS, PDE, and cCLPA 2 PA #2 PA #1 A possible layout is shown. Electrical connections not shown 10 Meters Battery Backup not shown. Batteries are connected through the PDE.
PAGE 98
Dimensions and Clearances – continued Notes 2 2-28 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 99
Chapter 3: BTS Cables Table of Contents 3 MAY 2004 Cable Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configurations Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cabling Installation Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable Labels . . . . . . . . . . . . . . . . . .
PAGE 100
Table of Contents – continued Notes 3 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 101
Cable Description Overview This chapter provides the procedures to install the BTS site cabling, but not attach it to the BTS . Connect the cables to the site and route them to the BTS location. Procedures for attaching the cables to the BTS is contained in Chapter 4. NOTE 3 Cabling is one of the most noticeable aspects of workmanship. Straight runs and proper turns are critical for a positive evaluation of the work.
PAGE 102
Cable Description – continued Customer I/O Connector The recommended connector for Customer Input and Output is listed below: S Input Connector: Molex, terminla plugs, P/N 39352–0106 S Output Connector: Molex, terminla plugs, P/N 39352–0108 3 Cable Descriptions and Part Numbers Table 3-1 gives the cable descriptions and part numbers for the cables used to install the BTS. Table 3-1: Cable Descriptions and Part Numbers Cable Qty.
PAGE 103
Cable Description – continued Table 3-1: Cable Descriptions and Part Numbers Cable Qty. Part Number Description K 1 Customer Supplied AC power cable, 10 AWG, copper, designed for 200 – 240 VAC @ 25 A. L{ 2–7 Customer Supplied DC power cables, 8–10 AWG, stranded, designed for –60 to –40 VDC power input *Quantity of cables depends upon system configuration. Your system may require one or more Motorola kits.
PAGE 104
Power, Earth Ground, and Battery Cabling Objective The objective of this procedure is to install the power and earth ground cabling for the BTS at the site. WARNING Dangerous voltages, capable of causing death, are present in this equipment. Use extreme caution when handling and testing this equipment. 3 Grounding Considerations This procedure covers only the grounding information for the cable that attaches to the BTS.
PAGE 105
Power, Earth Ground, and Battery Cabling – continued Indoor Power Considerations The BTS is designed for –60 to –40 VDC power input. The power for the Indoor BTS configuration is: S DC power Outdoor Power Considerations 3 The TME/BTS and cCLPA are designed for –60 to –40 VDC power input from the PDE. The PDE is designed for 200–240 VAC input.
PAGE 106
Antenna Cabling Cable Labels The cable designations are referenced to Table 3-1 in the “Cable Description” area of this chapter. Required Cables Table 3-2 provides the quantities and descriptions of the cables. 3 Table 3-2: Cables Needed for Antenna Connections Cable Qty. Part Number Description B 1 to 4* Andrew LDF4–50 Customer Supplied Antenna Cable, 800 MHz, 10 m (31 ft.) * Four cables are required if a cCLPA is used, otherwise, two are needed for the BTS only.
PAGE 107
Span Line and RGPS Cabling Cable Labels The cable designations are referenced to Table 3-1 in the “Cable Description” area of this chapter. Required Tools and Materials Table 3-4 provides the quantities and descriptions of the cables. 3 Table 3-4: Cables Needed for Span/RGPS Connections Cable Qty. Part Number Description C 1 T472AA RGPS cable, 15 m (50 ft.) T472AB RGPS cable, 38 m (125 ft.) T472AC RGPS cable, 76 m (250 ft.) T472AD RGPS cable, 152 m (500 ft.
PAGE 108
Span Line and RGPS Cabling – continued Table 3-5: Pin/Signal Information for Span Cable BTS Interface 3 Span Line Cable Pin Wire/Stripe Color Description 1 White/Orange 2 Orange 3 White/Green 4 Blue 5 White/Blue 6 Green NC 7 White/Brown NC 8 Brown NC RX RING RX TIP NC TX RING TX TIP Cable Pin and Signal Information for RGPS Cabling Table 3-6 gives the pin and signal information for the RGPS cable. Connector must be a 15 pin, D–Sub, female.
PAGE 109
Remote GPS Head Objective The objective of this procedure is to show how to install the Remote Global Positioning System (RGPS) head. Required Tools and Materials One RGPS Head (Motorola Part Number 0186012H03 or 0186012H04) is required to do this procedure. RGPS Mounting Considerations The RGPS Head requires specific mounting considerations in order to properly observe the GPS satellites. S The mounting pipe for the RGPS head should be mounted vertically with less than five degrees (5_) of tilt.
PAGE 110
Remote GPS Head – continued S The RGPS head is rated for ambient air temperatures from –40°C (–40°F) to 80°C (176°F), and has ratings for humidity, shock, waterproof, UV light resistance, vibrations, salt fog, ESD, EMI, and altitude. S The RGPS system used for the SCt480 BTS will support up to 604 m (2000 ft.) of overall cable length from the RGPS head to the last connected BTS. If a long cable run needs to be broken into pieces, minimize the number of breaks in the cable.
PAGE 111
Local GPS (RF–GPS) Antenna Cabling Objective The objective of this procedure is to install the Radio Frequency Global Positioning System receiver (RF–GPS) antenna cabling. More commonly referred to as Local GPS. Cable labels The cable designations referenced to Table 3-1 in the “Overall Cabling and Descriptions” area. Cabling diagram Figure 4-48 shows the Local GPS antenna connections. Equipment needed Table 3-7 contains a detailed description of the Local GPS Cabling. Table 1-4 lists the tools needed.
PAGE 112
Local GPS (RF–GPS) Antenna Cabling – continued Mounting Considerations Table 3-8 lists the Local GPS Head requires specific mounting considerations in order to properly observe the GPS satellites. Table 3-8: Local GPS Antenna Mounting Considerations Consideration n 1 The mounting pipe for the Local GPS Head should be mounted vertically with less than five (5) degrees of tilt. 2 The Local GPS Head requires a clear view of the sky, preferably to within ten (10) degrees of the horizon in all directions.
PAGE 113
Chapter 4: BTS and Cabling Installation Table of Contents MAY 2004 Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Procedure order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation of EV–DO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 114
Table of Contents 4 – continued Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TME Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 4-23 Compact BTS and HMS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compact BTS Installation . . . . . . . . . . . . . .
PAGE 115
Table of Contents MAY 2004 – continued Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Required Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the Span Line Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable Pin and Signal Information for Span Cabling . . . . . . . . . . . . . .
PAGE 116
Table of Contents – continued Notes 4 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU MAY 2004 PRELIMINARY
PAGE 117
Installation Overview Overview This chapter provides the procedures for BTS installation and cabling. The site cabling has been installed and routed to the location of the BTS. In this chapter, the cables will be attached to the unit(s). Cabling installation will be repeated as necessary for each unit at the BTS.
PAGE 118
Installation Overview – continued 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
PAGE 119
Connector Locations Connector Locations Figure 4-1 shows the location of the cable connectors on the BTS. The system configuration determines which connectors are used. Figure 4-2 is a detail of the connectors on the rear of the BTS. Figure 4-1: Rear View of BTS RGPS Connector and SDCX Module are shown. PWR 4 RF–GPD IN Note: 1. The LAN Connections should be terminated with 50–Ohm loads. 2. The Expansion TX and RX ports should be terminated with SMA 50–Ohm loads.
PAGE 120
Connector Locations – continued Figure 4-2: Detail of Antenna Connectors and DC Power (Rear of BTS) Circuit Breaker TME +0V –48V 20A 4 GROUND Location and GROUND LUG DC Power Terminal Strip Indoor/Outdoor Configuration Connectors cCLPA Connectors and Conduit Locations Refer to Figure 4-7 for connectors and conduit locations Outdoor Configuration Connectors TME Connectors and Conduit Locations Refer to Figure 4-16 for connectors and conduit locations PDE Conduit Locations Refer to Figure 4-23 for
PAGE 121
Attaching BTS to Mounting Rack Objective The objective of this procedure is to attach the BTS to the Rack. Background The mounting plate is attached to the Rack, then a mounting bracket is attached to the BTS. Finally, the BTS is attached to the Mounting Plate. Required Tools and Materials The following tools and materials are required to attach the BTS to the Mounting Plate. S S S S S MAY 2004 Torque driver wrench, 1/4–in.
PAGE 122
Attaching BTS to Mounting Rack – continued Procedure to Attach Mounting Plate to Rack Follow the procedure in Table 4-1 to attach the Mounting Plate to the Rack. Refer to Figure 4-3. Table 4-1: Procedure to Attach Mounting Plate to Rack Step Action 1 Determine where in the rack the Mounting Plate is to be attached. 2 Ensure that the mounting plate is level. 3 Set Mounting Plate similar to what is shown in Figure 4-3. Attach Mounting Plate to Rack using four (4) customer supplied rack screws.
PAGE 123
Attaching BTS to Mounting Rack – continued BTS Mounting Bracket Perform the procedure in Table 4-2 to attach the bracket to the BTS. Table 4-2: Procedure to Attach BTS Mounting Bracket Step Action 1 Atttach mounting bracket as indicated in Figure 4-4. 2 Using two (2) isolation washers and 2 M6 screws securely attach the mounting bracket to the forward most holes on the BTS. Torque screws to 5 N–M (44 in–lbs). Figure 4-4: Attaching Mounting Bracket to BTS 4 Hole not used.
PAGE 124
Attaching BTS to Mounting Rack – continued BTS to Mounting Plate Perform the procedure in Table 4-3 to attach the BTS to the Mounting Plate. Table 4-3: Procedure to Attach BTS to Mounting Plate Step Action NOTE The Compact BTS weighs 12 Kg (22 lbs). 4 1 Place BTS on Mounting Plate as indicated in Figure 4-5. BTS bracket holes align with rack holes. 2 Secure BTS bracket to rack using two (2) customer supplied screws. Torque screws to manufacturer’s specification.
PAGE 125
Attaching BTS to Mounting Rack – continued Figure 4-6: BTS Rear Attachment 4 One M6 screw and isolation washer for attaching BTS to mounting plate.
PAGE 126
Compact Combined Linear Power Amplifier Installation Objective This section contains general information for installing a Compact Combined Linear Power Amplifier (cCLPA). Cable Description The following cable in Table 4-4 is necessary to do this procedure. Table 4-4: DC Input Cable Description and Part Number Cable Qty. Part Number F 1 Customer Supplied Description DC input cable with crimped lugs, 8–10 AWG, 10 m, designed for –60 to –40 VDC power input.
PAGE 127
Compact Combined Linear Power Amplifier Installation – continued cCLPA Connectors Figure 4-7 shows the location of the cCLPA connectors. Figure 4-7: Bottom View of cCLPA FORWARD REFLECTED ANTENNA RX OUT TX INPUT 4 REMOVABLE HANDLE REMOVABLE HANDLE 20A Circuit Breaker DC INPUT DATA INPUT ti–cdma–wp–00298–v01–ildoc–ah IMPORTANT * The cCLPA requires its own DC power source that is different than the power source assigned to the Compact BTS.
PAGE 128
Compact Combined Linear Power Amplifier Installation – continued cCLPA Grounding Cable Description Since the length of this cable varies from site to site, no specific length is assigned. Table 4-6 lists the components required to build a ground cable. Table 4-6: Ground Cable and Lug Description and Part Number Cable Qty. Part Number A 1 Customer Supplied Ground cable, 6 -AWG, insulated copper wire.
PAGE 129
Compact Combined Linear Power Amplifier Installation – continued Follow the procedure in Table 4-7 to attach the ground cable to the cCLPA. Table 4-7: Procedure to Ground the cCLPA Step Action 1 If not already done, remove handles from cCLPA. 2 Retrieve ground lug and cabling. 2a Using a wire stripper, trim back 1/2–inch of the ground cable insulation from each end. 2b Using a crimp tool crimp the lug onto one end of the cable. 2c Attach the ground clamp to the opposite end of the ground cable.
PAGE 130
Compact Combined Linear Power Amplifier Installation – continued DC Power Connection Procedure A –48 VDC power source is required to supply the cCLPA. Follow the procedure in Table 4-8 to attach the DC Power cable to the cCLPA. Table 4-8: Procedure to Attach DC Power Cable to the cCLPA Step 4 Action 1 Set DC Power source circuit breaker to OFF. 2 Route cable (F) from DC Power source to the cCLPA. See Figure 4-10 3 Remove 8 screws securing I/O Panel cover and remove.
PAGE 131
Compact Combined Linear Power Amplifier Installation – continued Figure 4-10: DC Power Connection to cCLPA cCLPA Separate DC Power Source 4 –48 VDC CABLE DC IN CONNECTOR (F) ti–cdma–wp–00297–v01–ildoc–ah Close In View of cCLPA I/O Board DC Power Connection Data Cable Description and Part Number Table 4-9 lists the cable required to perform this procedure. Since the cable length will vary from site to site, it will be left to the customer to build the data cable desired.
PAGE 132
Compact Combined Linear Power Amplifier Installation – continued Table 4-9: Data Cable Description and Part Number Cable Qty. Part Number G 1 Customer Supplied 1 7687717T02 Description RJ45 cable for BTS to cCLPA Ferrite, clip–on core Data Cable Wiring Information Table 4-10 lists the wiring information required to manufacture the CBIO–to–cCLPA Data Cable. Figure 4-11 shows the location of Pin 1 on the RJ45 connector.
PAGE 133
Compact Combined Linear Power Amplifier Installation – continued BTS Data Cable Connection Procedure Once the Data Cable has been built, follow the procedure in Table 4-11 to connect the BTS Data cable to the cCLPA. Table 4-11: Procedure to Attach BTS Data Cable to cCLPA Step Action 1 If not already performed, remove 8 screws securing I/O Panel cover. 2 Route BTS Data cable to the cCLPA. See Figure 4-12. 3 Mate Data cable RJ45 plug to I/O Board RJ45 socket. See Figure 4-12.
PAGE 134
Compact Combined Linear Power Amplifier Installation – continued Figure 4-12: Data Cable Connection Diagram for Compact BTS to cCLPA NOTE: 1. Not to scale. 2.
PAGE 135
Compact Combined Linear Power Amplifier Installation – continued Outdoor cCLPA Installation The cCLPA is mounted on a bracket assembly and secured to a pole. Placement of cCLPA is up to the customer. The cCLPA is already weatherproofed, so there are no special weather related precautions required for outdoor installation. The maximum allowable TX cable loss (including surge arrestor) from the cCLPA to the BTS is 2.0 dB.
PAGE 136
Compact Combined Linear Power Amplifier Installation – continued Figure 4-13: Pole Mounting BracketAssembly 4 Figure 4-14 shows the cCLPA being attached to the Wall Mounting Bracket. Reference Figure 4-13 for the Pole Mounting Bracket Assembly.
PAGE 137
Thermal Management Enclosure Installation Objective This section contains general information for installing a Thermal Management Enclosure (TME). These procedures are utilized if the BTS site is configured for outdoor use. The purpose of the TME (Figure 4-15) is to protect the BTS from the weather. The Compact BTS is installed in the TME and some cables are connected to interior TME connectors, while others are routed out through access holes.
PAGE 138
Thermal Management Enclosure Installation – continued Environmental Requirements The following lists the environmental requirements of the TME: S Operate Temperature: –50° to +75°C S S S S Storage Temperature: –40° to +60°C Operating/Storage Humidity: 10 to 95%, non–condensing Cold Start: –40° to 0°C Seismic: Per Telecordia GR–63–CORE Zone 4 Weight Requirement S TME: 18 kg (40 lbs) S Heat Management System: 11.5 kg (26 lbs) S Wall Mounting Bracket: 2.5 kg (5.
PAGE 139
Thermal Management Enclosure Installation – continued TME Conduit Sizes The following are the conduit sizes required for connecting to the TME. Reference Figure 4-16. Table 4-13: TME Conduit Sizes No.
PAGE 140
Thermal Management Enclosure Installation – continued Table 4-14: Procedure to Pole Mount the TME Step Action 1 Slide non–buckle end of strap through openings in Pole Mounting Bracket Assembly. 2 Set Pole Mounting Bracket Assembly with straps at the desired height. NOTE Initial height is determined by customer. The bottom of the TME is a minimum of 1 meter from the ground. Adjust Pole Mounting Bracket Assembly to account for this minimum distance.
PAGE 141
Thermal Management Enclosure Installation – continued Figure 4-17: Wall Mounting Bracket and Pole Mounting Bracket Assembly Slots for hanging the TME Isolation Washer Pole Mounting Straps Shoulder Washer 4 M6 Screw Pole Rest Isolation Pad ti–cdma–wp–00317–v01–ildoc–ah Wall Mount Follow the procedure in Table 4-15 to wall mount the TME. Refer to Figure 4-17 for the Wall Mounting Bracket.
PAGE 142
Thermal Management Enclosure Installation – continued Table 4-15: Procedure to Install Mounting Bracket on a Wall Step 1 Action Select a suitable wall position such that the bottom of the TME is a minimum of 1 meter above the ground. NOTE Check site documentation for further information. 2 Position Wall Mounting Bracket on wall and mark hole locations. 3 Drill starter holes for the anchor bolts. 4 Secure Wall Mounting Bracket to wall using 8 M6 anchor bolts. Torque anchor bolts to 3.
PAGE 143
Thermal Management Enclosure Installation – continued Figure 4-18: TME Screw Mounting Location Screw Hole Location 4 ti–cdma–wp–00334–v01–ildoc–ah Screw Hole Locations MAY 2004 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY 4-27
PAGE 144
Compact BTS and HMS Installation Objective This section contains general information for installing a Compact BTS in a Thermal Management Enclosure (TME). WARNING Once the outdoor enclosures are installed, they are not to be used as steps or other types of climbing aids. They were not designed to support a person. 4 Compact BTS Installation Follow the procedure in Table 4-16 to install the BTS inside the TME.
PAGE 145
Compact BTS and HMS Installation – continued Figure 4-19: Thermal Management Enclosure and BTS HMS is removed for clarity.
PAGE 146
Compact BTS and HMS Installation – continued HMS Installation In an outdoor configuration, the HMS module is part of the Thermal Management Enclosure (TME). It is external to the TME and its purpose is to regulate the heating and cooling of the Compact BTS within the TME. See Figure 4-20. Figure 4-20: Heat Management System (HMS) INTERIOR VIEW 4 EXTERIOR VIEW ti–cdma–wp–00318–v01–ildoc–ah ti–cdma–wp–00319–v01–ildoc–ah Follow the procedure in Table 4-17 to install the Heat Management System (HMS).
PAGE 147
Compact BTS and HMS Installation – continued Table 4-17: Procedure to Install the HMS Step Action 2 Set the HMS on the hinges located on the TME (See Figure 4-21). 3 Use a driver wrench with socket to attach ground lug to HMS ground connection. 4 Connect the Data/DC PowerCable to HMS controller. 5 Dress cables as necessary. 6 Ensure that door swings freely and does not pinch any cables. 7 Close HMS and secure using the two draw latches. Fold draw latch handles down.
PAGE 148
Power Distribution Enclosure Installation Objective This section contains general information for installing a Power Distribution Enclosure (PDE) with Heat Exchanger (HX). See Figure 4-22. The optional PDE is a stand–alone unit external to the TME. When in use, the PDE provides Primary surge for input power, customer alarms, GPS, external antenna(s) and span lines; in addition to AC/DC power conversion for the SC480 base unit and optional external PAs.
PAGE 149
Power Distribution Enclosure Installation – continued Electrical The PDE is powered by AC voltage (customer supplied) in the range 154–286 VRMS at 47–63 Hz at 3100 Watts. The PDE outputs –54 Vdc at 2000 Watts (China). The PDE outputs +30 VDC at 2000 Watts (Domestic) Batteries if used, are located in a customer supplied external cabinet.
PAGE 150
Power Distribution Enclosure Installation – continued PDE Conduit Sizes The following are the conduit sizes required for connecting to the PDE. Reference Figure 4-23. Table 4-18: Conduit Sizes No.
PAGE 151
Power Distribution Enclosure Installation – continued Figure 4-24: PDE Detail Power Management Alarms Card (PMAC) 4 Punch Block DC Output Terminal Block AC Terminal Block ti–cdma–wp–00359–v01–ildoc–ah Power Supply Module DC Circuit Breakers Could be buttons or switches ti–cdma–wp–00345–v01–ildoc–ah MAY 2004 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY 4-35
PAGE 152
Power Distribution Enclosure Installation – continued Materials Tools The following tools are required to install the PDE: S S S S S Torque Screwdriver Drill, 3/8–inch or 1/2–inch drive Appropriate concrete or wood drill Bits Tie–wraps Alarms connector, 8–pin in–line, (Tyco, part number 103958–7) customer supplied S Bucklestrap Cutting Tool (Motorola P/N 6604809N01) for pole mounting bracket assembly 4 PDE Installation Figure 4-25 shows the Wall Mounting Bracket. and Mounting Bracket Assembly.
PAGE 153
Power Distribution Enclosure Installation – continued Mounting Bracket Assembly Procedure Pole Mount Follow the procedure in Table 4-19 to install the pole mounting bracket assembly and wall mounting bracket for pole mounting the PDE. WARNING Once PDE is installed, DO NOT use it as a step ladder. It will not support a person standing on top or hanging from it.
PAGE 154
Power Distribution Enclosure Installation – continued Table 4-20: Procedure to Install the Wall Mounting Bracket on a Wall Step 1 Action Select a suitable wall position such that the bottom of the PDE is a minimum of 1 meter above the ground. NOTE Check site documentation for further information. 4 2 Position Wall Mounting Bracket on wall and mark hole locations. 3 Drill starter holes for the anchor bolts. 4 Secure Wall Mounting Bracket to wall using 8 M6 anchor bolts. Torque anchor bolts to 3.
PAGE 155
Power Distribution Enclosure Installation – continued Heat Exchanger The Heat Exchanger (HX) is attached to the PDE and provides temperature regulation. Figure 4-27 shows the HX.
PAGE 156
Power Distribution Enclosure Installation – continued Heat Exchanger Details Figure 4-28 shows the main components of the HX. Figure 4-28: PDE Heat Exchanger Detail Internal Shield removed for clarity 4 Internal Loop Exhaust Blower Core Controller Internal Loop Inlet Blower Heat Exchanger Installation Follow the procedure in Table 4-21 to install the Heat Exchanger. Table 4-21: Procedure to Install the Heat Exchanger Step Action NOTE The HX weighs 12 kgs (26 lbs).
PAGE 157
Power Distribution Enclosure Installation – continued Table 4-21: Procedure to Install the Heat Exchanger Step Action 3 Use tie–wraps to dress cables as necessary. 4 Ensure that HX swings freely on the hinges and does not pinch and cables. Figure 4-29: PDE and Heat Exchanger Internal Shields removed for clarity 4 ti–cdma–wp–00342–v01–ildoc–ah PDE Cabling Table 4-22 shows the cabling pin–outs of the multiple layout punchblock for the PDE.
PAGE 158
Power Distribution Enclosure Installation – continued Table 4-22: PDE Punchblock Wiring Descriptions Unit Interface 4 Customer Output Signal Wire Color PB Pin CDI_3 103T CDI_3_RTN 103R CDI_4 104T CDI_4_RTN 104R CDI_5 105T CDI_5_RTN 105R CDI_6 106T CDI_6_RTN 106R CDI_7 107T CDI_7_RTN 107R CDI_8 108T CDI_8_RTN 108R CDO NC_0 109T CDO COM_0 109R CDO NO_0 110T CDO NC_1 110R CDO COM_1 201T CDO NO_1 201R CDO NC_2 202T CDO COM_2 202R CDO NO_2 203T CDO NC_3 203R CDO
PAGE 159
Power Distribution Enclosure Installation – continued Table 4-22: PDE Punchblock Wiring Descriptions Unit Interface RGPS Combined Compact Linear Power Amplifier 1 Power Management Enclosure Signal Wire Color PB Pin CDO COM_6 208R CDO NO_6 209T CDO NC_7 209R CDO COM_7 210T CDO NO_7 210R DATA_FROM_HEAD_POS 301T SYNC_FROM_HEAD_POS 301R SYNC_TO_HEAD_POS 302T DATA_TO_HEAD_POS 302R RGPS_+28V 303T RGPS_+28V 303R DATA_FROM_HEAD_NEG 304T SYNC_TO_HEAD_NEG 304R SYNC_TO_HEAD_NEG 305T
PAGE 160
Power Distribution Enclosure Installation – continued Table 4-22: PDE Punchblock Wiring Descriptions Unit Interface Signal 1X Span Line 4 Battery Backup Combined Compact Linear Power Amplifier 2 DO Span Line Wire Color PB Pin RX_RING_NET_A 404T RX_TIP_NET_A 404R TX_RING_NET_A 405T TX_TIP_NET_A 405R RX_RING_NET_B 406T RX_TIP_NET_B 406R TX_RING_NET_B 407T TX_TIP_NET_B 407R RX_RING_NET_C 408T RX_TIP_NET_C 408R TX_RING_NET_C 409T TX_TIP_NET_C 409R UNUSED 410T UNUSED 410R BA
PAGE 161
Power Distribution Enclosure Installation – continued Table 4-22: PDE Punchblock Wiring Descriptions Unit Interface MAY 2004 Signal Wire Color PB Pin TX_TIP_NET_1 510R RX_RING_NET_2 601T RX_TIP_NET_2 601R TX_RING_NET_2 602T TX_TIP_NET_2 603R RX_RING_NET_3 603T RX_TIP_NET_3 603R TX_RING_NET_3 604T TX_TIP_NET_3 604R Output Pin 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY 4 4-45
PAGE 162
Earth Ground Cabling Objective The objective of this procedure is to attach the earth ground cabling to the BTS. Indoor Grounding Considerations Refer to the site documentation for other grounding considerations. Rack Electrical Isolation on Concrete Slab – The onluy BTS and cCLPA grounding permitted is through the power cable and chassis ground connection. If the rack is installed on a concrete slab, it must be electrically isolated from the slab.
PAGE 163
Earth Ground Cabling – continued BTS Ground Procedure Follow the procedure in Table 4-24 to attach the ground cable. Table 4-24: Procedure to Attach the Earth Ground Cable Step Action NOTE Due to variability in rack placement, the rack is isolated from ground to reduce the chances of creating ground loops. 1 Retrieve ground lug and cabling. 1a Using a wire stripper, trim back 1/2–inch of the ground cable insulation from each end. 1b Using a crimp tool crimp the lug onto one end of the cable.
PAGE 164
Earth Ground Cabling – continued Figure 4-31: Grounding Location on BTS P/O BTS RF Panel GROUND LUG GROUND SCREW HOLES 4 M6 SCREWS Outdoor Grounding Considerations cCLPA The cCLPAs are designed to mount directly to the antenna tower. They have primary lightning protection on all terminations. There is a ground stud provided to connect the unit to the tower. If the cCLPAs are not mounted on the tower, they should be mounted as close as possible to an antenna ground system connection.
PAGE 165
Earth Ground Cabling – continued Site Requirements The enclosures are mounted according to the site documentation. Refer to Figure 2-10, Figure 2-13 through Figure 2-15 for dimensions and clearances and spacing information. Figure 4-32 shows an example of a mounted single system outdoor grounding diagram. Figure 4-33 shows an example of a mounted multiple unit system outdoor grounding diagram. Outdoor Grounding Procedure Follow the procedure in Table 4-25 to set up a site for grounding.
PAGE 166
Earth Ground Cabling – continued Figure 4-32: Typical Outdoor Grounding Configuration ANTENNA TOWER LEGEND: 1. PSA – Primary Surge Arrestor 2. SSA – Secondary Surge Arrestor 3. CDT – Conduit 4. SLD – Shielded Cable 5. EGD – Earth Ground 6. TWR – Tower Ground ANTENNAS TME and PDE are electrically isolated from ground. In addition, there are shielded RF cables connecting the TME and PDE.
PAGE 167
Earth Ground Cabling – continued Figure 4-33: Typical Multiple Outdoor Grounding Configuration LEGEND: 1. PSA – Primary Surge Arrestor 2. SSA – Secondary Surge Arrestor 3. CDT – Conduit 4. SLD – Shielded Cable 5. EGD – Earth Ground 6. TWR –Tower Ground 7. TSA –Tertiary Surge Arrestor ANTENNA TOWER ANTENNAS NOTE: TME and PDE are electrically isolated from ground. In addition, there are shielded RF cables connecting the TME and PDE.
PAGE 168
Earth Ground Cabling – continued PDE Ground Connection Figure 4-34 shows the ground location for the starter PDE and the other outdoor enclosures. Figure 4-34: Rear View of PDE NOTE: 1. in a multiple unit setup, all the grrounds are connected to the rear of the PDE (Starter). 2.
PAGE 169
BTS DC Power Cabling Objective The objective of this procedure is to attach the DC input cable to the BTS for indoor configuration. WARNING This equipment uses dangerous voltages and is capable of causing death. Use extreme caution when handling and testing this equipment. DC Cable Description The following cable in Table 4-26 is necessary to do this procedure. Table 4-26: DC Input Cable Description and Part Number Cable Qty.
PAGE 170
BTS DC Power Cabling (Indoor) – continued Table 4-27: Procedure to Connect DC Power to the BTS Step 3 For the –48 VDC version, proceed to step 3a. For the +27 VDC version, proceed to step 3c. 3a Connect the “+” wire (red) to the +0 V terminal. 3b Connect the “–” wire (blue) to the –48V terminal. Proceed to step 4. 3c Connect the “–” wire (black) to the RTN terminal. 3d Connect the “+” wire (red) to the +27 V terminal. Proceed to step 4.
PAGE 171
BTS DC Power Cabling – continued Connect DC Power to TME Procedure Use the following procedure in Table 4-28 to connect the DC voltage input cable to the TME. Refer to Figure 4-36 or Figure 4-37. Table 4-28: Procedure to Connect DC Power to the BTS Step Action 1 Ensure that DC power from PDE is disengaged (ciruit breaker set to OFF). 2 Route DC power cable through conduit to TME POWER Cable hole location. 3 Ensure that 1U and TME circuit breakers are disengaged (pulled out).
PAGE 172
BTS DC Power Cabling (Indoor) – continued TME 30A Circuit Breaker 1U 3A Circuit Breaker +27VDC +0VDC DC Power Connection Ground Location 4 NOTE: 1 A surge suppressor is recommended between the BTS and the DC power source.
PAGE 173
AC / DC Power Cabling Installation Objective The objective of this procedure is to install the AC power cabling and Battery Backup input cables to the Power Distribution Enclosure (PDE). CAUTION This equipment uses dangerous voltages and is capable of causing death. Use extreme caution when handling and testing this equipment. Earth connection is essential before connecting the power due to the presence of high earth leakage current.
PAGE 174
AC / DC Power Cabling Installation (Outdoor) – continued Battery Backup Power Cabling Procedure After PDE is installed, connect the Battery Backup DC power cable to the PDE according to the manufacturer’s installation specification. PDE to TME and cCLPA DC Power Cabling Procedure After PDE is installed, connect the DC power cables from the TME and cCLPA according to the manufacturer’s installation specification.
PAGE 175
Antenna Cabling Objective The objective of this procedure is to install the cabling for the antenna(s). This cabling is installed between the unit and the customer–supplied lightning arrestor(s). If lightning arrestor(s) are not required, the cabling connects directly to the antenna(s). Cable Descriptions The following cables in Table 4-30 are necessary to do this procedure. Table 4-30: Cable Descriptions and Part Numbers Cable Qty.
PAGE 176
Antenna Cabling – continued Figure 4-38: Antenna Cabling (With cCLPA) Antenna B +0V TME –48V 20 A LIGHTNING ARRESTOR (B) 4 (B) Antenna A 50–Ohm Loads LIGHTNING ARRESTOR (B) (B) 4-60 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 177
Antenna Cabling – continued Figure 4-39: Antenna Cabling with 2 cCLPAs (B) (B) (B) +0V TME –48V 20 A (B) 50–Ohm Loads Antenna A 4 cCLPA 1 LIGHTNING ARRESTOR (B) Antenna B cCLPA 2 LIGHTNING ARRESTOR (B) MAY 2004 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY 4-61
PAGE 178
Antenna Cabling – continued Figure 4-40: Antenna Cabling (Without cCLPA) Antenna B Antenna A LIGHTNING ARRESTOR 4 LIGHTNING ARRESTOR (B) (B) 4-62 +0V TME –48V 20 A 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 179
Span Line, RGPS, and RF GPS Cabling Objective The objective of this procedure is to install the span line and RGPS cabling. Cable Labels The cable designations are referenced to Table 3-1 in the “Cable Description” area of this chapter. Required Tools and Materials Table 4-32 provides the quantities and descriptions of the cables. 4 Table 4-32: List of Required Cables Cable Qty. Part Number Description C 1 T472AA RGPS cable, 15 m (50 ft.) T472AB RGPS cable, 38 m (125 ft.
PAGE 180
Span Line, RGPS, and RF–GPS Cabling – continued Figure 4-41: Span and RGPS Cabling Details Ferrite Beads LIGHTNING ARRESTOR C C1 Surge Protected Punchblock (Customer supplied) 4 D LIGHTNING ARRESTOR NOTE: Ferrite Beads are used in indoor configuration only.
PAGE 181
Span Line, RGPS, and RF–GPS Cabling – continued Cable Pin and Signal Information for Span Cabling Table 4-33 gives the pin and signal information for the Span cable.
PAGE 182
Span Line, RGPS, and RF–GPS Cabling – continued Connecting Customer–Defined Inputs to the CBIO The unit provides eight customer–defined inputs for connection to external contacts. Each input (a signal/ground pair) is monitored for an “OPEN” (>50 k Ohms) or “CLOSED” (<3 Ohms) condition. RGPS or RF–GPS Installation If RGPS is being installed, proceed to Table 4-36. If RF–GPS is being installed, proceed to Table 3-6. Cable Pinout Figure 4-42 shows the connector pins on cables C and C1.
PAGE 183
Span Line, RGPS, and RF–GPS Cabling – continued Table 4-35: Pinout for Cables C and C1 Cable C Wire Color Cable C1 Pin Signal Pin 6 No Connect Red No Connect 12 PPS Timing (–) Brown–Black 10 11 PPS Timing (+) Brown 2 Wire colors are the same for both cables. Procedure to Install the RGPS Head 4 The RGPS is connected to the BTS via the RGPS connector on the CBIO Board. See Figure 4-41. Site specific characteristics determine the GPS cabling that is installed.
PAGE 184
Span Line, RGPS, and RF–GPS Cabling – continued Table 4-36: Procedure for Installing the RGPS Head and Cabling Step Action 5 Connect RGPS cable (cable C1) to D–connector. Attach ferrite bead on the cable close to the BTS connector. 6 Route RGPS cable C (12–pin Deutsch connector) into the pipe. 7 Mate the 12–pin Deutsch connector of the RGPS Head cable and cable C. Refer to Figure 4-43. Tighten the spinning flange on the connector a quarter turn to secure the connection.
PAGE 185
Span Line, RGPS, and RF–GPS Cabling – continued Figure 4-44: RGPS Head THREADED MOUNT ADAPTER 12–PIN DEUTSCH TYPE MMP CONNECTOR 4 Connecting the RGPS Cable to Lightning Arrestor Figure 4-45 is a detail of the RGPS connections. Figure 4-46 is a detail of the Lightning Arrestor connections.
PAGE 186
Span Line, RGPS, and RF–GPS Cabling – continued Figure 4-46: RGPS Lightning Arrestor Wiring Yellow/Black Yellow Green White/Black White 4 Brown Green/Black Green White/Black White +17V DC Lines Brown/Black Yellow Cable Drain +17V DC Equipm ent Red Yellow/Black C (RGPS) TO RGPS RECEIVER Cable Drain Red/Black Blue +17V DC Lines Green/Black +17V DC Equipment C1 (RGPS) TO BTS UNIT Blue/Black +40V DC Lines Blue + 40V DC E quipm ent Blue/Black Red/Black Blue 1 White/Black 2 White 3 Gre
PAGE 187
Span Line, RGPS, and RF–GPS Cabling – continued Table 4-37: Procedure for Installing RF–GPS Antenna and Cabling Step Action 5 Attach the grounding kit to the mounting pole. 6 Connect one (1) N connector of the 50–feet superflex cable to the N jack of the RF–GPS antenna cable and route the other end of the cable down to the frame. 7 If not already done, attach RF–GPS Module to CBIO Board and secure using 4 M4 screws. 8 Route the cable to the RF–GPS connector at the rear of the BTS.
PAGE 188
Span Line, RGPS, and RF–GPS Cabling – continued Figure 4-47: RF–GPS Installation and Components 4–IN NOTE: 1. TOTAL WEIGHT FOR GPS ANTENNA ASSEMBLY – 0.65 LBS.
PAGE 189
Span Line, RGPS, and RF–GPS Cabling – continued Figure 4-48: Span and RF–GPS Cabling Details Customer I/O PWR RF–GPD IN J 4 D EXPANSION FRAME SYNC – OUT DAISY–CHAIN POWER SDCX POWER SDCX KIT NO. SDCX SERIAL NO.
PAGE 190
Customer Input / Output Cables Introduction The objective of this procedure is to attach the ferrite core onto the customer input and output cables. Cable Descriptions and Part Numbers Table 4-38 gives the cable descriptions and part numbers used to install the Customer I/O connectors. Table 4-38: Cable Descriptions and Part Numbers 4 Cable Qty.
PAGE 191
Site Cleanup – continued Table 4-39: Customer Input Connector Pinouts Pin Number Description 7 Customer Input 4/8 8 Customer Input 4/8 Return Output Pinouts Table 4-40 lists the pinouts for the Customer Output connectors.
PAGE 192
Site Cleanup Remove Protective Covering Remove any anti–static plastic or cloth sheeting that was used to cover the equipment. Lighting Fixtures Remove the masking tape from the fluorescent light fixtures. Tools Place all hand and power tools in the installation tool kit or other appropriate place. Note any tools that need replacement, cleaning, or adjustment. 4 Materials Place any leftover materials in a location specified by the site manager. Remove Debris Remove any packing material.
PAGE 193
Installation Completion Checklist Directions Fill out the installation completion checklist and make any necessary copies. You may copy this check sheet as needed.
PAGE 194
Installation Completion Checklist – continued Table 4-42: Indoor Installation Completion Checklist Status 4 No. Item 16 TME is cabled to PDE and cCLPA through conduit and conduit hubs on TME are tight. 17 PDE is cabled to TME through conduit and conduit hubs on PDE are tight. 18 cCLPA is cable to TME through conduit and and conduit hubs on cCLPA are tight. 19 Conduit is sufficiently grounded. 20 200–240 VAC is connected to PDE. 21 Battery backups (if used) are connected to the PDE.
PAGE 195
Installation Completion Checklist – continued Table 4-42: Indoor Installation Completion Checklist Status MAY 2004 No. Item 36 Installation hardware is removed. 37 The earth ground connections are secure between the earth ground and the Compact BTS. (Indoor) 38 The DC input cable is securely attached to the DC input connector. (Indoor) 39 The BTS–to–cCLPA cabling is secure (if applicable) (Indoor) 40 cCLPA connection to earth ground is secure (if cCLPA in use).
PAGE 196
Installation Completion Checklist – continued Notes 4 4-80 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 197
Chapter 5: Power Installation Table of Contents MAY 2004 Frame Configuration DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting Frame Configuration DIP Switch . . . . . . . . . . . . . . . . . . . . . . . Expansion Frame DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . Expansion 1 Frame DIP Switch . . . . . . . . . . . . . . . . . . . . . . .
PAGE 198
Table of Contents – continued Notes 5 1X SC480 BTS Hardware Installation, Optimization/ATP, and FRU PRELIMINARY MAY 2004
PAGE 199
Frame Configuration DIP Switch Introduction This section describes setting the DIP switch positions for starter/single frame and exapansion frames. The following sections describe BTS preparation before applying DC power. Setting Frame Configuration DIP Switch The frame configuration switch is located on the Compact BTS Input/Output (CBIO) Card of the BTS. Figure 5-1 shows the switch position for a starter /single frame configuration.
PAGE 200
Frame Configuration DIP Switch – continued Table 5-1: Frame ID Switch Position – Single/Starter Frame 1 2 3 4 UP UP –– –– –– = Don’t Care. These switch positions do not affect the BTS. Expansion Frame DIP Switch Settings Figure 5-2 shows the switch position for the expansion frames.